Axis Q1775-E manuel d'utilisation

AXIS Q1775-E Network Camera User Manual[...]

This manual is intended for administrators and users of AXIS Q1775-E Fixed Network Camera, and is applicable to rmware 5.85 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be us[...]

The power supply used with this product shall fulll the requirements for Safety Extra Low V oltage (SELV) and Limited P ower Source (LPS) according to IEC/EN/UL 60950-1. This product complies with IEC/EN/UL 60950-1 an- d IEC/EN/UL 60950-22, Safety of Information Technology Equipment. The product shall be grounded either through a shielded networ[...]

AXIS Q1775-E Network Camera T able of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

AXIS Q1775-E Network Camera T able of Contents Recording List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Continuous Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

AXIS Q1775-E Network Camera Safety Infor mation Safety Infor mation Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury . CAUTION Indicates a hazardous situation which, if not avoide[...]

AXIS Q1775-E Network Camera Hardware Overview Hardware Overview NO NO NO TICE TICE TICE Do not point the camera lens toward the sun or other high-intensity radiation sources because this could cause damage to the camera. 1 3 1 2 1 1 10 9 2 1 1 6 1 4 15 4 5 6 3 7 8 1. Status LED 2. 1/4” screw mount for wall/ceiling stand 3. P ower connector (block[...]

AXIS Q1775-E Network Camera Hardware Overview 1 2 4 5 6 7 3 8 1 1 1 2 1 3 1 4 1 5 1 6 1 7 10 9 1. Sunshield adjustment screw (2x) 2. Sunshield 3. Top cover 4. Network camera 5. Network connector (P oE) 6. Safety wire tab 7. Cable hole 8. Bottom cover screws (4x) 9. Heater Caution! May be hot 1 0. Bottom cover 1 1. Cable cover 12. Gasket 13. Network[...]

AXIS Q1775-E Network Camera Hardware Overview • Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > P orts & Dev[...]

AXIS Q1775-E Network Camera Hardware Overview LED Indicators Note • The Status LED can be congured to be unlit during normal operation. T o congure, go to Setup > System Options > P orts & Devices > LED . See the online help for more information. • The Status LED can be congured to ash while an event is active. • The [...]

AXIS Q1775-E Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer ® with Windows ® • Safari ® with OS X ® • Chrome TM or Firefox ® with other[...]

AXIS Q1775-E Network Camera Access the Product For Technical notes on this and other topics, visit the Axis Support web at www .axis.com/techsup Set the Root P assword To access the Axis product, you must set the password for the default administrator user root . This is done in the Congure Root P assword dialog, which opens when the product is [...]

AXIS Q1775-E Network Camera Access the Product Click Pulse to activate the product’s output port for a dened period of time. For information about how to enable and congure output buttons, see page 28 . The output button name may differ depending on the name entered in the I/O P orts conguration. Click the Active/Inactive buttons to manu[...]

AXIS Q1775-E Network Camera Access the Product Click the View Full Screen button and the video image will ll the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view . The Record button is used to record the current video stream on your computer . The location where the recording is saved can be specied in the[...]

AXIS Q1775-E Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Y our requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream p[...]

AXIS Q1775-E Network Camera Media Streams The AMC Control P anel can be used to congure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control P anel is automatically installed on rst use, after which it can be congured. Open the AMC Control P anel from: • Windows Control[...]

AXIS Q1775-E Network Camera Media Streams Note • <ip>= IP address • The Axis product supports QuickTime 6.5.1 and later . • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this. Access Audio Streams The Live View p[...]

AXIS Q1775-E Network Camera Set Up the Product Set Up the Product The Axis product can be congured by users with administrator or operator rights. T o open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have restricted access [...]

AXIS Q1775-E Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality . Y ou can congure the following: • Video stream settings. See page 19 . • Stream proles. See page 20 . • ONVIF Media Proles. See page 2 1 . • Camera settings. See page 2 1 . • Overlay image. Se[...]

AXIS Q1775-E Network Camera Video and Audio • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a xed amount. Alternatively , the frame rate can be set as Unlimited , which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay set[...]

AXIS Q1775-E Network Camera Video and Audio • When setting up recording using action rules. See Events on page 42 . • When setting up continuous recording. See Continuous Recording on page 49 . • In the Live View page – select the stream prole from the Stream prole drop-down list. For quick setup, use one of the predened stream pro[...]

AXIS Q1775-E Network Camera Video and Audio White Balance To change this setting go to Setup > Video & Audio > Camera Settings White balance is used to make colors in the image appear the same regardless of the color temperature of the light source. The Axis product can be set to automatically identify the light source and compensate for [...]

AXIS Q1775-E Network Camera Video and Audio Image freeze on PTZ - Select All movements to freeze the image while the camera is moving during a pan, tilt or zoom operation. Once the camera reaches its new position, the view from that position is shown. Presets freezes the image only when the camera moves between preset positions. Overlay Overlays ar[...]

AXIS Q1775-E Network Camera Video and Audio 3. Click Upload . 4. The Transparency Settings page is now displayed: - To make a color in the overlay image transparent, select Use transparency and enter the RGB hexadecimal value for the color . Example: T o make white transparent, enter FFFFFF . For more examples of hexadecimal values, see the online [...]

AXIS Q1775-E Network Camera Video and Audio Privacy Mask A privacy mask is a user-dened area that prevent users from viewing parts of the monitored area. Privacy masks appear as blocks of solid color or blurred image elements and are applied on the video stream. Privacy masks cannot be bypassed using the VAPIX® application programming interface[...]

AXIS Q1775-E Network Camera Video and Audio The Microphone power option is available for external microphones. 5V DC power or 12 V phantom power are available depending on if the microphone is unbalanced or balanced. Microphone power should only be used with microphones that have no battery . This setting should not be enabled when using a dynamic [...]

AXIS Q1775-E Network Camera Configure the Live View Page Configure the Live View Page Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 20 . • Default Viewer for Browser . See page 27 . • Viewer Settings. See page [...]

AXIS Q1775-E Network Camera Configure the Live View Page User Dened Links To display user-dened links in the Live View page, select the Show custom link option, give the link a name and then enter the URL to link to. When dening a web link do not remove the 'http://' from the URL address. Custom links can be used to run scripts [...]

AXIS Q1775-E Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if a PTZ driver has been uploaded. See Install PTZ Driver on page 3 1 . Preset P ositions A preset position is a saved view that can be used to quickly steer the camera to a specic position. A preset position consists of the following values: • P an a[...]

AXIS Q1775-E Network Camera PTZ (Pan Tilt Zoom) To add a guard tour: 1. Go to PTZ > Guard T our and click Add . 2. Enter a descriptive name. 3. Specify the pause length between runs. 4. Select an available preset position and click Apply . 5. Specify the Move Speed . 6. Specify the View Time in seconds or minutes. 7. Specify the View Order or se[...]

AXIS Q1775-E Network Camera PTZ (Pan Tilt Zoom) The P anel Shortcut Command Buttons list shows the user-dened buttons that can be accessed from the Live View page’s Ctrl panel . These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command butt[...]

AXIS Q1775-E Network Camera Detectors Detectors Camera T ampering Camera T ampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, spray-painted or severely defocused. T o send an alarm, for example an email, an action rule must be set up. To congure tampering detection: 1. Go to Detectors > Camera T a[...]

AXIS Q1775-E Network Camera Detectors For instructions, see Set Up Motion Detection Windows on page 33 . To control the number of motion detection alarms, the parameters Object Size , History and Sensitivity can be adjusted. See Motion Detection P arameters on page 33 . Once motion detection windows are congured, the Axis product can be congu[...]

AXIS Q1775-E Network Camera Detectors Recommended values 5–15% 60–90% 75–95% Default values 15% 90% 90% Note • T o trigger on small objects or movements, use several small motion detection windows rather than one large window , and select a low object size. • T o avoid triggering on small objects, select a high object size. • While moni[...]

AXIS Q1775-E Network Camera Applications Applications AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications for Axis products. For information about available applications, downloads, trials and licenses, go to www .axis.com/applications Note • The application AXIS Video[...]

AXIS Q1775-E Network Camera Applications If the Axis product is reset to factory default, uploaded applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings . 36[...]

AXIS Q1775-E Network Camera AXIS Video Motion Detection AXIS Video Motion Detection AXIS Video Motion Detection is an application that detects moving objects in the camera’s eld of view . When a moving object is detected, AXIS Video Motion Detection sends an alarm that can be used by the Axis product or by third-party software, to, for example[...]

AXIS Q1775-E Network Camera AXIS Video Motion Detection The default include area is a square that covers the whole image. Click on the icon to highlight the area. Use the mouse to reshape and resize the area so that it only covers the part of the image in which moving objects should be detected. The default square can be changed to a polygon with u[...]

AXIS Q1775-E Network Camera AXIS Video Motion Detection Note • Visual conrmation is disabled after 15 minutes. • After modifying a setting, click Save to apply the change. The video stream will be restarted and it may take a few seconds before the change is applied. • Enabling visual conrmation may introduce video latency . Ignore Filte[...]

AXIS Q1775-E Network Camera AXIS Video Motion Detection Short-Lived Object Ignore Filter The short-lived object lter is used to avoid detecting objects that only appear for a short period of time, such as light beams from a passing car and quickly moving shadows. Use the lter if such objects cause a lot of false detections. When the short-liv[...]

AXIS Q1775-E Network Camera AXIS Video Motion Detection 4. From the Trigger drop-down list, select Applications and then select VMD 3 . 5. Congure other settings as required. For example, to only record video during certain time periods, select a Schedule . 6. Under Actions , select Record Video from the Type drop-down list. 7. Select the stream[...]

AXIS Q1775-E Network Camera Events Events The Event pages allow you to congure the Axis product to perform actions when different events occur . For example, the product can start a recording or send an email notication when motion is detected. The set of conditions that denes how and when the action is triggered is called an action rule. [...]

AXIS Q1775-E Network Camera Events - Audio Detection – Trigger the rule when audio is detected. See Audio Detection on page 34 . - Live Stream Accessed – T rigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notications. - Shock Detection – Trigger the rule when the Axis produc[...]

AXIS Q1775-E Network Camera Events Actions Available actions include: • Day/Night Vision Mode – Set day mode (IR cut lter on) or night mode (IR cut lter off). • Defog Mode – Set Defog Mode to On or Off. This action may be used to change between the modes automatically . • Output P ort – Activate an I/O port to control an external [...]

AXIS Q1775-E Network Camera Events Recipient Use with action Notes Email Send Images Send Notication Send Video Clip An email recipient can contain multiple email addresses. FTP Send Images Send Video Clip SFTP Send Images Send Video Clip Encrypted le transfer using SSH File Transport Protocol (SFTP). SFTP is a more secure method than FTP but[...]

AXIS Q1775-E Network Camera Events address, port and authentication method. Optionally , select Use encryption to send emails over an encrypted connection. The server certicate can be validated using the certicates available in the Axis product. For information on how to upload certicates, see Certicates on page 53 . Create Schedules Sc[...]

AXIS Q1775-E Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 49 . • To set up action rules, see page 42 . • To access recordings, see Find Recordings on page 47 . • To play recordings, see Play Recording on page [...]

AXIS Q1775-E Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List . 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the lters. See also Find Recordings on page 47 . 3. Select the recording and click Play . The recording will [...]

AXIS Q1775-E Network Camera Recordings To remove a recording, select the recording and click Remove . Continuous Recording The Axis product can be congured to continuously save video to a storage device. For information about storage devices, see Storage on page 59 . To prevent the disk from becoming full, it is recommended to congure the dis[...]

AXIS Q1775-E Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. T o switch languages, go to Setup > Languages and rst upload the new language le. Browse and locate the le and click the Upload Language button. Sele[...]

AXIS Q1775-E Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may a[...]

AXIS Q1775-E Network Camera System Options HTTPS HTTPS (HyperText T ransfer Protocol over Secure Socket Layer , or HTTP over SSL) is a web protocol providing encrypted browsing. HTTPS can also be used by users and clients to verify that the correct device is being accessed. The security level provided by HTTPS is considered adequate for most commer[...]

AXIS Q1775-E Network Camera System Options Certicates Certicates are used to authenticate devices on a network. Typical applications include encrypted web browsing (HTTPS), network protection via IEEE 80 2.1X and secure upload of images and notication messages for example via email. Two types of certicates can be used with the Axis prod[...]

AXIS Q1775-E Network Camera System Options • Synchronize with computer time – Sets date and time according to the computer’s clock. With this option, date and time are set once and will not be updated automatically . • Synchronize with NTP Server – Obtains date and time from an NTP server . With this option, date and time settings are upd[...]

AXIS Q1775-E Network Camera System Options Pinging the product is still possible when the service is disabled. Assign IP Address Using ARP/Ping The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power . 1. Acquire a free static IP address on the same network segment as the compute[...]

AXIS Q1775-E Network Camera System Options AXIS Internet Dynamic DNS Service AXIS Internet Dynamic DNS Service assigns a host name for easy access to the product. For more information, see www .axiscam.net To register the Axis product with AXIS Internet Dynamic DNS Service, go to System Options > Network > TCP/IP > Basic . Under Services ,[...]

AXIS Q1775-E Network Camera System Options HTTP The HTTP port used by the Axis product can be changed under System Options > Network > TCP/IP > Advanced . In addition to the default setting, which is 80, any port in the range 1 0 24–65535 can be used. HTTPS The HTTPS port used by the Axis product can be changed under System Options > [...]

AXIS Q1775-E Network Camera System Options Note H.264 video streams will not be available if the RTSP server is disabled. SOCKS SOCKS is a networking proxy protocol. The Axis product can be congured to use a SOCKS server to reach networks on the other side of a rewall or proxy server . This functionality is useful if the Axis product is locat[...]

AXIS Q1775-E Network Camera System Options To use SNMP v3, HTTPS must be enabled, see HTTPS on page 52 . To enable SNMP v3, check the box and provide the initial user password. Note The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 64 [...]

AXIS Q1775-E Network Camera System Options Mount and Unmount SD Card NO NO NO TICE TICE TICE To prevent corruption of recordings, the SD card should always be unmounted before it is ejected. The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the car[...]

AXIS Q1775-E Network Camera System Options It is possible to change the passphrase without reformatting the card. Open Storage Management , click Encrypt and enter the old and new passphrases. The passphrase can only be changed when the card is mounted. Ongoing recordings will not be affected if the passphrase is changed. To disable encryption, unm[...]

AXIS Q1775-E Network Camera System Options • P an Tilt Zoom is used to control a PTZ device. The PTZ device requires a driver . See Install PTZ Driver for more information. Drivers can be downloaded from www .axis.com • Generic T CP/IP allows the Axis product to receive data and send commands via TCP/IP . Select the desired P ort T ype from the[...]

AXIS Q1775-E Network Camera System Options Support Support Overview The System Options > Support > Support Overview page provides information on troubleshooting and contact information, should you require technical assistance. See also Troubleshooting on page 65 . System Overview To get an overview of the Axis product’s status and settings,[...]

AXIS Q1775-E Network Camera System Options File Upload Files, for example webpages and images, can be uploaded to the Axis product and used as custom settings. T o upload a le, go to System Options > Advanced > File Upload . Uploaded les are accessed through http://<ip address>/local/<user>/<file name> where <user&g[...]

AXIS Q1775-E Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version. The latest version may contain a correction that xes your particular problem. The cur[...]

AXIS Q1775-E Network Camera Troubleshooting The IP address is being used by another device Disconnect the Axis product from the network. Run the Ping command (in a Command/DOS window , type ping and the IP address of the product): • If you receive: Reply from <IP address>: bytes=32; time=10... this means that the IP address may already be i[...]

AXIS Q1775-E Network Camera Troubleshooting P oor rendering of H.264 images Ensure that your graphics card is using the latest driver . The latest drivers can usually be downloaded from the manufacturer’s website. Color saturation is different in H.264 and Motion JPEG Modify the settings for your graphics adapter . Refer to the adapter’s docume[...]

AXIS Q1775-E Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur . To identify the source of the problem, check the System Log under System Options > Support > Logs & Repo[...]

AXIS Q1775-E Network Camera T echnical Specifications T echnical Specifications Camera Image sensor Progressive scan CMOS 1/2.8" with full HD (1 080/60p) Lens 3.8 mm (wide)-38 mm (tele), F1.8–3.4 Horizontal angle of view 67.8°–8.1° V ertical angle of view 4 1.2°–4.5° Autofocus, Automatic day/night IR lter , Focus near limit: 320[...]

AXIS Q1775-E Network Camera T echnical Specifications Analytics Video motion detection, Tampering alarm, Audio detection, Gatekeeper , AXIS Camera Application Platform enabling installation of additional applications Event triggers Detectors, Hardware, Input signal, PTZ, Edge storage events, System, Time Event actions File upload: FTP , SFTP , HTT[...]

AXIS Q1775-E Network Camera T echnical Specifications Connectors I/O Connector 4-pin terminal block 1 2 3 4 For an example diagram, see Connection Diagrams on page 72 . Note The I/O connector is connected to the housing (fan/heater) on delivery . In the case of a fan or heater error , an input signal will be triggered in the camera. Set up an acti[...]

AXIS Q1775-E Network Camera T echnical Specifications Function Pin Notes RS485/RS422 RX/TX A 1 RS485/RS422 RX/TX B 2 (RX) For full duplex RS485/RS422 (RX/TX) For half duplex RS485 RS485/RS422 TX A 3 RS485/RS422 TX B 4 (TX) For full duplex RS485/RS422 Connection Diagrams I/O Connector 1 2 A B 1 0 V DC (-) 2 DC output 12 V, max 50 mA A I/O congur[...]

AXIS Q1775-E Network Camera T echnical Specifications • Heavy network utilization due to poor infrastructure. Bandwidth affected. • Viewing on poorly performing client computers lowers perceived performance. Frame rate affected. • Running multiple AXIS Camera Application Platform (ACAP) applications simultaneously may affect the frame rate a[...]

User Manual V er . M2.2 AXIS Q1775-E Network Camera Date: July 2015 © Axis Communications AB, 20 15 P art No. 6289 1[...]