Français dropdown-ico

CDA HCG 730 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation CDA HCG 730. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel CDA HCG 730 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation CDA HCG 730 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation CDA HCG 730 devrait contenir:
- informations sur les caractéristiques techniques du dispositif CDA HCG 730
- nom du fabricant et année de fabrication CDA HCG 730
- instructions d'utilisation, de réglage et d’entretien de l'équipement CDA HCG 730
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage CDA HCG 730 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles CDA HCG 730 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service CDA en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées CDA HCG 730, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif CDA HCG 730, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation CDA HCG 730. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Built-in cooking hob HCG 730 HCG 740 Befor e operating this hob, please r ead these instructions car efully Users Operating Instructions Installation instructions GB[...]

  • Page 2

    2 Dear Customer, Thank you for choosing one of our products. The warnings and tips given below are intended to protect your safety and that of others. They will also help you make the most of your appliance. Keep this booklet in a safe place. It will be useful if you, or anyone else, have any questions about use of the appliance. This appliance mus[...]

  • Page 3

    3 Important: This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and there- fore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non domes- tic environment i.e. a semi commercial, co[...]

  • Page 4

    4 BEFORE USING FOR THE FIRST TIME • Read the instructions carefully before installing and using the appliance • After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your supplier or a qualified engineer. • Remove all packaging and do not leave the packing material (plastic bags, po[...]

  • Page 5

    5 IMPORT ANT SAFEGUARDS & RECOMMENDA TIONS • Do not carry out any cleaning or maintenance without first disconnecting the appli- ance from the electrical supply. • During and after use of the hob, certain parts will become very hot. Do not touch hot parts. • After use always ensure that the control knobs are in the “ ● ” OFF positio[...]

  • Page 6

    6 COOKING POINTS 1. Auxiliary burner (A) - 1,00 kW 2. Semirapid burner (SR) - 1,75 kW 3. Rapid burner (R) - 3,00 kW 4. Triple-ring burner (TR) - 3,50 kW CONTROL P ANEL DESCRIPTION 5. Auxiliary burner control knob (1) 6. Rear left semirapid burner control knob (2) 7. Triple ring burner control knob (4) 8. Rapid burner control knob (3) 9. Front right[...]

  • Page 7

    7 GAS BURNERS Gas flow to the burners is adjusted by turning the knob illustrated in figs. 3a - 3b which control the valves. Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: ✓ full circle ● = closed valve ✓ symbol – = maximum aperture or flow ✓ symbol = minimum apertu[...]

  • Page 8

    8 Figure 4 LIGHTING THE BURNERS Models without safety cut-off valves In order to light the burner, you must: Models without electric ignition : 1 – To light one of the gas burners, hold a flame (e.g. a match) close to the top part of the burner, push in and turn the relative knob (fig. 3b) in an anti- clockwise direction (fig. 4), pointing the kn[...]

  • Page 9

    9 LIGHTING THE BURNERS Models fitted with safety cut-off valves In order to light the burner, you must: Models without electric ignition : 1 – To light one of the gas burners, hold a flame (e.g. a match) close to the top part of the burner, push in and turn the relative knob (fig. 3a) in an anti- clockwise direction (fig. 4), pointing the knob in[...]

  • Page 10

    10 PAN DIAMETER BURNER MINIMUM MAXIMUM Auxiliary 12 cm 14 cm Semirapd 16 cm 24 cm (1) Rapid 24 cm 26 cm Triple-ring 26 cm 28 cm Woks (2) max 36 cm do not use pans with concave or convex bases (1) front right burner, maximum diameter 22 cm. (2) Models with triple-ring burner and with wok pan adapter supplied: wok pans have to be used only with the s[...]

  • Page 11

    11 WRONG CORRECT Figure 6a Figure 6b CORRECT USE OF TRIPLE-RING BURNER ✓ The flat-bottomed pans are to be placed directly onto the pan-support. ✓ To use the WOK you need to place the proper stand (supplied with some models only) in order to avoid any faulty operation of the triple-ring burner (Fig. 6a). IMPORTANT: The special grille for wok pan[...]

  • Page 12

    12 GENERAL TIPS ✓ Before cleaning the hob switch it off and wait for it to cool down. ✓ Clean with a cloth, hot water and soap or liquid detergent. ✓ Do not use products which are abrasive, corrosive or chlorine based. ✓ Do not use steel pads. ✓ Do not leave acid or alkaline substances (vinegar, salt, lemon juice, etc.) on the hob. ✓ Do[...]

  • Page 13

    13 BURNERS AND GRIDS ✓ These parts can be removed and cleaned with appropriate products. ✓ After cleaning, the burners and their flame spreaders must be well dried and correct- ly replaced. ✓ It is very important to check that the burner flame spreader and the cap have been correctly positioned. Failure to do so can cause serious problems. ?[...]

  • Page 14

    14 Figure 7 Figure 8 F C Probe " T " - models with safety cut-off valves only Electrode " S " - models with electric ignition only CORRECT POSITIONING OF THE BURNERS ✓ It is very important to check that the burner flame spreader “ F ” and the cap “ C ” have been correctly positioned (see figs. 7 and 8). Failure to do s[...]

  • Page 15

    15 Figure 9 CORRECT POSITION OF TRIPLE RING BURNER The triple ring burner must be correctly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arrow. The burner correctly positioned must not rotate (fig. 10). Then position the cap A and the ring B (figs. 10 - 11). A B Figure 10 Figure 11[...]

  • Page 16

    16 T ips for installation Location ✓ The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or space containing a bath or a shower. ✓ The appliance must not be installed in a bed-sitting room of less than 20 m 3 . ✓ The appliance is designed and approved for domestic use only and should not be inst[...]

  • Page 17

    17 TECHNICAL INFORMA TION FOR THE INST ALLER In order to install the cooktop into the kitchen fixture, a hole with the dimen- sions shown in fig. 13 has to be made, bearing in mind the following: ✓ within the unit, between the bottom of the cooktop and the upper sur- face of a shelf there must be a clear- ance of at least 30 mm. It is absolutely [...]

  • Page 18

    18 APPL YING THE SEALS ✓ Turn the cooktop upside down. ✓ Spread the longer seal “ A ” around the left, rear and right sides as shown in figure 15a. ✓ With a cutter or a scissors cut the excess seal “ C ” and retain it for next use (figure 15b). ✓ Spread the seal “ B ” around the left, front and right edges of the cooktop as show[...]

  • Page 19

    19 F ASTENING THE INST ALLA- TION BRACKETS Each cooktop is provided with an instal- lation kit including brackets and screws for fastening the top to fixture panels from 2 to 4 cm thick. ✓ Turn the cooktop upside down and fasten the brackets “ F and R ” to the appropriate socket holes, without tightening the screws “ B ” for the moment. ?[...]

  • Page 20

    20 V entilation r equir ements ✓ The appliance should be installed into a room or space with an air supply in accor- dance with BS 5440-2: 2000. ✓ For rooms with a volume of less than 5 m 3 - permanent ventilation of 100 cm 2 free area will be required. ✓ For rooms with a volume of between 5 m 3 and 10 m 3 a permanent ventilation of 50 cm 2 f[...]

  • Page 21

    21 Gas supply r equirements IMPORTANT NOTE This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on the appliance). ✓ Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification. The appliances are manufactured for conver[...]

  • Page 22

    22 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a C.O.R.G.I. registered installer. Installers shall take due account of the provisions of the relevant British Standards Code of Practice, the Gas Safety Regulations and the Building Standards (Scotland)(Consolidation) Regulations issued by the S[...]

  • Page 23

    23 CONNECTION TO THE GAS SUPPL Y ✓ Be careful when flexible pipes are used that they do not come into contact with moving parts. ✓ To maintain the thickness of 3 cm, the hob is fitted with a channel to contain the connection pipe. ✓ The gas inlet union can be turned in the direction required after the elbow fitting “ C ” and nut “ A ”[...]

  • Page 24

    24 If installation is to be carried out using a flexible connector (to BS669), then the follow- ing points must be adhered to: Note: The gas installation pipes and the final connection to the appliance connecting pipe shall be sufficient size to maintain the heat output of the appliance as specified under installation . 1. The appliance flexible co[...]

  • Page 25

    25 Figure 19 Figure 20 J J Conversion to Natural Gas or LPG REPLACING THE BURNER INJECTORS If the NATURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be purchased by contacting the After-Sales Service. Choose the injectors to be replaced according to the table on next page . The injector diameter, expressed in hundredths [...]

  • Page 26

    26 T able for the choice of the Injectors Cat: II 2H3+ [Hs - kW] [Hs - kW] Ø injecteur Ø injecteur [1/100 mm] [1/100 mm] Auxiliary (A) 1,00 0,30 0,50 0,72 (X) Semirapid (SR) 1,75 0,45 0,65 0,97 (Z) Rapid (R) 3,00 0,75 0,85 1,15 (Y) Triple ring (TR) 3,30 1,50 0,95 1,35 (T) G30/G31 28-30/37 mbar REDUCED POWER (HS - kW) NOMINAL POWER (HS - kW) BURNE[...]

  • Page 27

    27 ADJUSTING THE GAS BURNER MINIMUM For taps with adjusting screw inside the shaft (fig. 21): ✓ using a screwdriver max. diameter 3 mm turn the screw inside the tap shaft until the flame setting is correct. For taps with adjusting screw on the body (fig. 22): ✓ using a screwdriver turn screw "A" until the flame setting is correct. ✓[...]

  • Page 28

    28 IMPORTANT: The appliance must be installed by a qualified technician accord- ing with the current local regulations and in compliance with the manufac- turer instructions. Incorrect installation may be dangerous and the manufacturer can not be held responsible. Warning! This appliance must be earthed A properly earthed three pin plug (fused at 3[...]

  • Page 29

    29 230 V L1 N(L 2 ) PE SECTION OF THE SUPPL Y CABLES - TYPE “H05V2V2-F” resistant to temperatures of 90°C 230 VAC 50 Hz 3 x 0,75 mm 2 ✓ The electrical cable must be connected to the terminal board following the diagram of Fig. 24. The appliance must be earthed. The manufacturer declines all responsibility for any problem caused by failure to[...]

  • Page 30

    30 Appliance servicing CDA provide a quality and effective after-sales service to cover all your servicing needs. Please attach your receipt to this page for safekeeping. Please help us to help you by having the following information available when booking a service-call: 1. Model type, make and model – see the product data plate. 2. Evidence of [...]

  • Page 31

    31 Guarantee CDA appliances carry a five-year parts and a one-year labour guarantee. CDA will repair or replace any defect or part attributable to faulty material or workman- ship. Within the first year this will be free of both labour and parts charges. After the first year and within five years, the parts will be supplied free of charge provided [...]

  • Page 32

    P70 Series Gas Cooktop The Group Ltd Harby Road ● Langar ● Nottingham ● NG13 9HY ● UK VAT No : 528 7168 19 ● Registered in England : 2621460 Cod. 1103114 ß2[...]