Chevrolet 2010 Traverse manuel d'utilisation

2010 Chevrolet T raverse Owner Manual M In Brief ... ..................... 1 - 1 Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information . . . . . . . . 1-4 V ehicle Features . . . . . . . . . . . . . 1-15 Performance and Maintenance . . . . . . . . . . . . . . . . 1-20 Keys, Doors and Windows . . . 2-1 Keys and Locks . . . . . . . . . . . . . . . 2-2 D o o r s... .................. .....2 - 9 V ehicle Security . . . . . . . . . . . . . . 2-13 Exterior Mirrors . . . . . . . . . . . . . . . 2-16 Interior Mirrors . . . . . . . . . . . . . . . . 2-19 Windows . . . . . . . . . . . . . . . . . . . . . 2-20 R o o f..........................2 - 2 2 Seats and Restraints . . . . . [...]

2010 Chevrolet T raverse Owner Manual M V ehicle Care . . . . . . . . . . . . . . . . . 10-1 General Information . . . . . . . . . . 10-2 V ehicle Checks . . . . . . . . . . . . . . . 10-4 Headlamp Aiming . . . . . . . . . . . 10-27 Bulb Replacement . . . . . . . . . . 10-27 Electrical System . . . . . . . . . . . . 10-29 Wheels and T ires . . . . . . . . . . . 10-36 Jump Starting . . . . . . . . . . . . . . . 10-78 T owing . . . . . . . . . . . . . . . . . . . . . . 10-82 Appearance Care . . . . . . . . . . . 10-86 Service and Maintenance . . . 1 1-1 General Information . . . . . . . . . . 1 1-1 Scheduled Maintenance . . . . . . 1 1-2 Recommended Fluids, Lubricants, and Parts . . . . . . . [...]

Introduction iii GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem, are registered trademarks, and the name T raverse is a trademark of General Motors Corporation. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name “ General Motors of Canada Limited ” for Chevrolet Motor Division wherever it appears in this manual. Keep this manual in t[...]

iv Introduction Using this Manual T o quickly locate information about the vehicle, use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Danger , Warnings, and Cautions W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death. { W ARNING These mean there is something that could hurt you or other people. Notice: This means there is something that could result in property or vehicl[...]

Introduction v V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant T emperature O : Exterior Lamps # : Fog Lamps . : Fuel Gauge + : Fuses i : Headlamp High/Low-Beam Changer _ : High V oltage j : LA TCH System Child Restraints * : Malfunction Indicator Lamp : : Oil Pressure } : Power [ : Power Flow Options / : Remote V ehicle Start > : Safety Belt Reminders 7 : T[...]

vi Introduction 2 NOTES[...]

In Brief 1-1 In Brief Instrument Panel Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information Initial Drive Information . . . . . . . . 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . 1-4 Remote V ehicle Start . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . 1-5 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Windows . . . . . . . . . . . . . . . . . . . . . . 1-6 Seat Adjustment . . . . . . . . . . . . . . 1-6 Second Row Seats . . . . . . . . . . . 1-7 Third Row Seats . . . . . . . . . . . . . . 1-7 Heated Seats . . . . . . . . . . . . . . . . . 1-8 Heated and V entilated Seats . . . . . . . . . . . . .[...]

1-2 In Brief Instrument Panel[...]

In Brief 1-3 A. Windshield Wiper/Washer on page 5 ‑ 5 . B. Instrument Cluster on page 5 ‑ 1 1 . C. Steering Wheel Controls on page 5 ‑ 3 . D. Instrument Panel Storage on page 4 ‑ 1 . E. AM-FM Radio on page 7 ‑ 6 . F . Air V ents on page 8 ‑ 12 . G. Exterior Lamp Controls on page 6 ‑ 1 . H. Instrument Panel Illumination Control on page 6 ‑ 4 . I. Cruise Control on page 9 ‑ 31 . J. Steering Wheel Adjustment on page 5 ‑ 2 . K. Horn on page 5 ‑ 5 . L. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) (With DIC Buttons) on page 5 ‑ 22 or Driver Information Center (DIC) (Without DIC Buttons) on page 5 ‑ 28 . M. Climate Control Systems on page 8 [...]

1-4 In Brief Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual. Remote Keyless Entry (RKE) System The RKE transmitter is used to remotely lock and unlock the doors from up to 60 m (195 feet) away from the vehicle. Press K to unlock the driver door . Press K again within five seconds to unlock all remaining doors. Press Q to lock all doors. Lock and unlock feedback can be personalized. T o open or close the liftgate, press and hold & until the liftgate begins to move. Press L and rele[...]

In Brief 1-5 The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension. Remote start can be extended only once. Canceling a Remote Start T o cancel a remote start: . Aim the RKE transmitter at the vehicle and press and hold / until the parking lamps turn off. . T urn on the hazard warning flashers. . T urn the ignition switch on and then off. See Remote V ehicle Start on page 2 ‑ 5 . Door Locks T o lock or unlock a door manually: . From the inside use the door lock knob on the window sill. . From the outside turn the key toward the front or rear of the vehicle, or press the Q or " button on the Remote Keyless Entry (RKE) transmitter . Power Door L[...]

1-6 In Brief . Press the liftgate button on the center console. . Press the touchpad switch on the outside liftgate handle. For more information see Liftgate on page 2 ‑ 9 . Windows On vehicles with power windows, the switches are on the driver door armrest. Each passenger door has a switch that controls only that window . Press the switch to lower the window . Pull the switch up to raise it. For more information, see Power Windows on page 2 ‑ 20 . Seat Adjustment Manual Seats 1. Pull the handle under the seat to unlock the seat. 2. Slide the seat to the desired position and release the handle. T ry to move the seat to be sure it is locked in place. Power Seats A. Power Seat Adjustment C[...]

In Brief 1-7 Move the seat forward or rearward by moving the control (A) forward or rearward. Raise or lower the entire seat by moving the control (A) up or down. See Power Seat Adjustment on page 3 ‑ 3 . T o raise or recline the seatback, tilt the top of the control (B) forward or rearward. See Reclining Seatbacks on page 3 ‑ 6 . Press the front or rear of the control (C) to increase or decrease lumbar support. See Lumbar Adjustment on page 3 ‑ 6 . Second Row Seats T o access the third row , pull the sliding seat lever forward so that the seat cushion folds and the entire seat slides forward. See Rear Seats on page 3 ‑ 10 . Third Row Seats The third row seats can be folded forward o[...]

1-8 In Brief Heated Seats Heated Front Seats The heated seat controls are located on the center console. The engine must be running to operate them. I : Press to turn on the heated seatback. J : Press to turn on or off the heated seat and seatback. For more information see Heated Front Seats on page 3 ‑ 8 . Heated and V entilated Seats On vehicles with this feature, the controls are on the front doors near the handle. H : Press to ventilate the seat. z : Press to heat the seat. For more information see Heated and V entilated Front Seats on page 3 ‑ 9 . Head Restraint Adjustment Do not drive until the head restraints for all occupants are installed and adjusted properly . For more informa[...]

In Brief 1-9 Sensing System for Passenger Airbag United States Canada The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag, seat ‐ mounted side impact airbags, and roof ‐ rail airbags are not affected by the passenger sensing system. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. See Passenger Sensing System on page 3 ‑ 38 for more information. Mirror Adjustment Exterior Mirrors Controls for the outside power mirrors are located on the driver door armrest. 1. Press (A) or (B) to select the driver or passenger side mirror . 2. Press one of the four arrow[...]

1-10 In Brief Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, push the mirror toward the vehicle. Push the mirror outward to return it to the original position. Interior Mirror If equipped, a manual inside rearview mirror can be adjusted so that the driver can see behind the vehicle more clearly . Hold the mirror in the center to move it up or down and side to side. Use the day/night adjustment to help prevent glare from the headlamps behind you. Move the lever located at the base of the mirror , to the right for nighttime use and to the left for daytime use. For vehicles with an automatic dimming rearview mirror , the mirror will automa[...]

In Brief 1-1 1 Power Tilt Wheel For vehicles with the power tilt and telescope wheel, the control is on the left side of the steering column. . Push the control up or down to tilt the steering wheel up or down. . Push the control forward or rearward to move the steering wheel toward the front or rear of the vehicle. See Steering Wheel Adjustment on page 5 ‑ 2 . Interior Lighting Dome Lamps The dome lamps are located in the overhead console and above the rear seat passengers. The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. T o manually turn them on, turn the instrument panel brightness control clockwise to the farthest position[...]

1-12 In Brief Exterior Lighting The exterior lamps control is located on the instrument panel, to the left of the steering wheel. 9 : Turns the automatic light control on or off. AUTO : Automatic operation of the headlamps at normal brightness and other exterior lamps. ; : Manual operation of the parking lamps and other exterior lamps. 2 : Manual operation of the headlamps and other exterior lamps. For more information, see: . Exterior Lamp Controls on page 6 ‑ 1 . . Daytime Running Lamps (DRL)/ Automatic Headlamp System on page 6 ‑ 3 . . Delayed Headlamps on page 6 ‑ 3 . Windshield Wiper/W asher The windshield wiper/washer lever is located on the left side of the steering column. T ur[...]

In Brief 1-13 Windshield W asher J : Press the button at the end of the turn signal/lane change lever to spray washer fluid on the windshield. See Windshield Wiper/Washer on page 5 ‑ 5 . Climate Controls A. Fan Control B. T emperature Control C. Air Delivery Mode Control D. Air Conditioning E. REAR (Rear Climate Control) F . Air Recirculation G. Rear Window Defogger[...]

1-14 In Brief A. Fan Control B. AUTO C. Defrost D. Air Recirculation E. REAR (Rear Climate Control) F . Air Delivery Mode Control G. Driver Side T emperature Control H. Display I. Power (On/Off) J. Rear Window Defogger K. Air Conditioning L. P ASS (Passenger) M. Passenger Side T emperature Control See Climate Control Systems on page 8 ‑ 1 or Dual Automatic Climate Control System on page 8 ‑ 4 (If Equipped). For more information about the rear climate control, see Rear Climate Control System (Rear Climate Control Only) on page 8 ‑ 10 or Rear Climate Control System (Rear Climate with Rear Seat Audio) on page 8 ‑ 1 1 .[...]

In Brief 1-15 V ehicle Features Radio(s) Radio with CD, DVD, and USB Port O : Press to turn the system on and off. Turn to increase or decrease the volume. BAND: Press to choose between FM, AM, or XM ™ , if equipped. f : Select radio stations. © ¨ : Seek or scan stations. 4 : Change the display between the radio station frequency and the time, if equipped. While the ignition is off, press 4 to display the time. For more information about these and other radio features, see Operation on page 7 ‑ 2 . Storing a Favorite Station A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio F A V button. Pres[...]

1-16 In Brief Setting the Clock T o set the time and date for the radio with CD, DVD, and USB Port: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN, then press O , to turn the radio on. 2. Press G to display HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year). 3. Press the pushbutton located under any one of the labels to be changed. 4. T o increase or decrease the time or date, turn f clockwise or counter ‐ clockwise. For detailed instructions on setting the clock for the vehicles specific audio system, see Clock on page 5 ‑ 8 . Satellite Radio V ehicles with an XM ™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. XM Satellit[...]

In Brief 1-17 The Bluetooth-enabled cell phone must be paired with the in-vehicle Bluetooth system before it can be used in the vehicle. Not all phones will support all functions. See Bluetooth on page 7 ‑ 45 . Steering Wheel Controls w / x : Press to change favorite radio stations, select tracks on a CD/DVD, or to navigate tracks or folders on an iPod ® or USB device. b g : Press to silence the vehicle speakers only . Press again to turn the sound on. Press and hold longer than two seconds to interact with OnStar ® or Bluetooth systems. + e − e : Increases or decreases volume. c : Press to reject an incoming call, or to end a call. SRCE : Press to switch between the radio, CD, and for[...]

1-18 In Brief Driver Information Center (DIC) (With DIC Buttons) T o access the DIC, some vehicles have buttons located on the instrument panel. V : Press to set or reset certain functions and to turn off or acknowledge messages on the DIC. U : Press to customize the feature settings on your vehicle. See V ehicle Personalization (With DIC Buttons) on page 5 ‑ 40 for more information. T : Press to display the oil life, park assist on vehicles with this feature, units, tire pressure readings on vehicles with this feature, RKE transmitter programming, and compass calibration and zone setting on vehicles with this feature. 3 : Press this button to display the odometer , trip odometers, fuel ra[...]

In Brief 1-19 Storage Compartments For vehicles with a second row center console, open each area to access the storage compartment inside. Press the buttons (B, C) on the front of the consoles to access the upper and lower storage areas. Increase the storage area by folding the top of the console forward. Lift up on rear console handle (A) and pull forward. See Floor Console Storage on page 4 ‑ 2 . Power Outlets The vehicle may have four accessory power outlets which can be used to plug in electrical equipment, such as a cellular phone. The power outlets are located: . On the instrument panel below the climate controls. . Under the center floor console cupholder . . At the rear of the cent[...]

1-20 In Brief Sunroof The ignition must be in ON/RUN or ACC/ACCESSORY to operate the sunroof and power sunshade. See Retained Accessory Power (RAP) on page 9 ‑ 17 The switch to operate the front sunroof is on the headliner above the rearview mirror . V ent: Press the front or rear of the switch to vent or close the sunroof. Express-open/Express-close: From the closed position, press and release the rear or front of the switch to express-open or express-close the sunroof. For more information see Sunroof on page 2 ‑ 22 . Performance and Maintenance StabiliT rak ® The traction control system limits wheel spin and the StabiliTrak system assists with directional control of the vehicle in di[...]

In Brief 1-21 Tire Pressure Monitor This vehicle may have a T ire Pressure Monitor System (TPMS). The T ire Pressure Monitor System alerts you when a significant reduction in pressure occurs in one or more of your vehicle ’ s tires by illuminating the low tire pressure warning light on the instrument cluster . If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label located on the driver side center pillar (B pillar). See V ehicle Load Limits on page 9 ‑ 12 . The warning light will remain on until the tire pressure is corrected. Y ou may notice during cooler conditions that the low tire pressure [...]

1-22 In Brief Resetting the Oil Life System 1. T urn the ignition to ON/RUN, with the engine off. 2. If the vehicle has Driver Information Center (DIC) buttons: Press the vehicle information button until OIL LIFE REMAINING displays. If the vehicle does not have Driver Information Center (DIC) buttons: The vehicle must be in P (Park) to access this display . Press the trip odometer reset stem until OIL LIFE REMAINING displays. 3. If the vehicle has Driver Information Center (DIC) buttons: Press and hold the set/ reset button until “ 100% ” is displayed. Three chimes sound and the CHANGE ENGINE OIL SOON message goes off. If the vehicle does not have Driver Information Center (DIC) buttons:[...]

In Brief 1-23 Roadside Assistance Program Roadside Assistance U.S.: 1-800-CHEV -USA (1-800-243-8872) TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Chevrolet, you are automatically enrolled in the Chevrolet Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day , 365 days a year , minor repair information or towing arrangements. Roadside Assistance and OnStar If you have a current OnStar subscription, press the OnStar button and the current GPS location will be sent to an OnStar Advisor who will assess your problem, contact Roadside Assistance, and relay exact location to get you the help you need. Chevrolet Ow[...]

1-24 In Brief Crisis Assist, Stolen V ehicle Assistance, V ehicle Diagnostics, Remote Door Unlock, Roadside Assistance, T urn ‐ by ‐ T urn Navigation and Hands ‐ Free Calling are available on most vehicles. Not all OnStar services are available on all vehicles. For more information see the OnStar Owner's Guide or visit www .onstar .com (U.S.) or www .onstar .ca (Canada), contact OnStar at 1-888-4-ONST AR (1 ‐ 888 ‐ 466 ‐ 7827) or TTY 1 ‐ 877 ‐ 248 ‐ 2080, or press Q to speak with an OnStar advisor 24 hours a day , 7 days a week. For a full description of OnStar services and system limitations, see the OnStar Owner's Guide in the glove box. OnStar service is subjec[...]

In Brief 1-25 OnStar Steering Wheel Controls This vehicle may have a T alk/Mute button that can be used to interact with OnStar hands-free calling. See Steering Wheel Controls on page 5 ‑ 3 for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions. See the OnStar Owner's Guide for more information. Y our Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard. If the light next to the OnStar buttons is red, the system may not be functioning properly . Press Q and request a vehicle diagnostic. If the light appears clear (no light is appearing), your OnStar subscription has expir[...]

1-26 In Brief 2 NOTES[...]

Keys, Doors and Windows 2-1 Keys, Doors and Windows Keys and Locks K e y s .......................... 2 - 2 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . 2-2 Remote Keyless Entry (RKE) System Operation . . . . . . . . . . . 2-3 Remote V ehicle Start . . . . . . . . . 2-5 Door Locks . . . . . . . . . . . . . . . . . . . 2-7 Power Door Locks . . . . . . . . . . . . 2-8 Delayed Locking . . . . . . . . . . . . . . 2-8 Automatic Door Locks . . . . . . . . . 2-8 Lockout Protection . . . . . . . . . . . . 2-8 Safety Locks . . . . . . . . . . . . . . . . . . 2-8 Doors Liftgate . . . . . . . . . . . . . . . . . . . . . . . . 2-9 V ehicle Security V ehicle Security . . [...]

2-2 Keys, Doors and Windows Keys and Locks Keys { W ARNING Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window . Do not leave the keys in a vehicle with children. The key is used for the ignition and all door locks. The key has a bar-coded key tag that the dealer or qualified locksmith can use to make new keys. Store this information in a safe place, not in the vehicle. See [...]

Keys, Doors and Windows 2-3 If there is a decrease in the RKE operating range: . Check the distance. The transmitter may be too far from the vehicle. . Check the location. Other vehicles or objects may be blocking the signal. . Check the transmitter's battery . See “ Battery Replacement ” later in this section. . If the transmitter is still not working correctly , see your dealer or a qualified technician for service. Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 60 m (195 feet) away from the vehicle. There are other conditions which can affect the performance of the transmitter . See Remote Keyless Entry (RKE) System on [...]

2-4 Keys, Doors and Windows If enabled through the DIC, the parking lamps flash twice to indicate unlocking has occurred. See Vehicle Personalization (With DIC Buttons) on page 5 ‑ 40 . Pressing K on the RKE transmitter disarms the content theft ‐ deterrent system. See Anti-Theft Alarm System on page 2 ‑ 13 . & (Power Liftgate): Press and hold until the liftgate begins to move to open or close the liftgate. The taillamps flash and a chime sounds to indicate when the liftgate is opening or closing. L (V ehicle Locator/Panic Alarm): Press and release to locate the vehicle. The parking lamps flash and the horn sounds three times. Press and hold L for more than two seconds to activate [...]

Keys, Doors and Windows 2-5 1. Separate the transmitter with a flat, thin object, such as a flat head screwdriver . . Carefully insert the tool into the notch located along the parting line of the transmitter . Do not insert the tool too far . Stop as soon as resistance is felt. . T wist the tool until the transmitter is separated. 2. Remove the old battery . Do not use a metal object. 3. Insert the new battery , positive side facing down. Replace with a CR2032 or equivalent battery . 4. Snap the transmitter back together . Remote V ehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. / (Remote Start): This button is located on the [...]

2-6 Keys, Doors and Windows When the vehicle starts the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system will operate automatically if the vehicle has the automatic system, or at the same setting as when the vehicle was last turned off. If the vehicle has an automatic climate control system and heated seats, the heated seats turn on during colder outside temperatures and shut off when the key is turned to ON/RUN. See Heated Front Seats on page 3 ‑ 8 or Heated and V entilated Front Seats on page 3 ‑ 9 for more information. The rear window defogger and heated mirrors, if the vehicle has them, turn on during c[...]

Keys, Doors and Windows 2-7 Conditions in Which the Remote Start Will Not Work The vehicle cannot be started using the remote start feature if the key is in the ignition, the hood is open, or if there is an emission control system malfunction. The engine turns off during a remote start if the coolant temperature gets too high or if the oil pressure gets low . V ehicles that have the remote vehicle start feature are shipped from the factory with the remote vehicle start system enabled. The system may be enabled or disabled through the DIC if the vehicle has DIC buttons. See “ REMOTE ST ART ” under V ehicle Personalization (With DIC Buttons) on page 5 ‑ 40 for additional information. If [...]

2-8 Keys, Doors and Windows Power Door Locks The power door lock switches are located on the front doors. " (Unlock): Press to unlock the doors. Q (Lock): Remove the key from the ignition and press to lock the doors. Delayed Locking When locking the doors with the power lock switch and a door or the liftgate is open, the doors will lock five seconds after the last door is closed. Y ou will hear three chimes to signal that the delayed locking feature is in use. Pressing the power lock switch twice or the lock button on the RKE transmitter twice will override the delayed locking feature and immediately lock all the doors. This feature will not operate if the key is in the ignition. This f[...]

Keys, Doors and Windows 2-9 Open the rear doors to access the security locks on the inside edge of each door . T o set the locks, insert a key into the slot and turn it to the horizontal position. The door can only be opened from the outside with the door unlocked. T o return the door to normal operation, turn the slot to the vertical position. Doors Liftgate Manual Liftgate Operation { W ARNING Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even[...]

2-10 Keys, Doors and Windows T o open the liftgate, press the touchpad on the underside of the liftgate handle. The vehicle must be in P (Park) to open the liftgate. T o close the liftgate, use the pull cup or strap. The liftgate has an electric latch. If the battery is disconnected or has low voltage, the liftgate will not open. The liftgate will resume operation when the battery is reconnected and charged. If the battery is properly connected and has adequate voltage, and the liftgate still will not function, the vehicle should be taken to a dealer for service. Power Liftgate Operation { W ARNING Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or wi[...]

Keys, Doors and Windows 2-1 1 { W ARNING Y ou or others could be injured if caught in the path of the power liftgate. Make sure there is no one in the way of the liftgate as it is opening and closing. Notice: If you open the liftgate without checking for overhead obstructions such as a garage door , you could damage the liftgate or the liftgate glass. Always check to make sure the area above and behind the liftgate is clear before opening it. The power liftgate can be power opened and closed in the following ways: . Press and hold the power liftgate button on the RKE transmitter until the liftgate starts moving. Power Liftgate Button on Center Console . Press the liftgate button on the cente[...]

2-12 Keys, Doors and Windows The power liftgate may be temporarily disabled under extreme temperatures or under low battery conditions. If this occurs, the liftgate can still be operated manually . If the vehicle is shifted out of P (Park) while the power function is in progress, the liftgate power function will continue to completion. If the vehicle is shifted out of P (Park) and the vehicle accelerates before the power liftgate latches closed, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. The power liftgate must be closed and latched before driving. If the liftgate is power opened and the support struts have lost pressure, the lights will flash and a c[...]

Keys, Doors and Windows 2-13 Manual Operation of Power Liftgate T o change the liftgate to manual operation, press the switch on the center console to OFF . With the power liftgate disabled and all of the doors unlocked, the liftgate can be manually opened and closed. T o open the liftgate, press the touchpad on the handle on the outside of the liftgate and lift the gate open. T o close the liftgate, use the pull cup to lower the liftgate and close. The liftgate latch will power close. Always close the liftgate before driving. If the RKE button or the power close button on the liftgate is pressed while power operation is disabled, the lights will flash three times, but the liftgate will not [...]

2-14 Keys, Doors and Windows When the door is closed, the security light stops flashing and stays on solid for approximately 30 seconds. The content theft deterrent alarm is not armed until the security light goes off. If the delayed locking feature is active, the alarm is not activated until all doors are closed and the security light goes off. . Press Q when the driver door is closed. The security light comes on solid for approximately 30 seconds and then goes off. The content theft deterrent alarm is not armed until the security light goes off. The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. If a locked door is open[...]

Keys, Doors and Windows 2-15 Immobilizer See Radio Frequency Statement on page 13 ‑ 17 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada. Immobilizer Operation This vehicle has P ASS-Key ® III+ (Personalized Automotive Security System) theft-deterrent system. P ASS-Key ® III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY or ST ART from the LOCK/OFF position. Y ou do not have to manually arm or disarm the system. The security light comes on if there is a problem with[...]

2-16 Keys, Doors and Windows T o program the new additional key: 1. V erify that the new key has a 1 stamped on it. 2. Insert the already programmed key in the ignition and start the engine. If the engine does not start, see your dealer for service. 3. After the engine has started, turn the key to LOCK/OFF , and remove the key . 4. Insert the key to be programmed and turn it to the ON/RUN position within five seconds of the original key being turned to the LOCK/OFF position. The security light turns off once the key has been programmed. 5. Repeat Steps 1 through 4 if additional keys are to be programmed. If the P ASS-Key ® III+ key is lost or damaged, see your dealer or a locksmith to have [...]

Keys, Doors and Windows 2-17 Power Mirrors Controls for the outside power mirrors are located on the driver door armrest. T o adjust each mirror: 1. Press (A) or (B) to select the driver or passenger side mirror . 2. Press one of the four arrows located on the control pad to adjust the mirror . 3. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen. 4. Press either (A) or (B) again to deselect the mirror . Folding Mirrors Manual Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, pull the mirror toward the vehicle. Push the mirror outward, to return it to the original position. Heated Mirrors For veh[...]

2-18 Keys, Doors and Windows Driving with the Blind Spot Mirror Actual Mirror View 1. When the approaching vehicle is a long distance away , the image in the main mirror is small and near the inboard edge of the mirror . 2. As the vehicle gets closer , the image in the main mirror gets larger and moves outboard. 3. As the vehicle enters the blind zone, the image transitions from the main mirror to the blind spot mirror . 4. When the vehicle is in the blind zone, the image only appears in the blind spot mirror . Using the Outside Mirror with the Blind Spot Mirror 1. Set the main mirror so that the side of the vehicle can just be seen and the blind spot mirror has an unobstructed view . 2. Whe[...]

Keys, Doors and Windows 2-19 Interior Mirrors Manual Rearview Mirror Adjust the inside rearview mirror to see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. Use the day/night adjustment to help prevent glare from the headlamps behind you. Move the lever to the right for nighttime use and to the left for daytime use. V ehicles with OnStar ® have three additional control buttons located at the bottom of the mirror . See your dealer for more information about OnStar and how to subscribe to it. See the OnStar ® owner guide for more information on the services OnStar provides. Automatic Dimming Rearview Mirror The vehicle may have an automatic[...]

2-20 Keys, Doors and Windows Windows { W ARNING Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather . Power Windows { W ARNING Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed (Continued)[...]

Keys, Doors and Windows 2-21 The driver door also has switches that control the passenger and rear windows. The power windows work with the ignition in ACC/ ACCESSORY , ON/RUN or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9 ‑ 17 . Press the switch to lower the window . Pull up on the front edge of the switch to raise the window . Express-Up/Express-Down Windows A window with the express ‐ up/down feature allows it to be raised or lowered without holding the switch. Press or pull the window switch fully and release it to activate the express feature. The express mode can be canceled by pressing or pulling the switch. Programming the Power Win[...]

2-22 Keys, Doors and Windows Sun Visors Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window . Swing the sun visor to the side to cover the side window . It can be moved along the rod from side-to-side in this position also. Lighted Visor V anity Mirror The vehicle has lighted visor vanity mirrors on both the driver and passenger sun visors. Pull the sun visor down and lift the mirror cover to turn the lamps on. Roof Sunroof The ignition must be in ON/RUN or ACC/ACCESSORY to operate the sunroof and power sunshade. See Retained Accessory Power (RAP) on page 9 ?[...]

Keys, Doors and Windows 2-23 roof sealing area using a clean cloth, mild soap, and water . Do not remove grease from sunroof. V ent: From the closed position, press and hold the front of the switch to vent the sunroof. Press and hold the rear of the switch to close the sunroof. Express-open/Express-close: From the closed position, press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof. The front sunshade must be opened and closed manually . Push up on the sunshade handle to open the sunshade. Manual Sunshades On a vehicle with only manual sunshades, press the button on the sunshade handle to release it and [...]

2-24 Keys, Doors and Windows 2 NOTES[...]

Seats and Restraints 3-1 Seats and Restraints Head Restraints Head Restraints . . . . . . . . . . . . . . . 3-2 Front Seats Seat Adjustment . . . . . . . . . . . . . . 3-3 Power Seat Adjustment . . . . . . . 3-3 Lumbar Adjustment . . . . . . . . . . . 3-6 Reclining Seatbacks . . . . . . . . . . 3-6 Heated Front Seats . . . . . . . . . . . 3-8 Heated and V entilated Front Seats . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Rear Seats Rear Seats . . . . . . . . . . . . . . . . . . 3-10 Third Row Seats . . . . . . . . . . . . . 3-12 Safety Belts Safety Belts . . . . . . . . . . . . . . . . . . 3-14 How to Wear Safety Belts Properly . . . . . . . . . . . . . . . . . . . . 3-18 Lap-Shoulder[...]

3-2 Seats and Restraints Head Restraints The vehicle's front seats have adjustable head restraints in the outboard seating positions. { W ARNING With head restraints that are not installed and adjusted properly , there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly . Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash. 1. Pull the head restraint up to raise it. T o lower the head restraint, press the release button, located on the hea[...]

Seats and Restraints 3-3 Front Seats Seat Adjustment { W ARNING Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving. A. Manual Seat Adjustment Handle B. Driver Seat Height Adjuster . C. See Reclining Seatbacks on page 3 ‑ 6 . T o adjust a manual seat: 1. Lift the handle (A) under the seat to unlock it. 2. Slide the seat and release the handle. T ry to move the seat to be sure it is locked in place. T o manually raise or lower the seat, move the lever (B) repeatedl[...]

3-4 Seats and Restraints Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward. The vehicle may have additional features to adjust the power seat: . Raise or lower the entire seat by moving the power seat adjustment control (A) up or down. . Raise or lower the front part of the seat cushion by moving the front of the control up or down. . Raise or lower the rear part of the seat cushion by moving the rear of the control up or down. Memory Seat and Mirrors On vehicles with the memory package, the controls for this feature are located on the driver door panel. The controls are used to program and recall memory settings for the driver seat and ou[...]

Seats and Restraints 3-5 Using the Remote Keyless Entry (RKE) transmitter to enter the vehicle, with the remote recall memory feature on, causes automatic seat and mirror adjustment. There is no adjustment when the position has not been changed by another seating position or the easy exit feature. See “ MEMORY SEA T RECALL ” under V ehicle Personalization (With DIC Buttons) on page 5 ‑ 40 for more information. T o stop recall movement of the memory feature at any time, press one of the power seat controls, memory buttons, or power mirror buttons. If something has blocked the driver seat while recalling a memory position, the driver seat recall may stop working. If this happens, press t[...]

3-6 Seats and Restraints Lumbar Adjustment Manual Lumbar On vehicles with this feature, the handle is located on the inboard side of the seatback. Move the handle forward or rearward to increase or decrease lumbar support. Power Lumbar On vehicles with power lumbar , the control is located on the outboard side of the seat. See “ Power Lumbar ” under Power Seat Adjustment on page 3 ‑ 3 for more information. T o increase or decrease lumbar support, press and hold the front or rear of the control (C). Release the control when the seatback reaches the desired level of lumbar support. Reclining Seatbacks Manual Reclining Seatbacks { W ARNING Y ou can lose control of the vehicle if you try t[...]

Seats and Restraints 3-7 T o return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked. Power Reclining Seatbacks In vehicles with seats that have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat. See Power Seat Adjustment on page 3 ‑ 3 for more information. T o recline the seatback: . T ilt the top of the control (B) rearward. . T o bring the seatback forward, tilt the top of the control forward. { W ARNING Sitting in a reclined position when the vehicle [...]

3-8 Seats and Restraints Heated Front Seats { W ARNING If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. T o reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat. On vehicles with heated front seats, the controls are located on the center console. T o operate the heated seats the engine must be running. I (Heated Seatback): [...]

Seats and Restraints 3-9 Heated and V entilated Front Seats { W ARNING If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. T o reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat. On vehicles with the heated and ventilated seat feature, the controls are located on the front doors near the door handle. H (V entilated Seat): Pr[...]

3-10 Seats and Restraints Rear Seats A. Seat Adjustment Handle B. Reclining Seatback Strap C. Sliding Seat Lever Entering and Exiting the Third Row { W ARNING Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. T o access the third row: 1. Remove objects on the fl[...]

Seats and Restraints 3-1 1 5. Pull the sliding seat lever (C) forward and move the seatback forward. The seat cushion will fold, and the entire seat will slide forward. Returning the Seat to the Seating Position T o return the second row seat to its normal seating position: 1. Remove objects on the floor behind the second row seat or in the seat tracks on the floor . 2. Pull the seatback rearward until it is locked in place. 3. Slide the seat rearward by pushing on the seatback until it is locked into place. 4. Push down on the rear of the seat cushion until it is locked in place. 5. Push and pull on the seatback and seat cushion to make sure they are locked in place. 6. Check that the safet[...]

3-12 Seats and Restraints Third Row Seats { W ARNING Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place. The third row seats can be folded forward or removed. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. T o fold the seatback: 1. Remove anything on or under the seat. 2. Disconnect the rear [...]

Seats and Restraints 3-13 T o return the seatback to the seating position: 1. Raise the seatback into place by using the pullstrap from the rear of the vehicle, or by pushing it into place from inside the vehicle. 2. The headrest must be locked into place before sitting in the seat. { W ARNING If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3. Push and pull on the seatback to make sure it is locked in place. { W ARNING A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a cras[...]

3-14 Seats and Restraints 5. Remove the seat by tilting it slightly upward, and then pulling it out of the rear of the vehicle in one motion. 6. Replace the bolts in the floor holes for storage. Installing the Third Row Seats 1. Before installing the seat the seatback must be folded forward. See “ Folding the Seatback ” earlier in this section. The seats must be placed in the proper locations to attach correctly . The wider seat must be installed on the driver side and the narrower seat on the passenger side. Remove the bolts from the holes in the floor before installing the seats. 2. Place the seat on the vehicle floor so that the front seat hooks are on the vehicle bars. 3. Reinstall t[...]

Seats and Restraints 3-15 { W ARNING It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly . This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 5 ‑ 13 for additional information. In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have [...]

3-16 Seats and Restraints Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel...[...]

Seats and Restraints 3-17 or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y ou could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety belt, even if you are upside down. Q: If my vehicle has airbags, why should I have to wear safety be[...]

3-18 Seats and Restraints Q: If I am a good driver , and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver , but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur within 40 km (25 miles) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 65 km/h (40 mph). Safety belts are for everyone. How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and childre[...]

Seats and Restraints 3-19 applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash. Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury . Th[...]

3-20 Seats and Restraints Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. Q: What is wrong with this? A: The belt is buckled in the wrong buckle.[...]

Seats and Restraints 3-21 { W ARNING Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. Q: What is wrong with this? A: The belt is over an armrest. { W ARNING Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes unde[...]

3-22 Seats and Restraints Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury . Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. Y ou could also severely injure internal organs like your liver or spleen. The shoulder belt should go over the shoulder and across the chest. Q: What is wrong with this? A: The belt is behind the body .[...]

Seats and Restraints 3-23 { W ARNING Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury . Y ou might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest. Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is[...]

3-24 Seats and Restraints 2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly . If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly . If the shoulder portion of a passenger belt is pulled out all the way , the child restraint locking feature may be engaged. If this happens, let the belt go back all the way and start again. 3. Push the latch plate into the buckle until it clicks. 4. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 3 ‑ 29 . Position the release butto[...]

Seats and Restraints 3-25 T o unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Slide the latch plate up the safety belt webbing when the safety belt is not in use. The latch plate should rest on the stitching on the safety belt, near the guide loop on the side wall. Before a door is closed, be sure the safety belt is out of the way . If a door is slammed against a safety belt, damage can occur to both the safety belt and the vehicle. Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the[...]

3-26 Seats and Restraints Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly . They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met. And, for vehicles with side impact airbags, safety belt pretensioners can help tighten the safety belts in a side crash or a rollover event. Pretensioners work only once. If the pretensioners activate in a crash, they will need to be replaced, and probably other new parts for the ve[...]

Seats and Restraints 3-27 pulling on the handle behind the seatback. The comfort guide will now be accessible. Third Row Center Position Pull the comfort guide out of its storage location and then return the headrest to its upright position. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.[...]

3-28 Seats and Restraints { W ARNING A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder . T o remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide into its storage location or on its storage clip. Safety Belt Use During Pregnancy Safety[...]

Seats and Restraints 3-29 The best way to protect the fetus is to protect the mother . When a safety belt is worn properly , it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly . Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you an extender . When you go in to order it, take the heaviest coat you will wear , so the extender will be long enough for you. T o help avoid personal injury , do not let someone else use it, and use it only for the seat it is made to fit. The e[...]

3-30 Seats and Restraints Replacing Safety Belt System Parts After a Crash { W ARNING A crash can damage the safety belt system in the vehicle. A damaged safety belt system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure the safety belt systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. After a minor crash, replacement of safety belts may not be necessary . But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer to have the safety belt assemblies inspected or replaced. New parts and repairs may b[...]

Seats and Restraints 3-31 All of the airbags in the vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening. For frontal airbags, the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger . With seat-mounted side impact airbags, the word AIRBAG will appear on the side of the seatback closest to the door . With roof-rail airbags, the word AIRBAG will appear along the headliner or trim. Airbags are designed to supplement the protection provided by safety belts. Even though today's airbags are also designed to help reduce the risk of injury from the force o[...]

3-32 Seats and Restraints { W ARNING Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward. Safety belts help keep you in position before and during a crash. Always wear your safety belt, even with airbags. The driver should sit as far back as possible while still maintaining control of the vehicle. Occupants should not lean on or sleep against the door or side windows in seating positions with seat-mounted side impact airbags and/or roof-rail airba[...]

Seats and Restraints 3-33 Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side. Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door .[...]

3-34 Seats and Restraints Driver Side shown, Passenger Side similar The roof-rail airbags for the driver , right front passenger , passengers behind the driver and right front passenger , and the third row outboard passengers are in the ceiling above the side windows. { W ARNING If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear . Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not use seat accessories that block [...]

Seats and Restraints 3-35 Frontal airbags may inflate at different crash speeds. For example: . If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object. . If the vehicle hits an object that deforms, the airbags could inflate at a different crash speed than if the vehicle hits an object that does not deform. . If the vehicle hits a narrow object (like a pole), the airbags could inflate at a different crash speed than if the vehicle hits a wide object (like a wall). . If the vehicle goes into an object at an angle, the airbags could inflate at a different crash speed than if the vehicle goes straight into the object[...]

3-36 Seats and Restraints determined by the location and severity of the side impact. In a rollover event, roof-rail airbag deployment is determined by the direction of the roll. What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module. Frontal airbag modules are located inside the steering wheel and instrument panel. For vehicles with seat-mounted side impact airbags, there are airbag modules in the side of the front seatbacks cl[...]

Seats and Restraints 3-37 The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle. { W ARNING When an airbag inflates, there may be dust in the air . This dust could cause breathing problems for people with a history of asthma or other breathing trouble. T o avoid this, everyone in the vehicle should get out as soon as it is safe to do so. If you have breathing problems but cannot get out of the vehicle after a[...]

3-38 Seats and Restraints . The vehicle has a crash sensing and diagnostic module which records information after a crash. See V ehicle Data Recording and Privacy on page 13 ‑ 15 and Event Data Recorders on page 13 ‑ 16 . . Let only qualified technicians work on the airbag systems. Improper service can mean that an airbag system will not work properly . See your dealer for service. Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. United States Canada The words ON and OFF , or the symbol for on and off, are visible during the[...]

Seats and Restraints 3-39 We recommend that children be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating[...]

3-40 Seats and Restraints The passenger sensing system is designed to turn on (may inflate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active. For some children, including children in child restraints, and for very small adults, the passenger sensing system may or may not turn off the right front passenger frontal airbag, depending upon the person ’ s seating posture and body build. Everyone in the vehicle who has outgrown child restraints s[...]

Seats and Restraints 3-41 5. If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the vehicle off. Then slightly recline the vehicle seatback and adjust the seat cushion, if adjustable, to make sure that the vehicle seatback is not pushing the child restraint into the seat cushion. Also make sure the child restraint is not trapped under the vehicle head restraint. If this happens, adjust the head restraint. See Head Restraints on page 3 ‑ 2 . 6. Restart the vehicle. The passenger sensing system may or may not turn off the airbag for a child in a child restraint depending upon the child ’ s seating posture and body build. It is better [...]

3-42 Seats and Restraints Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “ Safety Belts ” and “ Child Restraints ” in the Index for additional information about the importance of proper restraint use. A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for [...]

Seats and Restraints 3-43 The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat. If this is not desired remove the object from the seat. { W ARNING Stowing of articles under the passenger seat or between the passenger seat cushion and seatback may interfere with the proper operation of the passenger sensing system. Servicing the Airbag-Equipped V ehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Y our dealer and the service manual have information about servicing the vehicle and the airbag system. T o purchase a serv[...]

3-44 Seats and Restraints Adding Equipment to the Airbag-Equipped V ehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Y es. If you add things that change the vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly . Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module, steering wheel, instrument panel, roof-rail airbag modules, ceiling headliner or pillar garnish trim, overhead console, front sensors, side impact sensors, rollover sensor module, or airbag wiring can affect the operation of the a[...]

Seats and Restraints 3-45 Airbag System Check The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light on page 5 ‑ 14 for more information. Notice: If an airbag covering is damaged, opened, or broken, the airbag may not work properly . Do not open or break the airbag coverings. If there are any opened or broken airbag covers, have the airbag covering and/or airbag module replaced. For the location of the airbag modules, see What Makes an Airbag Inflate? on page 3 ‑ 36 . See your dealer for service. Replacing Airbag System Parts After a Crash { W ARNING A crash can damage the airbag systems [...]

3-46 Seats and Restraints Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle's safety belts. The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster . Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat. . Buckle the lap-shoulder belt. Does the shoulder belt rest on the shoulder? If yes, continue. If no, try using the rear safety belt comfort guide. See “ Rear Safety Belt Comfort Guides ” under Lap-Shoulde[...]

Seats and Restraints 3-47 According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. In a crash, children who are not buckled up can strike other people who are buckled up, or can be thrown out of the vehicle. Older children need to use safety belts properly . { W ARNING Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. { W ARNING Never do this. Never allow a chil[...]

3-48 Seats and Restraints Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle. { W ARNING Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts. Airbags plus lap ‐ shoulder belt[...]

Seats and Restraints 3-49 { W ARNING Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go.[...]

3-50 Seats and Restraints Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. T[...]

Seats and Restraints 3-51 Child Restraint Systems (A) Rear ‐ Facing Infant Seat A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. (B) Forward-Facing Child Seat A forward-facing child seat (B) provides restraint for the child's body with the harness. (C) Booster Seats A booster seat (C) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window .[...]

3-52 Seats and Restraints Securing an Add-On Child Restraint in the V ehicle { W ARNING A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LA TCH system, following the instructions that came with that child restraint and the instructions in this manual. T o help reduce the chance of injury , the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LA TCH system. See Lower Anchors and T ethers for Children (LA TCH Sys[...]

Seats and Restraints 3-53 child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on the sun visor says, “ Never put a rear-facing child restraint in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat i[...]

3-54 Seats and Restraints Lower Anchors and T ethers for Children (LA TCH System) The LA TCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier . The LA TCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LA TCH system. Make sure that a LA TCH-compatible child restraint is properly installed using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual. When installing a child restraint with a top tether , you must also use either the l[...]

Seats and Restraints 3-55 T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash. Y our child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor . Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada[...]

3-56 Seats and Restraints Second Row — 60/40 Bench i (T op T ether Anchor): Seating positions with top tether anchors. j (Lower Anchor): Seating positions with two lower anchors. Third Row i (T op T ether Anchor): Seating positions with top tether anchors. T o assist you in locating the lower anchors, each second row anchor position has a label, near the crease between the seatback and the seat cushion. T o assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover or near the anchor .[...]

Seats and Restraints 3-57 Second Row — Bucket Shown, Bench Similar The top tether anchors are located at the bottom rear of the seatback for each seating position in the second row . Open the cover to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed. Third Row Seat The third row has one top tether anchor located at the bottom rear of the center seatback. This anchor should be used for the center seating position only . Never install two top tethers using the same top tether anchor . Do not secure a child restraint in a position without a top tether anchor if a national or local law requires[...]

3-58 Seats and Restraints Securing a Child Restraint Designed for the LA TCH System { W ARNING If a LA TCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly . In a crash, the child could be seriously injured or killed. Install a LA TCH-type child restraint properly using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual. { W ARNING Do not attach more than one child restraint to a single anchor . Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose[...]

Seats and Restraints 3-59 Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position, before folding the seat. 1. Attach and tighten the lower attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to your child restraint manufacturer instructions and the instructions in this manual. 1.1. Find the lower anchors for the desired seating position. 1.2. Recline the seatback to the full reclined position. Make sure the secon[...]

3-60 Seats and Restraints 2.3. Route, attach and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a single tether , route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a dual tether , route the tether over the seatback. If the position you are using has a fixed headrest or head restraint and you are using a dual tether , route the tether around the headrest or head restraint.[...]

Seats and Restraints 3-61 If the position you are using has a fixed headrest or head restraint and you are using a single tether , route the tether over the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure. Replacing LA TCH System Parts After a Crash { W ARNING A crash can damage the LA TCH system in the vehicle. A damaged LA TCH system may not properly secure the child restraint, resulting in serious injury or even death in a crash. T o help make sure the LA TCH system is working properly after a crash, see your dealer to have the system inspected and any necessary replacements made as soon as possible. If the vehicle has the L[...]

3-62 Seats and Restraints Securing Child Restraints (Rear Seat ) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LA TCH system, see Lower Anchors and T ethers for Children (LA TCH System) on page 3 ‑ 54 for how and where to install the child restraint using LA TCH. If a child restraint is secured in the vehicle using a safety belt and it uses a top tether , see Lower Anchors and T ethers for Children (LA TCH System) on page 3 ‑ 54 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a nati[...]

Seats and Restraints 3-63 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. 6. If the child restraint has a top tether , follow the child restraint manufacturer's instructions regarding the use of the top tether . See Lower Anchors and T ethers for Children (LA TCH System) on page 3 ‑ 54 for more information. 7. Push a[...]

3-64 Seats and Restraints Securing Child Restraints (Right Front Passenger Seat) The vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 3 ‑ 52 . In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions. See Passenger Sensing System on page 3 ‑ 38 and Passenger Airbag Status Indicator on page 5 ‑ 15 for more information, including important safety information. A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if t[...]

Seats and Restraints 3-65 Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether , and that the tether be attached. Y ou will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint. 1. Move the seat as far back as it will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the right front passenger [...]

3-66 Seats and Restraints 6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull the child restraint in different directions to be sure it is secure. If the airbags are off, the of f indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “ If the On Indicator is Lit for a Child[...]

Storage 4-1 Storage Storage Compartments Instrument Panel Storage . . . . 4-1 Glove Box . . . . . . . . . . . . . . . . . . . . 4-1 Cupholders . . . . . . . . . . . . . . . . . . . 4-1 Armrest Storage . . . . . . . . . . . . . . 4-1 Center Console Storage . . . . . . 4-1 Floor Console Storage . . . . . . . . 4-2 Additional Storage Features Cargo Cover . . . . . . . . . . . . . . . . . . 4-3 Cargo T ie Downs . . . . . . . . . . . . . 4-3 Cargo Management System . . . . . . . . . . . . . . . . . . . . . . 4-3 Convenience Net . . . . . . . . . . . . . 4-3 Roof Rack System Roof Rack System . . . . . . . . . . . . 4-4 Storage Compartments Instrument Panel Storage This vehicle has an instrument pa[...]

4-2 Storage open the armrest storage area, press the button located on the front of the armrest. There is additional storage under the armrest. Move the armrest all the way to the rear position, slide the cover back and remove the tray . Floor Console Storage For vehicles with a second row center console, open each area to access the storage compartment inside. T o access the upper storage area, press the upper button (B) and lift up. T o access the lower storage area, press the lower button (C) and lift up. The top of the console can be folded forward for increased storage area. Lift up on handle on the rear of the console (A) and pull forward. { W ARNING Never open more than one of the thr[...]

Storage 4-3 Additional Storage Features Cargo Cover For vehicles with a cargo cover , it can be used to cover items in the rear of the vehicle. T o install the cover , place the loops on each corner of the cover on the four hooks in the rear of the vehicle. The cover should be stored securely when not in use. Cargo Tie Downs Four cargo tie ‐ downs are located in the rear compartment of the vehicle. The tie-downs can be used to secure small loads. Cargo Management System This vehicle has a cargo management system located in the rear of the vehicle. T o remove the cargo management cover: 1. Open the cover . It remains open when lifted. 2. Pull the cover up making sure to unhook the hinges at[...]

4-4 Storage Roof Rack System { W ARNING If something is carried on top of the vehicle that is longer or wider than the roof rack — like paneling, plywood, or a mattress — the wind can catch it while the vehicle is being driven. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle. Never carry something longer or wider than the roof rack on top of the vehicle unless using a GM Certified accessory carrier . For vehicles with a roof rack, the rack can be used to load items. For roof racks that do not have crossrails included, GM Certified crossrails can be purchased as an accessory . See your dealer for additional information. Notice: [...]

Instruments and Controls 5-1 Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls . . . . . . 5-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Windshield Wiper/W asher . . . . . 5-5 Rear Window Wiper/ W asher . . . . . . . . . . . . . . . . . . . . . . 5-6 Compass . . . . . . . . . . . . . . . . . . . . . 5-6 Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Power Outlets . . . . . . . . . . . . . . . . . 5-9 W arning Lights, Gauges, and Indicators W arning Lights, Gauges, and Indicators . . . . . . . . . . . . . . . . . . 5-10 Instrument Cluster . . . . . . . . . . . 5-1 1 Speedometer . . . . . . . . . . . . . . . . 5-12 Odo[...]

5-2 Instruments and Controls V ehicle Personal ization V ehicle Personalization (With DIC Buttons) . . . . . . . . . . . . . . . 5-40 Universal Remote System Universal Remote System . . . 5-47 Universal Remote System Programming . . . . . . . . . . . . . . . 5-47 Universal Remote System Operation . . . . . . . . . . . . . . . . . . 5-51 Controls Steering Wheel Adjustment The steering wheel can be adjusted. The adjustment lever is on the outboard side of the steering column. Pull the lever down to move the steering wheel up or down and in or out. Pull the lever up to lock the steering wheel in place. Do not adjust the steering wheel while driving. Power Tilt Wheel For vehicles with the power [...]

Instruments and Controls 5-3 Push the control forward or rearward to move the steering wheel toward the front or rear of the vehicle. T o set the memory position, see V ehicle Personalization (With DIC Buttons) on page 5 ‑ 40 . Steering Wheel Controls V ehicles with audio steering wheel controls could differ depending on the vehicle's options. Some audio controls can be adjusted at the steering wheel. w / x (Next / Previous): Press to select preset or favorite radio stations, select tracks on a CD/DVD, or to select tracks and navigate folders on an iPod ® or USB device. T o select preset or favorite radio stations: . Press and release w or x to go to the next or previous radio statio[...]

5-4 Instruments and Controls T o navigate folders on an iPod or USB device for vehicles without a navigation system: 1. Press and hold w or x while listening to a song until the contents of the current folder display on the radio display . 2. Press and hold x to go back to the previous folder list. 3. Press and release w or x to scroll up or down the list. . T o select a folder , press and hold w , or press ¨ when the folder is highlighted. . T o go back further in the folder list, press and hold x . T o navigate folders on an iPod or USB device for vehicles with a navigation system: 1. Go to the Music Navigator by first touching the center touch screen folder button in the main audio page.[...]

Instruments and Controls 5-5 Press ¨ to select a track or a folder when navigating folders on an iPod or USB device. For vehicles with a navigation system: 1. Press and hold ¨ until a beep is heard, to place the radio into SCAN mode, a station will play for five seconds before moving to the next station. 2. T o stop the SCAN function, press ¨ again. 3. In CD/DVD, iPod, or AUX USB, press and hold to quickly move forward through the tracks. Release to stop on the desired track. + e − e (V olume): Press to increase or to decrease the volume. Horn Press near the horn symbols or press on the steering wheel pad to sound the horn. Windshield Wiper/W asher The windshield wiper/washer lever is l[...]

5-6 Instruments and Controls Windshield W asher J (W asher Fluid): Press the button at the end of the turn signal/ lane change lever , to spray washer fluid on the windshield. The wipers clear the windshield and either stop or return to the preset speed. The ignition key must be in ACC/ ACCESSORY or ON/RUN for this to work. See Washer Fluid on page 10 ‑ 21 Windshield W asher Fluid . { W ARNING In freezing weather , do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. W ASHER FLUID LOW ADD FLUID is displayed on the Driver Information Center (DIC) when the washer fluid is low . See Washer Fluid Messages on pag[...]

Instruments and Controls 5-7 Compass variance is the difference between the earth's magnetic north and true geographic north. If the compass is not set to the zone where you live, the compass may give false readings. The compass must be set to the variance zone in which the vehicle is traveling. T o adjust for compass variance, use the following procedure: Compass V ariance (Zone) Procedure 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in P (Park). Press the vehicle information button until PRESS V TO CHANGE COMP ASS ZONE displays. 2. Find the vehicle's current location and variance zone number on the map. Zones 1 through 15 are availabl[...]

5-8 Instruments and Controls If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic CB or cell phone antenna mount, a magnetic emergency light, magnetic note pad holder , or any other magnetic item. T urn off the vehicle, move the magnetic item, then turn on the vehicle and calibrate the compass. T o calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, make sure the compass zone is set to the variance zone in which the vehicle is located. See “ Compas[...]

Instruments and Controls 5-9 5. T o decrease the time or date, do one of the following: . Press © SEEK. . Press s REV . . T urn f counter ‐ clockwise. T o change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1. Press G and then the pushbutton located under the forward arrow that displays on the radio screen until the time 12H (hour) and 24H (hour), and the date MM/DD (month and day) and DD/MM (day and month) displays. 2. Press the pushbutton located under the desired option. 3. Press G again to apply the selected default, or let the screen time out. Power Outlets Accessory power outlets can be used to plug in [...]

5-10 Instruments and Controls Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should. The repairs would not be covered by the vehicle warranty . Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by the vehicle warranty . Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only . W arning Li[...]

Instruments and Controls 5-1 1 Instrument Cluster United States Uplevel version shown, Canada similar[...]

5-12 Instruments and Controls Speedometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper-resistant odometer . If the vehicle needs a new odometer installed, the new one is set to the mileage of the old odometer . If this is not possible, it is set at zero and a label is put on the driver's door to show the old mileage reading. T achometer The tachometer displays the engine speed in revolutions per minute (rpm). Fuel Gauge United States Canada When the ignition is on, the fuel gauge indicates about how much [...]

Instruments and Controls 5-13 conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible. See Engine Overheating on page 10 ‑ 18 for more information. V oltmeter Gauge When the engine is not running, but the ignition is on, this gauge displays the battery voltage in DC volts. When the engine is running, the gauge shows the condition of the charging system. The gauge can transition from a higher to lower or a lower to higher reading. This is normal. Readings between the low and high warning zones indicate the normal operating range. The voltmeter gauge can also read lower when in fuel economy mode. This is normal. Readings in the low warning zone can occur [...]

5-14 Instruments and Controls Passenger Safety Belt Reminder Light When the engine is started this light and the chime come on and stay on for several seconds to remind the passenger to fasten their safety belt. The light also begins to flash. This only occurs if the passenger airbag is enabled. See Passenger Sensing System on page 3 ‑ 38 for more information. This cycle repeats if the passenger remains unbuckled and the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop or other electronic d[...]

Instruments and Controls 5-15 Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3 ‑ 38 for important safety information. The instrument panel has a passenger airbag status indicator . United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF , or the symbol for on and off, for several seconds as a system check. If you are using remote start to start the vehicle from a distance, if equipped, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF , or either the on or off symbol to let you know the status of the rig[...]

5-16 Instruments and Controls Charging System Light The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer . Driving while this light is on could drain the battery . When this light comes on, the Driver Information Center (DIC) also displays the SERVICE BA TTERY CHARGING SYSTEM message. See V ehicle Messages on page 5 ‑ 31 for more information. If a short distance must be driven with the light on, be sure to turn off[...]

Instruments and Controls 5-17 Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty . This could also result in a failure to pass a required Emission Inspection/ Maintenance test. See Accessories and Modifications on page 10 ‑ 3 . This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire incr[...]

5-18 Instruments and Controls . Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and may cause: stalling after start-up, stalling when the vehicle is changed into gear , misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9 ‑ 40 . If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and dia[...]

Instruments and Controls 5-19 United States Canada This light should come on briefly when the ignition key is turned to ON/RUN. If it does not come on then, have it fixed so it will be ready to warn if there is a problem. This light may also come on due to low brake fluid. See Brakes on page 10 ‑ 22 for more information. When the ignition is on, the brake system warning light will also come on when the parking brake is set. The light will stay on if the parking brake does not release fully . If it stays on after the parking brake is fully released, it means there is a brake problem. If the light comes on while driving, pull off the road and stop carefully . Make sure the parking brake is f[...]

5-20 Instruments and Controls Then start the engine again to reset the system. If the light still stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, there are still brakes, but no antilock brakes. If the regular brake system warning light is also on, there are no antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5 ‑ 18 . T ow/Haul Mode Light This light comes on when the T ow/ Haul mode has been activated. For more information, see T ow/Haul Mode on page 9 ‑ 26 . StabiliT rak ® Indicator Light This light comes on briefly while starting the engine. If it does not, h[...]

Instruments and Controls 5-21 Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the T ire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See Tire Messages on page 5 ‑ 37 for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the tire loading information label. See Tire Pressure on page 10 ‑ 42 for more information. When the Light Flashes First [...]

5-22 Instruments and Controls Security Light This light flashes when the security system is activated. For more information, see Anti-Theft Alarm System on page 2 ‑ 13 . High-Beam on Light The high-beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6 ‑ 2 for more information. Cruise Control Light This light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 9 ‑ 31 for more information. Information Displays Driver Information Center (DIC) (With DIC Buttons) If your vehicle has DIC buttons, the information below explains the operation of this system. The [...]

Instruments and Controls 5-23 The outside air temperature and compass, if equipped, also display on the DIC when viewing the trip and fuel information. The outside air temperature automatically appears in the top right corner of the DIC display . If there is a problem with the system that controls the temperature display , the numbers will be replaced with dashes. If this occurs, have the vehicle serviced. The compass will be shown in the bottom right corner of the DIC display . See Compass on page 5 ‑ 6 for more information. The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel. The DIC also allows some features to be customized. [...]

5-24 Instruments and Controls will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display . See “ CHANGE ENGINE OIL SOON ” under Engine Oil Messages on page 5 ‑ 34 . Y ou should change the oil as soon as you can. See Engine Oil on page 10 ‑ 8 . In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 1 1 ‑ 2 for more information. Remember , you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. A[...]

Instruments and Controls 5-25 in the display . See Tire Pressure on page 10 ‑ 42 and Tire Messages on page 5 ‑ 37 for more information. If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer for service. RELEARN REMOTE KEY This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. T o match an RKE transmitter to your vehicle: 1. Press the vehicle information button until PRESS V TO RELEARN REMOTE KEY displays. 2. Press the set/reset button un[...]

5-26 Instruments and Controls TRIP A and TRIP B Press the trip/fuel button until TRIP A or TRIP B displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for each trip odometer . Both trip odometers can be used at the same time. Pressing the trip odometer reset stem will also display the trip odometers. Each trip odometer can be reset to zero separately by pressing the set/ reset button or the trip odometer reset stem while the desired trip odometer is displayed. The trip odometer has a feature called retroactive reset. This can be used to set the trip odometer to the number of miles (kilometers) driven since the ignition was la[...]

Instruments and Controls 5-27 A VG (Average) ECONOMY Press the trip/fuel button until A VG ECONOMY displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset. T o reset A VG ECONOMY , press and hold the set/ reset button. Fuel Economy Press the trip/fuel button until FUEL ECONOMY displays. The FUEL ECONOMY display shows an estimate of the vehicle fuel economy under a given driving condition at a specific moment. For example, if the vehicle is accelerating and achieving low fuel efficiency this display will show fewer b[...]

5-28 Instruments and Controls Driver Information Center (DIC) (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster . Pressing the trip odometer reset stem will also turn off, or acknowledge, DIC messages. The DIC displays trip and vehicle system information, and warning messages if a system problem is detected. If your vehicle does not have DIC buttons, you can use the trip odometer reset stem to view the following displays: odometer , trip odometers, oil life, park assist menu for vehicl[...]

Instruments and Controls 5-29 driven 5 miles (8 km) before it is started again, and then the retro-active reset feature is activated, the display will show 5 miles (8 km). As the vehicle begins moving, the display will then increase to 5.1 miles (8.2 km), 5.2 miles (8.4 km), etc. If the retro-active reset feature is activated after the vehicle is started, but before it begins moving, the display will show the number of miles (mi) or kilometers (km) that were driven during the last ignition cycle. OIL LIFE T o access this display , the vehicle must be in P (Park). Press the trip odometer reset stem until OIL LIFE REMAINING displays. This display shows an estimate of the oil's remaining u[...]

5-30 Instruments and Controls RELEARN REMOTE KEY T o access this display , the vehicle must be in P (Park). This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. T o match an RKE transmitter to your vehicle: 1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays. 2. Press and hold the trip odometer reset stem until REMOTE KEY LEARNING ACTIVE is displayed. 3. Press and hold the lock and unlock buttons on the first transmitter at the same time for about 15 seconds. On vehicles with memory recall seats, the first transm[...]

Instruments and Controls 5-31 V ehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another . Some messages may not require immediate action, but you can press any of the DIC buttons on the instrument panel or the trip odometer reset stem on the instrument panel cluster to acknowledge that you received the messages and to clear them from the display . Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. Y ou should take any messages[...]

5-32 Instruments and Controls Brake System Messages SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 5 ‑ 18 . If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display . If the message is still displayed or appears again when you begin driving, the brake system needs service as soon as possible. See your dealer . Cruise Control Messages CRUISE SET TO XXX This message displays whenever the cruise control is set. See Cruise Control on page 9 ‑ 31 for more information. Door Ajar Messages DRI[...]

Instruments and Controls 5-33 RIGHT REAR DOOR OPEN This message displays and a chime sounds if the passenger side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. Engine Cooling System Messages ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant T emperature Gauge on page 5 ‑ 12 . T o avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to norma[...]

5-34 Instruments and Controls Engine Oil Messages CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System on page 10 ‑ 10 for information on how to reset the message. See Engine Oil on page 10 ‑ 8 and Scheduled Maintenance on page 1 1 ‑ 2 for more information. OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low , severe engine damage may occur . If a low oil pressure warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not drive the vehicle until the c[...]

Instruments and Controls 5-35 TIGHTEN GAS CAP This message may display along with the check engine light on the instrument panel cluster if the vehicle's fuel cap is not tightened properly . See Malfunction Indicator Lamp on page 5 ‑ 16 . Reinstall the fuel cap fully . See Filling the T ank on page 9 ‑ 42 . The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off. Key and Lock Messages REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE[...]

5-36 Instruments and Controls odometer reset stem to acknowledge this message and clear it from the DIC display . For more information see Ultrasonic Parking Assist on page 9 ‑ 33 . SERVICE P ARK ASSIST If your vehicle has the Ultrasonic Rear Parking Assist (URP A) system, this message displays if there is a problem with the URP A system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9 ‑ 33 for more information. See your dealer for service. Ride Control System Messages SERVICE ST ABILITRAK This message displays if there is a problem with the StabiliTrak ® system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 [...]

Instruments and Controls 5-37 THEFT A TTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Anti-Theft Alarm System on page 2 ‑ 13 for more information. Service V ehicle Messages SERVICE A/C (Air Conditioning) SYSTEM This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer if you notice a drop in heating and air conditioning efficiency . SERVICE POWER STEERING This message displays when a problem is detected with the power steering system. When this message is displayed, you ma[...]

5-38 Instruments and Controls Y ou can receive more than one tire pressure message at a time. T o read the other messages that may have been sent at the same time, press the set/reset button or the trip odometer reset stem. The DIC also shows the tire pressure values. See Driver Information Center (DIC) (With DIC Buttons) on page 5 ‑ 22 or Driver Information Center (DIC) (Without DIC Buttons) on page 5 ‑ 28 . SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly . The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5 ‑ [...]

Instruments and Controls 5-39 appears again when you begin driving, the AWD system needs service. See your dealer . SERVICE TRANSMISSION This message displays when there is a problem with the transmission. See your dealer for service. TRANSMISSION HOT IDLE ENGINE Notice: If you drive your vehicle while the transmission fluid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty . Do not drive your vehicle with overheated transmission fluid or while the transmission temperature warning is displayed. This message displays and a[...]

5-40 Instruments and Controls V ehicle Personalization V ehicle Personalization (With DIC Buttons) Y our vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. All of the customization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the customization features were set when your vehicle left the factory , but may have been changed from their default state since then. The customization preferences are automati[...]

Instruments and Controls 5-41 Press the customization button until the DISPLA Y LANGUAGE screen appears on the DIC display . Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: ENGLISH (default): All messages will appear in English. FRANCAIS: All messages will appear in French. ESP ANOL: All messages will appear in Spanish. NO CHANGE: No change will be made to this feature. The current setting will remain. T o select a setting, press the set/ reset button while the desired setting is displayed on the DIC. Y ou can also change the language by pressing the trip odometer reset stem. See “ Langua[...]

5-42 Instruments and Controls DRIVER IN P ARK: Only the driver's door will unlock when the vehicle is shifted into P (Park) . ALL A T KEY OUT : All of the doors will unlock when the key is taken out of the ignition. ALL IN P ARK (default): All of the doors will unlock when the vehicle is shifted into P (Park). NO CHANGE: No change will be made to this feature. The current setting will remain. T o select a setting, press the set/ reset button while the desired setting is displayed on the DIC. REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter . Y ou will not receive feedback whe[...]

Instruments and Controls 5-43 LIGHTS ON (default): The exterior lamps will flash when you press the unlock button on the RKE transmitter . NO CHANGE: No change will be made to this feature. The current setting will remain. T o select a setting, press the set/ reset button while the desired setting is displayed on the DIC. DELA Y DOOR LOCK This feature allows you to select whether or not the locking of the vehicle's doors and liftgate will be delayed. When locking the doors and liftgate with the power door lock switch and a door or the liftgate is open, this feature will delay locking the doors and liftgate until five seconds after the last door is closed. Y ou will hear three chimes to [...]

5-44 Instruments and Controls APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter . Press the customization button until APPROACH LIGHTING appears on the DIC display . Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The exterior lights will not turn on when you unlock the vehicle with the RKE transmitter . ON (default): If it is dark enough outside, the exterior lights will turn on briefly when you unlock the vehicle with the R[...]

Instruments and Controls 5-45 Press the customization button until P ARK TIL T MIRRORS appears on the DIC display . Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): Neither outside mirror will be tilted down when the vehicle is shifted into R (Reverse). DRIVER MIRROR: The driver's outside mirror will be tilted down when the vehicle is shifted into R (Reverse). P ASSENGER MIRROR: The passenger's outside mirror will be tilted down when the vehicle is shifted into R (Reverse). BOTH MIRRORS: The driver's and passenger's outside mirrors will be tilted down when [...]

5-46 Instruments and Controls Press the customization button until MEMORY SEA T RECALL appears on the DIC display . Press the set/ reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No remote memory seat recall will occur . ON: The driver's seat and outside mirrors will automatically move to the stored driving position when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed. See “ Relearn Remote Key ” under Driver Information Center (DIC) (With DIC Buttons) on page 5 ‑ 22 or Driver Information Center (DIC) (Without DIC Buttons) on page 5 ‑ 28 for more info[...]

Instruments and Controls 5-47 T o select a setting, press the set/ reset button while the desired setting is displayed on the DIC. EXIT FEA TURE SETTINGS This feature allows you to exit the feature settings menu. Press the customization button until FEA TURE SETTINGS PRESS V TO EXIT appears in the DIC display . Press the set/reset button once to exit the menu. If you do not exit, pressing the customization button again will return you to the beginning of the feature settings menu. Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: . The vehicle is shifted out of P (Park). . The vehicle is no longer in ON/RUN. . The trip/fuel or vehicl[...]

5-48 Instruments and Controls Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you with programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for se[...]

Instruments and Controls 5-49 2. Hold the end of your hand-held transmitter about 3 to 8 cm (1 to 3 inches) away from the Universal Home Remote buttons while keeping the indicator light in view . The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require substitution of Step 3 with the procedure noted in “ Gate Operator a[...]

5-50 Instruments and Controls 7. Firmly press and release the “ Learn ” or “ Smart ” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, selected in Step 3 to control the garage door , for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door . T o program the remaining two Universal Home Remote[...]

Instruments and Controls 5-51 Universal Remote System Operation Using Universal Remote Press and hold the appropriate Universal Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. T o erase all programmed buttons on the Universal Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds. 2. Release both buttons. Reprogramming a Single Universal Remote Button T o reprogram any of the three Universal Remote buttons, repeat the programming instructions [...]

5-52 Instruments and Controls 2 NOTES[...]

Lighting 6-1 Lighting Exterior Lighting Exterior Lamp Controls . . . . . . . . 6-1 Headlamp High/Low-Beam Changer . . . . . . . . . . . . . . . . . . . . . 6-2 Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2 Daytime Running Lamps (DRL)/Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 6-3 Delayed Headlamps . . . . . . . . . . 6-3 Hazard W arning Flashers . . . . . 6-3 T urn and Lane-Change Signals . . . . . . . . . . . . . . . . . . . . . . 6-4 Interior Lighting Instrument Panel Illumination Control . . . . . . . . . . . . . . . . . . . . . . 6-4 Courtesy Lamps . . . . . . . . . . . . . . 6-4 Dome Lamps . . . . . . . . . . . . . . . . . 6-5 Reading Lamps . . . . . . .[...]

6-2 Lighting The exterior lamps control has four positions: 9 (Off): Briefly turn to this position to turn the automatic light control off or on again. AUTO (Automatic): Turns the headlamps on automatically at normal brightness, together with the following: . Parking Lamps . T aillamps . License Plate Lamps . Instrument Panel Lights ; (Parking Lamps): Turns the parking lamps on together with the following: . T aillamps . License Plate Lamps . Instrument Panel Lights 2 (Headlamps): T urns the headlamps on together with the following lamps listed below . A warning chime sounds if the driver's door is opened when the ignition switch is off and the headlamps are on. . Parking Lamps . T aill[...]

Lighting 6-3 Daytime Running Lamps (DRL)/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day . Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met: . The ignition is in the ON/RUN position. . The exterior lamps control is in AUTO. . The engine is running. When the DRL are on, the regular headlamps, taillamps, sidemarker , and other lamps will not be on. The instrument panel and cluster will also not be lit. The headlamps automatically change from DRL to the regula[...]

6-4 Lighting T urn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times. The lever returns to its starting position whenever it is released. If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb might be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breaker[...]

Lighting 6-5 The reading lamps, located on the headliner above the rearview mirror , can be turned on or off independent of the automatic courtesy lamps, when the doors are closed. Dome Lamps The dome lamps are located in the overhead console and above the rear seat passengers. The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. The lamps can also be turned on and off by turning the instrument panel brightness control clockwise to the farthest position. Dome Lamp Override The dome lamp override button is next to the exterior lamps control. E (Dome Lamp Override): Press the button in and the dome lamps remain off when a door is opene[...]

6-6 Lighting When the ignition is on, illuminated entry is inactive, which means the courtesy lamps will not come on unless a door is opened. Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature continues to work until one of the following occurs: . The ignition is in ON/RUN. . The doors are locked. . An illumination period of about 25 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period is canceled and the interior lamps r[...]

Lighting 6-7 voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger , climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery . It does[...]

6-8 Lighting 2 NOTES[...]

Infotainment System 7-1 Infotainment System Introduction Introduction . . . . . . . . . . . . . . . . . . . 7-1 Theft-Deterrent Feature . . . . . . . 7-2 Operation . . . . . . . . . . . . . . . . . . . . . 7-2 Radio AM-FM Radio . . . . . . . . . . . . . . . . . 7-6 Satellite Radio . . . . . . . . . . . . . . . . 7-8 Radio Reception . . . . . . . . . . . . . 7-1 1 Multi-Band Antenna . . . . . . . . . . 7-12 Audio Players CD Player . . . . . . . . . . . . . . . . . . . 7-12 CD/DVD Player . . . . . . . . . . . . . . 7-14 MP3 (Radio with CD and Radio with CD/USB) . . . . . . . 7-21 MP3 (Radio with CD/DVD) . . . 7-27 Auxiliary Devices . . . . . . . . . . . . 7-33 Rear Seat Infotainment Rear Seat [...]

7-2 Infotainment System For more information, see Defensive Driving on page 9 ‑ 2 . The vehicle has Retained Accessory Power (RAP). With RAP , the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 9 ‑ 17 for more information. Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Theft-Deterrent Feature THEFTLOCK ® is designed to discourage theft of the vehicle's radio by learning a portion of the V ehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle. Operation Radio with CD, Radio with CD/USB similar[...]

Infotainment System 7-3 Radio with CD, DVD, and USB The vehicle may have one of these radios as its audio system. Radios with CD, DVD, and USB Radios with CD, DVD, and USB have a Bose ® Surround Sound System. Some of its features are explained later in this section under , “ Adjusting the Speakers (Balance/Fade) ” . If the vehicle has a Rear Seat Entertainment (RSE) system, it has a CD, DVD, and USB radio. See Rear Seat Entertainment (RSE) System on page 7 ‑ 35 for more information on the vehicle's RSE system. The DVD player is the top slot on the radio faceplate. The player is capable of reading the DTS programmed DVD Audio or DVD Video media. DTS and DTS Digital Surround are re[...]

7-4 Infotainment System prevents the rear seat occupant from operating the Rear Seat Audio (RSA) system or remote control. A lock symbol displays next to the clock display while the parental control feature is being used. The feature remains on until O is pressed and held for more than two seconds, or the driver turns the ignition off and exits the vehicle. 4 (Information): Press to switch the display between the radio station frequency and the time. When the ignition is in the OFF position, press 4 to display the time. For vehicles with XM, MP3, WMA or RDS features, press 4 to display additional text information related to the current FM-RDS or XM station; or CD, MP3 or WMA song. If informa[...]

Infotainment System 7-5 Setting the T one (Bass/ Midrange/T reble) BASS/MID/TREB (Bass, Midrange, or T reble): T o adjust bass, midrange, or treble: 1. Press f until the tone control tabs display . 2. Continue pressing f to highlight the tab, or press the softkey under the tab. 3. T o adjust the highlighted setting, do one of the following until the levels are obtained. . T urn f clockwise or counterclockwise. . Press FWD, or s REV . If a station's frequency is weak or if there is static, decrease the treble. T o quickly adjust bass, midrange, or treble to the middle position, press the softkey under the BASS, MID, or TREB tab for more than two seconds. A beep sounds and the level adj[...]

7-6 Infotainment System T o quickly adjust all speaker and tone controls to the middle position, press f for more than two seconds until a beep sounds. Radios with CD and DVD fade differently depending on the DVD Media type: . With DVD ‐ A 5.1 Surround media, the left front and right front speakers fade rearward, leaving the center front speakers unaffected until the last fade step, then all front speakers mute. . With DVD ‐ V 5.1 Surround media, surround sound is maintained until Step 4 of the Fade control is reached while fading rearward. At that point the audio system output changes to Stereo to prevent the loss of Center channel output when the full rearward fade position is reached.[...]

Infotainment System 7-7 © SEEK ¨ : Press to go to the previous or to the next station and stay there. T o scan stations, press and hold © or ¨ until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. The radio only seeks and scans stations with a strong signal that are in the selected band. Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is in P (Park). Tune to favorite stations using the presets, favorites button, and steering wheel controls. See Steering Wheel Controls on page 5 ‑ 3 . F A V (Favorites): A maximum of 36 stat[...]

7-8 Infotainment System Satellite Radio XM ™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. For more information, contact XM at www .xmradio.com or call 1-800-929-2100 in the U.S. and www .xmradio.ca or call 1-877-438-9677 in Canada. Finding a Station BAND: Press to switch between AM, FM, or XM. The selection displays. f (T une): Turn to select radio stations. © SEEK ¨ : Press to go to the previous or to the next station and stay there. T o scan stations, press and hold © or ¨ u[...]

Infotainment System 7-9 Undesired XM categories can be removed through the setup menu. T o remove an undesired category , perform the following: 1. Press MENU to display the radio setup menu. 2. Press the softkey below the XM CA T tab. 3. T urn f to display the category to be removed. 4. Press the softkey under the Remove tab until the category name along with the word Removed displays. 5. Repeat the steps to remove more categories. Removed categories can be restored by pressing the softkey under the Add tab when a removed category is displayed or by pressing the softkey under the Restore All tab. Categories cannot be removed or added while the vehicle is moving faster than 8 km/h (5 mph). S[...]

7-10 Infotainment System 4. Press F A V , or let the menu time out, to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages. XM ™ Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer's request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal: The system is functioning correctly , but the vehicle is in a location that is blocking the XM ™ signal. When the vehicle is move[...]

Infotainment System 7-1 1 Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer . Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer . XM Not A vailable: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer . Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or stati[...]

7-12 Infotainment System Multi-Band Antenna The multi-band antenna is located on the roof of the vehicle. This type of antenna is used with the AM/FM radio, as well as OnStar ® and the XM ™ Satellite Radio Service System, if the vehicle has these features. Keep this antenna clear of snow and ice build up for clear radio reception. If the vehicle has a sunroof, the performance of the radio system may be affected if the sunroof is open. Loading items onto the roof of the vehicle can interfere with the performance of the radio system and, if the vehicle has this feature, OnStar ® . Make sure the multi-band antenna is not obstructed. Audio Players CD Player Playing a CD Insert a CD partway i[...]

Infotainment System 7-13 BAND: Press to listen to the radio when a CD is playing. The CD remains inside the radio for future listening. CD/AUX (CD/Auxiliary): Press to select between CD, or Auxiliary . . When a CD is in the player the CD icon and a message showing the disc and/or track number displays. . If an auxiliary input device is not connected, “ No Input Device Found ” displays. Care of CDs If playing a CD-R, the sound quality can be reduced due to CD-R or CD-RW quality , the method of recording, the quality of the music that has been recorded, and the way the CD-R or CD-RW has been handled. Handle them carefully . Store CD-R(s) or CD-RW(s) in their original cases or other protect[...]

7-14 Infotainment System CD Messages CHECK DISC: Radios with a Single CD player display CHECK DISC and/or ejects the CD if an error occurs. Optical Error: The disc was inserted upside down. Disk Read Error: A disc was inserted with an invalid or unknown format. Player Error: There are disc LOAD or disc EJECT problems. . It is very hot. When the temperature returns to normal, the CD should play . . The road is very rough. When the road becomes smoother , the CD should play . . The CD is dirty , scratched, wet, or upside down. . The air is very humid. If so, wait about an hour and try again. . There could have been a problem while burning the CD. . The label could be caught in the CD player . [...]

Infotainment System 7-15 If the disc is not removed, after several seconds, the disc automatically pulls back into the player . Z DVD (Eject): Press and release to eject the disc that is currently playing in the top slot. A beep sounds and Ejecting Disc displays. If loading and reading of a disc cannot be completed, and the disc fails to eject, press and hold Z DVD for more than five seconds to force the disc to eject. f (T une): Turn to select tracks on the CD that is currently playing. © SEEK ¨ : Press © to go to the start of the current track if the track has played more than five seconds. If the track has played less than five seconds the previous track will play . Press ¨ to go to t[...]

7-16 Infotainment System If a disc is inserted into the top DVD slot, the rear seat operator can turn on the video screen and use the remote control to only navigate the CD tracks through the remote control. See “ Using the Auxiliary Input Jack(s) ” later in this section, or “ Audio/Video (A/V) Jacks ” under , Rear Seat Entertainment (RSE) System on page 7 ‑ 35 for more information. Care of CDs and DVDs If playing a CD-R, the sound quality can be reduced due to CD-R or CD-RW quality , the method of recording, the quality of the music that has been recorded, and the way the CD-R or CD-RW has been handled. Handle them carefully . Store CD-R(s) or CD-RW(s) in their original cases or o[...]

Infotainment System 7-17 Front seat passengers can listen to the radio (AM, FM, or XM) by pressing BAND or DVD/CD AUX to select the CD slot, DVD slot, front or rear auxiliary input (if available). If a playback device is plugged into the radio ’ s front auxiliary input jack or the rear auxiliary jack, the front seat passengers are able to listen to playback from this source through the vehicle speakers. See “ Using the Auxiliary Input Jack(s) ” later in this section, or “ Audio/Video (A/V) Jacks ” under , Rear Seat Entertainment (RSE) System on page 7 ‑ 35 for more information. In some vehicles, depending on audio options, the rear speakers can be muted when the RSA power is turn[...]

7-18 Infotainment System Using the DVD Player The DVD player can be controlled by the buttons on the remote control, the RSA system, or by the buttons on the radio faceplate. See “ Remote Control ” , under Rear Seat Entertainment (RSE) System on page 7 ‑ 35 and Rear Seat Audio (RSA) System on page 7 ‑ 43 for more information. The DVD player is only compatible with DVDs of the appropriate region code that is printed on the jacket of most DVDs. The DVD slot of the radio is compatible with most audio CDs, CD-R, CD-RW , DVD-Video, DVD-Audio, DVD-R/RW , DVD+R/ RW media along with MP3 and WMA formats. If an error message displays on the video screen or the radio, see “ DVD Display Error [...]

Infotainment System 7-19 fails to eject, press and hold for more than five seconds to force the disc to eject. DVD-V (Video) Display Buttons Once a DVD-V is inserted, the radio display menu shows several icons. Press the softkeys under any icon during DVD playback. See the icon list below for more information. The rear seat passenger can navigate the DVD-V menus and controls through the remote control. See “ Remote Control ” , under Rear Seat Entertainment (RSE) System on page 7 ‑ 35 for more information. The Video Screen automatically turns on when the DVD-V is inserted into the DVD slot. r / j (Play/Pause): Press either the play or pause icon displayed on the radio system, to toggle [...]

7-20 Infotainment System It must be manually turned on by the rear seat occupant through the remote control power button. r / j (Play/Pause): Press either the play or pause icon displayed on the radio system, to toggle between pausing or restarting playback of a DVD. . If the forward arrow is showing on display , the system is in pause mode. . If the pause icon is showing on display , the system is in playback mode. q Group r : Press to cycle through musical groupings on the DVD-A disc. Nav (Navigate): Press to display directional arrows for navigating through the menus. e (Audio Stream): Press to cycle through audio stream formats located on the DVD-A disc. The video screen shows the audio [...]

Infotainment System 7-21 has been ejected or the stop button has been pressed twice on the remote control, the disc resumes playing at the beginning of the disc. Ejecting a Disc Press Z DVD on the radio to eject the disc. If a disc is ejected from the radio, but not removed, the radio reloads the disc after a short period of time. The disc is stored in the radio. The radio does not resume play of the disc automatically . If the movie is reloaded and the RSA system is sourced to the DVD, the player begins to play again. If loading and reading a DVD or CD cannot be completed, and the disc fails to eject, press and hold Z DVD for more than five seconds to force the disc to eject. DVD Error Mess[...]

7-22 Infotainment System . Playlists with an .m3u or .wpl extension. . Files with an .mp3, .wma, or .cda file extension. USB Supported File and Folder Structure The radio supports: . Up to 700 folders. . Up to 8 folders in depth. . Up to 65,535 files. . Folder and file names up to 64 bytes. . Files with an .mp3 or .wma file extension. . AAC files stored on an iPod. . F A T16 . F A T32 Root Directory The root directory of the disc is treated as a folder . If the root directory has compressed audio files, the directory displays on the radio as the CD label. If a disc contains both uncompressed CD audio and MP3/ WMA files, a folder under the root directory called CD accesses all of the CD audio[...]

Infotainment System 7-23 File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. T rack names longer than 32 characters or four pages are shortened. Parts of words on the last page of text and the extension of the filename does not display . Preprogrammed Playlists Preprogrammed playlists that were created using WinAmp ™ , MusicMatch ™ , or Real Jukebox ™ software can be accessed, however , they cannot be edited using the radio. These playlists are treated as special folders containing compressed audi[...]

7-24 Infotainment System When the scan is finished, the disc begins playing files in order by artist. The current artist playing is shown on the second line of the display . Once all songs by that artist are played, the player moves to the next artist in alphabetical order and begins playing files by that artist. T o listen to files by another artist, press the softkey located below either arrow tab. The disc goes to the next or previous artist in alphabetical order . Continue pressing either softkey below the arrow tab until the artist displays. T o change from playback by artist to playback by album: 1. Press the softkey located below the Sort By tab. 2. Press one of the softkeys below the[...]

Infotainment System 7-25 Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio ’ s display . f (T une): Turn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played. Press and hold or press multiple times to continue moving backward through tracks. ¨ SEEK: Press to go to the next track. Press and hold or press multiple times to continue moving forward through tracks. s REV (Reverse): Press and hold to reverse playback quickly . Sound is heard at a reduced volume. Release s REV to resume playing. The elapsed time o[...]

7-26 Infotainment System 4. T urn f to scroll through the files in the selected folder . 5. Press f to select the file to be played. T o skip through large lists, the five softkeys can be used to navigate in the following order: . First softkey , first item in the list. . Second softkey , 1% through the list each time the softkey is pressed. . Third softkey , 5% through the list each time the softkey is pressed. . Fourth softkey , 10% through the list each time the softkey is pressed. . Fifth softkey , end of the list. h (Music Navigator): Press the softkey below h to view and select a file on an iPod, using the iPod's menu system. Files are sorted by: . Playlists . Artists . Albums . G[...]

Infotainment System 7-27 ' (Repeat T rack): Press the softkey below ' to repeat one track. The tab appears raised when Repeat T rack is being used. Shuffle Functionality T o use Shuffle: Press the softkey below > , 2 , < or = to select between Shuffle Off, Shuffle All Songs/ Shuffle Songs, Shuffle Album, or Shuffle Folder . > (Shuffle Off): This is the default mode when a USB storage device or iPod is first connected. 2 (Shuffle All Songs / Shuffle Songs): Shuffles all songs on the USB storage device or iPod. < (Shuffle Album): Shuffles all songs in the current album on an iPod. = (Shuffle Folder): Shuffles all songs in the current folder on a USB storage device. MP3 (R[...]

7-28 Infotainment System USB Supported File and Folder Structure The radio supports: . Up to 700 folders. . Up to 8 folders in depth. . Up to 65,535 files. . Folder and file names up to 64 bytes. . Files with an .mp3 or .wma file extension. . AAC files stored on an iPod. . F A T16 . F A T32 Root Directory The root directory of the disc is treated as a folder . If the root directory has compressed audio files, the directory displays as F1 ROOT on the radio. If a disc contains both uncompressed CD audio and MP3/ WMA files, a folder under the root directory called CD accesses all of the CD audio tracks on the disc. Empty Folder Folders that do not contain files are skipped, and the player advan[...]

Infotainment System 7-29 . Play begins from the first track in the first folder and continues sequentially through all tracks in each folder . When the last track of the last folder has played, play continues from the first track of the first folder . When play enters a new folder , the display does not automatically show the new folder name unless the folder mode has been chosen as the default display . The new track name displays. File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. T rack names longer[...]

7-30 Infotainment System S c (Previous Folder): Press the softkey below S c to go to the first track in the previous folder . c T (Next Folder): Press the softkey below c T to go to the first track in the next folder . RDM (Random): Files on the disc can be listened to in random, rather than sequential order . T o use random, press the softkey under the RDM tab until Random Current Disc displays to play songs in random order . Press the same softkey again to turn off random play . h (Music Navigator): Press the softkey below h to play files in order by artist or album. The player scans the disc to sort the files by artist and album ID3 tag information. It can take several minutes to scan the[...]

Infotainment System 7-31 T o connect an iPod, connect one end of the USB cable that came with the iPod to the iPod ’ s dock connector and connect the other end to the USB port located in the center console. If the vehicle is on and the USB connection works, “ OK to disconnect ” and a GM logo may appear on the iPod and iPod appears on the radio's display . The iPod music appears on the radio ’ s display and begins playing. The iPod charges while it is connected to the vehicle if the vehicle is in the ACC/ACCESSORY or ON/RUN position. When the vehicle is turned off, the iPod automatically powers off and will not charge or draw power from the vehicle's battery . If you have an[...]

7-32 Infotainment System j (Pause): Press the softkey below j to pause the track. The tab appears raised when pause is being used. Press the softkey below j again to resume playback. Back: Press the softkey below the back tab to go back to the main display screen on an iPod, or the root directory on a USB storage device. c (Folder View): Press the softkey below c to view the contents of the current folder on the USB drive. T o browse and select files: 1. Press the softkey below c . 2. T urn f to scroll through the list of folders. 3. Press f to select the folder . If there is more than one folder , repeat Steps 1 and 2 until the folder is reached. 4. T urn f to scroll through the files in th[...]

Infotainment System 7-33 T o skip through large lists, the five softkeys can be used to navigate in the following order: . First softkey , first item in the list. . Second softkey , 1% through the list each time the softkey is pressed. . Third softkey , 5% through the list each time the softkey is pressed. . Fourth softkey , 10% through the list each time the softkey is pressed. . Fifth softkey , end of the list. Repeat Functionality T o use Repeat: Press the softkey below " or ' to select between Repeat All and Repeat T rack. " (Repeat All): Press the softkey below " to repeat all tracks. The tab appears lowered when Repeat All is being used. This is the default mode whe[...]

7-34 Infotainment System T o use an auxiliary input device, connect a 3.5 mm (1/8 in) cable to the radio's front auxiliary input jack. O (Power/V olume): Turn clockwise or counterclockwise to increase or decrease the volume of the portable player . Additional volume adjustments might have to be made from the portable device if the volume is not loud or soft enough. BAND: Press to listen to the radio when a portable audio device is playing. The portable audio device continues playing, so you might want to stop it or turn it off. CD/AUX (CD/Auxiliary): Press to select between CD, or Auxiliary . . When a CD is in the player the CD icon and a message showing the disc and/or track number dis[...]

Infotainment System 7-35 USB Supported Devices . USB Flash Drives . Portable USB Hard Drives . Fifth generation or later iPod . iPod nanos . iPod touch . iPod classic Not all iPods and USB Drives are compatible with the USB port. Make sure the iPod has the latest firmware from Apple ® for proper operation. iPod firmware can be updated using the latest iTunes ® application. See www .apple.com/ itunes. For help with identifying your iPod, go to www .apple.com/support. Rear Seat Infotainment Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle's audio system. The DVD player is part of the front radio. [...]

7-36 Infotainment System Headphones The RSE includes two 2-channel wireless headphones that are dedicated to this system. Channel 1 is dedicated to the video screen, while Channel 2 is dedicated to RSA selections. These headphones are used to listen to media such as CDs, DVDs, MP3/WMAs, DVD-As, radio, any auxiliary source connected to A/V jacks, or the auxiliary input jack, if the vehicle has this feature. The wireless headphones have an On/Off button, channel 1/2 switch, and a volume control. Switch the headphones to Off when not in use. Push the power button to turn on the headphones. An indicator light located on the headphones comes on. If the light does not come on, the batteries might [...]

Infotainment System 7-37 Battery Replacement T o change the batteries on the headphones: 1. T urn the screw to loosen the battery door located on the left side of the headphones. Slide the battery door open. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly , using the diagram on the inside of the battery compartment. 3. Replace the battery door and tighten the door screw . If the headphones are to be stored for a long period of time, remove the batteries and keep them in a cool, dry place. Audio/Video (A/V) Jacks The A/V jacks, located on the rear of the floor console, allow audio or video signals to be connected from an auxiliary device such as a [...]

7-38 Infotainment System How to Change the RSE Video Screen Settings The screen display mode (normal, full, and zoom), screen brightness, and setup menu language can be changed from the on screen setup menu by using the remote control. T o change a setting: 1. Press z . 2. Use n , q , p , o and r to navigate and use the setup menu. 3. Press z again to remove the setup menu from the screen. Audio Output Audio from the DVD player or auxiliary inputs can be heard through the following sources: . Wireless Headphones . V ehicle Speakers . V ehicle wired headphone jacks on the rear seat audio system, if the vehicle has this feature. The RSE system always transmits the audio signal to the wireless [...]

Infotainment System 7-39 Notice: A void directly touching the video screen, as damage may occur . See “ Cleaning the Video Screen ” later in this section for more information. Remote Control T o use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light could affect the ability of the RSE transmitter to receive signals from the remote control. If the remote control does not seem to be working, the batteries might need to be replaced. See “ Battery Replacement ” later in this section. Objects blocking the line of sight could also affect the function of the remote control. If a CD or DV[...]

7-40 Infotainment System When the DVD is playing, depending on the radio, play may be slowed down by pressing s then [ . The DVD continues playing in a slow play mode. Depending on the radio, perform reverse slow play by pressing s then r . T o cancel slow play mode, press s again. t (Previous T rack/Chapter): Press to return to the start of the current track or chapter . Press again to go to the previous track or chapter . This button might not work when the DVD is playing the copyright information or the previews. u (Next T rack/Chapter): Press to go to the beginning of the next chapter or track. This button might not work when the DVD is playing the copyright information or the previews. [...]

Infotainment System 7-41 Battery Replacement T o change the remote control batteries: 1. Slide the rear cover back, on the remote control. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly , using the diagram on the inside of the battery compartment. 3. Replace the battery cover . If the remote control is to be stored for a long period of time, remove the batteries and keep them in a cool, dry place. Tips and T roubleshoo ting Chart Problem Recommended Action No power . The ignition might not be turned ON/ RUN or in ACC/ACCESSORY . The picture does not fill the screen. There are black borders on the top and bottom or on both sides or it looks stretc[...]

7-42 Infotainment System Tips and T roubleshoo ting Chart (cont'd) Problem Recommended Action After stopping the player , I push Play but sometimes the DVD starts where I left off and sometimes at the beginning. If the stop button was pressed one time, the DVD player resumes playing where the DVD was stopped. If the stop button was pressed two times the DVD player begins to play from the beginning of the DVD. The auxiliary source is running but there is no picture or sound. Check that the RSE video screen is in the auxiliary source mode. Check the auxiliary input connections at both devices. Sometimes the wireless headphone audio cuts out or buzzes. Check for obstructions, low batteries[...]

Infotainment System 7-43 DVD Distortion Video distortion can occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. *Excludes the OnStar ® System. Cleaning the RSE Overhead Console When cleaning the RSE overhead console surface, use only a clean cloth dampened with clean water . Cleaning the Video Screen Use only a clean cloth dampened with clean water . Use care when directly touching or cleaning the screen, as damage could result. Rear Seat Audio (RSA) System For vehicles with Rear Seat Audio (RSA), [...]

7-44 Infotainment System P (Power): Press to turn the RSA on or off. V olume: Turn to increase or to decrease the volume of the wired headphones. The left knob controls the left headphones and the right knob controls the right headphones. SRCE (Source): Press to select between the radio (AM/FM/XM ™ ), CD, and if the vehicle has these features, DVD, front auxiliary , and rear auxiliary . © ¨ (Seek): Press to go to the previous or to the next station and stay there. This function is inactive, with some radios, if the front seat passengers are listening to the radio. Press and hold © or ¨ until the display flashes to tune to an individual station. The display stops flashing after the butt[...]

Infotainment System 7-45 PROG (Program): Press to go to the next preset radio station or channel set on the main radio. This function is inactive, with some radios, if the front seat passengers are listening to the radio. When a CD or DVD audio disc is playing, press PROG to go to the beginning of the CD or DVD audio. This function is inactive, with some radios, if the front seat passengers are listening to the disc. When a disc is playing in the CD or DVD changer , press PROG to select the next disc, if multiple discs are loaded. This function is inactive, with some radios, if the front seat passengers are listening to the disc. When a DVD video menu is being displayed, press PROG to perfor[...]

7-46 Infotainment System Bluetooth Controls Use the buttons located on the steering wheel to operate the in ‐ vehicle Bluetooth system. See Steering Wheel Controls on page 5 ‑ 3 for more information. b g (Push T o T alk) : Press to answer incoming calls, to confirm system information, and to start speech recognition. c x (Phone On Hook): Press to end a call, reject a call, or to cancel an operation. Pairing A Bluetooth enabled cell phone must be paired to the in ‐ vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected,[...]

Infotainment System 7-47 5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then confirms the name provided. 6. The system responds with “ <Phone name> has been successfully paired ” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Bluetooth ” . The system responds with “ Bluetooth ready ” followed by a tone. 3. Say “ List ” . The system lists all the paired Bluet[...]

7-48 Infotainment System Storing Name T ags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: . Store . Digit Store . Directory Using the Store Command The store command allows a phone number to be stored without entering the digits individually . 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Store ” . The system responds with “ Store, number please ” followed by a tone. 3. Say the complete phone number to be stored at once with no pauses. . If the system recognizes the number it r[...]

Infotainment System 7-49 2. Say “ Digit Store ” . The system responds with “ Please say the first digit to store ” followed by a tone. 3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . If an unwanted number is recognized by the system, say “ Clear ” at any time to clear the last number . . T o hear all of the numbers recognized by the system, say “ V erify ” at any time and the system will repeat them. 4. After the complete number has been entered, say “ Store ” . The system responds with “ Please say the name tag ” followed by a tone. 5. Say a n[...]

7-50 Infotainment System 3. Say the name tag to be deleted. The system responds with “ Would you like to delete, <name tag>? Please say yes or no ” . . If the name tag is correct, say “ Y es ” to delete the name tag. The system responds with “ OK, deleting <name tag>, returning to the main menu. ” . If the name tag is incorrect, say “ No ” . The system responds with “ No. OK, let's try again, please say the name tag. ” Using the Delete All Name T ags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar (if present). T o use the delete all name tags command: 1. Press and hold b g for two seconds. T[...]

Infotainment System 7-51 . If the system does not recognize the number , it confirms the numbers followed by a tone. If the number is correct, say “ Y es ” . The system responds with “ OK, Dialing ” and dials the number . If the number is not correct, say “ No ” . The system will ask for the number to be re ‐ entered. Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Digit Dial ” . The system responds with “ Digit dial using <phone name>, please say the first digit to dial ” followed by a tone. 3. Say the digit to be dialed one at a time. Following each digit, the system will rep[...]

7-52 Infotainment System Using the Re ‐ dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. After the tone, say “ Re ‐ dial ” . The system responds with “ Re ‐ dial using <phone name> ” and dials the last number called from the connected Bluetooth phone. Once connected, the person called will be heard through the audio speakers. Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. . Press b g and begin speaking to answer the call. . Press c x to ignore a call. Call W aiting Call waiting must be supported on the Bluetooth phone and enabled by the wir[...]

Infotainment System 7-53 T o Cancel Mute 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. After the tone, say “ Mute Call ” . The system responds with “ Resuming call ” . T ransferrin g a Call Audio can be transferred between the in ‐ vehicle Bluetooth system and the cell phone. T o T ransfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ T ransfer Call. ” The system responds with “ Transferring call ” and the audio will switch from the vehicle to the cell phone. T o T ransfer Audio to the In-V ehicle Bluetooth System The cellular phone must b[...]

7-54 Infotainment System Sending a Number During a Call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Dial ” . The system responds with “ Say a number to send tones ” followed by a tone. 3. Say the number to send. . If the system clearly recognizes the number it responds with “ OK, Sending Number ” and the dial tones are sent and the call continues. . If the system is not sure it recognized the number properly , it responds “ Dial Number , Please say yes or no? ” followed by a tone. If the number is correct, say “ Y es ” . The system responds with “ OK, Sending Number ” and the dial tones are sent and the call continues. Sending a [...]

Climate Controls 8-1 Climate Controls Climate Control Systems Climate Control Systems . . . . . . 8-1 Dual Automatic Climate Control System . . . . . . . . . . . . . . . . . . . . . . 8-4 Rear Climate Control System (Rear Climate Control Only) . . . . . . . . . . . . . . . 8-10 Rear Climate Control System (Rear Climate with Rear Seat Audio) . . . . . . . . . . . . . . . . . . . . . . 8-1 1 Air V ents Air V ents . . . . . . . . . . . . . . . . . . . . . 8-12 Climate Control Systems The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. T emperature Control C. Air Delivery Mode Control D. Air Conditioning E. REAR (Rear Climate Control) F . Re[...]

8-2 Climate Controls T emperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature of the air flowing from the system. Air Delivery Mode Control: T urn clockwise or counterclockwise to change the current airflow mode. By positioning the right knob between two modes, a combination of those two modes is selected. H (V ent): Air is directed to the instrument panel outlets. ) (Bi-Level): Air is divided between the instrument panel and floor outlets. Some air is directed towards the windshield and side window outlets. Cooler air is directed to the upper outlets and warmer air to the floor outlets. 6 (Floor): Air is directed to the floor outlets, with some of the[...]

Climate Controls 8-3 Using recirculation for long periods of time could cause the air inside of the vehicle to become too dry . T o prevent this from happening, after the inside of the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so water might drip under the vehicle while idling or after turning off the engine. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on when recirculation is on. When the engine is turned off, the recirculation mode automatically turns off and must be re ‐ selected when the engine is turned on again. This mode recirculates and helps to quic[...]

8-4 Climate Controls Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. AUTO C. Defrost D. Recirculation E. REAR (Rear Climate Control) F . Air Delivery Mode Control G. Driver Side T emperature Control H. Display I. Power (On/Off) J. Rear Window Defogger K. Air Conditioning L. P ASS (Passenger) M. Passenger Side T emperature Control Display Function Each time the temperature, mode, or fan control buttons are pressed, the climate control display shows that function along with the inside temperature setting. The outside temperature is displayed on the instrument panel cluster . O (On/Off): Press to tu[...]

Climate Controls 8-5 Automatic Operation AUTO (Automatic): The system automatically controls the inside temperature, the air delivery , and the fan speed. T o use automatic mode: 1. Press the AUTO button. When AUTO is selected, the current temperature(s) selected and AUTO is shown on the display . The current air delivery mode and fan speed also appear for approximately five seconds. When AUTO is selected, the air conditioning and air inlet are automatically controlled. The air conditioning runs when the outside temperature is over 4°C (40°F). The system is automatically set to outside air , unless it is hot outside and then the air inlet changes to recirculation mode to help quickly cool [...]

8-6 Climate Controls Driver Side T emperature Control: Press the + or − buttons to increase or decrease the driver side temperature. The driver side temperature display will show the temperature setting. Passenger Side T emperature Control: Press the + or − buttons to increase or decrease the passenger side temperature. The passenger side display will show the temperature setting. P ASS (Passenger): Press to set the passenger temperature to match the driver temperature setting. The P ASS indicator will turn off. When the passenger temperature setting is different than the driver setting, the P ASS indicator comes on. Manual Operation The air delivery mode or fan speed can be manually adj[...]

Climate Controls 8-7 - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is less than 4°C (40°F). Do not drive the vehicle until all the windows are clear . 0 (Defrost): Press to turn the defrost on or off. This mode quickly clears the windshield of fog or frost. Air is directed to the windshield, side window , and floor vents. In this mode, outside air is pulled inside the vehicle. The air conditioning system runs automatically in this setting, unless the outside temperature i[...]

8-8 Climate Controls The air conditioning system removes moisture from the air, so water might drip under the vehicle while idling or after turning off the engine. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on when recirculation is on. When the engine is turned off, the recirculation mode automatically turns off and must be re ‐ selected when the engine is turned on again. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. The recirculation mode cannot be used with floor , defog, or defrosting modes. If recirculation is select[...]

Climate Controls 8-9 Sensors The solar sensor , located in the defrost grille in the middle of the instrument panel, monitors the solar heat. Do not cover the solar sensor or the system will not work properly . The interior temperature sensor located on the instrument panel to the right of the steering column, measures the temperature of the air inside the vehicle. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature. The climate control system uses the information from thes[...]

8-10 Climate Controls Rear Climate Control System (Rear Climate Control Only) A. Fan Control B. T emperature Control C. Air Delivery Mode Control For vehicles with the rear climate control system, the controls are located on the rear of the center console. The system can also be controlled with the front controls. Press the REAR button on the front climate control system to turn the rear climate control system on or off. An indicator comes on when the rear system is on. The system also turns on if any of the rear controls are adjusted. Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is pressed. Independent Mode: This mode di[...]

Climate Controls 8-1 1 Rear Climate Control System (Rear Climate with Rear Seat Audio) A. Fan Control B. Air Delivery Mode Control C. T emperature Control For vehicles with the rear climate control system, the controls are located on the rear of the center console. Press the REAR button on the front climate control system to turn the rear climate control system on or off. The system also turns on if any of the rear controls, except for the C are pressed. An indicator comes on when the rear system is on. The system can also be turned off, by pressing and holding the C button. Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is[...]

8-12 Climate Controls N (Air Delivery Mode Control): Press to manually change the direction of the airflow . Repeatedly press the button until the desired mode appears on the display . H (V ent): Air is directed through the overhead outlets. ) (Bi-Level): Air is directed through the rear floor outlets, as well as the overhead outlets. 6 (Floor): Air is directed through the floor outlets. The rear system floor outlets are located under the third row seats. Air V ents Use the slider switch in the center of the outlet, to change the direction of the air flow . Use the thumbwheel near the outlet to control the amount of air flow or to shut off the airflow . Keep all outlets open whenever possibl[...]

Driving and Operating 9-1 Driving and Operating Driving Information Defensive Driving . . . . . . . . . . . . . 9-2 Drunk Driving . . . . . . . . . . . . . . . . . 9-2 Control of a V ehicle . . . . . . . . . . . 9-3 Braking . . . . . . . . . . . . . . . . . . . . . . . 9-3 Steering . . . . . . . . . . . . . . . . . . . . . . . 9-4 Off-Road Recovery . . . . . . . . . . . . 9-5 Loss of Control . . . . . . . . . . . . . . . . 9-5 Driving on Wet Roads . . . . . . . . . 9-7 Highway Hypnosis . . . . . . . . . . . . 9-7 Hill and Mountain Roads . . . . . . 9-8 Winter Driving . . . . . . . . . . . . . . . . . 9-9 If the V ehicle is Stuck . . . . . . . . 9-1 1 V ehicle Load Limits . . . . . . . . . . [...]

9-2 Driving and Operating Driving Information Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 3 ‑ 14 . { W ARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready . In addition: . Allow enough following distance between you and the driver in front of you. . Focus on the task of driving. (Continued) W ARNING (Continued) Driver distraction can cause collisions resulting in injury or possible death. These simple defensive driving techniques could save your life[...]

Driving and Operating 9-3 Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person's chance of being killed or permanently disabled is higher than if the person had not been drinking. Control of a V ehicle The following three systems help to control the vehicle while driving — brakes, steering, and accelerator . At times, as when driving on snow or ice, it is easy to ask more of those control systems than the tires and road can provide. Meaning, you can lose control of the vehicle. See Stab[...]

9-4 Driving and Operating If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be used when the brake is applied. Once the power assist is used up, it can take longer to stop and the brake pedal will be harder to push. Adding non ‐ dealer/non ‐ retailer accessories can affect vehicle performance. See Accessories and Modifications on page 10 ‑ 3 . Steering Power Steering If power steering assist is lost because the engine stops or the power steering system is not functioning, the vehicle can be s[...]

Driving and Operating 9-5 An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly , and just as quickly straighten the wheel once you have avoided the object. The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly . Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pav[...]

9-6 Driving and Operating Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle's three control systems. In the braking skid, the wheels are not rolling. In the steering or cornering skid, too much speed or steering in a curve causes tires to slip and lose cornering force. And in the acceleration skid, too much throttle causes the driving wheels to spin. If the vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the veh[...]

Driving and Operating 9-7 Driving on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep ‐ standing or flowing water . { W ARNING Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side. Y ou could lose control of the vehicle. After driving through a large puddle of water or a car/vehicle wash, lightly apply the brake pedal until the brakes work normally . Flowing or rushing water creates strong forces. Driving through flowing water could cause your vehicle to be carried away . If[...]

9-8 Driving and Operating . Keep your eyes moving — scan the road ahead and to the sides. . Check the rearview mirror and vehicle instruments often. Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission. . Going down steep or long hills, shift to a lower gear . { W ARNING If you do not shift down, the brakes could get so hot that they would not work well. Y ou would then have poor braking or even none going down a hill. Y ou could crash. Shift down to let [...]

Driving and Operating 9-9 Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive with caution, whatever the condition. Accelerate gently so traction is not lost. Accelerating too quickly causes the wheels to spin and makes the surface under the tires slick, so there is even less traction. T ry not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surfac[...]

9-10 Driving and Operating T o get help and keep everyone in the vehicle safe: . T urn on the hazard warning flashers. . T ie a red cloth to an outside mirror . { W ARNING Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle is stuck in the snow: . Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. (Continued) W ARNING (Continued) . Check again from time to time to be sure snow does not collect there. . Open a window about 5 cm (two inches) on the side of the vehicl[...]

Driving and Operating 9-1 1 If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed. This keeps the battery charged to restart the vehicle and to signal for help with the headlamps. Do this as little as possible to save fuel. If the V ehicle is Stuck Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow . If the vehicle has a traction system, it can often help to free a stuck vehicle. Refer to the vehicle's traction system in the Index. If stuck too severely for the traction system to free the vehicle, turn the traction system off and use th[...]

9-12 Driving and Operating V ehicle Load Limits It is very important to know how much weight your vehicle can carry . This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. T wo labels on your vehicle show how much weight it may properly carry , the Tire and Loading Information label and the Certification/Tire label. { W ARNING Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change (Continued) W ARNING (Continued) the way the vehicle handles. These could ca[...]

Driving and Operating 9-13 the front and rear axle. See “ Certification/Tire Label ” later in this section. Steps for Determining Correct Load Limit 1. Locate the statement “ The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs ” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if the “ XXX ” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of av[...]

9-14 Driving and Operating Example 2 A. V ehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). B. Subtract Occupant Weight @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). C. Available Cargo Weight = 1 13 kg (250 lbs). Example 3 A. V ehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs). B. Subtract Occupant Weight @ 91 kg (200 lbs) × 5 = 453 kg (1,000 lbs). C. Available Cargo Weight = 0 kg (0 lbs). Refer to your vehicle's tire and loading information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver , passengers, and cargo should never exceed your vehicle's capacity weight. Certification/Tire Labe[...]

Driving and Operating 9-15 GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GA WR). T o find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Y our dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline. Never exceed the GVWR for your vehicle or the GAWR for either the front or rear axle. { W ARNING Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (Continued) W ARNING (Continued) (GVWR), or either the maximum[...]

9-16 Driving and Operating Starting and Operating New V ehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: . If you have all-wheel drive, keep your speed at 88 km/h (55 mph) or less for the first 805 km (500 miles). . Do not drive at any one constant speed, fast or slow, for the first 805 km (500 miles). Do not make full-throttle starts. A void downshifting to brake or slow the vehicle. . A void making hard stops for the first 322 km (200 miles) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow [...]

Driving and Operating 9-17 Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key . Use the correct key , make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer . ( (LOCK/OFF): This position locks the ignition and transmission. The key can be removed in LOCK/OFF . The shift lever must be in P (Park) to turn the ignition switch to LOCK/OFF . The steering can bind with the wheels turned off center . If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY . If this doesn't work, then the vehicle needs service. ACC (ACC/ACCESSOR Y[...]

9-18 Driving and Operating Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. T o restart the engine when the vehicle is already moving, use N (Neutral) only . Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the transmission. Shift to P (Park) only when the vehicle is stopped. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition to ST AR T . When the engine starts, let go of the key . The idle speed will slow down as the engine warms. Do not race the engine immediately after starting it. Operate the engine and transmission gently to allow the oil to wa[...]

Driving and Operating 9-19 Notice: The engine is designed to work with the electronics in the vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer . If you do not, the engine might not perform properly . Any resulting damage would not be covered by the vehicle warranty . Engine Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F ( − 18°C). V ehicles with an engine coolant heater should be plugged in at least four hours before starting. Some models may have an internal thermostat in the co[...]

9-20 Driving and Operating Shifting Into Park { W ARNING It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly . Y ou or others could be injured. T o be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow . If you are pulling a trailer , see Driving Characteristics and T owing Tips on page 9 ‑ 45 . 1. Hold the brake pedal down and set the parking brake. See Parking Brake on page 9 ‑ 28 for more information. 2. Move the shift lever into P (Park) by holding in the button on the shift l[...]

Driving and Operating 9-21 Shifting Out of Park The vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: . Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and . Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN or ACC/ ACCESSORY and the regular brake pedal is applied. The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery . If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery . See Jump Starting on page 10 ‑ 78 for mo[...]

9-22 Driving and Operating Engine Exhaust { W ARNING Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). . The exhaust smells or sounds strange or different. . The exhaust system leaks due to corrosion or damage. . The vehicle ’ s exhaust system has been modified, damaged or improperly repaired. (Continued) W ARNING (Continued) . There are holes or openings in the vehicle body from damage or after-market modifications that are not completel[...]

Driving and Operating 9-23 { W ARNING It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly . Y ou or others could be injured. T o be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). Follow the proper steps to be sure the vehicle will not move. See Shifting Into Park on page 9 ‑ 20 . If parking on a hill and pulling a trailer , see Driving Character[...]

9-24 Driving and Operating the shift lever button before shifting from P (Park) when the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever , then push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear . See Shifting Out of Park on page 9 ‑ 21 . R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty . Shift to R (Reverse) only after the vehicle is stopped. T o rock the vehicle back and forth to get out of[...]

Driving and Operating 9-25 and performance. Use the brake to hold the vehicle on a hill. Do not use the accelerator pedal. L (Low): This position gives you access to gear ranges. This provides more engine braking but lower fuel economy than D (Drive). Y ou can use it on very steep hills, or in deep snow or mud. Manual Mode Electronic Range Select (ERS) Mode ERS mode allows you to choose the top-gear limit of the transmission and the vehicle's speed while driving down hill or towing a trailer . The vehicle has an electronic shift position indicator within the instrument panel cluster . When using the ERS Mode a number will display next to the L, indicating the current gear that has been [...]

9-26 Driving and Operating T ow/Haul Mode _ (T ow/Haul): The vehicle may have a T ow/Haul mode. The button is located on the instrument panel under the climate controls. Push the button to activate the system. Push it again to deactivate the system. Y ou can use this feature to assist when towing or hauling a heavy load. When T ow/Haul is activated the T ow/Haul symbol will come on the instrument panel cluster . See “ T ow/Haul Mode ” under Driving Characteristics and T owing Tips on page 9 ‑ 45 for more information. Automatic Engine Grade Braking Automatic Engine Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift sc[...]

Driving and Operating 9-27 Brakes Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away , ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal. If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light on page 5 ‑ 19 . If driving safely on a wet road and it becomes necessary to slam on the brakes and continue braking to avoid a sudden obstacle, a computer sen[...]

9-28 Driving and Operating Parking Brake T o set the parking brake, hold the regular brake pedal down, then push the parking brake pedal down. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 5 ‑ 18 . Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. T o release the parking brake, hold the regular brake pedal down, then push down momentarily on the parking brake pedal until you feel the pedal release. Slowly pull your foot up off the park brake pedal. If[...]

Driving and Operating 9-29 Ride Control Systems StabiliT rak System The vehicle has the StabiliTrak system which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. When you first start the vehicle and begin to drive away , the system performs several diagnostic checks to ensure there are no problems. The system may be heard or felt while it is working. This is normal and does not mean there is a problem with the vehicle. The system should initialize before the vehicle reaches 32 km/h (20 mph). In some cases, it may take approximately 3.2 km (2 miles) of driving before the system initiali[...]

9-30 Driving and Operating T raction control can be turned on by pressing and releasing the traction control disable button if not automatically shut off for any other reason. When the traction control system is turned off, the StabiliT rak light and the appropriate traction control off message will be displayed on the DIC to warn the driver . The vehicle will still have brake-traction control when traction control is off, but will not be able to use the engine speed management system. See “ Traction Control Operation ” next for more information. When the traction control system has been turned off, system noises may be heard and felt as a result of the brake-traction control working. It[...]

Driving and Operating 9-31 If cruise control is being used when the system activates, the StabiliT rak light will flash and cruise control will automatically disengage. Cruise control may be reengaged when road conditions allow . See Cruise Control on page 9 ‑ 31 . StabiliT rak may also turn off automatically if it determines that a problem exists with the system. If the problem does not clear itself after restarting the vehicle, see your dealer for service. Cruise Control With cruise control, a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator . Cruise control does not work at speeds below about 40 km/h (25 mph). When the brakes are app[...]

9-32 Driving and Operating [ (Cancel): Press to cancel cruise control without erasing the set speed from memory . Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low . The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed. { W ARNING If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. Y ou could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the I button to turn the cruise control system on. 2.[...]

Driving and Operating 9-33 Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. When the brakes are applied the cruise control is disengaged. Ending Cruise Control There are three ways to end cruise control: . Step lightly on the brake pedal. . Press the [ button. . Press the T button. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is t[...]

9-34 Driving and Operating How the System Works URP A comes on automatically when the shift lever is moved into R (Reverse). A single tone sounds to indicate the system is working. URP A operates only at speeds less than 5 mph (8 km/h). An obstacle is indicated by audible beeps. The interval between the beeps becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm (12 in) the beeps are continuous. T o be detected, objects must be at least 25.4 cm (10 in) off the ground and below liftgate level. Objects must also be within 2.5 m (8 ft) from the rear bumper . This distance may be less during warmer or humid weather . The system can be disabled through t[...]

Driving and Operating 9-35 Rear Vision Camera (RVC) The vehicle may have a Rear Vision Camera system. Read this entire section before using it. { W ARNING The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: . Detect objects that are outside the camera's field of view , below the bumper , or underneath the vehicle. . Detect children, pedestrians, bicyclists, or pets. Do not back the vehicle by only looking at the RVC screen, or use the screen during longer , higher speed backing maneuvers or where there could be cross-traffic. (Continued) W ARNING (Continued) Y our judged distances using the screen will differ from actual distances. So if you do not use prop[...]

9-36 Driving and Operating T urning the Rear Vision Camera System Off or On T o turn off the rear vision camera system, press and hold z , located on the inside rearview mirror , until the left indicator light turns off. The rear vision camera display is now disabled. T o turn the rear vision camera system on again, press and hold z until the left indicator light illuminates. The rear vision camera system display is now enabled and the display will appear in the mirror normally . V ehicles With Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the driver shifts the vehicle into R (Reverse),[...]

Driving and Operating 9-37 The delay that is received after shifting out of R (Reverse) is approximately 10 seconds. The delay can be cancelled by performing one of the following: . Pressing a hard key on the navigation system. . Shifting in to P (Park). . Reach a vehicle speed of 5 mph (8 km/h). There is a message on the rear vision camera screen that states “ Check Surroundings for Safety ” . Adjusting the Brightness and Contrast of the Screen T o adjust the brightness and contrast of the screen, press the MENU button while the rear vision camera image is on the display . Any adjustments made will only affect the rear vision camera screen. ] (Brightness) : T ouch the + (plus) or – (m[...]

9-38 Driving and Operating Rear Vision Camera Error Messages Service Rear Vision Camera System: This message can display when the system is not receiving information it requires from other vehicle systems. If any other problem occurs or if a problem persists, see your dealer . Rear Vision Camera Location The camera is located in the rear liftgate handle. The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper . The area displayed can vary depending on vehicle orientation or road conditions. The distance of the image that appears on the screen differs from the actual distance. The following illustration shows the field of vi[...]

Driving and Operating 9-39 When the System Does Not Seem T o Work Properly The rear vision camera system might not work properly or display a clear image if: . The RVC is turned off. See “ T urning the Rear Camera System On or Off ” earlier in this section. . It is dark. . The sun or the beam of headlights is shining directly into the camera lens. . Ice, snow , mud, or anything else builds up on the camera lens. Clean the lens, rinse it with water , and wipe it with a soft cloth. . The back of the vehicle is in an accident, the position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera and its position and mounting angle checked at your[...]

9-40 Driving and Operating Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. T o help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Look for the TOP TIER label on the fuel pump to ensure gasoline meets enhanced detergency standards developed by auto companies. A list of marketers providing TOP TIER Detergent Gasoline can be found at www .toptiergas.com. Recommended Fuel Use regular unleaded gasoline with a posted octane rating of 87 or higher . If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be[...]

Driving and Operating 9-41 California Fuel Requirements If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected. The malfunction indicator lamp could turn on and the vehicle might fail a smog ‐ check test. See Malfunction Indicator Lamp on page 5 ‑ 16 . If this occurs, return to your authorized dealer for diagnosis. If it is determined that the con[...]

9-42 Driving and Operating For customers who do not use TOP TIER Detergent Gasoline regularly , one bottle of GM Fuel System T reatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves. GM Fuel System T reatment PLUS is the only gasoline additive recommended by General Motors. It is available at your dealer . Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier . However , E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in[...]

Driving and Operating 9-43 T o open the fuel door, push the rearward center edge in and release and it will open. T o remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door . { W ARNING Fuel can spray out on you if you open the fuel cap too quickly . If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather . Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way . Be careful not t[...]

9-44 Driving and Operating Filling a Portable Fuel Container { W ARNING Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor . Y ou can be badly burned and the vehicle damaged if this occurs. T o help avoid injury to you and others: . Dispense fuel only into approved containers. . Do not fill a container while it is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground. (Continued) W ARNING (Continued) . Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete. . Do [...]

Driving and Operating 9-45 For information on towing a disabled vehicle, see T owing the Vehicle on page 10 ‑ 82 . For information on towing the vehicle behind another vehicle — such as a motorhome, see Recreational V ehicle T owing on page 10 ‑ 82 . Driving Characteristics and T owing Tips { W ARNING The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly . For example, if the trailer is too heavy , the brakes may not work well — or even at all. The driver and passengers could be (Continued) W ARNING (Continued) seriously injured. The vehicle may also be damaged; the resulting repairs would not be covered by the v[...]

9-46 Driving and Operating Pulling A T railer Here are some important points: . There are many laws, including speed limit restrictions that apply to trailering. Check for legal requirements with state or provincial police. . Consider using sway control. See T owing Equipment on page 9 ‑ 53 . . Do not tow a trailer at all during the first 800 km (500 miles) the new vehicle is driven. The engine, axle or other parts could be damaged. . During the first 800 km (500 miles) that a trailer is towed, do not drive over 80 km/h (50 mph) and do not make starts at full throttle. This reduces wear on the vehicle. . The vehicle can tow in D (Drive). Use a lower gear if the transmission shifts too ofte[...]

Driving and Operating 9-47 T ow/Haul Mode T ow/Haul assists when pulling a heavy trailer or a large or heavy load. The purpose of the T ow/Haul mode is to: . Reduce the frequency and improve the predictability of transmission shifts. . Provide the same solid shift feel as when the vehicle is unloaded. . Improve control of vehicle speed while requiring less throttle pedal activity . . Increase the charging system voltage to assist in recharging a battery installed in a trailer . Press this button located on the console to turn on and turn off the T ow/Haul mode. See T ow/Haul Mode on page 9 ‑ 26 . The T ow/Haul light on the instrument panel comes on to indicate that T ow/Haul mode has been [...]

9-48 Driving and Operating Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer . This can help to avoid situations that require heavy braking and sudden turns. Passing More passing distance is needed when towing a trailer . Because the rig is longer , it is necessary to go farther beyond the passed vehicle before returning to the lane. Backing Up Hold the bottom of the steering wheel with one hand. T o move the trailer to the left, move that hand to the left. T o move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making T urns Notice: Making very[...]

Driving and Operating 9-49 When towing at high altitude on steep uphill grades, engine coolant will boil at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle may show signs similar to engine overheating. T o avoid this, let the engine run while parked, preferably on level ground, with the transmission in P (Park) for a few minutes before turning the engine off. If the overheat warning comes on, see Engine Overheating on page 10 ‑ 18 . On a long uphill grade, shift down and reduce the vehicle speed to around 88 km/h (55 mph) to reduce the possibility of the engine and the transmission overh[...]

9-50 Driving and Operating Maintenance When T railer T owing The vehicle needs service more often when pulling a trailer . See this manual's Maintenance Schedule or Index for more information. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle lubricant, belts, cooling system and brake system. Inspect these before and during the trip. Check periodically to see that all hitch nuts and bolts are tight. Engine Cooling When T railer T owing The cooling system may temporarily overheat during severe operating conditions. See Engine Overheating on page 10 ‑ 18 . T railer T owing Three important considerations have to do with weight: .[...]

Driving and Operating 9-51 V ehicle Maximum T railer Weight *GCWR Front ‐ Wheel Drive 2,000 lbs (907 kg) 7,500 lbs (3 402 kg) Front ‐ Wheel Drive, V92 T railer T owing Package 5,200 lbs (2 359 kg) 10,250 lbs (4 649 kg) All ‐ Wheel Drive 2,000 lbs (907 kg) 7,700 lbs (3 493 kg) All ‐ Wheel Drive, V92 T railer T owing Package 5,200 lbs (2 359 kg) 10,450 lbs (4 740 kg) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversions. The GCWR for the vehicle should not be exceeded. Ask your dealer for our trailering information or advice. See Customer Assistance Offices on pag[...]

9-52 Driving and Operating If a weight-carrying hitch or a weight-distributing hitch is being used, the trailer tongue (A) should weigh 10 ‐ 15 percent of the total loaded trailer weight (B). After loading the trailer , weigh the trailer and then the tongue, separately , to see if the weights are proper . If they are not, adjustments might be made by moving some items around in the trailer . T railering may be limited by the vehicle's ability to carry tongue weight. T ongue weight cannot cause the vehicle to exceed the GVWR (Gross V ehicle Weight Rating) or the RGA WR (Rear Gross Axle Weight Rating). The effect of additional weight may reduce the trailering capacity more than the tota[...]

Driving and Operating 9-53 Weight is still below 3 266 kg (7,200 lbs) and you might think 318 additional kilograms (700 lbs) should be subtracted from the trailering capacity to stay within GCWR limits. The maximum trailer would only be 3 538 kg (7,800 lbs). Y ou may go further and think the tongue weight should be limited to less than 454 kg (1,000 lbs) to avoid exceeding GVWR. But the effect on the rear axle must still be considered. Because the rear axle now weighs 1 406 kg (3,100 lbs), 408 kg (900 lbs) can be put on the rear axle without exceeding RGAWR. The effect of tongue weight is about 1.5 times the actual weight. Dividing the 408 kg (900 lbs) by 1.5 leaves only 272 kg (600 lbs) of [...]

9-54 Driving and Operating Weight-Distributing Hitches and Weight Carrying Hitches A. Body-to-Ground Distance B. Front of V ehicle When using a weight-distributing hitch, the hitch must be adjusted so that the distance (A) remains the same both before and after coupling the trailer to the tow vehicle. Safety Chains Always attach chains between the vehicle and the trailer . Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Always leave just enough slack so the rig can turn. Never allow safety chains to drag on the ground. T railer Brakes A loaded trailer that weighs more than 450 kg (1,000 lbs) n[...]

Driving and Operating 9-55 *The fuse for this circuit is installed in the underhood electrical center , but the wires are not connected. They should be connected by your dealer or a qualified service center . If the back-up lamp circuit is not functional, contact your dealer . If a remote (non-vehicle) battery is being charged, press the T ow/Haul mode switch located on the center console near the climate controls. This will boost the vehicle system voltage and properly charge the battery . If the trailer is too light for T ow/Haul mode, turn on the headlamps (Non ‐ HID only) as a second way to boost the vehicle system and charge the battery . Electric T railer Brake Control Wiring Provisi[...]

9-56 Driving and Operating 2 NOTES[...]

V ehicle Care 10-1 V ehicle Care General Information General Information . . . . . . . . . . 10-2 California Proposition 65 W arning . . . . . . . . . . . . . . . . . 10-3 California Perchlorate Materials Requirements . . . . 10-3 Accessories and Modifications . . . . . . . . . . . . . . . 10-3 V ehicle Checks Doing Y our Own Service Work . . . . . . . . . . . . . . . 10-4 Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Engine Compartment Overview . . . . . . . . . . . . . . . . . . . 10-6 Engine Cover . . . . . . . . . . . . . . . . 10-7 Engine Oil . . . . . . . . . . . . . . . . . . . 10-8 Engine Oil Life System . . . . . 10-10 Automatic Transmission Fluid . . . . . . . . . . . .[...]

10-2 V ehicle Care Different Size T ires and Wheels . . . . . . . . . . . . . . . . . . . 10-51 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . 10-52 Wheel Alignment and Tire Balance . . . . . . . . . . . . . . . . . . . 10-53 Wheel Replacement . . . . . . . . 10-54 T ire Chains . . . . . . . . . . . . . . . . . 10-55 If a Tire Goes Flat . . . . . . . . . . 10-56 T ire Sealant and Compressor Kit . . . . . . . . . . . 10-58 Storing the T ire Sealant and Compressor Kit . . . . . . . . . . . 10-65 T ire Changing . . . . . . . . . . . . . . 10-66 Secondary Latch System . . . 10-75 Compact Spare T ire . . . . . . . . 10-77 Jump Starting Jump Starting . . . . . . . . . . . . . .[...]

V ehicle Care 10-3 California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals. California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless transmitters, may contain perchlorate materials. Special handling may be necessary . For additional information, see www .dtsc.ca.gov/hazardouswaste/ perchlorate. A[...]

10-4 V ehicle Care GM Accessories are designed to complement and function with other systems on the vehicle. Y our GM dealer can accessorize the vehicle using genuine GM Accessories. When you go to your GM dealer and ask for GM Accessories, you will know that GM-trained and supported service technicians will perform the work using genuine GM Accessories. Also, see Adding Equipment to the Airbag-Equipped V ehicle on page 3 ‑ 44 . V ehicle Checks Doing Y our Own Service Work { W ARNING Y ou can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. . Be sure you have sufficient knowledge, experience, the proper replacement part[...]

V ehicle Care 10-5 Hood T o open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver's side of the vehicle. 2. At the front of the vehicle, pull up on the center of the hood, and push the secondary hood release to the right. 3. After you have partially lifted the hood, gas struts will automatically take over to lift and hold the hood in the fully open position. Before closing the hood, be sure all filler caps are on properly . Pull the hood down to close. Lower the hood until the lifting pressure of the strut is reduced. Then allow the hood to fall and latch into place under its own weight. Check to m[...]

10-6 V ehicle Care Engine Compartment Overview[...]

V ehicle Care 10-7 A. Radiator Pressure Cap. See Cooling System on page 10 ‑ 14 . B. Engine Coolant Recovery Cap. See Cooling System on page 10 ‑ 14 . C. Remote Negative ( − ) T erminal. See Jump Starting on page 10 ‑ 78 . D. Engine Compartment Fuse Block on page 10 ‑ 30 . E. Remote Positive (+) T erminal. See Jump Starting on page 10 ‑ 78 . F . Power Steering Reservoir and Cap (under engine cover). See Power Steering Fluid on page 10 ‑ 20 . G. Engine Oil Fill Cap. See “ When to Add Engine Oil ” under Engine Oil on page 10 ‑ 8 . H. Engine Cover on page 10 ‑ 7 . I. Engine Oil Dipstick. See “ Checking Engine Oil ” under Engine Oil on page 10 ‑ 8 . J. Automatic T ran[...]

10-8 V ehicle Care Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10 ‑ 6 for the location of the engine oil dipstick. 1. T urn off the engine and give the oil several minutes to drain back into the oil pan. If this is not done, the oil dipstick might not show the actual level. 2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way . Remove it again, keeping the tip down, and check the level. When to Add Engine [...]

V ehicle Care 10-9 What Kind of Engine Oil to Use Look for three things: . GM6094M Use only an oil that meets GM Standard GM6094M. . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity , or thickness. Do not use other viscosity oils such as SAE 20W-50. . American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container . This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Notice: Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol. Fa[...]

10-10 V ehicle Care Engine Oil Life System When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter . This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably . For the oil life system to work properly , the system must be reset every time the oil is changed. When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary . A CHANGE ENGINE OIL SOON message comes on. Change the oil as soon as possible within the next 600 miles (1 000 km). It is possible that, if drivi[...]

V ehicle Care 10-1 1 If the vehicle has Driver Information Center (DIC) buttons: 1. T urn the ignition to ON/RUN, with the engine off. 2. Press the vehicle information button until OIL LIFE REMAINING displays. 3. Press and hold the set/reset button until “ 100% ” is displayed. Three chimes sound and the CHANGE ENGINE OIL SOON message goes off. 4. T urn the key to LOCK/OFF . If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer . Do not let used oil stay on your skin for[...]

10-12 V ehicle Care The transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature. If you need to check the transmission fluid level, please take the vehicle to your dealer . Engine Air Cleaner/Filter When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 80 000 km (50,000 mile) interval. See Scheduled Maintenance on page 1 1 ‑ 2 for more information. If you are driving in dusty/dirty conditions, inspect the filter at each engine oil change. See Engine Compartment Overview on page 10 ‑ 6 for the location of the engine air cleaner/filt[...]

V ehicle Care 10-13 A. Clamp B. Screws C. Housing Cover D. Filter E. Base 4. Loosen the outlet duct clamp (A). 5. Loosen the six housing cover (C) screws (B). 6. Remove the housing cover (C) with outlet duct. 7. Remove the filter (D) and any loose debris that may be found in the base (E). 8. Inspect or replace the filter (D). 9. Reverse Steps 2 through 6 to reinstall the housing cover and reconnect the electrical connector to the sensor . 10. Reinstall the engine cover . See Engine Cover on page 10 ‑ 7 . { W ARNING Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfir[...]

10-14 V ehicle Care Cooling System The cooling system allows the engine to maintain the correct working temperature. A. Engine Coolant Recovery T ank B. Radiator Pressure Cap C. Engine Cooling Fans { W ARNING An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before[...]

V ehicle Care 10-15 What to Use { W ARNING Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL ® coolant. Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else needs to be added. This mixture: . Gives freezing protection [...]

10-16 V ehicle Care the cooling system is cool before this is done. See Cooling System on page 10 ‑ 14 for more information. The coolant recovery tank cap has this symbol on it. When the engine is cold, the coolant level should be at or above the FULL COLD line marked on the recovery tank. When the engine is hot, the level could be higher than the FULL COLD line. If the coolant is below the FULL COLD line when the engine is hot, there could be a leak in the cooling system. If the coolant is low , add the coolant or take the vehicle to a dealer for service. How to Add Coolant to the Recovery T ank { W ARNING Y ou can be burned if you spill coolant on hot engine parts. Coolant contains ethyl[...]

V ehicle Care 10-17 W ARNING (Continued) cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap. If coolant is needed, add the proper mixture directly to the radiator , but be sure the cooling system is cool before this is done. 1. Detach fasteners and lift off the panel that covers the radiator cap. 2. Remove the radiator pressure cap when the cooling system, including the upper radiator hose, is no longer hot. T urn the pressure cap slowly counterclockwise about one full turn. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left in the system. 3. Keep turning the pressure cap slowly and remove it. 4. Fill the radiat[...]

10-18 V ehicle Care 8. Start the engine and let it run until the upper radiator hose feels warm. Any time during this procedure, watch out for the engine cooling fan(s). 9. If the coolant level inside the radiator filler neck is low , add more of the proper DEX-COOL coolant mixture through the filler neck until the level is back up to the base of the filler neck. Replace the pressure cap. Be sure to secure it tightly . Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur . Be sure the cap is properly and tightly secured. Engine Overheating The vehicle has several indicators to warn of engine overheating. There is an engine coolant temperatur[...]

V ehicle Care 10-19 If Steam Is Coming From The Engine Compartment { W ARNING Steam from an overheated engine can burn you badly , even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. T urn it off and get everyone away from the vehicle until it cools down. W ait until there is no sign of steam or coolant before you open the hood. If you keep driving when the vehicles engine is overheated, the liquids in it can catch fire. Y ou or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool. (Continued) W ARNING (Continued) See Overheated Engine Protection Operating Mode on page 10 ‑ 20 for i[...]

10-20 V ehicle Care displayed, turn off the engine until it cools down. Also, see “ Overheated Engine Protection Operating Mode ” next in this section. Overheated Engine Protection Operating Mode This emergency operating mode lets the vehicle be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, there is a significant loss in power and engine performance. The temperature gauge indicates an overheat condition exists. Driving extended distances and/or towing a trailer in the overheat protection mode should be avoided. Notice: After driv[...]

V ehicle Care 10-21 What to Use T o determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 1 1 ‑ 7 . Always use the proper fluid. Notice: Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle's warranty . Always use the correct fluid listed in Recommended Fluids and Lubricants on page 1 1 ‑ 7 . W asher Fluid What to Use When adding windshield washer fluid, be sure to read the manufacturer's instructions before use. If the vehicle will be operating in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding W asher Fluid When the windshield [...]

10-22 V ehicle Care Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly . { W ARNING The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When the brake wear warning sound is heard, have the vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair . Some driving conditions or climates can cause a brake squeal when the brakes are first applied or light[...]

V ehicle Care 10-23 Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10 ‑ 6 for the location of the reservoir . There are only two reasons why the brake fluid level in the reservoir might go down: . The brake fluid level goes down because of normal brake lining wear . When new linings are installed, the fluid level goes back up. . A fluid leak in the brake hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake fluid. Adding fluid does not correct a leak. I[...]

10-24 V ehicle Care Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir . { W ARNING With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake fluid. Notice: . Using the wrong fluid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. . If brake fluid is spilled on the vehicle's painted[...]

V ehicle Care 10-25 Starter Switch Check { W ARNING When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 9 ‑ 28 . Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts. 3. T ry to start the engine in each gear . The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. Automatic T ransmission Shift Lock Control System Check { W ARNING Whe[...]

10-26 V ehicle Care Park Brake and P (Park) Mechanism Check { W ARNING When you are doing this check, the vehicle could begin to move. Y ou or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. . T o check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking b[...]

V ehicle Care 10-27 For the proper size and type see Maintenance Replacement Parts on page 1 1 ‑ 9 . Backglass Wiper Blade T o replace the backglass wiper blade: 1. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position so care should be used when pulling it away from the vehicle. 2. Rotate the wiper blade assembly , hold the wiper arm in position, and push the blade away from the wiper arm. 3. Replace the wiper blade. 4. Return the wiper arm and blade assembly to the rest position on the glass. Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However , if your vehicle is damage[...]

10-28 V ehicle Care T aillamps, T urn Signal, Sidemarker , and Stoplamps A. Sidemarker Lamp B. T aillamp T o replace one of these bulbs: 1. Open the liftgate. See Liftgate on page 2 ‑ 9 . 2. Remove the convenience net, if the vehicle has one. 3. Remove the two taillamp nut covers. 4. Remove the two nuts holding the taillamp assembly in place. 5. Pull out the taillamp assembly . 6. T urn the bulb socket counterclockwise and pull it straight out to remove it from the taillamp assembly . 7. Pull the old bulb straight out of the bulb socket. 8. Push the new bulb straight into the bulb socket until it connects.[...]

V ehicle Care 10-29 9. Push the taillamp assembly back into its original location. When reinstalling the taillamp assembly , make sure the pin on the taillamp assembly lines up and is inserted correctly into the opening of the vehicle. 10. Reinstall the two nuts that hold the taillamp assembly in place. 1 1. Reinstall the two taillamp nut covers. Replacement Bulbs Exterior Lamp Bulb Number Rear Sidemarker Lamp 194 Rear T urn Signal and T aillamps 7443 (W21/5W) For replacement bulbs not listed here, contact your dealer . Electrical System High V oltage Devices and Wiring { W ARNING Exposure to high voltage can cause shock, burns, and even death. The high voltage systems in your vehicle can on[...]

10-30 V ehicle Care Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice, may cause wiper linkage damage. Always clear ice and heavy snow from the windshield before using the windshield wipers. If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed. Fuses and Circuit Break[...]

V ehicle Care 10-31 Fuses Usage A/C CLUTCH Air Conditioning Clutch ABS MTR Antilock Braking System (ABS) Motor AFS Adaptive Forward Lighting System Fuses Usage AIRBAG Airbag System AUX POWER Auxiliary Power AUX V AC PUMP Auxiliary V acuum Pump A WD All-Wheel-Drive System Fuses Usage BA TT 1 Battery 1 BA TT 2 Battery 2 BA TT 3 Battery 3 ECM Engine Control Module ECM 1 Engine Control Module 1 EMISSION 1 Emission 1 EMISSION 2 Emission 2 EVEN COILS Even Injector Coils F AN 1 Cooling Fan 1 F AN 2 Cooling Fan 2 FOG LAMP Fog Lamps FSCM Fuel System Control Module HORN Horn HTD MIR Heated Outside Rearview Mirror[...]

10-32 V ehicle Care Fuses Usage HV AC BL WR Heating, V entilation and Air Conditioning Blower L T HI BEAM Left High-Beam Headlamp L T LO BEAM Left Low ‐ Beam Headlamp L T PRK Left Parking Lamp L T TRLR STOP/TRN T railer Left Stoplamp and Turn Signal ODD COILS Odd Injector Coils PCM IGN Powertrain Control Module Ignition PWR L/GA TE Power Liftgate Fuses Usage PWR OUTLET Power Outlet REAR CAMERA Rear Camera RR APO Rear Accessory Power Outlet RR DEFOG Rear Defogger RR HV AC Rear Climate Control System RT HI BEAM Right High ‐ Beam Headlamp RT LO BEAM Right Low ‐ Beam Headlamp RT PRK Right Parking Lamp Fuses Usage RT TRLR STOP/TRN T railer Right Stoplamp and Turn Signal RVC SNSR Regulated V[...]

V ehicle Care 10-33 Fuses Usage TRLR BCK/UP T railer Back ‐ up Lamps TRLR BRK T railer Brake TRLR PRK LAMP T railer Parking Lamps TRLR PWR Trailer Power WPR/WSW Windshield Wiper/ W asher Relays Usage A/C CMPRSR CL TCH Air Conditioning Compressor Clutch AUX V AC PUMP Auxiliary V acuum Pump CRNK Switched Power F AN 1 Cooling Fan 1 Relays Usage F AN 2 Cooling Fan 2 F AN 3 Cooling Fan 3 FOG LAMP Fog Lamps HI BEAM High ‐ Beam Headlamps HID/ LO BEAM High Intensity Discharge (HID) Low ‐ Beam Headlamps HORN Horn IGN Ignition Main L T TRLR STOP/TRN T railer Left Stoplamp and Turn Signal Lamp PRK LAMP Park Lamp PWR/TRN Powertrain Relays Usage RR DEFOG Rear Window Defogger RT TRLR STOP/TRN T rail[...]

10-34 V ehicle Care Fuse Side Fuses Usage AIRBAG Airbag AMP Amplifier BCK/ UP/STOP Back ‐ up Lamp/ Stoplamp BCM Body Control Module CNSTR/ VENT Canister V ent CTSY Courtesy DR/LCK Door Locks DRL Daytime Running Lamps DRL 2 GMC HID Only/ Rear Fog Lamps-China Only DSPL Y Display FRT/WSW Front Windshield W asher HTD/ COOL SEA T Heated/Cooling Seats Fuses Usage HV AC Heating, V entilation and Air Conditioning INADV/ PWR/LED Inadvertent Power LED INFOTMNT Infotainment L T/TRN/SIG Driver Side Turn Signal MSM Memory Seat Module PDM Power Mirrors, Liftgate Release PWR MODE Power Mode PWR/MIR Power Mirrors RDO Radio REAR WPR Rear Wiper RT/TRN/SIG Passenger Side T urn Signal SP ARE Spare STR/WHL/ IL[...]

V ehicle Care 10-35 Relay Side Relays Usage L T/ PWR/SEA T Driver Side Power Seat Relay RT/ PWR/SEA T Passenger Side Power Seat Relay PWR/WNDW Power Windows Relay PWR/ COLUMN Power Steering Column Relay L/GA TE Liftgate Relay LCK Power Lock Relay REAR/WSW Rear Window W asher Relay Relays Usage UNLCK Power Unlock Relay DRL2 Daytime Running Lamps 2 Relay L T/UNLCK Driver Side Unlock Relay DRL Daytime Running Lamps Relay SP ARE Spare FRT/WSW Front Windshield W asher Relay[...]

10-36 V ehicle Care Wheels and Tires Tires Y our new vehicle comes with high-quality tires made by a leading tire manufacturer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details. For additional information refer to the tire manufacturer . { W ARNING Poorly maintained and improperly used tires are dangerous. . Overloading your tires can cause overheating as a result of too much flexing. Y ou could have an air-out and a serious accident. See Vehicle Load Limits on page 9 ‑ 12 . (Continued) W ARNING (Continued) . Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause seriou[...]

V ehicle Care 10-37 and service description. See the “ T ire Size ” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (C) DOT (Department of T ransportation) : The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of T ransportation Motor V ehicle Safety Standards. (D) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of T rans[...]

10-38 V ehicle Care compact spare tire, see Compact Spare Tire on page 10 ‑ 77 and If a Tire Goes Flat on page 10 ‑ 56 . (C) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of T ransportation) code is the T ire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. (E) Tire Inflation : The temporary use tire or compact spare tire should be inflated to 42[...]

V ehicle Care 10-39 (C) Aspect Ratio : A two ‐ digit number that indicates the tire height ‐ to ‐ width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (D) Construction Code : A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted ‐ bias ply construction. (E) Rim Diameter : Diameter of the wheel in inches. (F) Service Description : These characters represent the load index and speed rating of the tire. [...]

10-40 V ehicle Care Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings : A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards. The DOT code includes the T ire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer , production plant, brand, and date of production. GVWR : Gross V ehicle Weight Rating. See V ehicle Load Limits on page 9 ‑ 12 . GA WR FRT : Gross Axle Weight Rating for the front axle. See [...]

V ehicle Care 10-41 Outward Facing Sidewall : The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer , brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire : A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure : V ehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10 ‑ 42 and V ehicle Load Limits on page 9 ‑ 12 . Radial Ply Tire :[...]

10-42 V ehicle Care V ehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. V ehicle Placard : A label permanently attached to a vehicle showing the vehicle's capacity weight and the original equipment tire size and recommended inflation pressure. See “ T ire and Loading Information Label ” under V ehicle Load Limits on page 9 ‑ 12 . Tire Pressure T ires need the correct amount of air pressure to operate effectively . Notice: Do not let anyone tell you that under ‐ inflation or over ‐ inflation is all right. It is not. If your tires do not have enough air (under ‐ inflation), you can get the foll[...]

V ehicle Care 10-43 When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if the vehicle has one. The compact spare should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 10 ‑ 77 . How to Check Use a good quality pocket-type gauge to check tire pressure. Y ou cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under ‐ inflated. Check the tire's inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1.6 km (1 mile)[...]

10-44 V ehicle Care pressure telltale when one or more of your tires is significantly under ‐ inflated. Accordingly , when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under ‐ inflated tire causes the tire to overheat and can lead to tire failure. Under ‐ inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability . Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under ‐ inflation has no[...]

V ehicle Care 10-45 When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument panel cluster . If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label. See Vehicle Load Limits on page 9 ‑ 12 . At the same time a message to check the pressure in a specific tire appears on the Driver Information Center (DIC) display . The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed by th[...]

10-46 V ehicle Care TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message is also displayed. The low tire warning light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause the malfunction light and DIC message to come on are: . One of the road tires has been replaced with the spare tire, if your vehicle has one. The spare tire does not have a TPMS sensor . The TPMS malf[...]

V ehicle Care 10-47 The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. If increasing the tire's air pressure, do not exceed the maximum inflation pressure indicated on the tire's sidewall. T o decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gauge, or a key . Y ou have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops an[...]

10-48 V ehicle Care Tire Inspection We recommend that you regularly inspect your vehicle's tires, including the spare tire, if the vehicle has one, for signs of wear or damage. See When It Is Time for New Tires on page 10 ‑ 49 for more information. Tire Rotation T ires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). See Scheduled Maintenance on page 1 1 ‑ 2 . The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that the vehicle continues to perform most like it did when the tires were new . Any time you notice unusual wear , rotate the tires as soon as possible and check wheel alignment. Also check for [...]

V ehicle Care 10-49 { W ARNING Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency , use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later , if needed, to get all the rust or dirt off. See If a Tire Goes Flat on page 10 ‑ 56 . Make sure the spare tire, if the vehicle has one, is stored securely . Push, pull, and then try to rotate or turn the tire. If it moves, tighten the cable. See Tire Changing on page 10 ‑ 66 . When It Is Time fo[...]

10-50 V ehicle Care wear out before they degrade due to age. If you are unsure about the need to replace the tires as they get older , consult the tire manufacturer for more information. Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new , were designed to meet General Motors T ire Performance Criteria Specification (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating. This way , your vehicle will continue to have tires that are designed to give the same performance and vehicle safety , during normal use, as the origin[...]

V ehicle Care 10-51 { W ARNING If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly , causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle's tires with those that do not have a TPC Spec number , make sure they are the same size, load range, speed rating, and construction type (radial and bias ‐ belted tires) as your vehicle's original tires. V ehicles that have a tire pressure monitoring system could give an inaccurate low ‐ pressure warning if non ‐ TPC Spec rated tires are installed on your vehicle. Non ‐ TPC Spec rate[...]

10-52 V ehicle Care Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: T readwear 200 T raction AA T emperature A The following information relates to the system developed by the United States National Highway T raffic Safety Administr ation (NHTSA), which grades tires by treadwear , traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver , or temporary use spare tires,[...]

V ehicle Care 10-53 T raction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. W arning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. T emperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to di[...]

10-54 V ehicle Care Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air , replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Y our dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity , diameter , width, offset, and be mounted the same way as the one it replaces. If you need to replace any of the wheels, wheel bolts, wheel nuts, or T ire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equip[...]

V ehicle Care 10-55 Used Replacement Wheels { W ARNING Putting a used wheel on the vehicle is dangerous. Y ou cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Tire Chains { W ARNING Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends[...]

10-56 V ehicle Care If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly . If air goes out of a tire, it is much more likely to leak out slowly . But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. T ake your foot off the accelerator pedal and grip the steering wheel firmly . Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you [...]

V ehicle Care 10-57 { W ARNING Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. Y ou and they could be badly injured or even killed. Find a level place to change your tire. T o help prevent the vehicle from moving: 1. Set the parking brake firmly . 2. Put an automatic transmission shift lever in P (Park), or shift a manual transmission to 1 (First) or R (Reverse). (Continued) W ARNING (Continued) 3. T urn off the engine and do not restart while the vehicle is raised. 4. Do not allow passengers to remain in the vehicle. T o be certain the vehicle will not move, put blocks at the front and rear of the tire farthest away from the [...]

10-58 V ehicle Care Tire Sealant and Compressor Kit { W ARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9 ‑ 22 . { W ARNING Over-inflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure. [...]

V ehicle Care 10-59 This vehicle may have one of the following tire sealant and compressor kits. The kit includes: A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gauge D. Pressure Deflation Button (If equipped) E. T ire Sealant Canister F . Sealant/Air Hose (Clear) G. Air Only Hose (Black) H. Power Plug Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister . Check the tire sealant expiration date on the sealant canister . The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer . See “ Removal and Installation of the Sealant Canister ” [...]

10-60 V ehicle Care Using the Tire Sealant and Compressor Kit to T emporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inflate the tire faster . Always do a safety check first. See If a Tire Goes Flat on page 10 ‑ 56 . Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10 ‑ 65 .[...]

V ehicle Care 10-61 2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the sealant/air hose (F) onto the tire valve stem. T urn it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5 ‑ 9 . If the vehicle has an accessory power outlet, do not use the cigarette lighter . If the vehicle only has a cigarette lighter , use the cigarette lighter . [...]

10-62 V ehicle Care 1 1. Press the on/off button (B) to turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire, therefore, Steps 12 through 18 must be done immediately after Step 1 1. Be careful while handling the tire sealant and compressor kit as it could be warm after usage. 12. Unplug the power plug (H) from the accessory power outlet in the vehicle. 13. Turn the sealant/air hose (F) counterclockwise to remove it from the tire valve stem. 14. Replace the tire valve stem cap. 15. Replace the sealant/air hose (F), and the power plug (H) back in their original location. 16. If [...]

V ehicle Care 10-63 21. Dispose of the used sealant canister (E) and sealant/air hose (F) assembly at a local dealer or in accordance with local state codes and practices. 22. Replace it with a new canister available from your dealer . 23. After temporarily sealing a tire using the tire sealant and compressor kit, take the vehicle to an authorized dealer within a 100 miles (161 km) of driving to have the tire repaired or replaced. Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) T o use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 10 ‑ 56 . 1. Remove the tire se[...]

10-64 V ehicle Care 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5 ‑ 9 . If the vehicle has an accessory power outlet, do not use the cigarette lighter . If the vehicle only has a cigarette lighter , use the cigarette lighter . Do not pinch the power plug cord in the door or windo[...]

V ehicle Care 10-65 1 1. Press the on/off button (B) to turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage. 12. Unplug the power plug (H) from the accessory power outlet in the vehicle. 13. Disconnect the air only hose (G) from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap. 14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. 15. Place the equipment in the original storage location in the vehicle. The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may[...]

10-66 V ehicle Care 1. Press down on the latch tab and pull the cover off to access the storage compartment. 2. Press the two tabs on the quick release buckle to release the tire sealant and compressor kit strap. 3. Remove the sealant and compressor kit from its tray . T o store the tire sealant and compressor kit, reverse the steps. Tire Changing Removing T ools The tools needed to remove the spare tire are located in the storage compartment on the driver side, at the rear of the vehicle. 1. Open the jack storage compartment by pulling on the latch tab, located toward the rear of the vehicle, and pulling the cover off. A. T ool Bag B. Wing Bolt C. Jack 2. Remove the wing bolt (B) by turning[...]

V ehicle Care 10-67 The tools you will be using include the jack (A) and lug wrench (B). Removing the Spare Tire The compact spare tire is located under the vehicle, in front of the rear bumper . See Compact Spare Tire on page 10 ‑ 77 for more information about the compact spare. A. Rear Convenience Center B. Lug Wrench C. Storage Compartment Cap Hole D. Hoist Shaft E. Compact Spare T ire F . Retainer G. Hoist Shaft Assembly 1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment. 2. Open the carpet cutout that is located through the hole of the storage compartment. 3. Attach the lug wrench into[...]

10-68 V ehicle Care 5. T ilt the retainer and slip it through the wheel opening to remove the spare tire from the cable. 6. T urn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full ‐ size or a flat road tire under the vehicle. See “ Storing a Flat or Spare T ire and T ools ” later in this section. T o continue changing the flat tire, see “ Removing the Flat Tire and Installing the Spare Tire ” later in this section. If the spare tire will not lower , the secondary latch could be engaged. Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2. If it is not visible, see Secondary Latch System o[...]

V ehicle Care 10-69 5. If you still cannot lower the spare tire to the ground, see Secondary Latch System on page 10 ‑ 75 . Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See If a Tire Goes Flat on page 10 ‑ 56 for more information. 2. If the vehicle has a wheel cover, loosen the plastic nut caps with the wheel wrench. They will not come off. Then, using the flat end of the wheel wrench, pry along the edge of the cover until it comes off. Be careful; the edges may be sharp. Do not try to remove the cover with your bare hands. Store the wheel cover securely in the rear of the vehicle until you have the flat tire repaired or replaced. If the ve[...]

10-70 V ehicle Care Notice: If a jack is used to raise the vehicle without positioning it correctly , the vehicle could be damaged. When raising the vehicle on a jack, avoid contact with the rear axle control arms. 5. Do not raise the vehicle yet. Put the compact spare tire near you. { W ARNING Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { W ARNING Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. T o help avoid personal injury and vehicle damage, be sure to fit the jack lift head i[...]

V ehicle Care 10-71 9. Remove the plastic spare tire heat shield by pulling the rubber latch. Store the plastic spare tire heat shield. See “ Storing a Flat or Spare Tire and T ools ” later in this section for more information. { W ARNING Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency , use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later , if needed, to get all the rust or dirt off. See If a Tire Goes Flat on page 10 ‑ 56 . [...]

10-72 V ehicle Care 13. Lower the vehicle by attaching the lug wrench to the jack and turning the wrench counterclockwise. Lower the jack completely . { W ARNING Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12 ‑ 2 for original equipment wheel nut torque specifications. Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. T o avoid expensi[...]

V ehicle Care 10-73 { W ARNING Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. T o store the spare tire: 1. Lay the compact spare tire near the rear of the vehicle with the valve stem down. 2. Reinstall the plastic spare tire heat shield on the compact spare tire. 3. Slide the cable retainer through the center of the wheel and start to raise the compact spare tire. Make sure the retainer is fully seated across the underside of the wheel. 4. When the compact spare tire is almost in the stored position, turn the tire so the valve [...]

10-74 V ehicle Care 3. Put the flat tire in the rear storage area with the valve stem pointing toward the rear of the vehicle. 4. Pull the cable (A) through the door striker (E), the center of the wheel (D), and the plastic spare tire heat shield (C), as shown. 5. Hook the cable onto the outside portion of the liftgate hinges (B). 6. Hook the other end of the cable onto the outside portion of the liftgate hinge on the other side of the vehicle. 7. Pull on the cable to make sure it is secure. 8. Make sure the metal tube is centered at the striker . Push the tube toward the front of the vehicle. 9. Close the liftgate and make sure it is latched properly .[...]

V ehicle Care 10-75 Storing the T ools A. T ool Bag B. Wing Bolt C. Jack Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on. 1. Ensure that the bottom of the jack is facing toward you. 2. T urn the jack (C) on its side and place down on the holding bracket. 3. Reinstall the wing bolt (B) by turning clockwise. 4. T o replace the cover , line up the tab at the front of the cover with the notch in the cover opening. Push the cover in place and make sure that the rear clips are in the slots and push the cover closed. Store the center cap or the plastic bolt ‐ on wheel covers until a full size tire is put back on the vehicle. When you re[...]

10-76 V ehicle Care T o release the spare tire from the secondary latch: { W ARNING Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely , make sure no one is behind you or on either side of you as you pull the jack out from under the spare. 1. If the cable is not visible, start this procedure at Step 3. All ‐ Wheel ‐ Drive V ehicle shown 2. T urn the lug wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed. 3. Attach the lug wrench to the jack and raise the jack at least 10 turns. 4. Place the jack under the vehicle, ahead of the rear bumper . Position the center lift point of t[...]

V ehicle Care 10-77 8. Disconnect the lug wrench from the jack and carefully remove the jack. Use one hand to push against the spare tire while firmly pulling the jack out from under the spare tire with the other hand. 9. T ilt the retainer and slip it through the wheel opening when the spare tire has been completely lowered. 10. Turn the lug wrench clockwise to raise the cable back up if the cable is hanging. Have the hoist shaft assembly inspected as soon as you can. Y ou will not be able to store a spare tire using the hoist assembly until it has been repaired or replaced. Compact Spare Tire { W ARNING Driving with more than one compact spare tire at a time could result in loss of braking[...]

10-78 V ehicle Care And do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together . The All-Wheel Drive (A WD) system will be automatically disabled when you use the compact spare. T o restore the A WD and prevent excessive wear on the clutch in your A WD, replace the compact spare tire with a full-size tire as soon as possible. Notice: Tire chains will not fit the compact spare. Using them can damage the vehicle and can damage the chains too. Do not use tire chains on the compact spare. Jump Starting If the vehicle's battery has run down, you may want to use another vehicle and some jumper cables to start your v[...]

V ehicle Care 10-79 vehicle, and the bad grounding could damage the electrical systems. T o avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put an automatic transmission in P (Park) or a manual transmission in Neutral before setting the parking brake. If one of the vehicles is a four-wheel-drive vehicle, be sure the transfer case is not in Neutral. Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty . Always turn off the radio and other accessories when jump starting the vehicle. 3. T urn off the igni[...]

10-80 V ehicle Care { W ARNING Fans or other moving engine parts can injure you badly . Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know . Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative ( − ) will go to a heavy , unpainted metal engine part or to a remote negative ( − ) terminal if the vehicle has one. Do not connect positive (+) to negative ( − ) or you will get a short that would damage the bat[...]

V ehicle Care 10-81 9. Connect the other end of the negative ( − ) cable at least 18 inches (45 cm) away from the dead battery , but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less. Y our vehicle has a remote negative ( − ) terminal for this purpose. 10. Now start the vehicle with the good battery and run the engine for a while. 1 1. Try to start the vehicle that had the dead battery . If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs[...]

10-82 V ehicle Care T o disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery . 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery . 3. Disconnect the red positive (+) cable from the vehicle with the good battery . 4. Disconnect the red positive (+) cable from the other vehicle. T owing T owing the V ehicle T o avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer or a professional towing service if the disabled vehicle must be towed. T o tow the vehicle behind another vehicle for recreational purposes [...]

V ehicle Care 10-83 Here are some important things to consider before recreational vehicle towing: . What is the towing capacity of the towing vehicle? Be sure to read the tow vehicle manufacturer's recommendations. . What is the distance that will be travelled? Some vehicles have restrictions on how far and how long they can tow . . Is the proper towing equipment going to be used? See your dealer or trailering professional for additional advice and equipment recommendations. . Is the vehicle ready to be towed? Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed. Dinghy T owing If the vehicle is front-wheel ‐ drive, it can be dinghy towed from [...]

10-84 V ehicle Care 6. T o prevent the battery from draining while the vehicle is being towed, remove the 50 amp BA TT1 fuse from the underhood fuse block and store in a safe location. See Engine Compartment Fuse Block on page 10 ‑ 30 . 7. Release the parking brake. Notice: If the vehicle is towed without performing each of the steps listed under “ Dinghy T owing, ” the automatic transmission could be damaged. Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle. Notice: If 105 km/h (65 mph) is exceeded while towing the vehicle, it could be damaged. Never exceed 105 km/h (65 mph) while towing the vehicle. Once the destination is reached: 1. S[...]

V ehicle Care 10-85 Dolly T owing (Front-Wheel ‐ Drive V ehicles Only) T o tow a front-wheel ‐ drive vehicle from the front with two wheels on the ground: 1. Put the front wheels on a dolly . 2. Move the shift lever to P (Park). 3. Set the parking brake. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 5. Remove the key from the ignition. 6. Secure the vehicle to the dolly . 7. Release the parking brake. T owing the V ehicle From the Rear Notice: T owing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty . Never have the vehicle towed from the rear . Do not tow the vehicle from the rear[...]

10-86 V ehicle Care Appearance Care Exterior Care Cleaning Exterior Lamps/ Lenses Use only lukewarm or cold water , a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “ Washing the V ehicle ” later in this section. Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer . If the vehicle has a basecoat/ clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compou[...]

V ehicle Care 10-87 Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not be covered by the warranty . Do not use cleaning agents that are petroleum based or that contain acid or abrasives, as they can damage the paint, metal or plastic on the vehicle. Approved cleaning products can be obtained from your dealer . Follow all manufacturer directions regarding correct product usage, necessary safety precautions and appropriate disposal of any vehicle care product. Rinse the vehicle well, befor[...]

10-88 V ehicle Care Notice: Using strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, could damage the surface of the wheel(s). The repairs would not be covered by the vehicle warranty . Use only approved cleaners on aluminum or chrome-plated wheels. The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels. Notice: Using chrome polish on aluminum wheels could damage the wheels. The rep[...]

V ehicle Care 10-89 Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty . Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away . Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer . Larger areas of finish damage can be corrected in your dealer'[...]

10-90 V ehicle Care cleaned. Permanent damage can result from using cleaners on surfaces for which they were not intended. Apply the cleaner directly to the cleaning cloth to prevent over-spray . Remove any accidental over-spray from other surfaces immediately . Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window defogger . When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner . Cleaners can contain solvents that can become concentrated in the vehicle's interior . Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the vehicle'[...]

V ehicle Care 10-91 T o clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center . Continue cleaning, using a clean area of the cloth each time it becomes soiled. 4. Continue to gently rub the soiled area. 5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process with plain water . If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary . T est a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter . If the locally cleaned area gives any impression that a ring [...]

10-92 V ehicle Care Some commercial products may increase gloss on the instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Care of Safety Belts Keep belts clean and dry . { W ARNING Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water . Floor Mats If the floor mat has a snap retainer , a grommet in the driver side floor mat attaches to a hook on the floor of the vehicle to secure the floor mat. T o remove the floor mat, pull the mat towards[...]

Service and Maintenance 1 1-1 Service and Maintenance General Information General Information . . . . . . . . . . 1 1-1 Scheduled Maintenance Scheduled Maintenance . . . . . 1 1-2 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . 1 1-7 Maintenance Replacement P a r t s .. ..................... 1 1 - 9 Maintenance Records Maintenance Records . . . . . . 1 1-10 General Information Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty . As [...]

1 1-2 Service and Maintenance { W ARNING Performing maintenance work can be dangerous. Some jobs can cause serious injury . Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer to have a qualified technician do the work. See Doing Y our Own Service Work on page 10 ‑ 4 . At your dealer , you can be certain that you will receive the highest level of service available. Y our dealer has specially trained service technicians, uses genuine replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics. The proper replacement parts, fluids, and lubricants to use are listed in Recomme[...]

Service and Maintenance 1 1-3 work and reset the system. If the engine oil life system is reset accidentally , service the vehicle within 5 000 km/3,000 miles since the last service. Reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 10 ‑ 10 . When the CHANGE ENGINE OIL SOON message displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: . Maintenance I was performed the last time the engine oil was changed. . It has been 10 months or more since the CHANGE ENGINE OIL SOON message has dis[...]

1 1-4 Service and Maintenance . Body hinges and latches, key lock cylinders, hood latch assemblies, secondary latches, pivots, spring anchor and release pawl, hood and door hinges, rear folding seats, and liftgate hinges lubrication. See Recommended Fluids and Lubricants on page 1 1 ‑ 7 . More frequent lubrication may be required when vehicle is exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth makes them last longer , seal better , and not stick or squeak. . Restraint system component check. See Safety System Check on page 3 ‑ 29 . . Engine air cleaner filter inspection. See Engine Air Cleaner/Filter on page 10 ‑ 12 . Additional Required [...]

Service and Maintenance 1 1-5 First Engine Oil Change After Every 40 000 km/25,000 Miles . Fuel system inspection for damage or leaks. First Engine Oil Change After Every 80 000 km/50,000 Miles . Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 10 ‑ 12 . . Automatic transmission fluid change (severe service) for vehicles mainly driven in heavy city traffic in hot weather , in hilly or mountainous terrain, when frequently towing a trailer , or used for taxi, police, or delivery service. See Automatic T ransmission Fluid on page 10 ‑ 1 1 . . All ‐ wheel drive only: Transfer case fluid change (severe service) for vehicles mainly driven when frequently towing a [...]

1 1-6 Service and Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection. • • Rotate tires. • • Fluids visual leak check. • • Engine air cleaner filter inspection (vehicles driven in dusty conditions only). • • Brake system inspection. • • Steering and suspension inspection. • Engine cooling system inspection. • Windshield wiper blades inspection. • Body components lubrication. • Restraint system components check. • Engine air cleaner filter inspection (vehicles not[...]

Service and Maintenance 1 1-7 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. T o determine the proper viscosity for the vehicle's engine, see Engine Oil on page 10 ‑ 8 . Engine Coolant 50/50 mixture of clean, drinkable water and use only DEX-COOL ® Coolant. See Engine Coolant on page 10 ‑ 14 . Hydraulic Brake System DOT 3 Hydraulic Brake Fluid (GM Part No. U.S. 88862806, in Canada 88862807). Windshield W asher Optikleen ® W asher Solvent. Hydraulic Power Steering System GM Power Steer[...]

1 1-8 Service and Maintenance Usage Fluid/Lubricant Carrier Assembly — Differential (Rear Drive Module) and Transfer Case (Power Transfer Unit) SAE 75W ‐ 90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678). Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Hood Latch Assembly , Secondary Latch, Pivots, Spring Anchor , and Release Pawl Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Hood and Door Hinges and Rear Folding Seat Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Weatherstrip[...]

Service and Maintenance 1 1-9 Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer . Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15278634 A3083C Engine Oil Filter 89017524 PF48 Spark Plugs 1261 1882 41-107 Wiper Blades Front Driver – 62.5 cm (24.6 in) 15254805 — Front Passenger – 53.0 cm (20.8 in) 15254804 — Rear – 30.0 cm (1 1.6 in) 25920067 —[...]

1 1-10 Service and Maintenance Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Date Odometer Reading Serviced By Services Performed[...]

Service and Maintenance 1 1-1 1 Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed[...]

1 1-12 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed[...]

T echnical Data 12-1 T echnical Data V ehicle Identification V ehicle Identification Number (VIN) . . . . . . . . . . . . . . 12-1 Service Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . 12-1 V ehicle Data Capacities and Specifications . . . . . . . . . . . . . . 12-2 Engine Drive Belt Routing . . . 12-3 V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the left side of the vehicle. It can be seen through the windshield from outside. The VIN also appears on the V ehicle Certification and Service Parts labels and certificates of title and registration. Engine Identification The eighth [...]

12-2 T echnical Data V ehicle Data Capacities and Specifications The following approximate capacities are given in metric and English conversions. See Recommended Fluids and Lubricants on page 1 1 ‑ 7 for more information. Application Capacities Metric English Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer for more information. Cooling System 10.8 L 1 1.4 qt Engine Oil with Filter 5.2 L 5.5 qt Fuel T ank 83.3 L 22.0 gal T ransmission Fluid* (Drain and Refill) 5.0 L 5.3 qt Wheel Nut T orque 190 Y 140 lb ft *See Automatic T ransmission Fluid on page 10 ‑ 1 1 for informat[...]

T echnical Data 12-3 Engine Specifications Engine VIN Code T ransmission Spark Plug Gap 3.6L V6 Engine D Automatic 1.10 mm (0.043 in) Engine Drive Belt Routing 3.6L V6 Engine[...]

12-4 T echnical Data 2 NOTES[...]

Customer Information 13-1 Customer Information Customer Information Customer Satisfaction Procedure . . . . . . . . . . . . . . . . . . 13-1 Customer Assistance Offices . . . . . . . . . . . . . . . . . . . . . 13-3 Customer Assistance for T ext T elephone (TTY) Users . . . . . 13-4 Online Owner Center . . . . . . . . 13-5 GM Mobility Reimbursement P r o g r a m .................... 1 3 - 6 Roadside Assistance P r o g r a m .................... 1 3 - 6 Scheduling Service Appointments . . . . . . . . . . . . . . 13-8 Courtesy T ransportation P r o g r a m .................... 1 3 - 9 Collision Damage Repair . . . 13-10 Service Publications Ordering Information . . . . . . 13-13 Reporting Safe[...]

13-2 Customer Information STEP TWO : If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., call the Chevrolet Customer Assistance Center at 1-800-222-1020. In Canada, call General Motors of Canada Customer Communication Centre at 1-800-263-3777 (English), or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention. Have the following information available to give the Customer Assistance Representative: . V ehicle Identification Number (VIN). This is available from the vehicle registration or title, or the plate at the top left of the in[...]

Customer Information 13-3 STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims. The program provides for the review of the facts involved by an impartial third party arbiter , and may include an informal hearing before the arbiter . The program is designed so that the entire dispute settlement process, from the time you file your compl[...]

13-4 Customer Information From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) From U.S. Virgin Islands: 1-800-496-9994 Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 www .gm.ca 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For T ext T elephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Cus[...]

Customer Information 13-5 Online Owner Center Online Owner Center (U.S.) — www.gmownercenter .com/ chevrolet Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records . Find Chevrolet dealers for service nationwide . Exclusive privileges and offers . Recall notices for your specific vehicle . OnStar ® and GM Cardmember Services Earnings summaries Other Helpful Links: Chevrolet − www .chevrolet.com Chevrolet Merchandise — www .chevymall.com Help Center — www .chevrolet.com/ pages/mds/helpcenter/faq.do . F AQ . Contact Us My GM Canada (Canada) — www.gm[...]

13-6 Customer Information GM Mobility Reimbursement Program This program, available to qualified applicants for cost reimbursement of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/scooter lift for the vehicle. For more information on the limited offer visit www .gmmobility .com or call the GM Mobility Assistance Center at 1-800-323-9935. T ext telephone (TTY) users, call 1-800-833-9935. General Motors of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830. Roadside Assistance Program For U.S. purchased vehicles, call 1 ‐ 800 ‐ 243 ‐ 8872; (T ext telephone (TTY): 1 ‐ 88[...]

Customer Information 13-7 Chevrolet and General Motors of Canada Limited reserve the right to limit services or payment to an owner or driver if they decide the claims are made too often, or the same type of claim is made many times. Services Provided . Emergency Fuel Delivery: Delivery of enough fuel for the vehicle to get to the nearest service station. . Lock ‐ Out Service: Service is provided to unlock the vehicle if you are locked out. A remote unlock may be available if you have OnStar ® . For security reasons, the driver must present identification before this service is given. . Emergency T ow From a Public Road or Highway: T ow to the nearest Chevrolet dealer for warranty service[...]

13-8 Customer Information Services Specific to Canadian Purchased V ehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. . Lock-Out Service: V ehicle registration is required. . T rip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route. There is a limit of six requests per year . Additional travel information is also available. Allow three weeks for delivery . . T rip Interruption Benefits and Assistance: Must be over 250 kilometres from where your trip was started to qualify . General Motors [...]

Customer Information 13-9 Courtesy T ransportation Program T o enhance your ownership experience, we and our participating dealers are proud to offer Courtesy T ransportation, a customer support program for vehicles with the New V ehicle Limited W arranty (Base W arranty Coverage period in Canada) and extended powertrain, and hybrid specific warranty in both the U.S. and Canada. Several courtesy transportation options are available to assist in reducing your inconvenience when warranty repairs are required. Courtesy Transportation is not a part of the New V ehicle Limited W arranty . A separate booklet entitled “ W arranty and Owner Assistance Information ” furnished with each new vehicl[...]

13-10 Customer Information Courtesy Rental V ehicle Y our dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair . Rental reimbursement will be limited and must be supported by original receipts. This requires that you sign and complete a rental agreement and meet state/ provincial, local, and rental vehicle provider requirements. Requirements vary and may include minimum age requirements, insurance coverage, credit card, etc. Y ou are responsible for fuel usage charges and may also be responsible for taxes, levies, usage fees, excessive mileage, or rental usage beyond the[...]

Customer Information 13-1 1 Recycled original equipment parts may also be used for repair . These parts are typically removed from vehicles that were total losses in prior crashes. In most cases, the parts being recycled are from undamaged sections of the vehicle. A recycled original equipment GM part, may be an acceptable choice to maintain your vehicle's originally designed appearance and safety performance, however , the history of these parts is not known. Such parts are not covered by your GM New V ehicle Limited W arranty , and any related failures are not covered by that warranty . Aftermarket collision parts are also available. These are made by companies other than GM and may n[...]

13-12 Customer Information If a Crash Occurs If there has been an injury , call emergency services for help. Do not leave the scene of a crash until all matters have been taken care of. Move the vehicle only if its position puts you in danger , or you are instructed to move it by a police officer . Give only the necessary information to police and other parties involved in the crash. For emergency towing see Roadside Assistance Program on page 13 ‑ 6 . Gather the following information: . Driver's name, address, phone number . Driver's license number . Owner's name, address, phone number . V ehicle license plate . V ehicle make, model and model year . V ehicle Identification [...]

Customer Information 13-13 Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle, suspension, brakes, electrical, steering, body , etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual includes the Maintenance Schedule for all models. In-Portfolio: Includ[...]

13-14 Customer Information Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administr ation (NHTSA) in addition to notifying General Motors. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However , NHTSA cannot become involved in individual problems between you, your dealer , or General Motors. T o contact NHTSA, you may call the V ehicle Safety Hotline toll-fre[...]

Customer Information 13-15 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or T ransport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P .O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or 1-800-263-7854 (French), or write: General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 V ehicle Data Recording and Privacy Y our GM vehicle has a number of sophisticated computers that record information about the vehicle ’ s performance and how it is driven. For example[...]

13-16 Customer Information This data can help provide a better understanding of the circumstances in which crashes and injuries occur . Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender , age, and crash location) is recorded. However , other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. T o read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer , [...]

Customer Information 13-17 Radio Frequency Statement This vehicle has systems that operate on a radio frequency that comply with Part 15 of the Federal Communications Commission (FCC) Rules and with RSS-210/21 1 of Industry Canada. Operation is subject to the following two conditions: 1. The device may not cause interference. 2. The device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to any of these systems by other than an authorized service facility could void authorization to use this equipment.[...]

13-18 Customer Information 2 NOTES[...]

INDEX i-1 A Accessories and Modifications . . . . . . . . . . . . . . . . . 10-3 Accessory Power . . . . . . . . . . . . . . 9-17 Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . 9-55 Adding Equipment to the Airbag-Equipped V ehicle . . . . . 3-44 Adjustments Lumbar , Front Seats . . . . . . . . . . . 3-6 Air Cleaner/Filter , Engine . . . . . 10-12 Air V ents . . . . . . . . . . . . . . . . . . . . . . 8-12 Airbag System Check . . . . . . . . . . . . . . . . . . . . . . . . 3-45 How Does an Airbag Restrain? . . . . . . . . . . . . . . . . . . . 3-36 Passenger Sensing System . . . . . . . . . . . . . . . . . . . . . . 3-38 What Makes an Airbag Inflate? . . . . . . . . . . . .[...]

i-2 INDEX Blade Replacement, Wiper . . . 10-26 Blind Spot Mirrors . . . . . . . . . . . . . 2-17 Bluetooth . . . . . . . . . . . . . . . . . . . . . . 7-45 Brakes . . . . . . . . . . . . . . . . . . . . . . . . 10-22 Antilock . . . . . . . . . . . . . . . . . . . . . . . 9-27 Assist . . . . . . . . . . . . . . . . . . . . . . . . . 9-28 Fluid . . . . . . . . . . . . . . . . . . . . . . . . 10-23 Parking . . . . . . . . . . . . . . . . . . . . . . . 9-28 System Messages . . . . . . . . . . . . 5-32 Braking . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Break-In, New V ehicle . . . . . . . . . 9-16 Bulb Replacement . . . . . . . . . . . . 10-29 Halogen Bulbs . . . . . . . . . . . . . . [...]

INDEX i-3 Collision Damage Repair . . . . . 13-10 Compact Spare T ire . . . . . . . . . . 10-77 Compass . . . . . . . . . . . . . . . . . . . . . . . 5-6 Compressor Kit, Tire Sealant . . . . . . . . . . . . . . . . . . . . . . 10-58 Control of a V ehicle . . . . . . . . . . . . . 9-3 Convenience Net . . . . . . . . . . . . . . . 4-3 Convex Mirrors . . . . . . . . . . . . . . . . 2-16 Coolant Engine . . . . . . . . . . . . . . . . . . . . . . 10-14 Engine T emperature Gauge . . . . . . . . . . . . . . . . . . . . . . 5-12 Engine T emperature W arning Light . . . . . . . . . . . . . . . 5-20 Cooling System . . . . . . . . . . . . . . . 10-14 Engine Messages . . . . . . . . . . . . 5-33 Courtes[...]

i-4 INDEX Dual Automatic Climate Control System . . . . . . . . . . . . . . . . 8-4 DVD Rear Seat Entertainment System . . . . . . . . . . . . . . . . . . . . . . 7-35 DVD/CD Player . . . . . . . . . . . . . . . . 7-14 E Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . . . 9-55 Electrical System Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-30 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . 10-30 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . . . 10-33 Overload . . . . . . . . . . . . . . . . . . . 10-29 Engine Air Cleaner/Filter . . . . . . . . . . . 10-12 Check and Service Engine Soon Lamp . . . . . . . . . . . . . [...]

INDEX i-5 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-40 Additives . . . . . . . . . . . . . . . . . . . . . 9-41 Filling a Portable Fuel Container . . . . . . . . . . . . . . . . . . . 9-44 Filling the T ank . . . . . . . . . . . . . . . 9-42 Fuels in Foreign Countries . . . . 9-41 Gasoline Specifications . . . . . . . 9-40 Gauge . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Recommended . . . . . . . . . . . . . . . 9-40 Requirements, California . . . . . 9-41 System Messages . . . . . . . . . . . . 5-34 Fuel Economy Driving for Better . . . . . . . . . . . . . 1-22 Fuses Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-30 Fuses and Circuit Breakers .[...]

i-6 INDEX Hood . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 How to Wear Safety Belts Properly . . . . . . . . . . . . . . . . . . . . . . 3-18 I Ignition Positions . . . . . . . . . . . . . . 9-16 Ignition T ransmission Lock Check . . . . . . . . . . . . . . . . . . . . . . . 10-25 Immobilizer . . . . . . . . . . . . . . . . . . . . 2-15 Infants and Y oung Children, Restraints . . . . . . . . . . . . . . . . . . . . 3-48 Instrument Cluster . . . . . . . . . . . . . 5-1 1 Instrument Panel Storage Area . . . . . . . . . . . . . . . . . . 4-1 Introduction . . . . . . . . . . . . . . . . . . .iii, 7-1 J Jump Starting . [...]

INDEX i-7 Locks Automatic Door . . . . . . . . . . . . . . . . 2-8 Delayed Locking . . . . . . . . . . . . . . . 2-8 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Lockout Protection . . . . . . . . . . . . . 2-8 Power Door . . . . . . . . . . . . . . . . . . . . 2-8 Safety . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Loss of Control . . . . . . . . . . . . . . . . . 9-5 Lower Anchors and T ethers for Children (LA TCH SYSTEM) . . . . . . . . . . . . . . . . . . . . 3-54 Lumbar Adjustment . . . . . . . . . . . . . 3-6 Front Seats . . . . . . . . . . . . . . . . . . . . 3-6 M Maintenance Records . . . . . . . . . . . . . . . . . . . . . 1 1-10 Maintenance Schedule Reco[...]

i-8 INDEX O Object Detection System Messages . . . . . . . . . . . . . . . . . . . . 5-35 Odometer . . . . . . . . . . . . . . . . . . . . . . 5-12 Off-Road Recovery . . . . . . . . . . . . . . . . . . . . . . 9-5 Oil Engine . . . . . . . . . . . . . . . . . . . . . . . . 10-8 Engine Oil Life System . . . . . 10-10 Messages . . . . . . . . . . . . . . . . . . . . 5-34 Pressure Light . . . . . . . . . . . . . . . . 5-21 Older Children, Restraints . . . . . 3-46 Online Owner Center . . . . . . . . . . 13-5 OnStar ® System . . . . . . . . . . . . . . . 1-23 Operation, Infotainment System . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Outlets Power . . . . . . . . . . . . . . . . . . . . .[...]

INDEX i-9 Reading Lamps . . . . . . . . . . . . . . . . . 6-5 Rear Climate Control System . . . . . . . . . . . . . . . . . 8-10, 8-1 1 Rear Seat Audio (RSA) System . . . . . . . . . . . . . . . . . . . . . . . 7-43 Rear Seat Entertainment System . . . . . . . . . . . . . . . . . . . . . . . 7-35 Rear Seat Audio (RSA) . . . . . . . 7-43 Rear Seats . . . . . . . . . . . . . . . . . . . . 3-10 Rear Vision Camera (RVC) . . . . 9-35 Rear Window W asher/Wiper . . . . 5-6 Rearview Mirrors . . . . . . . . . . . . . . 2-19 Automatic Dimming . . . . . . . . . . . 2-19 Reclining Seatbacks . . . . . . . . . . . . 3-6 Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . . . 1 1-7 Recomm[...]

i-10 INDEX Safety Locks . . . . . . . . . . . . . . . . . . . . 2-8 Safety System Check . . . . . . . . . . 3-29 Satellite Radio . . . . . . . . . . . . . . . . . . 7-8 Scheduled Maintenance . . . . . . . 1 1-2 Scheduling Appointments . . . . . . 13-8 Sealant Kit, T ire . . . . . . . . . . . . . . 10-58 Seats Adjustment, Front . . . . . . . . . . . . . . 3-3 Head Restraints . . . . . . . . . . . . . . . 3-2 Heated and V entilated Front . . . 3-9 Heated Front . . . . . . . . . . . . . . . . . . 3-8 Lumbar Adjustment, Front . . . . . 3-6 Power Adjustment, Front . . . . . . 3-3 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 Reclining Seatbacks . . . . . . . . . . . 3-6 Third Row [...]

INDEX i-1 1 System Roof Rack . . . . . . . . . . . . . . . . . . . . . 4-4 System Check Automatic Transmission Shiftlock Control . . . . . . . . . . 10-25 T T achometer . . . . . . . . . . . . . . . . . . . . 5-12 T aillamps Bulb Replacement . . . . . . . . . . 10-28 T ext T elephone (TTY) Users . . . 13-4 Theft-Deterrent Systems . . . . . . . 2-15 Immobilizer . . . . . . . . . . . . . . . . . . . 2-15 Third-Row Seats . . . . . . . . . . . . . . . 3-12 T ime . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 T ires Buying New T ires . . . . . . . . . . . 10-50 Chains . . . . . . . . . . . . . . . . . . . . . . 10-55 Changing . . . . . . . . . . . . . . . . . . . 10-66 Compact Spare [...]

i-12 INDEX V V ehicle Canadian Owners . . . . . . . . . . . . . . . iii Control . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Load Limits . . . . . . . . . . . . . . . . . . . 9-12 Messages . . . . . . . . . . . . . . . . . . . . 5-31 Personalization . . . . . . . . . . . . . . . 5-40 Remote Start . . . . . . . . . . . . . . . . . . 2-5 Security . . . . . . . . . . . . . . . . . . . . . . 2-13 Speed Messages . . . . . . . . . . . . . 5-39 T owing . . . . . . . . . . . . . . . . . . . . . . 10-82 V ehicle Care Storing the Tire Sealant and Compressor Kit . . . . . . . 10-65 T ire Pressure . . . . . . . . . . . . . . . 10-42 V ehicle Identification Number (VIN) . . . . . . . . . . . . . .[...]