Français dropdown-ico

Cisco Systems AIR-CAP702I-x-K9 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Cisco Systems AIR-CAP702I-x-K9. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Cisco Systems AIR-CAP702I-x-K9 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Cisco Systems AIR-CAP702I-x-K9 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Cisco Systems AIR-CAP702I-x-K9 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Cisco Systems AIR-CAP702I-x-K9
- nom du fabricant et année de fabrication Cisco Systems AIR-CAP702I-x-K9
- instructions d'utilisation, de réglage et d’entretien de l'équipement Cisco Systems AIR-CAP702I-x-K9
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Cisco Systems AIR-CAP702I-x-K9 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Cisco Systems AIR-CAP702I-x-K9 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Cisco Systems en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Cisco Systems AIR-CAP702I-x-K9, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Cisco Systems AIR-CAP702I-x-K9, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Cisco Systems AIR-CAP702I-x-K9. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    G ETTING S TARTED G UIDE Cisco Aironet 700 Series Access Points June 2013 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Ports and Connectors 7 Configuring the Access Point 8 Mounting the Access Point 9 Deploying the Access Point on the Wireless Network 10 Troubleshooting 11[...]

  • Page 2

    2 1 About this Guide This Guide provides in structions on how to install and conf igure your Cisco Aironet 700 Seri es Access Point. The 700 Series Access Point is referred to as the 700 series or the access point in this document. 2 Introduction to the Access Point The 700 series supports high-performing two spatial stream rates over a deployab le[...]

  • Page 3

    3 War n in g IMPORT ANT SAFETY INSTRUCTIONS This warning symbol means d anger . Y ou are in a situation that could cause bod ily injury . Before you work on any equipment, be aware of the hazards invo lved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of ea c[...]

  • Page 4

    4 4 Unpacking T o unpack the access point , follow these steps: Step 1 Unpack and remove the access point and the accessory kit from the shipp ing box. Step 2 Return any pa cking material to the shippi n g container and save it for future use. Step 3 V erify that you have received the items lis ted below . If any item is missing or da maged, contac[...]

  • Page 5

    5 Figur e 1 Access P oint LED Indicator (t op) The ports and connections on the side of the access point are shown in Figure 2 . 1 LED indicator 347756 1[...]

  • Page 6

    6 Figur e 2 Access P oint P orts and Connection s (bot tom) 7 Configuring the Access Point This section describes how to connect the access point to a wir eless LAN controller . Because th e configuration process takes place on the co ntroller , see the Cisco Wireless LAN Controller C onfiguration Guide for additional information. This guide is ava[...]

  • Page 7

    7 The Controller Discovery Process The access point uses standard Control and Provisioning of Wireless Access Points Protocol (CAPW AP) to communicate between the controller and other wireless access points on the network. CAPW AP is a standard, interoperable pro tocol which enables an access controller to ma nage a collection of wirele ss terminat[...]

  • Page 8

    8 Preparing the Access Point Before you mount and deploy your access poin t, we recommend that you perform a site su rvey (or use the site planning tool) to determine the best location to install your access point. Y ou should have the following in formation about your wireless network available: • Access point locations. • Access point mountin[...]

  • Page 9

    9 Figure 3 Pr e-Installat ion Configuration Setup T o perform pre-installation con figuration, perform the following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco Prime Infras tructure procedures as de scri bed in the appropriate Cisc o wireless LA N [...]

  • Page 10

    10 e. If the operating system download is successful, the access point reboots. Step 3 Configure the access point if required. Use the contro ller CLI, controller GUI, or Cisco Prime Infrastructure to customize the access-point-spe cific 802.11n network settings. Step 4 If the pre-installation configuration is successful, the Status LED is green in[...]

  • Page 11

    11 10 Troubleshooting If you experience difficulty getting your access point installe d a nd running, look for a solution to your problem in this guide or in additional access point documentation. These, an d other documents, are available on Cisco.com. Guidelines for Using Cisco Ai ronet Lightweigh t Access Points Keep these guidelines in mind whe[...]

  • Page 12

    12 Troubleshooting the Ac cess Point Join Process Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signe d certificates are n ot enabled on the controller; the access point’ s a nd controller’ s regu latory domains don’t match, and so on. Controller software enables you to configure th e ac[...]

  • Page 13

    13 An access point sends all syslo g messages to IP address 255.255.255.255 b y default when any of the following conditions are met: • An access point running software release 5.2 or later has been newly deploy ed. • An existing access point running softw are release 5.2 or later has been re set after clearing the configuration. If any of thes[...]

  • Page 14

    14 Manufacturer: Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the followin g two conditions: 1. This device may not cause harmful interferenc e , and 2. This device must accept any interference received, incl uding interference that may cause undesired opera[...]

  • Page 15

    15 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet a ccess po ints in Ja pan. These guideline s are provided in both Japanese and English. Japanese Translation English Translation This equipment operates in the same freque ncy bandwidth as industri[...]

  • Page 16

    16 English Translation When installing the product, please use the provid ed or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Elect rical Appliance an d Material Safety Law proh ibits the use of UL-certified cables (that have the “UL” sh own on the code) for any other[...]

  • Page 17

    17 European Community, Switzerland, Norway, Iceland, and Liechtenstein Models: AIR-CAP702I-E-K9 AIR-SAP702I-E-K9 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC[...]

  • Page 18

    18 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure referr ed to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed. This device also conforms to the EMC re[...]

  • Page 19

    19 Generic Discussion on RF Exposure The Cisco products are designed to comply with the following na tional and international standard s on Human Exposure to Radio F requencies: • US 47 Code of Federal Regulations Pa rt 2 Subpart J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (9[...]

  • Page 20

    20 This Device Meets the In dustry Canada Guidelines fo r Exposure to Radio Waves The 700 series device includes a radio transmi tter and receiver . It is designed not to exceed the limits for exposure to ra dio waves (radio frequency electromagnetic fields) as refer e nced in Health Canada Safety Code 6. The guidelines include a substantial safety[...]

  • Page 21

    21 Chinese Translation English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequency de vices that have alre ady received a type-approv al, companies, business units or users should not change its frequencies, increase its power or change its original features a nd functions. Article [...]

  • Page 22

    22 Chinese Translation English Translation Low-power Radio-frequency Devices T echnical Spec ifications 4.7 Unlicensed National Information Infrastructure 4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operation s to reduce any potential for harmful inte rference to co-cha nnel MSS operations. 4.7.6 The U-NII device[...]

  • Page 23

    23 Operation of Cisco Aironet Access Points in Brazil This section contains special information for ope ration o f Cisco Aironet access points in Bra zil. Access Point Models AIR-CAP702I-T -K9 AIR-SAP702I-T -K9 Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a prot eção con tra interferência preju[...]

  • Page 24

    24 Step 2 Create the DHCP pool, including the ne cessary parameters such as default r outer and name server . A DHC P scope example is as follows: ip dhcp pool <pool name> network <IP Network> <Netmask> default-router <Default router> dns-server <DNS Server> Where: <pool name> is the name of the DHCP pool, such a[...]

  • Page 25

    25 14 Obtaining Documentation and Submitting a Service Request For information on obtaining documentati on, submitting a service request, and gathering additional information, see What’ s New in Cisco Product Documentation at: http://www .cisco.com/en/US/docs/general/wha tsnew/whatsnew .html . Subscribe to What’ s New in Cisco Product Documenta[...]

  • Page 26

    26 Cisco and the Cisco logo are trademarks or registered tra demarks of Cisco and/or its affiliates in the U.S. and other countries. T o view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their re spective owners. The use of the word partner does not imply a pa rtnersh[...]