Dodge Charger SRT (2010) manuel d'utilisation

O W N E R ’ S M A N U A L 2 0 1 0 Charger S R T I n f o r m a t i o n P r o v i d e d b y :[...]

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................ 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............................. 7 9 4 UNDERST ANDING YOUR INSTRUMENT P ANEL .................................. 1 [...]

I n f o r m a t i o n P r o v i d e d b y :[...]

INTRODUCTION CONTENTS 䡵 Intr oduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications/Alterations ............ 7 1 I n f o r m a t i o n P r o v i d e d b y :[...]

INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it r epresents pr ecision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with t[...]

1 INTRODUCTION 5 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against pr oce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information. Observe all W arnings and Cautio[...]

VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 INTRODUCTION 7 I n f o r m a t i o n P r o v i d e d b y :[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 2 ▫ W ireless Ignition Node (WIN) ............ 1 2 ▫ K e y F O B ........................... 1 3 ▫ Removing Key FOB From Ignition ......... 1 3 ▫ Key-In-Ignition Reminder ............... 1 4 䡵 Sentry Key 威 .......................... 1 [...]

▫ Using The Panic Alarm ................. 2 1 ▫ Pr ogramming Additional T ransmitters ...... 2 1 ▫ T ransmitter Battery Replacement .......... 2 1 ▫ General Information ................... 2 2 䡵 Remote Starting System — If Equipped ....... 2 3 ▫ How T o Use Remote Start ............... 2 3 䡵 Door Locks ........................... 2 [...]

▫ Supplemental Restraint System (SRS) - Airbags ............................ 4 9 ▫ Airbag Deployment Sensors And Controls . . . 55 ▫ Event Data Recorder (EDR) .............. 6 2 ▫ Child Restraints ...................... 6 4 䡵 Engine Break-In Recommendations .......... 7 3 䡵 Safety T ips ........................... 7 4 ▫ T ransporting [...]

A WORD ABOUT YOUR KEYS The W ir eless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three with detents and one that is spring-loaded. The detent posi- tions are LOCK, ACC, and ON. The ST ART position is a spring-loaded momentary contact position. When re- leased fr om the ST AR T position, the switch a[...]

Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking the glove box. Y ou can keep[...]

NOTE: • For vehicles not equipped with the Electronic V ehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. • For vehicles equipped with th[...]

NOTE: The Key-In-Ignition reminder only sounds when the Key Fob is placed in the LOCK or ACC ignition position. SENTR Y KEY 姞 The Sentry Key 威 Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locke[...]

Replacement Keys NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • For vehicles[...]

• This device must accept any interference that may be received, including interference that may cause undes- ired operation. VEHICLE SECURITY ALARM — IF EQUIPPED The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation. If something triggers the alarm, the V ehicle Secur[...]

NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the V ehicle Security Alarm. • The V ehicle Security Alarm remains armed during trunk entry . Pressing the TRUNK button will not disarm the V ehicle Security Alarm. If someone enters the vehicle through the trunk, and opens any door , the a[...]

The lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switch is turned ON from the LOCK position. NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually [...]

within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote Key Unlock, Driver Door/All Doors 1st Press This feature lets you pr ogram the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE[...]

T o Unlatch the T runk Press the TRUNK button on the RKE transmitter two times within five seconds to unlatch the trunk. Using the Panic Alarm T o turn the Panic Alarm feature on or off, press and hold the P ANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash,[...]

1. Battery access is through a door located on the rear of the Key Fob. Insert a small, flat blade screwdriver into the slot and gently pry open the access door . 2. Remove and replace the battery . A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 3[...]

If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter . The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , and some mobile or CB radios. REMOTE ST ARTING SYSTEM — IF E[...]

W ARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Mon- oxide (CO) which is odorless and colorless. Car- bon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, wi[...]

T o Exit Remote Start Mode without Driving the V ehicle Press and release the REMOTE ST AR T button one time, or allow the engine to run for the entire 15-minute cycle. NOTE: T o avoid unintentional shut downs, the system will disable the one time press of the REMOTE ST AR T button for two seconds after receiving a valid Remote Start request. T o E[...]

DOOR LOCKS Manual Door Locks T o lock each door , push the door lock plunger on each door trim panel downward. T o unlock each door , pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door , the door will lock. Therefor e, make sure the key is not inside the vehicle before closing the door[...]

Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door LOCK switch while the Key Fob is in the ignition, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the Key Fob in the vehicle. Remov- ing the Ke[...]

Automatic Door Locks Programming The Automatic Door Locks feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic V ehicle Information Center (EVIC), refer to “Electronic V ehicle Information Center (EVIC)/Personal Settings (Customer-Pr ogrammable Features)” in “Understand- ing Y our Instrument Panel” fo[...]

3. The transmission is in NEUTRAL or P ARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h). Automatic Unlock Doors on Exit Programming The Automatic Unlock Doors On Exit feature can be enabled or disabled as follows: • For vehicles equipped with the EVIC, refer to “Elec- tronic V [...]

Child Protection Door Lock T o provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child Protection Door Lock system. T o Engage the Child Protection Door Lock System 1. Open the rear door . 2. Insert the tip of the emergency key (or alike) into the child lock control and pull it upward. NOTE:[...]

W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Failure to follow this warning may result in serious injury or death. NOTE: • After engaging the Child Protection Door Lock sys- tem, always test the door from the inside to ma[...]

3. Repeat Steps 1 and 2 for the opposite rear door . NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. WINDOWS Power Windows The window controls on the driver’s door control all the door windows. There are single window contr ols on each passenger doo[...]

W ARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO-Down Feature The driver door power window switch and some model passenger door power [...]

T o close the window part way , lift the window switch to the first detent and r elease it when you want the window to stop. The power window switches will remain active for up to 60 minutes after the ignition switch is turned off. Open- ing either front door will cancel this feature. The time for this feature is programmable. Refer to “Electroni[...]

Reset Anytime the vehicle battery is disconnected or goes dead, the AUTO-up function will be disabled. T o reactivate the AUTO-up feature, perform the following procedure after vehicle power is restored: 1. Pull the window switch up to close window com- pletely and continue to hold the switch up for an additional two seconds after the window is clo[...]

TRUNK LOCK AND RELEASE The trunk lid can be released from inside the vehicle by pressing the TRUNK RELEASE button located on the instrument panel to the left of the steering wheel. NOTE: The transmission must be in P ARK before the button will operate. The trunk lid can be released from outside the vehicle by pr essing the TRUNK button on the Remot[...]

TRUNK SAFETY W ARNING W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in th[...]

• Advanced Front Airbags for driver and front passen- ger • Supplemental Side Airbag Inflatable Curtains (SABIC) for the driver and passengers seated next to a window — if equipped • An ener gy-absorbing steering column and steering wheel • Knee bolsters/blockers for front seat occupants • Front seat belts incorporate pretensioners to e[...]

Buckle up even though you are an excellent driver , even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries[...]

W ARNING! (Continued) • W earing your belt in the wrong place could make your injuries in a collision much worse. Y ou might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too. • T wo people should never be belted into a singl[...]

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt[...]

W ARNING! (Continued) • A belt that is worn under your arm is dangerous. Y our body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury . A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. W ear the belt over your shoulder so that your strongest bones will [...]

W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job properly . In a collision, it could even cut into you. Be sure the[...]

Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the shoulder belt can be adjusted upwar d or downward to position the belt away from your neck. Push and fully depress the button above the webbing to r elease the anchorage, then move it up or down to the position that fits you best. As a guide, if you are shorter th[...]

3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing. Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract t[...]

Seat Belt Pretensioners — If Equipped The seat belts for both fr ont seating positions may be equipped with pretensioning devices that ar e designed to remove slack fr om the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pre[...]

For front passenger seats equipped with BeltAlert, your vehicle is equipped to detect when it is occupied. The BeltAlert 威 warning system is not activated when the front passenger seat is unoccupied. The BeltAlert 威 warn- ing system may be triggered when an animal or heavy object is on the front passenger seat or when the seat is folded flat (i[...]

4. T urn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. BeltAlert 威 can be r eactivated by repeating this pr ocedure. NOTE: Although BeltAlert 威 has been deactivated, the Seat Belt Reminder Light will continue to illuminate as long as the driver’s seat bel[...]

Supplemental Restraint System (SRS) - Airbags This vehicle has Advanced Front Airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air- bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Airbag is mounted in the instrument panel, above the[...]

The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Airbags based upon seat position. [...]

• Supplemental Side Airbag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat T rack Position Sensors Advanced Front Airbag Features The Advanced Fr ont Airbag system has multistage driver and fr ont passenger airbags. This system pr ovides output appropriate to the s[...]

Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may of fer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential [...]

The system includes side impact sensors adjacent to both front and r ear seat occupants that ar e calibrated to deploy the SABIC airbags during impacts that requir e airbag occupant protection. W ARNING! • If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up hi[...]

W ARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that posi- tion. Children that are not big enough to wear the vehicle seat belt properly (see Section on Child Restraints) should be secured in[...]

If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center . Phone numbers are provided under ⬙ If Y ou Need Assistance”. W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In so[...]

Advanced Front Airbags are designed to provide addi- tional protection by supplementing the seat belts in certain frontal collisions depending on the severity and type of collision. Advanced Front Airbags are not ex- pected to reduce the risk of injury in rear , side, or rollover collisions. The Advanced Front Airbags will not deploy in all frontal[...]

Also, the ORC turns on the Airbag W arning Light in the instrument panel for approxi- mately six to eight seconds for a self-check when the ignition is first turned on. After the self-check, the Airbag W arning Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Airbag W arning Light, either momentarily [...]

separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in about 50 to 70 milliseconds. This is about half of the time it takes to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger . The Advanced Front Airbag gas is vented through the vent holes i[...]

Enhanced Accident Response System In the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the follow- ing functions: • Cut off fuel to the engine. • Fla[...]

• As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water . For nose or throat irritation,[...]

Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right [...]

Airbag W arning Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately . • The Airbag W arning Light does not come on for approximately six to eight seconds w[...]

2. Under certain circumstances, EDR data may not be recor ded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by Chrysler Group LLC and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve ve[...]

3. Requested by police under a legal warrant. 4. Otherwise requir ed by law . Data parameters that are recorded: • Diagnostic tr ouble code(s) and warning light status for electronically-contr olled safety systems, including the airbag system • V ehicle speed • Engine RPM • Brake switch status • Pedal position • And other parameters dep[...]

There are differ ent sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child. Infants and Child Restraints • Safety experts recommend that[...]

seats used in the forwar d-facing dir ection ar e for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year . These child seats are also held in the vehicle by the lap/shoulder belt or the LA TCH child restraint anchorage system. Refer to “LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CHildren)”. T[...]

W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward-facing child restraint should only be used in a rear seat. A rearward-f[...]

LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CHildren) Y our vehicle’s rear seat is equipped with the child restraint anchorage system called LA TCH. The LA TCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages [...]

Installing the LA TCH-Compatible Child Restraint System W e urge you to follow the manufacturer’s directions carefully when installing your child restraint. Not all child r estraint systems will be installed as described her e. Again, carefully follow the installation instructions that are provided with the child restraint system. The rear seat l[...]

means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear -facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. Y ou will first loosen the adjusters on the lower straps and on the tether strap so [...]

W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing Child Restraints Using the V ehicle Seat Belts The passenger seat belts[...]

If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. T o atta[...]

2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and r emove slack in the tether strap according to the child restraint manufacturer’s instruc- tions. NOTE: Ensure that the tether strap does not slip into the [...]

The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur . For the recommended viscosity and quality grades refer to “Maintenance Procedur es” in “Maintaining Y our V e- hicle”. NON-[...]

Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle [...]

Safety Checks Y ou Should Make Inside the V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collis[...]

W ARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury . • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from movi[...]

Periodic Safety Checks Y ou Should Make Outside the V ehicle T ires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure. Ligh[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirr ors .............................. 8 3 ▫ Inside Day/Night Mirror ................ 8 3 ▫ Automatic Dimming Mirror — If Equipped . . . 84 ▫ Outside Mirrors ...................... 8 4 ▫ Outside Mirrors Folding Feature — If Equipped ......................... 8 5 ▫ Driver’s O[...]

䡵 V oice Command — If Equipped ........... 1 1 6 ▫ V oice Command System Operation ........ 1 1 6 ▫ Commands ........................ 1 1 8 ▫ V oice T raining ...................... 1 2 1 䡵 Seats .............................. 1 2 1 ▫ Power Seats ........................ 1 2 2 ▫ Power Reclining Seats ................. 1 2 3 ▫ Lumb[...]

▫ Over head Console Map/Reading Lights .... 1 3 4 ▫ Interior Lights ...................... 1 3 5 䡵 W indshield W ipers And W ashers .......... 1 3 6 ▫ Intermittent W iper System .............. 1 3 7 ▫ W indshield W ashers .................. 1 3 7 ▫ Mist Feature ........................ 1 3 8 ▫ Headlights On W ith W ipers (A vailable W[...]

▫ Security ........................... 1 5 1 ▫ T roubleshooting T ips .................. 1 5 1 ▫ General Information .................. 1 5 2 䡵 Power Sunroof — If Equipped ............ 1 5 2 ▫ Opening Sunroof — Express ............ 1 5 3 ▫ Closing Sunroof — Express ............. 1 5 3 ▫ Pinch Protect Feature ................. 1 [...]

MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window . Headlight glare can be reduced by moving the small control under the mirr or to the night position (toward the rear of the vehicle). The mirror should be adjusted while set [...]

Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during [...]

W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger sid[...]

Power Mirrors The power mirror switch is located on the driver’s door trim panel, next to the power door lock switch. A rotary knob selects the left mirror , right mirror or off position. After selecting a mirror , move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a m[...]

Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor . T o use the mirror , rotate the sun visor downward and swing the mirror cover upward. The light turns on automatically . Closing the mirror cover turns off the light. Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-[...]

For Uconnect™ customer support, visit the following websites: • www .chrysler .com/uconnect • www .dodge.com/uconnect • www .jeep.com/uconnect • or call 1–877–855–8400 Uconnect™ Phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s mic[...]

Uconnect™ Phone Button Depending on the vehicle options, either the radio or the mirror will contain the two control buttons (Uconnect™ Phone button) and (V oice Command button) that will en- able you to access the system. V oice Command Button Actual button location may vary with the ra- dio. The individual buttons ar e described in the “Ope[...]

• For certain operations, compound commands can be used. For example, instead of saying ⬙ Setup ⬙ and then ⬙ Phone Pairing, ⬙ the following compound command can be said: ⬙ Setup Phone Pairing. ⬙ • For each feature explanation in this section, only the combined form of the voice command is given. Y ou can also break the commands into[...]

T o complete the pairing process, you will need to refer - ence your cellular phone Owner’s Manual. The Uconnect™ website may also provide detailed instruc- tions for pairing. The following are general phone to Uconnect™ Phone pairing instructions: • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ?[...]

Dial by Saying a Number • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Dial. ⬙ • The system will prompt you to say the number you want to call. • For example, you can say ⬙ 234-567-8901 ⬙ . • The Uconnect™ Phone will confirm the phone number and then dial. The number will appear in th[...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook New Entry . ⬙ • When pr ompted, say the name of the new entry . Use of long names helps the V oice Command and it is recom- mended. For example, say ⬙ Robert Smith ⬙ or ⬙ Robert ⬙ instead of ⬙ Bob. ⬙ • When prompted, enter the number designation (e.g., ?[...]

• Automatic download and update, if supported, begins as soon as the Bluetooth 威 wireless phone connection is made to the Uconnect™ Phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect™ Phone. • Depending on the maximum num[...]

NOTE: • The phone handset must support Bluetooth 威 OBEX transfers of phonebook entries to use this feature. • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth 威 , and you may see a message on the phone display that the Bluetooth 威 link is busy . In this case, the user must first disconnec[...]

After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or r eturn to the main menu. ⬙ Phonebook Edit ⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may hav[...]

Delete/Erase “All” Uconnect™ Phonebook Entries • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Erase All. ⬙ • The Uconnect™ Phone will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. ?[...]

Phone Call Features The following features can be accessed through the Uconnect™ Phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the Uconnect™ Phone. Check with your cellular service provider for the features that you[...]

in progr ess. T o go back to the first call, refer to ⬙ T oggling Between Calls ⬙ in this section. T o combine two calls, refer to ⬙ Conference Call ⬙ in this section. Place/Retrieve a Call From Hold T o put a call on hold, pr ess the button until you hear a single beep. This indicates that the call is on hold. T o bring the call back from [...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial. ⬙ • The Uconnect™ Phone will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the Uconnect™ Phone. Call Continuation Call continuation is the pr ogression of a phone call on the Uconnect™ Phone after t[...]

• Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect™ Phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and usab[...]

• The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly . W ARNING! Y our phone must be turned on and paired to the Uconnect™ Phone System to allow use of this vehicle feature in emergency situations, when the cellular phone has network coverage and stays paired to [...]

V oice Mail Calling T o learn how to access your voice mail, refer to ⬙ W orking with Automated Systems. ⬙ W orking with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. Y ou can use your Uconnect™ Phone to access a [...]

• Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “V oice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately . For example, if a prompt is asking ⬙ W ould you like to pair [...]

phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using V oice Command. NOTE: Certain brands of cellular phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after succes[...]

If you would like to connect or disconnect the Bluetooth 威 connection between a Uconnect™ Phone paired cellular phone and the Uconnect™ Phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the button to begin. • After the “Ready” prompt and the following beep, say ?[...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • At the next prompt, say ⬙ Delete ⬙ and follow the prompts. • Y ou can also press the button at any time while the list is being played, and then choose the phone you wish to delete. Things Y ou Should Know About Y our Uconnect™ Phone Uconnect™ [...]

T o restore the V oice Command system to factory default settings, enter the V oice T raining session via the above procedur e and follow the prompts. V oice Command • For best performance, adjust the rearview mirror to provide at least 1 ⁄ 2 in (1 cm) gap between the overhead console (if equipped) and the mirror . • Always wait for the beep [...]

• Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the entries are not similar . • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero). • Even though international dialing[...]

Bluetooth 威 Communication Link Cellular phones have been found to lose connection to the Uconnect™ Phone. When this happens, the connec- tion can generally be reestablished by switching the phone off/on. Y our cellular phone is recommended to remain in Bluetooth 威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or[...]

3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 1 1 I n f o r m a t i o n P r o v i d e d b y :[...]

1 12 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 13 I n f o r m a t i o n P r o v i d e d b y :[...]

V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 1 14 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o [...]

V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistan[...]

General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interfe[...]

NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the V oice Command button, listen for the beep, and say your command. Pressing the V oice Command button while the system is speaking is known as “barging in.” The sys[...]

Commands The V oice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pressing the V oice Command button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust t[...]

Radio FM T o switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to[...]

Memo T o switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recor ding, you may press the V oice Command button to stop recor ding. Y ou pr oceed by saying one of the following commands: − “Save” (to save the memo) − “Continue” (to[...]

NOTE: Keep in mind that you have to press the V oice Command button first and wait for the beep before speaking the “Barge In” commands. V oice T raining For users experiencing difficulty with the system recog- nizing their voice commands or numbers the Uconnect™ V oice “V oice T raining” feature may be used. 1. Press the V oice Command b[...]

Power Seats The power seat switch is on the outboard side of the seat near the floor . Use this switch to move the driver’s seat up or down, forward or rearwar d, or to recline the seatback. The passenger’s seat will move up or down, forward or rearward. W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of[...]

Power Reclining Seats The recliner control is located on the outboard side of the seat. W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Pow[...]

Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. T urn the control lever for- ward to increase and rearward to decrease the desired amount of lumbar support. Head Restraints Head restraints can reduce the risk of injury in the event of a r ear impact. The head r estraint should be adjusted so the top of t[...]

T o remove the head restraint, pull upward on the head restraint to its highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint. T o install the head restraint, insert the head restraint r ods into each guide, apply pressure down on the headrest until the head r estraint reache[...]

NOTE: Ensure that the fr ont of the head restraint is facing toward the front of the vehicle. W ARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the ve[...]

W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time. • Do not [...]

When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. W ARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or pas[...]

TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. Use the hood pr op r od (if equipped) to secu[...]

CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. W ARNING! Be sure the hood is fully latched before driving your vehicle. If the[...]

Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, park light, and instrument panel light operation. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light l[...]

The Headlights On with W ipers featur e can be enabled or disabled. Refer to “Electronic V ehicle Information Center (EVIC)/Customer-Pr ogrammable Features” in “Under- standing Y our Instrument Panel” for further information. Headlight Time Delay This feature provides the safety of headlight illumination for up to 90 seconds (programmable) [...]

Fog Lights The front fog light switch is built into the head- light switch. T o activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. T o turn off the front fog lights, either press headlight switch again or turn off the headlight switch. An indicator light in the instrument cluster ill[...]

T urn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: • If either light r emains on and does not flash, or ther e is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light w[...]

Interior Lights The interior lights come on when a door is opened. T o protect the battery , the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or ar e on because a door is open. This includes the glove box light, but no[...]

Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Interior Light Defeat (OFF) Rotate the dimmer control to the extreme bottom OFF position. The interior lights will remain off when the doors are open. Pa[...]

Rotate the end of the multifunction lever to the first detent past the intermittent settings for low-speed wiper operation, or to the second detent past the intermittent settings for high-speed wiper operation. CAUTION! T urn the windshield wipers off when driving through an automatic car wash. Damage to the wind- shield wipers may result if the wi[...]

W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with the defroster before and during windshield washer use. Mist Feature Push the multifunction lever inwar d (towar d the [...]

TIL T/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. T o unlock the steering column, pull the control handle outward. T o tilt [...]

ADJUST ABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows both the brake and accelerator pedal to move toward or away from the driver to provide improved position with the steering wheel. The switch is located on the front sid[...]

• The pedals can be adjusted while driving. • The pedals cannot be adjusted when the transmission is in REVERSE or when the Electr onic Speed Control is on. CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is st[...]

NOTE: In order to ensure proper operation, the Elec- tronic Speed Control System has been designed to shut down if multiple Speed Contr ol functions are operated at the same time. If this occurs, the Electr onic Speed Contr ol System can be reactivated by pushing the Electr onic Speed Control ON/OFF button and resetting the desired vehicle set spee[...]

• The Electronic Speed Control may not engage if a differ ent size tire is installed on one wheel, such as the compact spare tire. T o Deactivate The system will disable Electronic Speed Control without erasing the memory if you: • Softly tap the brake pedal. • Press the brake pedal. • Pull the Electronic Speed Control lever toward you (CAN[...]

T o decrease speed while Electronic Speed Control is set, push down and hold the Electronic Speed Control lever in SET DECEL. Release the Electronic Speed Contr ol lever when the desired speed is reached, and a new set speed will be established. T apping the Electronic Speed Control lever to SET DE- CEL once will result in a 1 mph (1.6 km/h) speed [...]

OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink 威 ) buttons and power sunroof switch may also be included, if equipped. Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn on the light. Press it [...]

GARAGE DOOR OPENER — IF EQUIPPED HomeLink 威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink 威 unit operates off your vehicle’s battery . The HomeLink 威 buttons ar e located in the overhead console, and contain [...]

W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people, pets, or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. [...]

2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink 威 buttons while keeping the EVIC display in view . For optimal training, point the battery end of the hand- held transmitter away from the HomeLink 威 . 3. Simultaneously , press and hold both the chosen HomeLink 威 button and the handheld transmitter button until the EVI[...]

This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer . NOTE: Y ou have 30 seconds in which to initiate the next step afte[...]

Gate Operator/Canadian Programming Canadian radio-frequency laws requir e transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink 威 to pick up the signal during programming. Similar to this Canadian law , some U.S. gate operators are designed to “time-out” in the sa[...]

Reprogramming A Single HomeLink 姞 Button T o r eprogram a channel that has been previously trained, follow these steps: 1. Place the ignition in the RUN position. 2. Press and hold the desired HomeLink 威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proc[...]

General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received including interference that may cause undesir ed operation NOTE: The transmitter has bee[...]

W ARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with[...]

sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the power sunroof switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the power sunr oof switch forward and hold for two seconds after the reversal occurs. This allows the sunroo[...]

Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switch will remain active for up to 60 minutes after the ignition switch is turned OFF . Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “Elec- tronic V ehi[...]

The 12 V olt power outlet next to the ash receiver tray has power available only when the ignition is in the ON or ACC positions. W ARNING! Do not place ashes inside the cubby bin located on the center console on vehicle’s not equipped with the ash receiver tray . A fire leading to bodily injury could result. The center console outlet is powered [...]

W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. (Continued) W ARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and fa[...]

CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly . Only use these inter- mittently and with greater caution. • After the use of high power draw accessories or long periods of the vehicle not being started (with accessories still plugged in), the v[...]

Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a r esting place for the r ear occupants elbows. STORAGE Console Features The center console contains[...]

T wo separate storage compartments are also located underneath the armrest. The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12 V olt power outlet and a molded-in coin holder (designed to hold various size coins). A slot in the le[...]

When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. W ARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or pas[...]

W ARNING! (Continued) • Place as much cargo as possible in front of the rear axle. T oo much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway . • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden s[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Features ............... 1 6 6 䡵 Instrument Cluster .................... 1 6 7 䡵 Instrument Cluster Descriptions ........... 1 6 8 䡵 Electronic V ehicle Information Center (EVIC) . . 178 ▫ Electronic V ehicle Information Center (EVIC) Displays ........................... 1 [...]

▫ Operating Instructions — V oice Command System (VR) — If Equipped ............. 1 9 5 ▫ Operating Instructions — Uconnect™ Phone — If Equipped ...................... 1 9 5 ▫ Clock Setting Procedur e — RBZ Radio ..... 1 9 5 ▫ Clock Setting Procedur e — RER/REN Radio ..................... 1 9 7 䡵 Media Center 130 (RES) — A[...]

▫ Controlling The iPod 威 Using Radio Buttons ........................... 2 2 5 ▫ Play Mode ......................... 2 2 6 ▫ List Or Browse Mode ................. 2 2 7 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RES Radios Only) .... 2 2 9 ▫ System Activation .................... 2 2 9 ▫ Electronic Serial Numb[...]

INSTRUMENT P ANEL FEA TURES 1 — Air Outlet 7 — Climate Control 13 — Hood Release 2 — Instrument Cluster 8 — Heated Seat Switch* 14 — T runk Release Button 3 — Hazard Switch 9 — Power Outlet 15 — Headlight Switch 4 — Electronic Stability Program OFF Button* 10 — Ash T ray* * If Equipped 5 — Glove Compartment 1 1 — Storage C[...]

INSTRUMENT CLUSTER 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 167 I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. T rip Odometer Button Press this button to change the display from odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer mode. Push in a[...]

7. Electronic Throttle Control (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if there is a problem with the Elec- tronic Throttle Control (ETC) system. If the light comes on while the engine is running, safely bring the vehicle to a complet[...]

W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to “Maintaining Y our V ehicle” and follow the warnings under the Cooling System Pressure Cap paragraph. 9. T[...]

12. Electronic Stability Program (ESP) / T raction Control System (TCS) Indicator Light If this indicator light flashes during accelera- tion, ease up on the accelerator and apply as little thr ottle as possible. Adapt your speed and driving to the prevailing road conditions, and do not switch off the Electronic Stability Program (ESP). 13. Electro[...]

15. High Beam Light This light will turn on when the high beam headlights are ON. Push the multifunction lever away from the steering wheel to switch the headlights to high beam. 16. Seat Belt Reminder Light This light will turn on for five to eight seconds as a bulb check when the ignition switch is first turned ON. A chime will sound if the drive[...]

for you to make a recor d of the odometer reading before the repair/service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. This display shows the Electronic V ehicle Information Center (EVIC) messages when the appr opriate conditions exist. For further information[...]

the brake booster , the ABS pump will r un when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake W arning Light which will tu[...]

The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 21. V ehicle Security Light — If Equipped This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle [...]

maintain correct tire pressur e, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Y our vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly . The TPMS malfunction indicator is combined with the low tire pressure tellta[...]

23. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is requir[...]

CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur . Immediate service is required. W ARNING! A malfunctioning catalytic converter , as referenced above, can reach high[...]

This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: • System status • V ehicle information warning message displays • T ire Pressur e Monitor System • Personal Settings (Customer-Programmable Features) • Compass dis[...]

Press the SCROLL button to scroll thr ough T rip Functions, Performance Pages (if equipped), Uconnect™ gps (if equipped), System Status Messages, and Personal Settings (Customer- Programmable Features). The SCROLL button also functions as a remote sound system con- trol. Refer to “Remote Sound System Controls”. Press the AUDIO MODE button to [...]

• Door(s) Ajar (with a single chime if vehicle is in motion) • T runk Ajar (with a single chime) • Oil Pressure • Oil Change Required (with single chime) • Low W asher Fluid (with a single chime) • Channel # T ransmit • Channel # T raining • Channel # T rained • Clearing Channels • Channels Cleared • Did Not T rain • Left Fr[...]

• Braking Distance (if equipped with Performance Pages) • 1/8 Mile (if equipped with Performance Pages) • 1/4 Mile (if equipped with Performance Pages) • Instantaneous G-Force (if equipped with Performance Pages) • Peak G-Force (if equipped with Performance Pages) • Digital Speedometer (if equipped with Performance Pages) Engine Oil Cha[...]

T rip Functions Press and release the MENU button until one of the following T rip Functions displays in the EVIC: • A verage Fuel Economy • Distance T o Empty • T rip A • T rip B • Elapsed T ime • Display Units of Measure in Press the SCROLL button to cycle through all the T rip Computer functions. The T rip Functions mode displays the[...]

When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of ⬙ LOW FUEL. ⬙ This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the ⬙ LOW FUEL ⬙ text and a new DTE value will display . • T rip A Shows[...]

Performance Pages — If Equipped W ARNING! Measurement of vehicle statistics with the Perfor- mance Pages is intended for off-highway or off-road use only and should not be done on any public roadways. It is recommended that these features be used in a controlled environment and within the limits of the law . The capabilities of the vehicle as mea[...]

• Dashes will display if the vehicle fails to reach 60 mph (100 km/h) in less then 10 seconds. • The time will continue to display until the FUNCTION SELECT button is pressed. • Pressing the FUNCTION SELECT button will clear the current run time and display the vehicle’s best 0-60 mph (0-100 km/h) time. • T o clear the vehicle’s best 0-[...]

1/8 Mile, 1/4 Mile When selected, this screen displays the time it takes the vehicle to travel 1/8 mile (1/4 mile) within 30 seconds and the vehicle’s speed when it reaches 1/8 mile (1/4 mile). • The feature will “ready” when the vehicle is at 0 mph (0 km/h). The word “READY” will flash when condi- tions are met for the event to begin. [...]

Digital Speedometer When selected, this screen displays vehicle speed and recor ds top speed. • Press and hold the FUNCTION SELECT button for three seconds to toggle between curr ent speed and top speed. • T o reset top speed, quickly press and release the FUNC- TION SELECT button when top speed is displayed. Driver-Selectable Surround Sound (D[...]

Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually . When the vehicle is new , the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. Y ou may also calibrate the compass by completing one or mor e 360 degree turns (in an area free from la[...]

NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Cell Phones, Lap- tops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor , and it may give false readings. 1. T urn the ignition switch ON. 2. Press and hold the HOME button for approximate[...]

used to select an item, and the AUDIO MODE button can be used to return to the previous menu. When the Map display is active, pressing the FUNCTION SELECT but- ton will change the Navigation Unit Display to the Menu. T urn-by-T urn Directions The EVIC displays T urn-by-T urn dir ections to a pro- grammed destination when T urn-by-T urn Navigation i[...]

Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in P ARK. Press and release the MENU button until Personal Set- tings displays in the EVIC. Use the SCROLL button to display one of the following choices. “Language” When in this display , you may select one[...]

Press is selected, you must press the RKE UNLOCK button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE UNLOCK button. T o make your selection, press and release the FUNCTION SELECT button until “Driver Door 1st Press” or “All Doors 1st Press” appears.[...]

“Delay T urning Headlights Off” When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. T o make your selection, press and release the FUNCTION SELECT button until “0,” “30,” “60,” or “90” appears. “T urn Headlights On with Remote Key Unlock?[...]

“Display Units of Measure in” The EVIC, odometer , and Uconnect™ gps (if equipped) can be changed between English and Metric units of measure. T o make your selection, press and release the FUNCTION SELECT button until “ENGLISH” or “MET - RIC” appears. MEDIA CENTER 730N/430 (RER/REN/RBZ) — AM/FM STEREO RADIO AND CD/DVD/HDD/NA V — [...]

3. T o move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. T o move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed. 4. T o move the minute forward, touch the screen where the wor d “Min” with the arrow pointing upwar d is [...]

Changing the T ime Zone 1. T urn on the radio. 2. T ouch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. T ouch the screen where the words “Set T ime Zone” are displayed. The time zone selection menu will appear on the screen. 4. Select a time zone by touching the screen where your selection appears.[...]

4. T o move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. T o move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed. 5. T o move the minute forward, touch the screen where the wor d “Min” with the arrow pointing upwar d is [...]

T ouch the screen where the words “Show T ime if Radio is Off” are displayed to change the current setting. Changing the T ime Zone 1. T urn on the radio. 2. T ouch the screen where the time is displayed. 3. T ouch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. T ouch the screen where the wo[...]

Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic V olume Control The electronic volume control turns contin[...]

4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5. T o exit, press any button/knob, or wait five seconds. R W/FF Pressing the R W (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates [...]

Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. AM/FM Button Press the buttons to select either AM or FM mode. SET/RND Button — T o Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory , press the SET/RND button. The symbol SET 1 will now show in the displa[...]

Operation Instructions — CD MODE For CD And MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recor dable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 t[...]

EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF . NOTE: Ejecting with the ignition OFF is not allowed on [...]

SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next ran- domly selected track. Press the RND button a second time to stop Random Play . No[...]

• Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and c[...]

Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the[...]

TIME Button (Auxiliary Mode) Press this button to change the display to time of day . The time of day will display for five seconds (when ignition is OFF). MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating [...]

Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic V olume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. T urning the ON/VOLUME control knob to the right increases th[...]

If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped W ith Uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate display of the time and radio frequency . Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the h[...]

TUNE Control T urn the rotary TUNE/SCROLL control knob clockwise to incr ease or counterclockwise to decrease the fr equency . Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCRO[...]

T oggle the MUSIC TYPE button to select the following format types: Program T ype 16-Digit Character Display No program type or un- defined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Foreign Language Language Information Inform Jazz Jazz News News Nostalgia Nostalga Oldies Oldies Program T ype [...]

By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next fr equency station with the same selected Music T ype name. The Music T ype function only operates when in the FM mode. If a preset button is activated while in the Music T ype (Program T ype) mode, the Music T ype mode will be exited and the rad[...]

Y ou may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stor ed into pushbutton memory . The stations stored in [...]

If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only . The use of[...]

TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display . R W/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or R W or another CD button is pressed. The RW (Reverse) button works in a similar manner . AM/FM Button Press the but[...]

The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a numbe[...]

rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, [...]

LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection[...]

Uconnect™ Multimedia (Satellite Radio) — If Equipped Satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for chil- dren,[...]

Sirius ID number will display . The Sirius ID number display will time out in two minutes. Pr ess any button on the radio to exit this screen. Selecting Uconnect™ Multimedia (Satellite) Mode Press the SA T button until ⬙ SA T ⬙ appears in the display . A CD may remain in the radio while in the Satellite radio mode. Satellite Antenna T o ensur[...]

SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it. SCAN Button Pressing [...]

T oggle the MUSIC TYPE button again to select the music type. By pressing the SEEK button when the Music T ype function is active, the radio will be tuned to the next channel with the same selected Music T ype name. If a preset button is activated while in the Music T ype (Program T ype) mode, the Music T ype mode will be exited and the radio will [...]

Every time a preset button is used, a corr esponding button number will display . Button s1-6 These buttons tune the radio to the channels that you commit to pushbutton memory (12 Satellite stations). Operating Instructions - Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in “Understanding The Features If Y our V ehicle”. UNIV[...]

Connecting The iPod 姞 Use the pr ovided connection cable to connect an iPod 威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles). Once the iPod 威 is connected and synchronized to the vehicle’s UCI system (iPod 威 may take a few seconds to connect), the iPod 威 starts charging and is rea[...]

Play Mode When switched to UCI mode, the iPod 威 automatically starts Play mode. In Play mode, use the following buttons on the radio faceplate to control the iPod 威 and display data: • Use the TUNE control knob to select the next or previous track. • T urning it clockwise (forward) by one click, while playing a track, skips to the next trac[...]

• Pressing the REPEA T button will change the iPod 威 mode to repeat the current playing track. • Press the SCAN button to use iPod 威 scan mode, which will play the first five seconds of each track in the current list and then forward to the next song. T o stop SCAN mode and start playing the desired track, when it is playing the track, pres[...]

• During all List modes, the iPod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster . • In List mode, the radio PRESET buttons are used as shortcuts to the following lists on the iPod 威 . • Preset 1 – Playlists • Pr[...]

CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer ’ s guidelines. • Placing items on the iPod 威 , or connections to the iPod 威 in the vehicle, can cause damage to the device and/or to the connectors. W ARN[...]

information, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www- .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID)[...]

bikes should be placed as far rearwar d as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree co[...]

INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display). R W/FF Pressing the R W (Rewi[...]

SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription. SET Button – T o Set the Pushbutton Memory When you are receiving a channel that you wish[...]

KICKER 姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECT ABLE SURROUND (DSS) – IF EQUIPPED Y our vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surround sound from any stereo audio source. A new feature of the KICKER 威 audio system offers the ability to choose surround sound for any audio source. “Aud[...]

media sources (DVDs, V ideo CDs, or other video media supported by the radio). Some audio will sound better in DSS modes, others in Stereo mode. When in “Audio Surround” mode, balance is set auto- matically . Fader control is available to add more sur- round audio if desired. VIDEO ENTERT AINMENT SYSTEM (VES)™ — IF EQUIPPED The optional V i[...]

• The LCD screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display . NOTE: Close the armrest after the LCD screen has been raised to its viewing position. • The touch screen radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers. • A batt[...]

• T wo wireless infrared headsets allow rear seat passen- gers to listen to the same or individual audio sources. Audio/V ideo RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player . 1. V ide[...]

REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the surface of the steering wheel at the three and nine o’clock positions. V ehicles equipped with steering wheel-mounted buttons are also equipped with the Electr onic V ehicle Information Center (EVIC). The EVIC features a driver-interactive display which is located in[...]

When the EVIC is in the Compass/T emp/ Audio screen, press the FUNCTION SE- LECT button to operate various radio, me- dia, and Universal Customer Interface (UCI) functions (i.e., advance presets, se- lect next folder , jump to or start playing songs in playlists, etc., depending on which radio is in the vehicle and if equipped with UCI). When the E[...]

RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your radio performance does not satisfactorily “cle[...]

Operation of the system is quite simple. Begin by turning the mode control knob (on the right) to AUTO, and place the blower control knob (on the left) to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only . The HI AUTO position should be used when more airflow is desired, or when rear seat occupants are pr[...]

NOTE: • The surface of the climate control panel and the top center of the instrument panel should be kept free of debris due to the location of the climate control sensors. Mud on the windshield may also cause poor operation of this system. • Extended use of recir culation may cause the windows to fog. If the interior of the windows begin to f[...]

4 UNDERST ANDING YOUR INSTRUMENT P ANEL 243 I n f o r m a t i o n P r o v i d e d b y :[...]

The operator can override the AUTO mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. ?[...]

conditioning. An indicator in the button illuminates when manual compressor operation is selected. NOTE: T o control the air conditioning manually , the mode selector must be moved out of the AUTO position. • Recirculation Control This button can be used to block out smoke, odors, dust, high humidity , or if rapid cooling is desired. The Recircul[...]

W inter Operation Use of the air Recirculation mode during W inter months is not recommended because it may cause window fogging. V acation Storage Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.[...]

Control Setting Suggestions for V arious W eather Conditions 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 247 I n f o r m a t i o n P r o v i d e d b y :[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedures .................... 2 5 3 ▫ Automatic T ransmission ............... 2 5 3 ▫ Normal Starting (T ip Start) ............. 2 5 4 ▫ Extreme Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) ............... 2 5 4 ▫ If Engine Fails T o Start ................ 2 5 4 ▫ After Starting ...........[...]

▫ General Information .................. 2 6 5 䡵 Driving On Slippery Surfaces ............. 2 6 5 ▫ Acceleration ........................ 2 6 5 ▫ T raction ........................... 2 6 6 䡵 Driving Through W ater ................. 2 6 6 ▫ Flowing/Rising W ater ................. 2 6 6 ▫ Shallow Standing W ater ............... 2 6 7 ?[...]

䡵 T ires — General Information ............. 2 9 2 ▫ T ire Pressure ....................... 2 9 2 ▫ T ire Inflation Pressures ................ 2 9 3 ▫ T ire Pressures For High Speed Operation . . . 295 ▫ Radial Ply T ir es ..................... 2 9 5 ▫ T ire Spinning ....................... 2 9 5 ▫ T read W ear Indicators ..........[...]

䡵 Adding Fuel ......................... 3 1 2 ▫ Fuel Filler Cap (Gas Cap) .............. 3 1 2 ▫ Loose Fuel Filler Cap Message ........... 3 1 4 䡵 V ehicle Loading ...................... 3 1 5 ▫ V ehicle Certification Label .............. 3 1 5 ▫ Gross V ehicle W eight Rating (GVWR) ...... 3 1 5 ▫ Gross Axle W eight Rating (GA WR) ...[...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. W ARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or other[...]

Normal Starting (Tip Start) NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Do not press the accelerator . Use the Fob with Integrated Key to briefly turn the ignition switch to the ST ART position and release it as soon as the starter engages. The starter motor will continue to[...]

If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold W eather” proce- dures, it may be flooded. T o clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the ST AR T position and release it as soon as the starter engages. The starter m[...]

AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, P ARK, or [...]

• Shift lever position • Accelerator position • V ehicle speed The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation, and the road characteristics. NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine[...]

W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into P ARK, remove the key fob from the ignition switch, and apply the parking brake. Once the key fob is removed[...]

Brake/T ransmission Interlock Manual Override There is an override for the BTSI that allows you to move the shift lever out of the P ARK position if an electrical system malfunction occurs (i.e., dead battery). T o access the override, remove the rubber tray from the storage bin located to the right of the shift lever . The override access port is [...]

Five-Speed Automatic T ransmission Shifting from DRIVE to P ARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when moving the shift lever between these gears. Gear Ranges P ARK This range supplements the parking brake by locking the transmission. The e[...]

W ARNING! Never use the P ARK position as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. The following indicators should be used to ensure that you have engaged the shift lever in the P ARK position: • When shifting into P ARK, move the shift lever [...]

CAUTION! Coasting the vehicle or driving for any other reason with the shift lever in NEUTRAL can result in transmission damage. W ARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. Y ou might lose control of the vehicle an[...]

T emporary T ransmission Limp Home Mode The transmission is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission will engage Limp Home Mode. If vehicle acceleration worsens, or the transmission no longer shifts, the transmission is most likely operating in the Limp Home Mode. In th[...]

AUTOSTICK 姞 AutoStick 威 is a driver-interactive transmission that of fers manual gear shifting to provide you with mor e contr ol of the vehicle. AutoStick 威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during p[...]

one second. The transmission will now operate automati- cally , shifting between the five available gears. General Information • Y ou can start out in first or second gear . The system will ignore attempts to upshift at too low of a vehicle speed. • The transmission will automatically downshift to first gear when coming to a stop. • Starting [...]

T raction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability . T o reduce this possibility , the following precau- tions should be observed: 1. Slow down during rainstorms [...]

Shallow Standing Water Although your vehicle is capable of driving through shallow standing water , consider the following Caution and W arning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicl[...]

W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances. Therefore, after driving through standing water , drive slowly and[...]

• Upon initial start-up in cold weather , the power steer- ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be consider ed normal, and it does not in any way damage the steering system. W ARNING! Continued operation with reduced power steering assist could pose a sa[...]

W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary , add fluid to restore to the proper indicated level. W ith a clean cloth, wipe any spilled fluid[...]

When the parking brake is applied with the ignition switch in the ON position, the “Brake W arning Light” in the instrument cluster will illuminate. NOTE: • When the parking brake is applied and the transmis- sion is placed in gear , the “Brake W arning Light” will flash. If vehicle speed is detected, a chime will sound to alert the drive[...]

W ARNING! (Continued) • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident. • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave the transmission in P ARK. Failure to do so may allow the vehic[...]

Anti-Lock Brake System The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. The electronic brake force distribution (EBD) pr events the rear wheels from over-braking and pro[...]

W ARNING! • The Anti-Lock Brake System contains sophisti- cated electronic equipment that may be suscep- tible to interference caused by improperly in- stalled or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability . Installation of such equipment should be performed by qualified pro[...]

All vehicle wheels and tires must be the same size and type and tires must be properly inflated to pr oduce accurate signals for the computer . Anti-Lock Brake Light The “Anti-Lock Brake Light” monitors the anti- lock brake system. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four s[...]

ELECTRONIC BRAKE CONTROL SYSTEM Y our vehicle is equipped with an advanced electronic brake control system commonly referr ed to as ESP . This system includes the Anti-Lock Brake System (ABS), the T raction Control System (TCS), the Brake Assist System (BAS), and the Electronic Stability Program (ESP). These systems work together to enhance both ve[...]

Brake Assist System (BAS) This system complements the ABS by optimizing the vehicle braking capability during emergency braking maneuvers. This system detects an emergency braking situation by sensing the rate and amount of brake appli- cation and then applies optimum pressur e to the brakes. This can help reduce braking distances. Applying the bra[...]

power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path. The ESP uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path,[...]

The ESP system has three available operating modes: ESP On This is the normal operating mode for the ESP . Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations. The ESP should only be turned OFF for specific reasons as noted in the following paragraphs. Partial Off The “Partial[...]

stopped with the engine running. After five seconds, a chime will sound, the “ESP/TCS Indicator Light” will illuminate, and the ⬙ ESP OFF ⬙ message will display in the vehicle odometer . Press and release the TRIP ODOM- ETER button located on the instrument cluster to clear this message. The “ESP OFF” message may appear in the Electroni[...]

W ARNING! W ith the ESP switched OFF , the enhanced vehicle stability offered by ESP is unavailable. In an emer- gency evasive maneuver , the ESP system will not en- gage to assist in maintaining stability . The “Full Off” ESP mode is intended for off-highway or off-road only . Synchronizing ESP The Malfunction Indicator Light for the ESP is co[...]

NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS Malfunction Indicator Light” will turn on momen- tarily each time the ignition switch is turned to the ON position. • Each time the ignition switch is turned to the ON position, the ESP System will be ON even if it was turned OFF previously . • The ESP Contr ol System will make bu[...]

NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. T ires designed to this standard have the tire size molded into the sidewall[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = T emporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect[...]

EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be a[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle.[...]

Tire T erminology and Definitions T erm Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold T ire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 [...]

Tire Loading and Tire Pressure T ire Placard Location NOTE: The proper cold tire inflation pressur e is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size desi[...]

Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressur es specified on the T ir e and Loading Information placard and in the “V ehicle Loading”[...]

4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available car go and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]).[...]

5 ST ARTING AND OPERA TING 291 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tire inflation pressur e is essential to the safe and satisfactory o[...]

W ARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abn[...]

CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressur e is defined as the tire pressu[...]

Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-s[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matt[...]

Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could los[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredict- able handling and stress to steeri[...]

SNOW TIRES Some areas of the country require the use of snow tires during the winter . Standard tires are of the all season type and satisfy this requir ement as indicated by the M+S designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four[...]

Tire Rotation – Standard Tires The suggested rotation method is the “side-to-side” as shown in the following diagram. Tire Rotation – All Season Tires The suggested rotation method for vehicles equipped with all season tires is the “forward-cr oss” as shown in the following diagram. T ire Rotation T ire Rotation 300 ST ARTING AND OPERA [...]

TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ir e Pressur e Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressur e will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperatur e decreases, the tire pressu[...]

For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressur e of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressur e to approximately 26 psi (179 kPa). This tire pressur e is[...]

NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to pr ovide warning of a tir e failure or condition. • The TPMS should not be used as a tire pressur e gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflat[...]

• V arious TPMS messages, which display in the Elec- tronic V ehicle Information Center (EVIC), and • TPM T elltale Light. The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor . The full size spare can be used in place of any of the four road tires. A spar e with a pressur e below the low-pressur e limit will not [...]

turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS W arning If a system fault is detected, the TPM T elltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. In addition, the EVIC will disp[...]

If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the TPM T elltale Light will no longer flash, and the ⬙ CHECK TPM SYSTEM ⬙ message will no longer display , and a pressur e value will display in place of the dashes. A system fault can occur due to any of [...]

2. If you install the compact spare tire in place of a road tire that has a pressur e below the low-pressur e warning limit, upon the next ignition switch cycle, the TPM T elltale Light will remain ON and a chime will sound. In addition, the graphic in the EVIC will still display a flashing pressure value. 3. After driving the vehicle for up to 20 [...]

The TPM sensors are regulated under one of the follow- ing licenses: United States ..................... KR5S120123 Canada ........................ 2671-S120123 FUEL REQUIREMENTS 6.1L Engine The 6.1L engine is designed to meet all emissions r egulations and pr ovide excel- lent fuel economy and performance when using high-quality premium unleaded g[...]

The manufactur er supports the use of reformulated gaso- line. Properly blended reformulated gasoline will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some[...]

T o fix a Non-FFV vehicle inadvertently fueled once with E85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory More extensive repairs will be required for prolonged exposure to E85 fuel. MMT In Gasoline M[...]

Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law . Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter t[...]

Carbon Monoxide Warnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicl[...]

NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinfor cement. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly [...]

W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground whi[...]

VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “V ehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Do not exceed the specified Gross V ehicle W eight Rating (GVWR) or the Gross Axle W eight Rating (GA WR). V ehicle Certification Label Y our vehicle has a V e[...]

W ARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicl[...]

NOTE: • Refer to the “V ehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR and GA WRs. • Refer to the “T ire Placard” for your vehicle’s proper tire pressur e. TRAILER TOWING T railer towing with this vehicle is not recommended. RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational to[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................ 3 2 0 䡵 If Y our Engine Overheats ................ 3 2 0 䡵 TIREFIT Kit ......................... 3 2 1 ▫ TIREFIT Storage ..................... 3 2 2 ▫ TIREFIT Kit Components And Operation . . . 322 ▫ TIREFIT Usage Precautions ............. 3 2 4 ▫ Sealing [...]

HAZARD W ARNING FLASHER The Hazard W arning flasher switch is located in the switch bank near the top center of the instrument panel. Press the switch to turn on the Hazard W arning flasher . When the switch is activated, all directional turn signals will flash on and of f to warn oncoming traffic of an emergency . Press the switch a second time to[...]

CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (1 16°C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–110°C). If the pointer remains at 240°F (1 16°C) or greater an[...]

TIREFIT Storage The TIREFIT kit is located in the trunk. TIREFIT Kit Components and Operation 1. Sealant Bottle 2. Deflation Button — If Equipped 3. Pressure Gauge 4. Power Button TIREFIT Location 322 WHA T TO DO IN EMERGENCIES I n f o r m a t i o n P r o v i d e d b y :[...]

5. Mode Select Knob 6. Sealant Hose (Clear with Y ellow Cap) 7. Air Pump Hose (Black) 8. Power Plug Using the Mode Select Knob and Hoses Y our TIREFIT kit may be equipped with either of the following symbols to indicate the air or sealant mode. Selecting Air Mode T urn the Mode Select Knob (5) to this position for air pump operation only . Use the [...]

TIREFIT Usage Precautions • Replace the TIREFIT Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed on the bottle label) to assure optimum operation of the sys- tem. Refer to “Sealing a T ir e with TIREFIT” section (F) “Sealant Bottle and Hose Replacement”. • The Sealant Bottle (1) and Sealant Hose (6) is a one[...]

W ARNING! (Continued) • Do not use TIREFIT or drive the vehicle under the following circumstances: − If the cut or puncture in the tire tread is approxi- mately 0.24 in. (6 mm) or larger . − If the tire has any sidewall damage. − If the tire has any damage from driving with extremely low tire pressure. − If the tire has any damage from dr[...]

W ARNING! (Continued) • TIREFIT Sealant solution contains latex. In case of allergic reaction or rash, consult a physician im- mediately . Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water . Do not induce vomiting! Consult a physician immedi- ately . • Use the gloves prov[...]

3. Uncoil the Sealant Hose (6) and then remove the yellow cap from the fitting at the end of the hose. 4. Place the TIREFIT kit flat on the ground next to the deflated tire. 5. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem. 6. Uncoil the Power Plug (8) and then insert the plug i[...]

2. Connect the Power Plug (8) to a dif ferent 12 V olt power outlet in your vehicle or another vehicle, if avail- able. Make sure the engine is running before turning ON the TIREFIT kit. 3. The Sealant Bottle (1) may be empty due to previous use. Call for assistance. NOTE: If the Mode Select Knob (5) is on air mode and pump is operating, air will d[...]

If the tire inflates to the recommended pressure or is at least 26 psi (1.8 Bar) pressure within 15 minutes: 1. Press the Power Button (4) to turn off the TIREFIT kit. 2. Remove the Speed Limit sticker from the top of the Sealant Bottle (1) and place the sticker on the instrument panel. 3. Immediately disconnect the Sealant Hose (6) from the valve [...]

W ARNING! TIREFIT is not a permanent flat tire repair . Have the tire inspected and repaired or replaced after using TIREFIT . Do not exceed 55 mph (88 km/h) until having the tire repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you. (E) After Securing T[...]

5. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized dealer as soon as possible. Refer to “(F) Sealant Bottle and Hose Replacement.” NOTE: When having the tire serviced advise the autho- rized dealer or service center that the tire has been sealed using the TIREFIT service kit. (F) Sealant Bottle and Hose Replaceme[...]

JUMP-ST ARTING PROCEDURES If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedur es in this section carefully . NOTE: When using a portable battery boost[...]

Remote Battery Posts W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. Y ou could be seriously injured. •[...]

3. If using another vehicle to jump-start the battery , park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF . W ARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure W ARNING! Failure to follow this [...]

W ARNING! Do not connect the cable to the negative post (-) of the discharged battery . The resulting electrical spark could cause the battery to explode and could result in personal injury . 5. Start the engine in the vehicle that has the booster battery , let the engine idle a few minutes, and then start the engine in the vehicle with the dischar[...]

FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between RE- VERSE and DRIVE. Using minimal accelerator pedal pressur e to maintain the rocking motion, without spin- ni[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck and do not[...]

V ehicles equipped with A WD can be towed with the transmission in NEUTRAL and the rear wheels OFF the ground (or the rear driveshaft removed) with no limita- tion on speed or distance. CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • If the transmission is [...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 6.1L ............. 3 4 1 䡵 Onboard Diagnostic System — OBD II ...... 3 4 2 ▫ Loose Fuel Filler Cap ................. 3 4 2 䡵 Emissions Inspection And Maintenance Programs ............................ 3 4 3 䡵 Replacement Parts ..................... 3 4 4 䡵 Dealer Service .....[...]

▫ Cooling System ..................... 3 5 8 ▫ Brake System ....................... 3 6 3 ▫ Automatic T ransmission ............... 3 6 5 ▫ Rear Axle .......................... 3 6 7 ▫ Appearance Care And Protection From Corrosion .......................... 3 6 8 䡵 Fuses .............................. 3 7 3 ▫ Integrated Power Module .[...]

ENGINE COMP ARTMENT — 6.1L 1 — Remote Jump Start (Positive Battery Post) 6 — Power Steering Fluid Reservoir 2 — Integrated Power Module 7 — Air Cleaner Filter 3 — Coolant Pressure Cap 8 — Engine Oil Fill 4 — Brake Fluid Reservoir Access Cover 9 — Engine Oil Dipstick 5 — Engine Coolant Reservoir 10 — W asher Fluid Reservoir 7 M[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly , your vehicle will provide excellent performance and fuel economy , as well[...]

TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehic[...]

4. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and [...]

NOTE: Intentional tampering with emissions control systems may void your warranty and could r esult in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perfo[...]

Engine Oil Checking Oil Level T o assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut of f or before starting the engine after it has sat overn[...]

CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New V ehicle Limited W arranty . Engine Oil V iscosity (SAE Grade) SAE 5W -40 engine oil is preferred for use in all operating temperatures. The engine oil filler cap also shows the recommended engine oil viscosity for [...]

Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter . Use a filter of this type for replacement. The quality of replacement filters varies considerably . Only high quality filters should be used to assure m[...]

Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably . Only high quality filters should be used to assure most efficient service. MOP AR 威 engine air cleaner filters are a high quality filter and are recommended. Maintenance-Free Battery Y our vehicle is equipped with a maintenance-fr ee ba[...]

W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water . • Battery gas is flammable and explosive. Kee[...]

Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. CAUTION! Do not use chemical flushes in yo[...]

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor o- carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving pr oduct. How- ever , the manufacturer r ecommends that air conditioning service be performed by authorized dealers or other service facilities using r ecovery and r ec[...]

2. Slide the lid on the filter adapter forward and down and remove the used filter . 3. Install the new filter with arrows pointing in the direction of airflow , which is towar d the rear of the vehicle (text and arrows on the filter will indicate this). Refer to “Maintenance Schedule” for the proper mainte- nance intervals. A/C Air Filter 7 MA[...]

Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease, such as MOP AR 威 Spray White Lube or equivalent to assure quiet, easy operation and to protect against rust [...]

present please proceed to clean wiper blades with humid cloth removing any debris that may be affecting its function. Adding Washer Fluid The windshield washer fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent ([...]

have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil c[...]

CAUTION! (Continued) • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly . Continued operation of your vehicle with a severe malfunction could ca[...]

Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at any time the ignition switch is in the ON position. • Y ou or others can be badly burned by hot engine coolant (antifreeze) or steam from yo[...]

Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to “Maintenance[...]

Adding Coolant Y our vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement. T o prevent reducing this extended mainte- nance period, it is important that you use the same engine coo[...]

Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. W ARNING! • The w[...]

Coolant Level The coolant bottle provides a quick visual method for determining that the engine coolant (antifreeze) level is adequate. W ith the engine OFF and cold, the level of the engine coolant (antifreeze) in the bottle should be be- tween the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need t[...]

• If frequent engine coolant (antifreeze) additions ar e requir ed, or if the level in the coolant recovery bottle does not dr op when the engine cools, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at 50% HOA T engine coolant (antifreeze) (minimum) and distilled water for proper co[...]

Master Cylinder – Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system fail- ure. Check the fluid level in the master cylinder when per- forming underhood services. Clean the top of the master cylinder area before r emoving the cap. Add fluid to bring the level up to t[...]

W ARNING! (Continued) • T o avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container . Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil un[...]

CAUTION! • Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Ge[...]

Special Additives Automatic T ransmission Fluid (A TF) is an engineered product and its performance may be impair ed by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers[...]

Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your v[...]

• Use a high quality cleaner wax, such as MOP AR 威 Cleaner W ax to remove road film, stains and to protect your paint finish. T ake care never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! • Do not use abrasive or strong cleaning materials such as[...]

• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use MOP AR 威 T ouch Up Paint or equivalent on scratches as soon as possible. Y our authorized dealer has [...]

• Do not use any harsh solvents or any other form of protectants on Stain Repel products. Interior Care Use MOP AR 威 Fabric Cleaner or equivalent to clean fabric upholstery and MOP AR 威 Carpet Cleaner or equivalent for carpeting. Interior trim should be cleaned starting with a damp cloth, or MOP AR 威 Satin Select or equivalent. Do not use h[...]

T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleane[...]

Replace the belts if they appear frayed or worn or if the buckles do not work properly . Cleaning the Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed. FUSES Integrated Power Module The Integrated Power Module (IPM) is located in the eng[...]

CAUTION! • When installing the integrated power module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the [...]

Cavity Car- tridge Fuse Mini- Fuse Description 8 — 30 Amp Green Starter 9 ——— 10 30 Amp Pink — W indshield W iper 1 1 30 Amp Pink — Anti-Lock Brake System (ABS) V alves 12 40 Amp Green — Radiator Fan 13 50 Amp Red — Anti-Lock Brake System (ABS) Pump Motor 1 4——— Cavity Car- tridge Fuse Mini- Fuse Description 15 50 Amp Red — [...]

Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays. Opening the Access Panel Rear Power Distribution Center 376 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

CAUTION! • When installing the power distribution center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having [...]

Cavity Car- tridge Fuse Mini- Fuse Description 5 30 Amp Pink — Heated Seats – If Equipped 6 — 20 Amp Y ellow Fuel Pump 7 — 20 Amp Y ellow Sub Amp – If Equipped 8 — 15 Amp Blue Diagnostic Link Connec- tor (DLC)/W ireless Con- trol Module (WCM)/ W ireless Ignition Node (WIN) 9 — 20 Amp Y ellow Power Outlet 1 0——— 11 * ——— 12[...]

Cavity Car- tridge Fuse Mini- Fuse Description 2 3——— 2 4——— 2 5——— 2 6——— 27 — 10 Amp Red Occupant Restraint Con- troller (ORC) 28 — 10 Amp Red Ignition Run 29 — 5 Amp Orange Cluster/Electronic Sta- bility Program (ESP)/ Powertrain Control Module (PCM)/Stop Light Switch 30 — 10 Amp Red Door Modules/Power Mirrors/Ste[...]

Cavity Car- tridge Fuse Mini- Fuse Description 38 — 10 Amp Red Cargo Light/Satellite Receiver (SDARS) V ideo – If Equipped/V ehicle Information Module – If Equipped 39 — 10 Amp Red Heated Mirrors – If Equipped 40 — 5 Amp Orange Auto Inside Rearview Mirror/Heated Seats – If Equipped/Switch Bank 4 1——— 42 30 Amp Pink — Fr ont Bl[...]

VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery . • Disconnect the negative cable from the battery . • Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five mi[...]

Exterior Bulb Number Low Beam Headlamp (Standard Halogen) ...... 9006 Low Beam Headlamp – High Intensity Discharge (HID) .............. D 1 S (Serviced at Authorized Dealer) High Beam Headlamp .................... 9005 Front Park/T urn Lamp ................... 3157A Front Fog Lamp – If Equipped ............ PSX24W Front Side Marker ............[...]

CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 4. Reinstall the bulb and socket assembly into the head- lamp assembly , an[...]

3 — Park/T urn Lamp Bulb 4 — Side Marker Lamp Bulb 384 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

Low Beam Headlamp, High Beam Headlamp, and Park/T urn Lamp — Models with High Intensity Discharge Headlamps (HID) HID Headlamps The headlamps are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlamp switch off and the key removed. Because of this, you should not attempt to service a headlamp bulb yo[...]

Backup Lamp, Side Marker Lamp, T ail/T urn Lamp, and T ail/Stop Lamp 1. Open the trunk. 2. Remove two fasteners from the back of the taillamp assembly . 3. Pull back the trunk liner . 4. Remove the remaining fastener from the back of the taillamp assembly . 5. Push the electrical connector locking tab to the side. 6. Disconnect the electrical conne[...]

8. T urn the appropriate bulb and socket assembly coun- terclockwise to remove it from the taillamp assembly . 1 — Backup Lamp Bulb 2 — Side Marker Lamp Bulb 7 MAINT AINING YOUR VEHICLE 387 I n f o r m a t i o n P r o v i d e d b y :[...]

9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the taillamp assembly , and then turn it clockwise. 3 — T ail/T urn Lamp Bulb 4 — T ail/Stop Lamp Bulb 388 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

1 1. Reinstall the taillamp assembly , fasteners, electrical connector , and trunk liner . 12. Close the trunk. License Lamp 1. Remove the scr ews securing the lamp to the r ear fascia. 2. Remove the bulb and socket assembly . 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 4. Reinstall the bulb and socket assembly[...]

FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 19 Gallons 72 Liters Engine Oil with Filter 6.1 Liter Engine (SAE 5W -40, API Certified) 7 Quarts 6.6 Liters Cooling System * 6.1 Liter Engine (MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula or equivalent) 15.2 Quarts 14.4 Liters * Includes heater and coolant recovery bottle filled to MAX[...]

FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hy- brid Organic Additive T echnology) or equivalent. Engine Oil For best performance and maximum protection under all types of operat- ing conditions, the manufacturer only recom[...]

Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. Brake Master Cylinder MOP AR 威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recom- mended brake fl[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance ...... 3 9 4 䡵 Maintenance Schedule .................. 3 9 4 ▫ Required Maintenance Intervals .......... 3 9 6 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e d b y :[...]

EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions contr ol system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliabilit[...]

NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Un[...]

• Check the fluid levels of the coolant reservoir , brake master cylinder , and power steering, add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in [...]

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tire[...]

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and[...]

30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 36,000 Mil[...]

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate ti[...]

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil an[...]

66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate[...]

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate [...]

90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Inspect and replace the PCV V alve if necessary .* ❏ Inspect the rear axle fluid. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. Odomete[...]

102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the spark plugs. ❏ Flush and replace the engine coolant if not done at 60 months. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 108,000 Miles (180,000 km) or [...]

1 14,000 Miles (190,000 km) or 1 14 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ R[...]

126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine o[...]

138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rot[...]

* This maintenance is r ecommended by the manufactur er to the owner , but is not required to maintain emissions warranty . W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, ta[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 1 3 ▫ Prepare For The Appointment ........... 4 1 3 ▫ Prepare A List ...................... 4 1 3 ▫ Be Reasonable W ith Requests ............ 4 1 3 䡵 If Y ou Need Assistance ................. 4 1 3 ▫ Chrysler[...]

䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 1 8 ▫ T readwear ......................... 4 1 9 ▫ T raction Grades ..................... 4 1 9 ▫ T emperature Grades .................. 4 1 9 412 IF YOU NEED CONSUMER ASSIST ANCE I n f o r m a t i o n P r o v i d e d b y :[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty . Discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • If an authorized dealership is unable to resolv[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center . Any hearing or speech impaired customer , who has access to a TDD or a conventional teletypewriter (TTY) in the[...]

W e appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. Y ou’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. W[...]

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However , NHTSA cannot become involved in individual problems between you, your authorized dealer , and the manufacturer . T o contact NHTSA, you may either call the Auto [...]

• Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features. They show exactly how to find and corr ect problems the first time, using st[...]

T readwear The T readwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual c[...]

V ehicle Safety Standard No. 109. Grades B and A repr e- sent higher levels of performance on the laboratory test wheel, than the minimum requir ed by law . W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately[...]

INDEX 10 I n f o r m a t i o n P r o v i d e d b y :[...]

About Y our Brakes .................... 270,272 ABS (Anti-Lock Brake System) ............ 273,276 Adding Engine Coolant (Antifreeze) .......... 3 6 0 Adding Fuel ........................... 3 1 2 Adding W asher Fluid ..................... 3 5 5 Additives, Fuel ......................... 3 1 0 Adjustable Pedals ....................... 1 4 0 Air Clean[...]

Automatic Door Locks ................... 27,28 Automatic Headlights .................... 1 3 1 Automatic T emperature Control (A TC) ......... 2 4 0 Automatic T ransaxle Special Additives ...................... 3 6 7 Automatic T ransmission ............. 260,365,366 Adding Fluid ...................... 366,392 Autostick ............................ [...]

Brightness, Interior Lights .................. 1 3 5 Bulb Replacement ..................... 381,382 Bulbs, Light .......................... 78,381 Calibration, Compass ..................... 1 8 9 Capacities, Fluid ........................ 3 9 0 Caps, Filler Fuel ............................... 3 1 2 Oil (Engine) .......................... 3 4 7 Pow[...]

Console, Floor .......................... 1 5 9 Console, Overhead ....................... 1 4 5 Contract, Service ........................ 4 1 5 Coolant Pressure Cap (Radiator Cap) .......... 3 6 1 Cooling System ......................... 3 5 8 Adding Coolant (Antifreeze) .............. 3 6 0 Coolant Capacity ...................... 3 9 0 Coolant Le[...]

Door Locks ............................. 2 6 Door Locks, Automatic .................... 2 7 Door Opener , Garage ..................... 1 4 6 Driving On Slippery Surfaces ................... 2 6 5 Through Flowing, Rising, or Shallow Standing W ater ........................ 2 6 6 DVD Player (V ideo Entertainment System™) .... 2 3 5 Electric Rear W [...]

Fuel Requirements ..................... 3 0 8 Jump Starting ......................... 3 3 2 O i l ........................... 346,390,391 Oil Change Interval .................... 3 4 6 Oil Filler Cap ......................... 3 4 7 Oil Filter ............................ 3 4 8 Oil Filter Disposal ..................... 3 4 7 Oil Selection ..........[...]

Brake .............................. 3 6 4 Cooling System ....................... 3 5 8 Engine Oil ........................... 3 4 6 Power Steering ........................ 2 6 9 Fluids ................................ 3 9 1 Fluids, Lubricants and Genuine Parts .......... 3 9 1 Fog Lights .......................... 133,172 Folding Rear Seat .......[...]

General Maintenance ..................... 3 4 5 Glass Cleaning .......................... 3 7 2 Gross Axle W eight Rating .................. 3 1 5 Gross V ehicle W eight Rating ................ 3 1 5 GVWR ............................... 3 1 5 Hands-Free Phone (Uconnect™) .............. 8 7 Hazard Driving Through Flowing, Rising, or Shallow Standi[...]

Immobilizer (Sentry Key) ................... 1 5 Infant Restraint ........................ 64,65 Information Center , V ehicle ................. 1 7 8 Inside Rearview Mirror .................... 8 3 Instrument Cluster .................... 167,168 Instrument Panel and Controls .............. 1 6 6 Instrument Panel Lens Cleaning ............. 3 7 2 I[...]

Anti-Lock ......................... 177,275 Automatic Headlights ................... 1 3 1 Brake Assist W arning ................... 2 8 1 Brake W arning ..................... 173,272 Bulb Replacement ................... 381,382 Courtesy/Reading ................... 134,145 Cruise .............................. 1 6 8 Daytime Running ................[...]

T ire Pressur e Monitoring (TPMS) ........ 175,301 T raction Control ....................... 2 8 1 T urn Signal ................... 78,133,134,170 V anity Mirror .......................... 8 7 V oltage ............................. 1 6 8 W arning (Instrument Cluster Description) ..... 1 6 8 Loading V ehicle ...................... 315,316 Capacities[...]

Exterior Folding ........................ 8 5 Heated .............................. 8 6 Outside .............................. 8 4 Rearview ............................. 8 3 V anity ............................... 8 7 Modifications/Alterations, V ehicle ............. 7 Monitor , T ir e Pressure System ............... 3 0 1 Mopar Parts .............[...]

Outside Rearview Mirrors .................. 8 4 Overhead Console ....................... 1 4 5 Overheating, Engine ...................... 3 2 0 Owner’s Manual (Operator Manual) ......... 4,417 Paint Care ............................. 3 6 8 Panic Alarm ............................ 2 1 Parking Brake .......................... 2 7 0 Passing Light ..[...]

Radio, Satellite (Uconnect 威 studios) ........... 2 2 9 Rear Cupholder ......................... 1 5 9 Rear Seat, Folding ....................... 1 2 7 Rear W indow Defroster ................... 1 6 2 Rear W indow Features .................... 1 6 2 Rearview Mirrors ........................ 8 3 Reclining Front Seats ..................... 1 2 3 Re[...]

Schedule, Maintenance .................... 3 9 4 Seat Belt Maintenance .................... 3 7 2 Seat Belt Reminder ....................... 4 6 Seat Belts .......................... 37,39,76 Adjustable Upper Shoulder Anchorage ........ 4 4 And Pregnant W omen ................... 4 8 Child Restraint ................... 64,65,66,71 Extender ........[...]

Settings, Personal ........................ 1 9 2 Shifting ............................... 2 5 6 Automatic T ransmission .............. 256,260 Shoulder Belt Upper Anchorage .............. 4 4 Shoulder Belts ........................... 3 9 Signals, T urn ...................... 78,134,170 Slippery Surfaces, Driving On ............... 2 6 5 Snow T ir[...]

Synthetic Engine Oil ...................... 3 4 7 System, Remote Starting .................... 2 3 T achometer ............................ 1 6 8 T elescoping Steering Column ............... 1 3 9 T emperatur e Control, Automatic (A TC) ........ 2 4 0 T emperatur e Gauge, Engine Coolant ....... 169,321 T ether Anchor , Child Restraint .............[...]

T owing ............................... 3 1 7 24-Hour T owing Assistance ............... 1 0 2 Behind a Motor Home .................. 3 1 7 Disabled V ehicle ....................... 3 3 7 Recreational .......................... 3 1 7 T owing Assistance ....................... 1 0 2 T owing V ehicle Behind a Motor Home ......... 3 1 7 T raction Cont[...]

V ehicle Identification Number (VIN) ............ 6 V ehicle Loading ................... 289,315,316 V ehicle Modifications/Alterations .............. 7 V ehicle Storage ....................... 246,381 V ehicle Theft Alarm (Security Alarm) .......... 1 7 V ideo Entertainment System™ (Rear Seat V ideo System) .................. 2 3 5 V iscosity , [...]

Chrysler Group LLC 10D482-126-AC 3rd Edition Printed in U.S.A. I n f o r m a t i o n P r o v i d e d b y :[...]