Draytek Vigor 2925 manuel d'utilisation

[...]

Vigor2925 Series User’s Guide ii[...]

Vigor2925 Series User’s Guide iii Vigor2925 Series Dual-WAN Security Router User’s Guide Version: 1.3 Firmware Version: V3.7.3 (For future update, please visit Dray Tek web site) Date: 29/10/2013[...]

Vigor2925 Series User’s Guide iv Copyright Information Copyright Declarations Copyright 2013 All rights reserved. This pub lication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stor ed in a retrieval system, or translated into any language withou t written permission from the copyright [...]

Vigor2925 Series User’s Guide v European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, H ukou Township , Hsinchu In dustrial Park, Hsi nchu County, Tai wan 303 Product: Vigor2925 Ser ies Router DrayTek Corp. declares that Vigor2925 Series of ro uters are in compliance with the following essential requirements [...]

Vigor2925 Series User’s Guide vi[...]

Vigor2925 Series User’s Guide vii T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s Introduction................................................................................................... 1 1.1 Web Conf iguration Buttons Explanation ................................................................................. 2 1.2 LED Indic[...]

Vigor2925 Series User’s Guide viii 3.5 How to Optimize the Bandwidth through QoS T e chnology ................................................... 68 3.6 QoS Setting Example ........................................................................................................ .... 72 3.7 How to use Landing Page Feature ..........................[...]

Vigor2925 Series User’s Guide ix 4.6.4 DoS Defense .............................................................................................................. .. 213 4.7 User Management............................................................................................................... 217 4.7.1 General Setup ........................[...]

Vigor2925 Series User’s Guide x 4.13.2 Trusted CA Certificate ................................................................................................ 341 4.13.3 Certificate Backup ...................................................................................................... . 342 4.14 Wireless LAN ................................[...]

Vigor2925 Series User’s Guide xi 4.19 External Devices .......................................................................................................... ..... 418 4.19.1 All Devices .................................................................................................................. 418 4.19.2 Access Point Devices ..........[...]

[...]

Vigor2925 Series User’s Guide 1 I I n n t t r r o o d d u u c c t t i i o o n n Vigor2925 series is a VDSL2 router. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, the router increases the performanc[...]

Vigor2925 Series User’s Guide 2 1 1 . . 1 1 W W e e b b C C o o n n f f i i g g u u r r a a t t i i o o n n B B u u t t t t o o n n s s E E x x p p l l a a n n a a t t i i o o n n Several main buttons appeared on the web pages are defined as the following: Save and apply current settings. Cancel current settings and recover to the previous saved [...]

Vigor2925 Series User’s Guide 3 1 1 . . 2 2 L L E E D D I I n n d d i i c c a a t t o o r r s s a a n n d d C C o o n n n n e e c c t t o o r r s s Before you use the Vigor router, please get acquainted with the LED indicators and connectors first. 1 1 . . 2 2 . . 1 1 F F o o r r V V i i g g o o r r 2 2 9 9 2 2 5 5 LED Status Explanation Blinking[...]

Vigor2925 Series User’s Guide 4 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. US[...]

Vigor2925 Series User’s Guide 5 1 1 . . 2 2 . . 2 2 F F o o r r V V i i g g o o r r 2 2 9 9 2 2 5 5 n n LED Status Explanation Blinking The router is powered on and running normally. ACT (Activity) Off The router is powered off. On USB device is connected and ready for use. USB Blinking The data is transmitting. On Wireless access point is ready.[...]

Vigor2925 Series User’s Guide 6 Interface Description Wireless LAN ON/OFF/WPS Press "Wireless LAN ON/OFF/WPS" button once to wait for client device making network connection through WPS. Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the[...]

Vigor2925 Series User’s Guide 7 1 1 . . 3 3 H H a a r r d d w w a a r r e e I I n n s s t t a a l l l l a a t t i i o o n n Before starting to configure the router, you have to connect your devices correctly. 1. Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router with Ethernet cable (RJ-45). 2. Connect one end of an Ethern[...]

Vigor2925 Series User’s Guide 8 1 1 . . 4 4 P P r r i i n n t t e e r r I I n n s s t t a a l l l l a a t t i i o o n n You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please vi[...]

Vigor2925 Series User’s Guide 9 3. Open File->Add Printer . A welcome dialog will appear. Please click Next . 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port . Click Next .[...]

Vigor2925 Series User’s Guide 10 6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next . 7. Click Standard and choose Generic Network Card. 8. Then, in the following dialog, click Finish .[...]

Vigor2925 Series User’s Guide 11 9. Now, your system will ask you to choose right na me of the printer t hat you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next . 10. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new [...]

Vigor2925 Series User’s Guide 12 The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional func tions are not supported. If you do not know whether your printer is supported or not, please visit www.draytek.com to fi[...]

Vigor2925 Series User’s Guide 13 B B a a s s i i c c S S e e t t t t i i n n g g s s For using the router properly, it is necessary for you to change the password of web configuration for security and adjust primary basic settings. This chapter explains how to setup a password for accessing into the web user interface of Vigor router and how to a[...]

Vigor2925 Series User’s Guide 14 4. Now, the Main Screen will appear. Note: The home page will be different slightly in accordance with the ty pe of the router you have. 5. The web page can be logged out according to the chosen condition. The default setting is Auto Logout , which means the web configuration system will logout after 5 m inutes wi[...]

Vigor2925 Series User’s Guide 15 2 2 . . 2 2 C C h h a a n n g g i i n n g g P P a a s s s s w w o o r r d d Please change the password for the or iginal security of the router. 1. Open a web browser on your PC and type http://192. 168.1.1. A pop-up window will open to ask for username and password. 2. Please type “admin/admin” as Username/Pa[...]

Vigor2925 Series User’s Guide 16 2 2 . . 3 3 Q Q u u i i c c k k S S t t a a r r t t W W i i z z a a r r d d If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickl y. The first screen of Quick Start Wizard is entering login password. After ty ping the passwor[...]

Vigor2925 Series User’s Guide 17 2 2 . . 3 3 . . 1 1 F F o o r r W W A A N N 1 1 / / W W A A N N 2 2 ( ( E E t t h h e e r r n n e e t t ) ) WAN1/WAN2 is dedicated to physical mode in Ethernet. If you choose WAN1/WAN2, please specify physical type. Then, click Next . On the next page as shown below, please select the appropriate Internet access t[...]

Vigor2925 Series User’s Guide 18 2. Click PPPoE as the Internet Access Type. Then click Next to continue. Available settings are explained as follows: Item Description User Name Assign a specific valid user name provided by the ISP. Note: The maximum length of the user name you can set is 63 characters. Password Assign a valid password provided b[...]

Vigor2925 Series User’s Guide 19 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet. P P P P T T P P / / L L 2 2 T T P P 1. Choose WAN2 as the WAN Interface and click the Next button. The following page will be open for you to[...]

Vigor2925 Series User’s Guide 20 2. Click PPTP/L2TP as the Internet Access Type. Then click Next to continue. Available settings are explained as follows: Item Description User Name Assign a specific valid user name provided by the ISP. Note: The maximum length of the user name you can set is 63 characters. Password Assign a valid password provid[...]

Vigor2925 Series User’s Guide 21 3. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Inte[...]

Vigor2925 Series User’s Guide 22 2. Click Static IP as the Internet Access type. Simply click Next to continue. Available settings are explained as follows: Item Description WAN IP Type the IP address. Subnet Mask Type the subnet mask. Gateway Type the IP address of gateway. Primary DNS Type in the primary IP address for the router. Secondary DNS[...]

Vigor2925 Series User’s Guide 23 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet. D D H H C C P P 1. Choose WAN2 as WAN Interface and click the Next button. The following page will be open for you to specify Internet Access[...]

Vigor2925 Series User’s Guide 24 39 characters. MAC Some Cable service providers specify a specific MAC address for access authentication. In such cases you need to enter the MAC address. Back Click it to return to previous setting page. Next Click it to get into the next setting page. Cancel Click it to give up the quick start wizard. 3. After f[...]

Vigor2925 Series User’s Guide 25 2 2 . . 3 3 . . 2 2 F F o o r r W W A A N N 3 3 ( ( U U S S B B ) ) WAN3 is dedicated to physical mode in USB. If WAN3 is selected, it is not necessary for you to type any information for such connection. 1. Choose WAN3 as WAN Interface. 2. Then, click Next for getting the following page. Available settings are ex[...]

Vigor2925 Series User’s Guide 26 APN Name – APN means Access Point Name which is provided and required by some ISPs. Type the name and click Apply . 3. Then, click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, yo[...]

Vigor2925 Series User’s Guide 27 2 2 . . 4 4 S S e e r r v v i i c c e e A A c c t t i i v v a a t t i i o o n n W W i i z z a a r r d d Service Activation Wizard can guide you to activate WCF service (Web Content Filter) with a quick and easy way. For the Service Activation Wizard is only available for admin operation, therefore, please type “[...]

Vigor2925 Series User’s Guide 28 3. In the following page, you can activate the Web content filter services at the same time or individually. When you finish the selection, please click Next . Commtouch is the web content filter based on Commtouch operated in the worldwide. There is a 30-day trial period. After trial, you can purchase DrayTek&apo[...]

Vigor2925 Series User’s Guide 29 5. Wait for a moment till the following page appears. When such page appears, you can enable or disable these services for your necessity. Then, click Finish. Note: The service will be activated and applied as the default rule configured in Firewall>>General Setup . 6. Now, the web page will display the serv[...]

Vigor2925 Series User’s Guide 30[...]

Vigor2925 Series User’s Guide 31 2 2 . . 5 5 W W i i r r e e l l e e s s s s W W i i z z a a r r d d The wireless wizard allows you to configure se ttings specified for a host AP (for home use or internal use for a company) and specified fo r a guest AP (for any wireless clients accessing into Internet). Follow the steps listed below: 1. Open Wir[...]

Vigor2925 Series User’s Guide 32 Channel Means the channel of frequency of the wireless LAN. The default channel is 6. You may switch channel if the selected channel is under serious interference. If you have no idea of choosing the frequency, please select Auto to let system determine for you. Password The wireless mode offered by this wizard is[...]

Vigor2925 Series User’s Guide 33 Password The wireless mode offered by this wizard is WPA2/PSK. The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Either 8~63 ASCII characters, such as 012345678(or 64 He[...]

Vigor2925 Series User’s Guide 34 2 2 . . 6 6 I I n n t t r r o o d d u u c c i i n n g g D D a a s s h h b b o o a a r r d d Dashboard shows the connection status including Sy stem Information, IPv4 Internet Access, IPv6 Internet Access, Interface (physical c onnection), Security and Quick Access. Click Dashboard from the main menu on the left si[...]

Vigor2925 Series User’s Guide 35 2 2 . . 6 6 . . 1 1 V V i i r r t t u u a a l l P P a a n n e e l l On the top of the Dashboard, a virtual panel (sim ulating the physical panel of the router) displays the physical interface connection. It will be refreshed every five seconds. Port Color Displayed Explanation Black It means such port is disconnec[...]

Vigor2925 Series User’s Guide 36 2 2 . . 6 6 . . 3 3 Q Q u u i i c c k k A A c c c c e e s s s s f f o o r r C C o o m m m m o o n n U U s s e e d d M M e e n n u u All the menu items can be accessed and arranged orderly on the left side of the main page for your request. However, some important and common used menu items which can be accessed in[...]

Vigor2925 Series User’s Guide 37 Host connected physically to the router via LAN port(s) will be displayed with green circles in the field of Connected. All of the hosts (including wireless clients) displayed with Host ID, IP Address and MAC address indicates that the traffic would be transmitted through LAN port(s) and then the WAN port. The pur[...]

Vigor2925 Series User’s Guide 38 2 2 . . 6 6 . . 5 5 W W e e b b C C o o n n s s o o l l e e It is not necessary to use the telnet command via DOS prompt. The changes made by using web console have the same effects as m odified through web user interface. The functions/settings modified under Web Consol e also can be reviewed on t he web user int[...]

Vigor2925 Series User’s Guide 39 2 2 . . 6 6 . . 6 6 C C o o n n f f i i g g B B a a c c k k u u p p There is one way to store current used settings quickly by clicking the Config Backup icon. It allows you to backup current settings as a file. Such configuration file can be restored by using System Maintenance>>Configuration Backup . Simpl[...]

Vigor2925 Series User’s Guide 40 2 2 . . 7 7 O O n n l l i i n n e e S S t t a a t t u u s s 2 2 . . 7 7 . . 1 1 P P h h y y s s i i c c a a l l C C o o n n n n e e c c t t i i o o n n Such page displays the physical connection status such as LAN connection status, WAN connection status, ADSL information, and so on. P P h h y y s s i i c c a a l [...]

Vigor2925 Series User’s Guide 41 Detailed explanation (for IPv4) is shown below: Item Description LAN Status Primary DNS- Displays the primary DNS server address for WAN interface. Secondary DNS - Displays the secondary DNS server address for WAN interface. IP Address -Displays the IP address of the LAN interface. TX Packets -Displays the total t[...]

Vigor2925 Series User’s Guide 42 Item Description Mode - Displays the type of WAN connection (e.g., TSPC). Up Time - Displays the total uptime of the interface. IP - Displays the IP address of the WAN interface. Gateway IP - Displays the IP address of the default gateway. Note: The words in green mean that the WAN connection of that interface is [...]

Vigor2925 Series User’s Guide 43 2 2 . . 9 9 R R e e g g i i s s t t e e r r i i n n g g V V i i g g o o r r R R o o u u t t e e r r You have finished the configuration of Quick Start Wizard and you can surf the Internet at any time. Now it is the time to register your Vigor router to MyVigor website for getting more service. Please follow the st[...]

Vigor2925 Series User’s Guide 44 4 The following page will be displayed after you logging in MyVigor. From this page, please click Add or Product Registration . 5 When the following page appears, please type in Nickname (for the router) and choose the right registration date from the popup calendar (it appears when you click o n the box of Regist[...]

Vigor2925 Series User’s Guide 45 6 When the following page appears, your r outer information has been added to the database. 7 Now, you have finished the product registration. 8 After clicking OK , you will see the following page. Your router has been registered to myvigor website successfully. If you have not activated web content filter service[...]

Vigor2925 Series User’s Guide 46 11 When this page appears, click Register . 12 Wait for a moment until the following page appears. 13 Click Close .[...]

Vigor2925 Series User’s Guide 47 T T u u t t o o r r i i a a l l s s a a n n d d A A p p p p l l i i c c a a t t i i o o n n s s 3 3 . . 1 1 H H o o w w t t o o c c o o n n f f i i g g u u r r e e s s e e t t t t i i n n g g s s f f o o r r I I P P v v 6 6 S S e e r r v v i i c c e e i i n n V V i i g g o o r r 2 2 9 9 2 2 5 5 Due to the shortage[...]

Vigor2925 Series User’s Guide 48 Note: Only one WAN interface support IPv6 service at one time. In this example, WAN2 is chosen as the one supporting IPv6 service. 2. In the following figure, use the drop down list to choo se a proper connection type. Different connection types will bring out different configuration page. Refer to the following: [...]

Vigor2925 Series User’s Guide 49 Click OK and open Online Status . If the connection is successful, you will get the IP address for IPv4 and IPv6 at the same time.[...]

Vigor2925 Series User’s Guide 50  TSPC – Tunnel application, both IPv6 hosts communicate through IPv4 network Choose TSPC and type the information for TSPC service. Note: While using such mode, you have to ma ke sure the IPv4 network connection is normal. (In the following figure, the TSPC inform ation is obtained from http://gogo6.com/ afte[...]

Vigor2925 Series User’s Guide 51  AICCU – Tunnel application Choose AICCU and type the information for AICCU of IPv6. Note: While using such mode, you have to ma ke sure the IPv4 network connection is normal. (In the following figure, the AICCU information is obtained from https://www.sixxs.net/main/ after applied for the service.) Click OK [...]

Vigor2925 Series User’s Guide 52  DHCPv6 Client Choose DHCPv6 Client. Click one of the identity associations and type the IAID number. Click OK and open Online Status . If the connection is successful, the physical connection will be shows as follows:[...]

Vigor2925 Series User’s Guide 53  Static IPv6 Choose Static IPv6. Type IPv6 address, Prefix Length and Gateway Address. Click OK and open Online Status . If the connection is successful, the physical connection will be shows as follows:[...]

Vigor2925 Series User’s Guide 54 I I I I . . C C o o n n f f i i g g u u r r i i n n g g t t h h e e L L A A N N S S e e t t t t i i n n g g s s After finished the WAN settings for IPv6, pl ease configure the LAN settings to make the router’s client getting the IPv6 address. 1. Access into the web user interface of Viogr2925. Open LAN >> [...]

Vigor2925 Series User’s Guide 55 I I I I I I . . C C o o n n f f i i r r m m i i n n g g I I P P v v 6 6 S S e e r r v v i i c c e e R R u u n n S S u u c c c c e e s s s s f f u u l l l l y y 1. Make sure you have get the correct IPv6 IP address. Get into MS-DOS interface and type the command of “ipconfig”. Refer to the following figure. Fro[...]

Vigor2925 Series User’s Guide 56 3. Connect to the website for IPv6. Open a web browser and type an URL of IPv6, e.g., www.kame.net . If your computer accesses into the website by using IPv6 address, you may see a turtle dancing on the screen. If not, only a steady turtle will be seen. If you can see a turtle dancing on the screen, that means IPv[...]

Vigor2925 Series User’s Guide 57 3 3 . . 2 2 H H o o w w t t o o e e s s t t a a b b l l i i s s h h O O p p e e n n V V P P N N - - h h o o s s t t t t o o L L A A N N t t u u n n n n e e l l s s ( ( a a u u t t h h e e n n t t i i c c a a t t e e d d w w i i t t h h o o u u t t C C A A ) ) v v i i a a S S m m a a r r t t V V P P N N C C l l i i[...]

Vigor2925 Series User’s Guide 58 S S e e t t t t i i n n g g s s f f o o r r R R o o u u t t e e r r ( ( M M a a i i n n O O f f f f i i c c e e ) ) 1. Access into the web user interface of Vigor router. 2. Open VPN and Remote Access >> OpenVPN General Setup to configure the OpenVPN setting with disabled Certificate Authentication. Click OK[...]

Vigor2925 Series User’s Guide 59 S S e e t t t t i i n n g g s s f f o o r r P P C C ( ( R R e e m m o o t t e e U U s s e e r r ) ) 1. Execute SmartVPN Client. Click Insert to create a new dial-in VPN profile (e.g., Profile 6). 2. Type a name (e.g., Profile 6) as the Profile Name and an IP address (e.g., 200.200.200.200) as VPN Server IP. Set jo[...]

Vigor2925 Series User’s Guide 60 C C h h e e c c k k i i n n g g t t h h e e V V P P N N C C o o n n n n e e c c t t i i o o n n S S t t a a t t u u s s Now both ends (router and remote PC) are configured well. 1. Access into the web user interface of Vigor router. 2. Open VPN and Remote Access >>Connection Management to check the VPN conne[...]

Vigor2925 Series User’s Guide 61 3 3 . . 3 3 H H o o w w c c a a n n I I g g e e t t t t h h e e f f i i l l e e s s f f r r o o m m U U S S B B s s t t o o r r a a g g e e d d e e v v i i c c e e c c o o n n n n e e c c t t i i n n g g t t o o V V i i g g o o r r r r o o u u t t e e r r ? ? Files on USB storage device can be reviewed by opening [...]

Vigor2925 Series User’s Guide 62 3. Setup a user account for the FTP service by using USB Application >>USB User Management. Click Enable to enable FTP/Samba User account. Here we add a new account "user1" and assign authorities “Read”, “Write” and “List” to it. 4. Click OK to save the configuration. 5. Make sure the F[...]

Vigor2925 Series User’s Guide 63 6. When the following screen appears, it means the FTP service is running properly. 7. Return to USB Application >> USB Disk Status . The information for FTP server will be shown as below. Now, users in LAN of Vigor2925 can access into the USB storage device by typing ftp://192.168.1.1 on any browser. They c[...]

Vigor2925 Series User’s Guide 64 3 3 . . 4 4 H H o o w w t t o o B B u u i i l l d d a a L L A A N N - - t t o o - - L L A A N N V V P P N N B B e e t t w w e e e e n n R R e e m m o o t t e e O O f f f f i i c c e e a a n n d d H H e e a a d d q q u u a a r r t t e e r r v v i i a a I I P P S S e e c c T T u u n n n n e e l l ( ( M M a a i i n n[...]

Vigor2925 Series User’s Guide 65 4. Now navigate to the next section, Dial-In Settings to check PPTP, IPSec Tunnel and L2TP boxes. Check the box of Specify Remote… and type the Peer VPN Server IP (e.g., 218.242.130.19 in this case). Press the IKE Pre-Shared Key button to set the PSK ; and select Medium (AH) or High (ESP) as the security method.[...]

Vigor2925 Series User’s Guide 66 7. Open VPN and Remote Access >>Connection Management to check the dial-in connection status (from branch office). C C o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r R R o o u u t t e e r r f f o o r r B B r r a a n n c c h h O O f f f f i i c c e e 1. Log into the web user inter[...]

Vigor2925 Series User’s Guide 67 4. Now navigate to the next section, Dial-Out Settings to select the IPSec Tunnel service and type the remote server IP/host name (e.g., 218.242 .133.91, in this case). Press the IKE Pre-Shared Key button to set the PSK ; and select Medium (AH) or High (ESP) as the security method. 5. Continue to navigate to the T[...]

Vigor2925 Series User’s Guide 68 7. Open VPN and Remote Access >>Connection Management to check the dial-in connection status (from head office). 3 3 . . 5 5 H H o o w w t t o o O O p p t t i i m m i i z z e e t t h h e e B B a a n n d d w w i i d d t t h h t t h h r r o o u u g g h h Q Q o o S S T T e e c c h h n n o o l l o o g g y y Have[...]

Vigor2925 Series User’s Guide 69 4. Check the box of ACT . Click Edit to specify the local address. 5. In the pop-up window, choose Range Address as the Address Type and type the start IP address and end IP address in relational fields. Click OK to save the settings and exit the window. 6. Click OK again to save the settings.[...]

Vigor2925 Series User’s Guide 70 7. The class rule for VoIP has been set. Click OK to return to previous page. 8. Do the same steps to add class rules for IPTV and Data/Email with IP addresses as shown below. a n d[...]

Vigor2925 Series User’s Guide 71 9. Assuming you get 2MB/512Kb Internet line. You can click the Setup link of WAN1 to set up the bandwidth for different groups am ong VoIP, IPTV and Data/Email. 10. In the Setup page, check the box of Enable the QoS Control . Type 30, 50 and 15 in the boxes for VoIP, IPTV and Data/Email respectively. Check the box[...]

Vigor2925 Series User’s Guide 72 3 3 . . 6 6 Q Q o o S S S S e e t t t t i i n n g g E E x x a a m m p p l l e e Assume a teleworker someti mes works at hom e and takes care of children. When working time, he would use V igor router at home to connect to the server in the headquarter of fice downtown via either HTTPS or V PN to check email and ac[...]

Vigor2925 Series User’s Guide 73 4. Return to previous page. Enter the Name of Index Class 1 by clicking Edit link. T ype the name “ E-m ail ” for Class 1. Click OK to save the settings. 5. Click the Setup link for W AN2. The user can set reserved bandwidt h (e.g., 25%) for E-mail using protocol POP3 and SMTP . Click OK to save the settings. [...]

Vigor2925 Series User’s Guide 74 7. Click Setup link for W AN2. 8. Check Enable UDP Bandwidth Contr ol on the bottom to prevent enorm ous UDP traffic influent other application. Click OK . 9. If the worker has connected to the headquarter using host to host VPN tunnel. (Please refer to Chapter 3 VPN for detail instruction), he m ay set up an inde[...]

Vigor2925 Series User’s Guide 75 10. Click Edit for Class 3 to open a new window . In this index, the user will set reserved bandwidth for VPN . 11. Click Add to open the following window . Check the ACT box, first. 12. Then click Edit of Local Address to set a worker ’ s subnet address. Click Edit of Remote Address to set headquarter ’ s IP [...]

Vigor2925 Series User’s Guide 76 3 3 . . 7 7 H H o o w w t t o o u u s s e e L L a a n n d d i i n n g g P P a a g g e e F F e e a a t t u u r r e e Landing Page is a special feature configured under User Management . It can specify the message, content to be seen or specify which website to be accessed into when users try to access into the Inte[...]

Vigor2925 Series User’s Guide 77 4. In the following page, check the box of Landing page and click OK to save the settings. 5. Open any browser (e.g., FireFox, Internet Explorer). The logging pa ge will appear and asks for username and password. Please type the correct username and password. 6. Click Login . If the logging is successful, you will[...]

Vigor2925 Series User’s Guide 78 E E x x a a m m p p l l e e 2 2 ： ： T T h h e e s s y y s s t t e e m m w w i i l l l l c c o o n n n n e e c c t t t t o o h h t t t t p p : : / / / / w w w w w w . . d d r r a a y y t t e e k k . . c c o o m m a a u u t t o o m m a a t t i i c c a a l l l l y y a a f f t t e e r r l l o o g g g g i i n n g g[...]

Vigor2925 Series User’s Guide 79 4. Open any browser (e.g., FireFox, Internet Explorer). The logging pa ge will appear and asks for username and password. Please type the correct username and password. 5. Click Login . If the logging is successful, you will be directed into the website of www.draytek.com .[...]

Vigor2925 Series User’s Guide 80 3 3 . . 8 8 H H o o w w t t o o S S e e n n d d a a N N o o t t i i f f i i c c a a t t i i o o n n t t o o S S p p e e c c i i f f i i e e d d P P h h o o n n e e N N u u m m b b e e r r v v i i a a S S M M S S S S e e r r v v i i c c e e i i n n W W A A N N D D i i s s c c o o n n n n e e c c t t i i o o n n Fol[...]

Vigor2925 Series User’s Guide 81 4. After finished the settings, click OK to return to previous page. Now you have finished the configuration of the SMS Provider profile setting. 5. Open Object Settings>>Notification Object to configure the event conditions of the notification. 6. Choose any index number (e.g., Index 1 in th is case) to con[...]

Vigor2925 Series User’s Guide 82 7. After finished the settings, click OK to return to previous page. You have finished the configuration of the notification object profile setting. 8. Now, open Application >> SMS / Mail Alert Service . Use the drop down list to choose SMS Provider and the Notify Profile (specify the time of sending SMS). T[...]

Vigor2925 Series User’s Guide 83 R R e e m m a a r r k k : : H H o o w w t t h h e e c c u u s s t t o o m m i i z z e e t t h h e e S S M M S S P P r r o o v v i i d d e e r r Choose one of the Index numbers (9 or 10) allowing you to custom ize the SMS Provider. In the web page, type the URL string of the SMS provider and type the username and p[...]

Vigor2925 Series User’s Guide 84 3 3 . . 9 9 H H o o w w t t o o C C r r e e a a t t e e a a n n A A c c c c o o u u n n t t f f o o r r M M y y V V i i g g o o r r The website of MyVigor (a server located on http://myvigor.draytek.com ) provides several useful services (such as Anti-Spam, Web Content Filter, Anti-Intrusion, and etc.) to filterin[...]

Vigor2925 Series User’s Guide 85 2. Click the Activate link. A login page for MyVigor web site will pop up automatically. 3. Click the link of Create an account now . 4. Check to confirm that you accept the Agreement and click Accept .[...]

Vigor2925 Series User’s Guide 86 5. Type your personal information in this page and then click Continue . 6. Choose proper selection for your computer and click Continue .[...]

Vigor2925 Series User’s Guide 87 7. Now you have created an account successfully. Click START. 8. Check to see the confirmation email with the title of New Account Confirmation Letter from myvigor.draytek.com . 9. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register p[...]

Vigor2925 Series User’s Guide 88 10. When you see the following page, please type in the account and password (that y ou just created) in the fields of UserName and Password . 11. Now, click Login . Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. 3 3 . . 9 9 . . 2 2 C C r r e [...]

Vigor2925 Series User’s Guide 89 2. Check to confirm that you accept the Agreement and click Accept . 3. Type your personal information in this page and then click Continue . 4. Choose proper selection for your computer and click Continue .[...]

Vigor2925 Series User’s Guide 90 5. Now you have created an account successfully. Click START. 6. Check to see the confirmation email with the title of New Account Confirmation Letter from myvigor.draytek.com . 7. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register p[...]

Vigor2925 Series User’s Guide 91 8. When you see the following page, please type in the account and password (that you just created) in the fields of UserName and Password . Then type the code in the box of Auth Code according to the value displayed on the right side of it. Now, click Login . Your account has been activated. You can access into M[...]

Vigor2925 Series User’s Guide 92 3 3 . . 1 1 0 0 H H o o w w t t o o C C o o n n f f i i g g u u r r e e C C e e r r t t a a i i n n C C o o m m p p u u t t e e r r s s A A c c c c e e s s s s i i n n g g t t o o I I n n t t e e r r n n e e t t We can specify certain computers (e.g., 192.168.1.10 ~ 192.168.1.20) accessing to Internet through Vigo[...]

Vigor2925 Series User’s Guide 93 3. Check the box of Check to enable the Filter Rule . Type the comments (e.g., block_all ). Choose Block If No Further Match for the Filter setting. Then, click OK . Note: In default, the router will check the packets starting with Set 2, Filter Rule 2 to Filter Rule 7. If Block If No Further Match for is selected[...]

Vigor2925 Series User’s Guide 94 6. A dialog box will be popped up. Choose Range Address as Address Type by using the drop down list. Type 192.168.1. 10 in the field of Start IP , and t ype 192.168.1.20 in the field of End IP . Then, click OK to save the settings. The com puters within the range can access into the Internet. 7. Now, check the con[...]

Vigor2925 Series User’s Guide 95 8. Both filter rules have been created. Click OK . 9. Now, all the settings are configured well. Only the computers with the IP addresses within 192.168.1.10 ~ 192.168.1.20 can access to Internet.[...]

Vigor2925 Series User’s Guide 96 3 3 . . 1 1 1 1 H H o o w w t t o o B B l l o o c c k k F F a a c c e e b b o o o o k k S S e e r r v v i i c c e e A A c c c c e e s s s s e e d d b b y y t t h h e e U U s s e e r r s s v v i i a a W W e e b b C C o o n n t t e e n n t t F F i i l l t t e e r r / / U U R R L L C C o o n n t t e e n n t t F F i i[...]

Vigor2925 Series User’s Guide 97 2. Open CSM >> Web Content Filter Profile to create a WCF profile. Check Social Networking with Action , Block . 3. Enable this profile in Firewall>>General Setup>>Default Rule .[...]

Vigor2925 Series User’s Guide 98 4. Next time when someone accesses facebook via this router, the web page would be blocked and the following message would be displayed instead. I I I I . . V V i i a a U U R R L L C C o o n n t t e e n n t t F F i i l l t t e e r r A. Block the web page containing the word of “Facebook” 1. Open Object Setting[...]

Vigor2925 Series User’s Guide 99 5. When you finished the above steps, click OK . Then, open Firewall>>General Setup . 6. Click the Default Rule tab. Choose the profile just configured from the drop dow n list in the field of URL Content Filter . Now, users cannot open any web page with the word “facebook” inside. B. Disallow users to p[...]

Vigor2925 Series User’s Guide 100 3. Open CSM>>URL Content Filter Profile . Click an index number to open the setting page. 4. Configure the settings as the following figure. 5. When you finished the above steps, please open Firewall>>General Setup .[...]

Vigor2925 Series User’s Guide 101 6. Click the Default Rule tab. Choose the profile just configured from the drop dow n list in the field of URL Content Filter. Now, users cannot open any web page with the word “facebook” inside.[...]

Vigor2925 Series User’s Guide 102 3 3 . . 1 1 2 2 H H o o w w t t o o S S e e t t u u p p A A d d d d r r e e s s s s M M a a p p p p i i n n g g Address Mapping is used to map a specified private IP or a range of private IPs of NAT subnet into a specified WAN IP (or WAN IP alias IP). Refer to the following figure. Suppose the WAN settings for a [...]

Vigor2925 Series User’s Guide 103 3. Click the Details Page of WAN 1 to open the following page. Fro m the above figure, set main WAN IP address as 202.211.100.10 . Click the WAN IP Alias button to configure the other P address which is 202.211.100.11. Make sure Join IP NAT Pool is not checked. Click OK to save the settings.[...]

Vigor2925 Series User’s Guide 104 4. After finished configuration for WAN1, open Load-Balance/Route Policy . 5. Click Index number 1 and 2 to configure th e details. After finished the settings, click OK to save the settings respectively.[...]

Vigor2925 Series User’s Guide 105 And 6. Upon completing the above configuration, you have specified the outgoing IP address(es) for some specific computers. 7. Now, you bind some specific computers to some WAN IP alias for outg oing traffic.[...]

Vigor2925 Series User’s Guide 106 3 3 . . 1 1 3 3 H H o o w w t t o o S S e e t t u u p p L L o o a a d d B B a a l l a a n n c c e e f f o o r r P P a a c c k k e e t t s s ? ? The following figure shows a simple application of load balance. WAN1 and WAN2 can be used to access into Internet. The PC in LAN1 can send the data to the remote PC thro[...]

Vigor2925 Series User’s Guide 107 3. In the following page, check Enable ; set Dest IP Start and Dest IP End with 203.65.1.35 and 203.65.1.35; choose WAN1 as the Interface ; click default gateway ; do not check Auto Failover To The Other WAN . 4. After finished the above settings, click OK to save the configuration. Now, the packets sent to the r[...]

Vigor2925 Series User’s Guide 108 3 3 . . 1 1 4 4 H H o o w w t t o o A A u u t t h h e e n n t t i i c c a a t t e e C C l l i i e e n n t t s s v v i i a a U U s s e e r r M M a a n n a a g g e e m m e e n n t t Before using the function of User Management, please make sure User-Based has been selected as the Mode in the User Management>>[...]

Vigor2925 Series User’s Guide 109 A A u u t t h h e e n n t t i i c c a a t t i i o o n n v v i i a a W W e e b b  If a LAN client who hasn’t passed the authentication opens an external web site in his browser, he will be redirected to the router’s Web authentication interface first. Then, the client is trying to access http://www.draytek.[...]

Vigor2925 Series User’s Guide 110  With Crome browser, you may get the following warning. Click Proceed anyway . After that, the web authentication window w ill appear. Input the user nam e and the password for your account (defined in User Management ) and click Login .[...]

Vigor2925 Series User’s Guide 111 If the authentication is successful, the client will be redirected to the original web site that he tried to access. In this example, it is http://www.draytek.com . Furthermore, you will get a popped up window as the following. Then you can access the Internet. Note, if you block the web browser to pop up any win[...]

Vigor2925 Series User’s Guide 112  In above description, you access an external web site to trigger the authentication. You may also directly access the router’s Web UI for authentication. Both HTTP and HTTPS are supported, for example http://192.168.1.1 or https://192.168. 1.1 . Replace 192.168.1.1 with your router’s real IP address, and [...]

Vigor2925 Series User’s Guide 113  Don’t setup a user profile in User Management and a VPN Remote Dial-in user profile with the same Username. Otherwise, you may get unexpected result. It is because the VPN Remote Dial-in User profiles can be extended to the User profiles in User Management for authentication. There are two different behavio[...]

Vigor2925 Series User’s Guide 114 A A u u t t h h e e n n t t i i c c a a t t i i o o n n v v i i a a T T e e l l n n e e t t The LAN clients can also authen ticate their accounts via telnet. 1. Telnet to the router’s LAN IP address and input the account name for the authentication: 2. Type the password for authentication and press Enter . The [...]

Vigor2925 Series User’s Guide 115 4. If the Time Quota is set with “0” minute, you will get the following message which means this account has no time quota. If the Time Quota is enabled and time is not 0 minute, You will get the following message. The expired tim e is shown after you login. After you run out the available time, you can’t u[...]

Vigor2925 Series User’s Guide 116 A A u u t t h h e e n n t t i i c c a a t t i i o o n n v v i i a a V V i i g g o o r r P P r r o o A A l l e e r r t t N N o o t t i i c c e e T T o o o o l l Authentication via Web or Telnet is convenient for users; however, it has some limitations. The most advantage with VigorPro Alert Notice Tool to operate [...]

Vigor2925 Series User’s Guide 117[...]

Vigor2925 Series User’s Guide 118 3 3 . . 1 1 5 5 H H o o w w t t o o u u s s e e D D N N S S F F i i l l t t e e r r The DNS Filter monitors DNS queries on UDP port 53 and will pass the DNS query information to the WCF (web content filter) to help with categorizing HTTPS URL's. Note: For DNS filter must use the WCF service profile to filter[...]

Vigor2925 Series User’s Guide 119 3. Click OK to save the configuration. 4. A message box will appear. It's a message which reminds that the priority of URL Content Filter is higher than Web Content Filter. Just press OK button to continue. 5. Open CSM>>DNS Filter . Enable the DNS filter; choose Block as the Sy slog; choose WCF-1 Defau[...]

Vigor2925 Series User’s Guide 120 From the Syslog, we can find out “google” is blocked.[...]

Vigor2925 Series User’s Guide 121 3 3 . . 1 1 6 6 H H o o w w t t o o u u s s e e A A P P M M a a n n a a g g e e m m e e n n t t f f u u n n c c t t i i o o n n ( ( i i n n V V i i g g o o r r 2 2 9 9 2 2 5 5 ) ) t t o o c c h h e e c c k k A A P P s s t t a a t t u u s s a a n n d d d d e e p p l l o o y y W W L L A A N N p p r r o o f f i i l [...]

Vigor2925 Series User’s Guide 122 Note: Apply to All APs can automatically apply the settings on Default profile t o all of the access points registered to Vigor2925 later. Hence, it is not necessary for you to manually apply wireless profiles for APs resp ectively. Such feature will be convenient for people who want to quickly deploy multiple Vi[...]

Vigor2925 Series User’s Guide 123 5. The following page is offered for you to modify related settings for 5G SSID of managed AP. Continue to make any changes you want. After finished all of the changes, simply click Finish . Now, the AP (represented with AP800_00507F6EE4980 ) detected by Vigor router will be applied with the settings modified by [...]

Vigor2925 Series User’s Guide 124 This page is left blank.[...]

Vigor2925 Series User’s Guide 125 A A d d v v a a n n c c e e d d C C o o n n f f i i g g u u r r a a t t i i o o n n This chapter will guide users to execute advanced (full) configuration thr ough admin mode operation. 1. Open a web browser on your PC and type http://192. 168.1.1. The window will ask for typing username and password. 2. Please t[...]

Vigor2925 Series User’s Guide 126 From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further[...]

Vigor2925 Series User’s Guide 127 automatically. The supported 3G USB Modem will be listed on DrayTek web site. Please visit www.draytek.com for more detailed information. Below shows the menu items for WAN . 4 4 . . 1 1 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p This section will introduce some general settings of Internet a nd expl[...]

Vigor2925 Series User’s Guide 128 Enable V means such WAN interface is enabled and ready to be used. Physical Mode / Type Display the physical mode and physical type of such WAN interface. Line Speed Display the downstream and upstream rate of such WAN interface. Active Mode Display whether such WAN interface is Active device or backup device. No[...]

Vigor2925 Series User’s Guide 129 Line Speed If your choose According to Line Speed as the Load Balance Mode , please type the line speed for downloading and uploading for such WAN interface. The unit is k bps. VLAN Tag insertion Enable – Enable the function of VLAN with tag. The router will add specific VLAN number to all packets on the WAN wh[...]

Vigor2925 Series User’s Guide 130 W W A A N N 3 3 w w i i t t h h U U S S B B To use 3G network connection through 3G USB Modem , please configure WAN3 interface. Available settings are explained as follows: Item Description Enable Choose Yes to invoke the settings for this WAN interface. Choose No to disable the settings for this WAN interface. [...]

Vigor2925 Series User’s Guide 131 Load Balance : Check this box to enable auto load balance function for such WAN interface. When the data traffic is large, the WAN interface with the function enabled will balance the data transmission automatically among all of the WAN interfaces in connection status. After finished the above settings, click OK [...]

Vigor2925 Series User’s Guide 132 Details Page This button will open different web page (based on IPv4) according to the access mode that you choose in WAN interface. Note that Details Pag e will be changed slightly based on ADSL/VDSL physical mode specified on WAN>>General Setup . IPv6 This button will open different web page (based on Phy[...]

Vigor2925 Series User’s Guide 133 Password – Type in the password provided by ISP in this field. The maximum length of the password you can set is 62 characters. Index (1-15) in Schedule Setup - You can type in four sets of time schedule for your request. All the schedules can be set previously in Application >> Schedule web page and you [...]

Vigor2925 Series User’s Guide 134 Fixed IP – Click Yes to use this function and type in a fixed IP address in the box of Fixed IP Address . Default MAC Address – You can use Default MAC Address or specify another MAC address by typing on the boxes of MAC Address for the router. Specify a MAC Address – Type the MAC address f or the router ma[...]

Vigor2925 Series User’s Guide 135 Available settings are explained as follows: Item Description Enable / Disable Click Enable for activating this function. If you click Disable , this function will be closed and all the settings that you adjusted in this page will be invalid. Keep WAN Connection Normally, this function is designed for Dynamic IP [...]

Vigor2925 Series User’s Guide 136 is 1492. RIP Protocol Routing Information Protocol is abbreviated as RIP （ RFC1058 ） specifying how routers exchange routing tables information. Click Enable RIP for activating this function. WAN IP Network Settings This group allows you to obtain an IP address automatically and allows you type in IP address [...]

Vigor2925 Series User’s Guide 137  Subnet Mask : Type the subnet mask.  Gateway IP Address : Type the gateway IP address. Default MAC Address : Click this radio button to use default MAC address for the router. Specify a MAC Address : Some Cable service providers specify a specific MAC address for acce ss authentication. In such cases you n[...]

Vigor2925 Series User’s Guide 138 address for DHCP server. ISP Access Setup Username -Type in the username provided by ISP in this field. The maximum length of the user nam e you can set is 63 characters. Password -Type in the password provided by ISP in this field. The maximum length of the password you can set is 62 characters. Index (1-15) in [...]

Vigor2925 Series User’s Guide 139 Specify an IP address – Click this radio button to specify some data.  IP Address – Type the IP address.  Subnet Mask – Type the subnet mask. After finishing all the settings here, please click OK to activate them. D D e e t t a a i i l l s s P P a a g g e e f f o o r r 3 3 G G / / 4 4 G G U U S S B B[...]

Vigor2925 Series User’s Guide 140 Modem Initial String Such value is used to initia lize USB modem. Please use the default value. If you have any question, please contact to your ISP. The maximum length of the string you can set is 47 characters. APN Name APN means Access Point Name which is provided and required by some ISPs. Type the name and c[...]

Vigor2925 Series User’s Guide 141 D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – – O O f f f f l l i i n n e e i i n n W W A A N N 1 1 / / W W A A N N 2 2 / / W W A A N N 3 3 When Offline is selected, the IPv6 connection will be disabled. D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – ?[...]

Vigor2925 Series User’s Guide 142 Note : At present, the IPv6 prefix can be acquired via the PPPoE mode connection which is available for the areas such as Taiwan (h inet), the Netherlands, Australia and UK. D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – – T T S S P P C C i i n n W W A A N N 1 1 / / W W A A N N 2 2 [...]

Vigor2925 Series User’s Guide 143 Item Description Username Type the name obtained from the broker. It is suggested for you to apply another usernam e and password for http://gogonet.gogo6.com/page/freenet6-account . The maximum length of the name you can set is 63 characters. Password Type the password assigned with the user name. The maximum le[...]

Vigor2925 Series User’s Guide 144 Confirm Password Type the password again to make the confirmation. Tunnel Broker Type the address for the tunnel broker IP, FQDN or an optional port number. Subnet Prefix Type the subnet prefix address getting from service provider. The maximum length of the prefix you can set is 128 characters. After finished th[...]

Vigor2925 Series User’s Guide 145 D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – – D D H H C C P P v v 6 6 C C l l i i e e n n t t i i n n W W A A N N 1 1 / / W W A A N N 2 2 DHCPv6 client mode would use DHCPv6 protocol to obtain IPv6 address from server. Available settings are explained as follows: Item Description[...]

Vigor2925 Series User’s Guide 146 D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – – S S t t a a t t i i c c I I P P v v 6 6 i i n n W W A A N N 1 1 / / W W A A N N 2 2 This type allows you to setup sta tic IPv6 address for WAN interface. Available settings are explained as follows: Item Description Static IPv6 Addres[...]

Vigor2925 Series User’s Guide 147 D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – – 6 6 i i n n 4 4 S S t t a a t t i i c c T T u u n n n n e e l l i i n n W W A A N N 1 1 / / W W A A N N 2 2 This type allows you to setup 6in4 Static Tunnel for WAN interface. Such mode allows the router to access IPv6 network through[...]

Vigor2925 Series User’s Guide 148 Below shows an example for successful IPv6 connection based on 6in4 Static Tunnel mode. D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P v v 6 6 – – 6 6 r r d d i i n n W W A A N N 1 1 / / W W A A N N 2 2 This type allows you to setup 6rd for WAN interface. Available settings are explained as f[...]

Vigor2925 Series User’s Guide 149 6rd Prefix Type the 6rd IPv6 address. 6rd Prefix Length Type the IPv6 prefix length for the 6rd IPv6 prefix i n number of bits. After finished the above settings, click OK to save the settings. Below shows an example for successful IPv6 connection based on 6rd mode.[...]

Vigor2925 Series User’s Guide 150 4 4 . . 1 1 . . 4 4 M M u u l l t t i i - - V V L L A A N N Multi-VLAN allows users to create profil es for specific WAN interface and bridge connections for user applications that requi re very high network through put. Simply go to WAN and select Multi-VLAN . G G e e n n e e r r a a l l This page shows the basi[...]

Vigor2925 Series User’s Guide 151 Available settings are explained as follows: Item Description Multi-VLAN Channel 8/9/10 Enable – Click it to enable the configuration of this channel. Disable – Click it to disable the configuration of this channel. WAN Type The connections and interfaces created in every channel may select a specific WAN typ[...]

Vigor2925 Series User’s Guide 152 please contact with your ISP and then click WAN link of Channel 5, 6 or 7 to configure your router. Available settings are explained as follows: Item Description Multi-VLAN Channel 5/6/7 Enable – Click it to enable the configuration of this channel. Disable – Click it to disable the configuration of this chan[...]

Vigor2925 Series User’s Guide 153 General Settings VLAN Tag – Type the value as the VLAN ID number. Valid settings are in the range from 1 to 4095. The network traffic flowing on each channel will be identified by the system via their VLAN Tags. Channels using the same WAN type may not configure the same VLAN tag value. Priority – Choose the [...]

Vigor2925 Series User’s Guide 154 4 4 . . 1 1 . . 5 5 W W A A N N B B u u d d g g e e t t This function is used to determine the data traffic volume for each WAN interface respectively to prevent from overcharges for data transmission by the ISP. Please note that the Time and Date settings will need to be configured correctly first in order for s[...]

Vigor2925 Series User’s Guide 155 Budget Action The system can choose one of the following actions to perform when the traffic has exceeded the budget limit. Shutdown WAN interface – All the outgoing traffic through such WAN interface will be terminated. Send Mail Alert to Administrator – The system will send out a warning message to the admi[...]

Vigor2925 Series User’s Guide 156 will serve for IP routing to help hosts in the public subnet to communicate with other public hosts or servers outside. Therefore, the router shoul d be set as the gateway for public hosts. W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o [...]

Vigor2925 Series User’s Guide 157 4 4 . . 2 2 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p This page provides you the general settings for LAN. Click LAN to open the LAN settings page and choose General Setup . There are four subnets provided by the router which allow users to divide groups into d ifferent subnets (LAN1 – LAN5). In a[...]

Vigor2925 Series User’s Guide 158 Advanced DHCP packets can be processed by adding option number and data information when such function is enabled. E nable/Disable – Enable/Disable the function of DHCP Option. Each DHCP option is composed by an option number with data. For example, Option number:100 Data: abcd When such function is enabled, th[...]

Vigor2925 Series User’s Guide 159 D D e e t t a a i i l l s s P P a a g g e e f f o o r r L L A A N N 1 1 – – E E t t h h e e r r n n e e t t T T C C P P / / I I P P a a n n d d D D H H C C P P S S e e t t u u p p There are two configuration pages for LAN1 , Ethernet TCP/IP and DHCP Setup (based on IPv4) and IPv6 Setup. Click the tab for e ac[...]

Vigor2925 Series User’s Guide 160 request to. DHCP Server IP Address – It is available when Enable Relay Agent is checked. Set the IP address of the DHCP server you are going to use so the Relay Agent can help to forward the DHCP request to the DHCP server . S tart IP Addr ess - Enter a value of the IP address pool for the DHCP server to start [...]

Vigor2925 Series User’s Guide 161 D D e e t t a a i i l l s s P P a a g g e e f f o o r r L L A A N N 1 1 – – I I P P v v 6 6 S S e e t t u u p p There are two configuration pages for LAN1 , Ethernet TCP/IP and DHCP Setup (based on IPv4) and IPv6 Setup. Click the tab for e ach type and refer to the following explanations for detailed informat[...]

Vigor2925 Series User’s Guide 162 list. DHCPv6 Server Configuration Enable Server –Click it to enable DHCPv6 server. DHCPv6 Server could assign IPv6 address to PC according to the Start/End IPv6 address configuration. Disable Server –Click it to disable DHCPv6 server. Start IPv6 Address / End IPv6 Address –Type the start and end address for[...]

Vigor2925 Series User’s Guide 163 D D e e t t a a i i l l s s P P a a g g e e f f o o r r L L A A N N 2 2 ~ ~ L L A A N N 5 5 a a n n d d D D M M Z Z Available settings are explained as follows: Item Description Network Configuration Enable/Disable - Click Enable to enable such configuration; click Disable to disable such configuration. For NAT U[...]

Vigor2925 Series User’s Guide 164 the DHCP server to start with when issuing IP addresses. If the 1st IP address of your router is 192.168.1.1, the starting IP address must be 192.168.1.2 or greater , but smaller than 192.168.1.25 4. IP Pool Counts - En ter the maxi mu m nu mber of P Cs tha t you want the DHCP server to assign IP addresses to. Th[...]

Vigor2925 Series User’s Guide 165 D D e e t t a a i i l l s s P P a a g g e e f f o o r r I I P P R R o o u u t t e e d d S S u u b b n n e e t t Available settings are explained as follows: Item Description Network Configuration Enable/Disable - Click Enable to enable such configuration; click Disable to disable such configuration. For Routing U[...]

Vigor2925 Series User’s Guide 166 192.168.1.25 4. IP Pool Counts - En ter the maxi mu m nu mber of P Cs tha t you want the DHCP server to assign IP addresses to. The default is 50 and the maxim um is 253. Lease Time - Enter the time to determ ine how long the IP address assigned by DHCP server can be used. Use LAN Port – Specify an IP for IP Ro[...]

Vigor2925 Series User’s Guide 167 4 4 . . 2 2 . . 3 3 S S t t a a t t i i c c R R o o u u t t e e Go to LAN to open setting page and choose Static Route . The router offers IPv4 and IPv6 for you to configure the static route. Both protocols bring different web pages. S S t t a a t t i i c c R R o o u u t t e e f f o o r r I I P P v v 4 4 Availabl[...]

Vigor2925 Series User’s Guide 168 Click any underline of index number to get the follow ing page. Available settings are explained as follows: Item Description Enable Check it to enable this profile. Destination IP Address T ype an IP address as the destination of such static route. Subnet Mask T ype the subnet mask for such static route. Network[...]

Vigor2925 Series User’s Guide 169 S S t t a a t t i i c c R R o o u u t t e e f f o o r r I I P P v v 6 6 You can set up to 40 profiles for IPv6 static route. Click the IPv6 tab to o pen the following page: Each item is explained as follows: Item Description Set to Factory Default Clear all of the settings and return to factory default settings. [...]

Vigor2925 Series User’s Guide 170 Destination IPv6 Address / Prefix Len T ype the IP address with the prefix length for this entry . Gateway IPv6 Address T ype the gateway address for this entry . Network Interface Use the drop down list to specify an interface for this static route. After finishing all the settings here, please click OK to save [...]

Vigor2925 Series User’s Guide 171 1. Go to LAN page and click General Setup , select 1st Subnet as the RIP Protocol Control. Then click the OK button. Note: There are two reasons that we have to appl y RIP Protocol Control on 1st Subnet. The f irst is that the LAN interface can exchange RIP packets with the neighboring routers via the 1st subnet [...]

Vigor2925 Series User’s Guide 172 4. Go to Diagnostics and choose Routing T able to verify current routing table. 4 4 . . 2 2 . . 4 4 V V L L A A N N With the 5-port Gigabit switch on the LAN side, Vigor router provides extremely high speed connectivity for the highest speed local data transfer of any server or local PCs. On the wireless-equipped[...]

Vigor2925 Series User’s Guide 173 Note: Settings in this page only applied to LAN port but not W AN port. Available settings are explained as follows: Item Description Enable Click it to enable VLAN configuration. LAN P1 – P5 – Check the LAN port(s) to be grouped under the selected VLAN. Wireless LAN SSID1 – SSID4 – Check the SSID boxes t[...]

Vigor2925 Series User’s Guide 174 Please type the tag value and specify the priority for the packets sending by LAN. VID – Type the value as the VLAN ID number. The range is form 0 to 4095. Priority – Type the packet priority number for such VLAN. The range is from 0 to 7. Permit untagged device in P1 to access router It can help users to com[...]

Vigor2925 Series User’s Guide 175 2. After checking the box to enable VLAN function, you will check the table according to the needs as shown below. Click OK to save the settings. The Vigor router also supports up to six pr ivate IP subnets on the LAN. Each can be independent (isolated) or common (able to communicate with each other). This is ide[...]

Vigor2925 Series User’s Guide 176 4 4 . . 2 2 . . 5 5 B B i i n n d d I I P P t t o o M M A A C C This function is used to bind the IP and MAC address in LAN to have a strengthening co ntrol in network. When this function is enabled, all the assigned IP and MAC address binding together cannot be changed. If you modified the binding IP or MAC addr[...]

Vigor2925 Series User’s Guide 177 Refresh Refresh the ARP table listed below to obtain the newest ARP table information. Add or Update IP Address – Type the IP address that will be used for the specified MAC address. Mac Address – Type the MAC address that is used to bind with the assigned IP address. Comment – Type a brief description for [...]

Vigor2925 Series User’s Guide 178 4 4 . . 2 2 . . 6 6 L L A A N N P P o o r r t t M M i i r r r r o o r r LAN port mirror can be applied for the users in LAN. Generally speaking, this function copies traffic from one or more specific ports to a target port. This mechanism helps manager track the network errors or abnormal packets transm ission wi[...]

Vigor2925 Series User’s Guide 179 4 4 . . 2 2 . . 7 7 W W e e b b P P o o r r t t a a l l S S e e t t u u p p This page allows you to configure a profile with specified URL for accessing into or display a message when a wireless/LAN user co nnects to In ternet through this router. No matter what the purpose of the wireless/LAN client is, he/she w[...]

Vigor2925 Series User’s Guide 180 Available settings are explained as follows: Item Description Disable Click this button to close this function. URL Redirect Any user who wants to access into Internet through this router will be redirected to the URL specified here first. It is a useful method for the purpose of advertisement. For example, force[...]

Vigor2925 Series User’s Guide 181 Enable Check this box to enable this policy. Protocol Display the protocol used for this policy. Interface Display the interface to send p ackets to once the policy is matched. Interface Address Display the WAN IP or WAN IP alias address which is used as source IP of the outgoing packets. Src IP Start Displays th[...]

Vigor2925 Series User’s Guide 182 Protocol Use the drop-down menu to choose a proper protocol for the WAN interface. Source IP Any – Any IP can be treated as the source IP. Src IP Start - Type the source IP start for the specified WAN interface. Src IP End - Type the source IP end for the specified WAN interface. If this field is blank, it mean[...]

Vigor2925 Series User’s Guide 183 When you finish the configuration, please click OK to save and exit this page. 4 4 . . 4 4 N N A A T T Usually, the router serves as an NAT (Network Address Translation) router. NAT is a mechanism that one or more private IP addresses can be mapped into a single public one. Public IP address is usually assigned b[...]

Vigor2925 Series User’s Guide 184 Below shows the menu items for NAT. 4 4 . . 4 4 . . 1 1 P P o o r r t t R R e e d d i i r r e e c c t t i i o o n n Port Redirection is usually set up for server related service inside the local network (LAN), such as web servers, FTP servers, E-mail servers etc. Most of the case, you need a public IP address for[...]

Vigor2925 Series User’s Guide 185 Each item is explained as follows: Item Description Index Display the number of the profile. Service Name Display the description of the specific network service. WAN Interface Display the WAN IP address used by the profile. Protocol Display the transport layer protocol (TCP or UDP). Public Port Display the port [...]

Vigor2925 Series User’s Guide 186 Item Description Enable Check this box to enable such port redirection setting. Mode Two options (Single and Range) are provided here for you to choose. To set a range for the specific service, select Range . In Range mode, if the public port (start port and end port) and the starting IP of private IP had been en[...]

Vigor2925 Series User’s Guide 187 4 4 . . 4 4 . . 2 2 D D M M Z Z H H o o s s t t As mentioned above, Port Redirection can redirect incoming TCP/UDP or othe r traffic on particular ports to the specific private IP address/port of host in the LAN. However, other IP protocols, for example Protocols 50 (ESP) and 51 (A H), do not travel on a fixed po[...]

Vigor2925 Series User’s Guide 188 The security properties of NA T are somewhat bypassed if you set up DMZ host. W e suggest you to add additional filter rules or a secondary firewall. Click DMZ Host to open the following page. You can set different DMZ host for each WAN interface. Click the WAN tab to switch into the configuration page for that W[...]

Vigor2925 Series User’s Guide 189 Choose PC Click this button and then a window will autom atically pop up, as depicted below. The window consists of a list of private IP addresses of all hosts in your LAN network. Select one private IP address in the list to be the DMZ host. When you have selected one private IP from the above dialog, the IP add[...]

Vigor2925 Series User’s Guide 190 If you previously have set up WAN Alias for PPPoE or Static or Dynamic IP mode in WAN2 interface , you will find them in Aux. WAN IP for your selection. Available settings are explained as follows: Item Description Enable Check to enable the DMZ Host function. Private IP Enter the private IP address of the DMZ ho[...]

Vigor2925 Series User’s Guide 191 4 4 . . 4 4 . . 3 3 O O p p e e n n P P o o r r t t s s Open Ports allows you to open a range of ports for the traffic of special applications. Common application of Open Ports includes P2P application (e.g., BT, KaZaA, Gnutella, WinMX, eMule and others), Internet Camera etc. Ensure that you keep the application [...]

Vigor2925 Series User’s Guide 192 Available settings are explained as follows: Item Description Enable Open Ports Check to enable this entry. Comment Make a name for the defined network application/service. WAN Interface Specify the WAN interface that w ill be used for this entry. WAN IP Specify the WAN IP address that will be used for this entry[...]

Vigor2925 Series User’s Guide 193 After finishing all the settings here, please click OK to save the configuration. 4 4 . . 4 4 . . 4 4 P P o o r r t t T T r r i i g g g g e e r r i i n n g g Port Triggering is a varia tion of open ports function. The key difference between "open port" and "port triggering" is:  Once the OK[...]

Vigor2925 Series User’s Guide 194 Comment Display the text which memorizes the application of this rule. Triggering Protocol Display the protocol of the triggering packets. Triggering Port Display the port of the triggering packets. Incoming Protocol Display the protocol for the incoming data of such triggering profile. Incoming Port Display the [...]

Vigor2925 Series User’s Guide 195 Triggering Port Type the port or port range for such triggering profile. Incoming Protocol When the triggering packets received, it is expected the incoming packets will use the selected protocol. Select the protocol (TCP, UDP or TCP/UDP) for the incoming data of such triggering profile. Incoming Port Type the po[...]

Vigor2925 Series User’s Guide 196 4 4 . . 5 5 H H a a r r d d w w a a r r e e A A c c c c e e l l e e r r a a t t i i o o n n Hardware Acceleration is also called PPA in DrayTek for it is based on Protocol Processing Engine (PPE) of Infinion. It can only support 128 sessions for netw ork traffic (IN & OUT) with implementing three kinds of m o[...]

Vigor2925 Series User’s Guide 197 available in Auto Mode, too. But the UDP protocol is onl y supported in this sub-item. Apply the Class Rule in Quality of Service – Users can apply the information provi ded by QoS in this sub-item. Note: Please visit our website for referring the detailed configuration of QoS. Specific Hosts – This sub-item [...]

Vigor2925 Series User’s Guide 198 4 4 . . 6 6 F F i i r r e e w w a a l l l l 4 4 . . 6 6 . . 1 1 B B a a s s i i c c s s f f o o r r F F i i r r e e w w a a l l l l While the broadband users demand more bandwidth f or multimedia, interactive applications, or distance learning, security has been always the most concerned. The firewall of the Vigo[...]

Vigor2925 Series User’s Guide 199 S S t t a a t t e e f f u u l l P P a a c c k k e e t t I I n n s s p p e e c c t t i i o o n n ( ( S S P P I I ) ) Stateful inspection is a firewall architecture that works at the network layer. Unlike legacy static packet filtering, which examines a packet based on the information in its header, stateful inspec[...]

Vigor2925 Series User’s Guide 200 4 4 . . 6 6 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p General Setup allows you to adjust setti ngs of IP Filter and common options. Here you can enable or disable the Call Filter or Data Filter . Under some circumstance, your filter set can be linked to work in a serial manner. So here you assign th[...]

Vigor2925 Series User’s Guide 201 Enable S trict Security Firewall For the sake of security , the router will execute strict security checking for data transmission. Such feature is enabled in default. All the packets, while transmitting through Vigor router, will be filtered by firewall. If the firewall system (e.g., content filter server) does [...]

Vigor2925 Series User’s Guide 202 Available settings are explained as follows: Item Description Filter Select Pass or Block for the packets that do not match with the filter rules. Sessions Control The number typed here is the total sessions of the packets that do not match the filter rule configured in this page. The default setting is 60000. Qu[...]

Vigor2925 Series User’s Guide 203 Syslog server . Please refer to section Syslog/Mail Alert for more detailed information. URL Content Filter Select one of the URL Content Filter profile settings (created in CSM>> URL Content Filter ) for applying with this router . Pl ease set at least one profile for choosing in CSM>> URL Content Fi[...]

Vigor2925 Series User’s Guide 204 Window size – It determines the size of TCP protocol (0~65535). T he more the value is, the better the performance will be. However , if the network is not stable, small value will be proper . Session timeout – Setting timeout for sessions can make the best utilization of network resources. After finishing al[...]

Vigor2925 Series User’s Guide 205 4 4 . . 6 6 . . 3 3 F F i i l l t t e e r r S S e e t t u u p p Click Firewall and click Filter Setup to open the setup page. To edit or add a filter, click on the set numbe r to edit the individual set. The following page will be shown. Each filter set contains up to 7 rules. Click on the rule num ber button to [...]

Vigor2925 Series User’s Guide 206 Available settings are explained as follows: Item Description Check to enable the Filter Rule Check this box to enable the filter rule. Comments Enter filter set comments/description. Maximum length is 14- character long. Index(1-15) Set PCs on LAN to work at certain time interval only. You may choose up to 4 sch[...]

Vigor2925 Series User’s Guide 207 Note: RT means routing domain for 2nd subnet or other LAN. Source/Destination IP Click Edit to access into the follo wing dialog to choose the source/destination IP or IP ranges. To set the IP address manually, please choose Any Address/Single Address/ Range Address/Subnet Address as the Address Type and type the[...]

Vigor2925 Series User’s Guide 208 To set the service type manually, please choose User defined as the Service Type and type them in this dialog. In addition, if you want to use the service type from defined groups or objects, please choose Group and Objects as the Service Type. Protocol - Specify the protocol(s) which this filter rule will apply [...]

Vigor2925 Series User’s Guide 209 passed immediately. Block If No Further Match - A packet matching the rule, and that does not match furthe r rules, will be dropped. Pass If No Further Match - A packet matching the rule, and that does not match further rules, will be passed through. Branch to other Filter Set If the packet matches the filter rul[...]

Vigor2925 Series User’s Guide 210 troubleshooting needs, you can specify to record inform ation for IM/P2P by checking the Log box. It will be sent to Syslog server . Please refer to section Syslog/Mail Alert for more detailed information. URL Content Filter Select one of the URL Content Filter profile settings (created in CSM>> URL Content[...]

Vigor2925 Series User’s Guide 211 I. If you do not choose any codepage, no decoding job of URL will be processed. Please use the drop-down list to choose a codepage. If you do not have any idea of choosing suitable codepage, please open Syslog. From Codepage Information of Setup dialog, you will see the recommended codepage listed on the dialog b[...]

Vigor2925 Series User’s Guide 212 E E x x a a m m p p l l e e As stated before, all the traffic will be separated and arbitrated using on of two IP filters: call filter or data filter. You may preset 12 call filters and data filters in Filter Setup and even link them in a serial manner. Each filter set is composed by 7 filter rules, which can be [...]

Vigor2925 Series User’s Guide 213 4 4 . . 6 6 . . 4 4 D D o o S S D D e e f f e e n n s s e e As a sub-functionality of IP Filter/Firewall, there are 15 types of detect/ defense function in the DoS Defense setup. The DoS Defense functionality is disabled for default. Click Firewall and click DoS Defense to open the setup page. Available settings [...]

Vigor2925 Series User’s Guide 214 will start to randomly discard the subsequent UDP packets for a period defined in Timeout. The default setting for threshold and timeout are 150 packets per second and 10 seconds, respectively. That means, when 150 packets per second received, they will be regarded as “attack event” and the session will be pa[...]

Vigor2925 Series User’s Guide 215 Any broadcast UDP packets received from the Internet is blocked. Activating the DoS/DDoS defense functionality might block some legal packets. For example, when you act ivate the fraggle attack defense, all broadcast UDP packets coming from the Internet are blocked. Therefore, the RIP packets from the Internet mi[...]

Vigor2925 Series User’s Guide 216 After finishing all the settings here, please click OK to save the configuration.[...]

Vigor2925 Series User’s Guide 217 4 4 . . 7 7 U U s s e e r r M M a a n n a a g g e e m m e e n n t t User Management is a security feature which disallows any IP traffic (except DHCP-related packets) from a particular host until that host has correctly supplied a valid username and password. Instead of managing with IP address/MAC address, User [...]

Vigor2925 Series User’s Guide 218 4 4 . . 7 7 . . 1 1 G G e e n n e e r r a a l l S S e e t t u u p p General Setup can determine the standard (rule-based or user-based) for the users controlled by User Management. The mode (standard) selected here will influence the contents of the filter rule(s) applied to every user. Available settings are exp[...]

Vigor2925 Series User’s Guide 219 4 4 . . 7 7 . . 2 2 U U s s e e r r P P r r o o f f i i l l e e This page allows you to set customized profiles (up to 200) which will be applied for users controlled under User Management . Simply open User Management>>User Profile . To set the user profile, please click any index number link to open the f[...]

Vigor2925 Series User’s Guide 220 Available settings are explained as follows: Item Description Enable this account Check this box to enable such user profile. User Name Type a name for such user profile (e.g., LAN_User_Group_1, WLAN_User_Group_A, WLAN_User_Group_B, etc). When a user tries to access Internet through this router, an authentication[...]

Vigor2925 Series User’s Guide 221 For the detailed configuration, simply refer to Firewall>>Filter Rule . The firewall filter rules that are not selected in Firewall>>General>>Defa ult rule can be available for use in User Management>>User Profile . Log Time of login/log out, bl ock/unblock for the user(s) can be sent to a[...]

Vigor2925 Series User’s Guide 222 Landing Page field in User Management>>General Setup . Check this box to enable such function. Index (1-15) in Schedule Setup You can type in four sets of time schedule for your request. All the schedules can be set previously in Application >> Schedule web page and you can use the number that you hav[...]

Vigor2925 Series User’s Guide 223 After finishing all the settings here, please click OK to save the configuration. 4 4 . . 7 7 . . 3 3 U U s s e e r r G G r r o o u u p p This page allows you to bind several user profiles into one group. These groups will be used in Firewall>>General Setup as part of filter rules. Please click any index nu[...]

Vigor2925 Series User’s Guide 224 on. Selected Keyword Objects Click button to add the selected user objects in this box. After finishing all the settings here, please click OK to save the configuration. 4 4 . . 7 7 . . 4 4 U U s s e e r r O O n n l l i i n n e e S S t t a a t t u u s s This page displays the user(s) connected to the router and r[...]

Vigor2925 Series User’s Guide 225 Data Quota Display the quota for data transmission. Idle Time Display the idle timeout setting for such profile. Action Block - can prevent specified user accessing into Internet. Unblock – the user will be blocked. Logout – the user will be logged out forcefully. 4 4 . . 8 8 O O b b j j e e c c t t s s S S e[...]

Vigor2925 Series User’s Guide 226 Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the object profile. To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index co lumn [...]

Vigor2925 Series User’s Guide 227 for IP address. Select Any Address if this object contains any IP address. Select Mac Address if this object contains Mac address. MAC Address Type the MAC address of the network card which will be controlled. Start IP Address Type the start IP address for Single Address type. End IP Address Type the end IP addre[...]

Vigor2925 Series User’s Guide 228 4 4 . . 8 8 . . 2 2 I I P P G G r r o o u u p p This page allows you to bind several IP objects into one IP group. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the group pr[...]

Vigor2925 Series User’s Guide 229 Available settings are explained as follows: Item Description Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose WAN, LAN or Any to display all the available IP objects with the specified interface. Available IP Objects All the available IP objects with the specified interface [...]

Vigor2925 Series User’s Guide 230 To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index co lumn for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Name Type a name for this profile. Maximum 15 characters are al[...]

Vigor2925 Series User’s Guide 231 3. After finishing all the settings, please click OK to save the configuration. 4 4 . . 8 8 . . 4 4 I I P P v v 6 6 G G r r o o u u p p This page allows you to bind several IPv6 objects into one IPv6 group. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. In[...]

Vigor2925 Series User’s Guide 232 Available settings are explained as follows: Item Description Name Type a name for this profile. Maximum 15 characters are allowed. Available IPv6 Objects All the available IPv6 objects with the specified interface chosen above will be shown in this box. Selected IPv6 Objects Click >> button to add the sele[...]

Vigor2925 Series User’s Guide 233 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Name Type a name for this profile. Protocol Specify the protocol(s) which this profile will apply to. Source/Destination Port Source Port and the Destination Port column are available for TCP/UDP prot[...]

Vigor2925 Series User’s Guide 234 4 4 . . 8 8 . . 6 6 S S e e r r v v i i c c e e T T y y p p e e G G r r o o u u p p This page allows you to bind several service types into one group. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. N[...]

Vigor2925 Series User’s Guide 235 Item Description Name Type a name for this profile. Available Service Type Objects All the available service objects that you have added on Objects Setting>>Service Type Object will be shown in this box. Selected Service Type Objects Click >> button to add the selected IP objects in this box. 3. After[...]

Vigor2925 Series User’s Guide 236 To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index co lumn for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Name Type a name for this profile, e.g., game. Type a name for [...]

Vigor2925 Series User’s Guide 237 4 4 . . 8 8 . . 8 8 K K e e y y w w o o r r d d G G r r o o u u p p This page allows you to bind several keyword objects into one group. The keyword groups set here will be chosen as black /white list in CSM >>URL /Web Content Filter Profile . Available settings are explained as follows: Item Description Se[...]

Vigor2925 Series User’s Guide 238 Available settings are explained as follows: Item Description Name Type a name for this group. Maximum 15 characters are allowed. Available Keyword Objects You can gather keyword objects from Keyword Object page within one keyword group. All the available Keyword objects that you have created will be shown in thi[...]

Vigor2925 Series User’s Guide 239 To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Profile column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Name Type a name for this profile. The maximum length [...]

Vigor2925 Series User’s Guide 240 4 4 . . 8 8 . . 1 1 0 0 S S M M S S / / M M a a i i l l S S e e r r v v i i c c e e O O b b j j e e c c t t S S M M S S S S e e r r v v i i c c e e O O b b j j e e c c t t This page allows you to set ten profiles which will be applied in Application>>SMS/Mail Alert Service . Each item is explained as follow[...]

Vigor2925 Series User’s Guide 241 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Name Type a name for such SMS profile. The maximum length of the name you can set is 31 characters. Service Provider Use the drop down list to specify the service provider which offers SMS ser[...]

Vigor2925 Series User’s Guide 242 C C u u s s t t o o m m i i z z e e d d S S M M S S S S e e r r v v i i c c e e Vigor router offers several SMS service provider to offer the SMS service. However, if your service provider cannot be found from the service provider list, si mply use Index 9 and Index 10 to make customized SMS service. The profile [...]

Vigor2925 Series User’s Guide 243 Username Type a user name that the sender can use to register to selected SMS provider. The maximum length of the name you can set is 31 characters. Password Type a password that the sender can use to register to selected SMS provider. The maximum length of the password you can set is 31 characters. Quota Type th[...]

Vigor2925 Series User’s Guide 244 To set a new profile, please do the steps listed below: 1. Click the Mail Server tab, and click the number (e.g., #1) under Index colum n for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Name Type a name for suc[...]

Vigor2925 Series User’s Guide 245 Authentication The mail server must be authenticated with the correct username and password to have the right of sending message out. Check the box to enable the function. Username – Type a name for authentication. The maximum length of the name you can se t is 31 characters. Password – Type a password for au[...]

Vigor2925 Series User’s Guide 246 To set a new profile, please do the steps listed below: 1. Open Object Setting>>Notification Object , and click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Nam[...]

Vigor2925 Series User’s Guide 247 4 4 . . 9 9 C C S S M M P P r r o o f f i i l l e e C C o o n n t t e e n n t t S S e e c c u u r r i i t t y y M M a a n n a a g g e e m m e e n n t t ( ( C C S S M M ) ) CSM is an abbreviation of Content Security Management which is used to control IM/P2P usage, filter the web content and URL content to reach a[...]

Vigor2925 Series User’s Guide 248 4 4 . . 9 9 . . 1 1 A A P P P P E E n n f f o o r r c c e e m m e e n n t t P P r r o o f f i i l l e e You can define policy profiles for IM (Instant Messenger)/P2P (Peer to Peer)/Protocol/Misc application. This page allows you to set 32 profiles for different requirements. The APP Enforcement Profile will be ap[...]

Vigor2925 Series User’s Guide 249 Below shows the items which are categorized under Protocol . Available settings are explained as follows: Item Description Profile Name Type a name for the CSM profile. The maximum length of the name you can set is 15 characters. Select All Click it to choose all of the items in this page. Clear All Uncheck all t[...]

Vigor2925 Series User’s Guide 250[...]

Vigor2925 Series User’s Guide 251 The items categorized under P2P ----- The items categorized under Misc -----[...]

Vigor2925 Series User’s Guide 252 4 4 . . 9 9 . . 2 2 U U R R L L C C o o n n t t e e n n t t F F i i l l t t e e r r P P r r o o f f i i l l e e To provide an appropriate cyberspace to users, Vigor router equips with URL Content Filter not only to limit illegal traffic from/to the inappropriate web sites but also prohibit other web feature where[...]

Vigor2925 Series User’s Guide 253 Administration Message You can type the message manually for your necessity. Default Message - You can type the message manually for your necessity or click this button to get the default message which will be displayed on the field of Administration Message . You can set eight profiles as URL content filter. Sim[...]

Vigor2925 Series User’s Guide 254 matching with the conditions specified in URL Access Control and Web Feature below, such function can determine the priority for the actions executed. For this one, the router will process the packages with the conditions set below for web feature first, then URL second. Log None – There is no log file will be [...]

Vigor2925 Series User’s Guide 255 supports multiple keywords. The keyword could be a noun, a partial noun, or a complete URL string. Multiple keywords within a frame are separated by space, co mma, or semicolon. In addition, the maximal length of each frame is 32-character long. After specifying keywords, the Vigor router will decline the connect[...]

Vigor2925 Series User’s Guide 256 Objects previously for passing or blocking the file downloading. After finishing all the settings, please click OK to save the configuration. 4 4 . . 9 9 . . 3 3 W W e e b b C C o o n n t t e e n n t t F F i i l l t t e e r r P P r r o o f f i i l l e e There are three ways to activate WCF on vigor router, using [...]

Vigor2925 Series User’s Guide 257 Available settings are explained as follows: Item Description Activate Click it to access into MyVigor for activating WCF service. Setup Query Server It is recommended for you to use the default setting, auto-selected. You need to sp ecify a server for categorize searching when you type URL in browser based on th[...]

Vigor2925 Series User’s Guide 258 Cache None – the router will check the URL that the user wants to access via WCF precisely, however, the processing rate is normal. Such item can provide the m ost accurate URL matching. L1 – the router will check the URL that the user wants to access via WCF. If the URL has been accessed previously, it will [...]

Vigor2925 Series User’s Guide 259 Available settings are explained as follows: Item Description Profile Name Type a name for the CSM profile. The maximum length of the name you can set is 15 characters. Black/White List Enable – Activate white/black list function for such profile. Group/Object Selections – Click Edit to choose the group or ob[...]

Vigor2925 Series User’s Guide 260 4 4 . . 9 9 . . 4 4 D D N N S S F F i i l l t t e e r r The DNS Filter monitors DNS queries on UDP port 53 and will pass the DNS query information to the WCF to help with categorizing HTTPS URL's. Note: For DNS filter must use the WCF service profile to filter the packets, therefore WCF license must be activ[...]

Vigor2925 Series User’s Guide 261 4 4 . . 9 9 . . 5 5 A A P P P P E E S S u u p p p p o o r r t t L L i i s s t t This page offers the software versions for each applications managed by APP Enforcement Profiles by Vigor router. Click the IM/P2P/PROTOCOL/MISC tab to open the information page for different APP type.[...]

Vigor2925 Series User’s Guide 262 4 4 . . 1 1 0 0 B B a a n n d d w w i i d d t t h h M M a a n n a a g g e e m m e e n n t t Below shows the menu items for Bandwidth Management. 4 4 . . 1 1 0 0 . . 1 1 S S e e s s s s i i o o n n s s L L i i m m i i t t A PC with private IP address can access to the Internet via NAT router. The router will gener[...]

Vigor2925 Series User’s Guide 263 Default session limit - Defines the default session number used for each computer in LAN. Limitation List Displays a list of specific limitations that you set on this web page. Specific Limitation Start IP- Defines the start IP address for limit session. End IP - Defines the end IP address for limit session. Maxi[...]

Vigor2925 Series User’s Guide 264 4 4 . . 1 1 0 0 . . 2 2 B B a a n n d d w w i i d d t t h h L L i i m m i i t t The downstream or upstream from FTP, HTTP or some P2P applications will occupy large of bandwidth and affect the applications for other programs. Please use Limit Bandwidth to m ake the bandwidth usage more efficient. In the Bandwidth[...]

Vigor2925 Series User’s Guide 265 downstream for each computer in LAN. Allow auto adjustment … .- Check this box to make the best utilization of available bandwidth. Limitation List Display a list of specific limitations that you set on this web page. Specific Limitation Start IP - Define the start IP address for limit bandwidth. End IP - Defin[...]

Vigor2925 Series User’s Guide 266 overcrowded network. This is especially essential to those are low tolerant of loss, delay or jitter (delay variation). Another reason is due to congestions at network intersections where speeds of interconnected circuits mismatch or traffic aggregates, packets will queue up and traffic can be throttled back to a[...]

Vigor2925 Series User’s Guide 267 Available settings are explained as follows: Item Description General Setup Index – Display the WAN interface number that you can edit. Status – Display if the WAN interface is available for such function or not. Bandwidth – Display the inbound and outbound bandwidth setting for the WAN interface. Direction[...]

Vigor2925 Series User’s Guide 268 This page displays the QoS settings result of the WAN interface. Click the Setup link to access into next page for the general setup of W AN interface. As to class rule, simply click the Edit link to access into next for configuration. You can configure general setup for the WAN interface, edit the Class Rule, an[...]

Vigor2925 Series User’s Guide 269 Available settings are explained as follows: Item Description Enable the QoS Control The factory default for this setting is checked. Please also define which traffic the QoS Control settings will apply to. IN - apply to incoming traffic only. OUT - apply to outgoing traffic only. BOTH - apply to both incoming an[...]

Vigor2925 Series User’s Guide 270 E E d d i i t t t t h h e e C C l l a a s s s s R R u u l l e e f f o o r r Q Q o o S S 1. The first three (Class 1 to Class 3) class rules can be adjusted for your necessity. To add, edit or delete the class rule, please click the Edit link of that one. 2. After you click the Edit link, you will see the followin[...]

Vigor2925 Series User’s Guide 271 Available settings are explained as follows: Item Description ACT Check this box to invoke these settings. Hardware Acceleration Check this box to enable the hardware acceleration when such rule is applied. Ethernet Type Please specify which protocol (IPv4 or IPv6) will be used for this rule. Local Address Click [...]

Vigor2925 Series User’s Guide 272 By the way, you can set up to 20 rules for one Class. If you want to edit an existed rule, please select the radio button of that one and clic k Edit to open the rule edit page for modification. E E d d i i t t t t h h e e S S e e r r v v i i c c e e T T y y p p e e f f o o r r C C l l a a s s s s R R u u l l e e[...]

Vigor2925 Series User’s Guide 273 3. For adding a new service type, click Add to open the following pag e. Available settings are explained as follows: Item Description Service Name Type in a new service for your request. The maximum length of the name you can set is 11 characters. Service Type Choose the type (TCP, UDP or TCP/UDP or other) for t[...]

Vigor2925 Series User’s Guide 274 4 4 . . 1 1 1 1 A A p p p p l l i i c c a a t t i i o o n n s s Below shows the menu items for Applications. 4 4 . . 1 1 1 1 . . 1 1 D D y y n n a a m m i i c c D D N N S S The ISP often provides you with a dynamic IP address when you c onnect to the Internet via your ISP. It means that the public IP address assi[...]

Vigor2925 Series User’s Guide 275 2. In the DDNS setup menu, check Enable Dynamic DNS Setup . Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles and recover to factory settings. Enable Dynamic DNS Setup Check this box to enable DDNS function. View Log Display DDNS log status. Force Update Force[...]

Vigor2925 Series User’s Guide 276 Available settings are explained as follows: Item Description Enable Dynamic DNS Account Check this box to enable the current account. If you did check the box, you will see a ch eck mark appeared on the Active column of the previous web page in step 2). WAN Interface WAN1/WAN2/WAN3 First - While connecting, the [...]

Vigor2925 Series User’s Guide 277 Mail Extender If the mail server is defined with another name, please type the name in this area. Such mail server will be used as backup mail exchange. Determine Real WAN IP If a Vigor router is installed behind any NAT router, you can enable such function to locate the real WAN IP. When the WAN IP used by Vigor[...]

Vigor2925 Series User’s Guide 278 Each item is explained as follows: Item Description Set to Factory Default Clear all profiles and recover to factory settings. Enable Check the box to enable the selected profile. Index Click the number below Index to access into the setting page of schedule. Profile Display the name of the LAN DNS profile. Domai[...]

Vigor2925 Series User’s Guide 279 IP Address List The IP address listed here will be used for mapping with the domain name specified above. In general, one domain nam e maps with one IP address. If required, you can configure two IP addresses mapping with the same domain name.. Add – Click it to open a dialog to type the host’s IP address. On[...]

Vigor2925 Series User’s Guide 280 You have to set your time before set schedule. In System Maintenance>> Time and Date menu, press Inquire Time button to set the Vigor router’s clock to current time of your PC. The clock will reset once if you power down or reset the router. There is another way to set up time. You can inquiry an NTP serv[...]

Vigor2925 Series User’s Guide 281 Item Description Enable Schedule Setup Check to enable the schedule. Start Date (yyyy-mm-dd) Specify the starting date of the schedule. Start Time (hh:mm) Specify the starting time of the schedule. Duration Time (hh:mm) Specify the duration (or period) for the schedule. Action Specify which action Call Schedule s[...]

Vigor2925 Series User’s Guide 282 4 4 . . 1 1 1 1 . . 4 4 R R A A D D I I U U S S Remote Authentication Dial-In User Service (RADIUS) is a security authentication client/server protocol that supports authentication, authorization and accounting, which is widely used by Internet service providers. It is the most common method of authenticating and[...]

Vigor2925 Series User’s Guide 283 This page allows you to create several prof iles, enable the function and specify general settings for LDAP server. Available settings are explained as follows: Item Description Enable Check to enable such function. Bind Type There are three types of bind type supported. Simple Mode – Just simply do the bind au[...]

Vigor2925 Series User’s Guide 284 Regular DN Type this setting if Regular Mode is selected as Bind Type. Regular Password Specify a password if Regular Mode is selected as Bind Type. After finished the above settings, click OK button to save the settings. P P r r o o f f i i l l e e s s You can configure eight AD/LDAP profiles. These profiles wou[...]

Vigor2925 Series User’s Guide 285 Item Description Name Type a name for such profile. Common Name Identifier Type or edit the common name identifier for the LDAP server. The common name identifier for most LDAP server is “cn”. Base Distinguished Name / Group Distinguished Name Type or edit the distinguished name used to look up e ntries on th[...]

Vigor2925 Series User’s Guide 286 After setting Enable UPNP Service setting, an icon of IP Br oadband Connection on Router on W indows XP/Network Connections will appear . The connection status and control status will be able to be activated. The NA T T raversal of UPnP enables the multimedia features of your applications to operate. This has to [...]

Vigor2925 Series User’s Guide 287  Some Microsoft operating systems have found out the UPnP weaknesses and hence you need to ensure that you have applie d the latest service packs and patches.  Non-privileg ed users can control som e router functions, including removing and adding port mappings. The UPnP function dynamically adds port mappi[...]

Vigor2925 Series User’s Guide 288 4 4 . . 1 1 1 1 . . 8 8 W W a a k k e e o o n n L L A A N N A PC client on LAN can be woken up by the router it connects. When a user wants to wake up a specified PC through the router, he/she must type correct MAC address of the specified PC on this web page of Wake on LAN (WOL) of this router. In addition, such[...]

Vigor2925 Series User’s Guide 289 4 4 . . 1 1 1 1 . . 9 9 S S M M S S / / M M a a i i l l A A l l e e r r t t S S e e r r v v i i c c e e The function of SMS (Short Message Service)/Mail Alert is that Vigor router sends a message to user’s mobile or e-mail box through specified service provider to assist the user knowing the real-time abnormal [...]

Vigor2925 Series User’s Guide 290 Recipient Type the name of the one who will receive the SMS. Notify Use the drop down list to choose a message profile. The recipient will get the content stated in the message profile. You can click the Notify Profile link to define the content of the SMS. Schedule Type the schedule number that the SMS will be s[...]

Vigor2925 Series User’s Guide 291 Schedule Type the schedule number that the notification will be sent out. You can click the Schedule(1-15) link to define the schedule. After finishing all the settings here, please click OK to save the configuration. 4 4 . . 1 1 1 1 . . 1 1 0 0 B B o o n n j j o o u u r r Bonjour is a service discovery protocol [...]

Vigor2925 Series User’s Guide 292 2. Open the web browse, Firefox. If Bonjour and DNSSD have been installed, you can open the web page (DNSSD) and see the following results. 3. Open System Maintenance>>Management . Type a name (e.g., Dray _2925) as the Router Name and click OK . 4. Next, open A pplications>>Bonjour . Check the service[...]

Vigor2925 Series User’s Guide 293 5. Open the DNSSD page again. The available items will be changed as the follows. It means the Vigor router (based on Bonjour protocol) is ready to be used as a printer server, FTP server, SSH Server, Telnet Server, and HTTP Server. 6. Now, any page or document can be printed out through Vigor router (installed w[...]

Vigor2925 Series User’s Guide 294 4 4 . . 1 1 2 2 V V P P N N a a n n d d R R e e m m o o t t e e A A c c c c e e s s s s A Virtual Private Network (VPN) is the extension of a private network that encompasses links across shared or public networks like the Internet. In short, by VPN technolog y, you can send data between two computers across a sh[...]

Vigor2925 Series User’s Guide 295 mode, otherwise please choose Route Mode. Please choose a LAN-to-LAN Profile There are 32 VPN profiles for users to set. 2. When you finish the mode and profile selection, please click Next to open the following page.[...]

Vigor2925 Series User’s Guide 296 In this page, you have to select suitable VPN type for the VPN client profile. There are six types provided here. Different type will lead to different configuration page. After making the choices for the client profile, please click Next . You will see different configurations based on the selection(s) you made.[...]

Vigor2925 Series User’s Guide 297  When you choose IPSec , you will see the following graphic:  When you choose L2TP , you will see the following graphic:[...]

Vigor2925 Series User’s Guide 298  When you choose L2TP over IPSec (N ice to Have) or L2TP over IPSec (Must), you will see the following graphic: Available settings are explained as follows: Item Description Profile Name Type a name for such profile. The length of the file is limited to 10 characters. VPN Dial-Out Through Use the drop down men[...]

Vigor2925 Series User’s Guide 299 connecting, the router will use WAN1/WAN2/WAN3 as the only channel for VPN connection. WAN1 Only: Backup WAN2 - While connecting, the router will use WAN2 for VPN connection. If WAN2 fails, the router will use backup WAN1 interface instead. WAN2 Only: Backup WAN1 - While connecting, the router will use WAN1 for V[...]

Vigor2925 Series User’s Guide 300 3. After finishing the configuration, please click Next. The confirmation page will be shown as follows. If there is no problem, you can click one of the radio buttons listed on the page and click Finish to execute the next action. Available settings are explained as follows: Item Description Go to the VPN Connec[...]

Vigor2925 Series User’s Guide 301 4 4 . . 1 1 2 2 . . 2 2 V V P P N N S S e e r r v v e e r r W W i i z z a a r r d d Such wizard is used to configure VPN settings for VPN server. Such wizard will guide to set the LAN-to-LAN profile for VPN dial in connection (from client to server) step by step. 1. Open VPN and Remote Access >>VPN Server W[...]

Vigor2925 Series User’s Guide 302 Please choose a Dial-in User Accounts This item is available when you choose Remote Dial-in User (Teleworker) as VPN server mode. There are 32 VPN tunnels for users to set. Allowed Dial-in Type This item is available after you choose any one of dial-in user account profiles. Next, you have to select suitable dial[...]

Vigor2925 Series User’s Guide 303  When you check PPTP , you will see the following graphic:  When you check PPTP & IPSec & L2TP (three types) or PPTP&IPSec (two ty pes) or L2TP with Policy (Nice to Have/Must) , you will see the following graphic:[...]

Vigor2925 Series User’s Guide 304  When you check IPSec , you will see the following graphic: Available settings are explained as follows: Item Description Profile Name Type a name for such profile. The length of the file is limited to 10 characters. User Name This field is used to authenticate for connection when you select PPTP or L2TP with [...]

Vigor2925 Series User’s Guide 305 Remote Network IP Please type one LAN IP address (according to the real location of the remote host) for building VPN connection. Remote Network Mask Please type the network mask (according to the real location of the remote host) for building VPN connection. 3. After finishing the configuration, please click Nex[...]

Vigor2925 Series User’s Guide 306 4 4 . . 1 1 2 2 . . 3 3 R R e e m m o o t t e e A A c c c c e e s s s s C C o o n n t t r r o o l l Enable the necessary VPN service as you need. If you intend to run a VPN server inside your LAN, you should disable the VPN service of Vigor Router to allow VPN tunnel pass through, as well as the appropriate NAT s[...]

Vigor2925 Series User’s Guide 307 PAP or CHAP - Selecting this option means the router will attempt to authenticate dial-in users with the CHAP protocol first. If the dial-in user does not support this protocol, it will fall back to use the PAP protocol for authentication. Dial-In PPP Encryption (MPPE) Optional MPPE - This option represents that [...]

Vigor2925 Series User’s Guide 308 4 4 . . 1 1 2 2 . . 5 5 I I P P S S e e c c G G e e n n e e r r a a l l S S e e t t u u p p In IPSec General Setup, there are two major parts of configuration. There are two phases of IPSec.  Phase 1: negotiation of IKE para meters including encryption, hash, Diffie-Hellman parameter values, and lifetime to pr[...]

Vigor2925 Series User’s Guide 309 and IPSec tunnel. There are two methods offered by Vigor router for you to authenticate the incoming data coming from remote dial-in user, Certificate (X.509) and Pre-Shared Key . Certificate for Dial-in –Choose one of the local certificates from the drop down list. Pre-Shared Key- Specify a key for IKE authent[...]

Vigor2925 Series User’s Guide 310 4 4 . . 1 1 2 2 . . 6 6 I I P P S S e e c c P P e e e e r r I I d d e e n n t t i i t t y y To use digital certificate for p eer authentication in either LAN-to-LAN connection or Remote User Dial-In connection, here you may edit a table of peer certificate for selectio n. As shown below, the router provides 64 en[...]

Vigor2925 Series User’s Guide 311 Available settings are explained as follows: Item Description Profile Name Type the name of the profile. The maximum length of the name you can set is 32 characters. Enable this account Check it to enable such account profile. Accept Any Peer ID Click to accept any peer regardless of its identity. Accept Subject [...]

Vigor2925 Series User’s Guide 312 4 4 . . 1 1 2 2 . . 7 7 O O p p e e n n V V P P N N G G e e n n e e r r a a l l S S e e t t u u p p OpenVPN is a comprehensive SSL VPN software that combines OpenVPN server functions, enterprise management mech anism , simplified OpenVPN Connect User Interface and OpenVPN Client software pack age. It can work on [...]

Vigor2925 Series User’s Guide 313 4 4 . . 1 1 2 2 . . 8 8 R R e e m m o o t t e e D D i i a a l l - - i i n n U U s s e e r r You can manage remote access by maintaining a table of remote user profile, so that users can be authenticated to dial-in via VPN connection. You may set parameters including specified connection peer ID, connection type ([...]

Vigor2925 Series User’s Guide 314 Status Display the access state of th e specific dial-in user. The symbol V and X represent the specific dial-in user to be active and inactive, respectively. Click each index to edit one remote user profile. Each Dial-In Type requires you to fill the different corresponding fields on the right. If the fields gra[...]

Vigor2925 Series User’s Guide 315 below:  None - Do not apply the IPSec policy. Accordingly, the VPN connection employed the L2TP without IPSec policy can be viewed as one pure L2TP connection.  Nice to Have - Apply the IPSec policy first, if it is applicable during negotiation. Otherwise, the dial-in VPN connection becomes one pure L2TP co[...]

Vigor2925 Series User’s Guide 316 for the subnet you specified. IKE Authentication Method This group of fields is applicable for IPSec Tunnels and L2TP with IPSec Policy when you specify the IP address of the remote node. The only exception is Digital Signature (X.509) can be set when you select IPSec tunnel either with or without specify the IP [...]

Vigor2925 Series User’s Guide 317 The following shows profiles joined into VPN Load Balance and VPN Backup mechanism. Available settings are explained as follows: Item Description View All – Click it to display the LAN to LAN profiles. Online – Click it to display the online pr ofiles. Offline – Click it to display the offline profiles. Tru[...]

Vigor2925 Series User’s Guide 318 Status Online – means such LAN to LAN profile is in use. Offline – means such LAN to LAN profile isn’t in use even if the profile has been enabled. To edit each profile: 1. Click each index to edit each profile and you will get the following page. Each LAN-to-LAN profile includes 4 subgroups. If the fields [...]

Vigor2925 Series User’s Guide 319  WAN1 First/ WAN2 First/ WAN3 Firs t - While connecting, the router will use WAN1/WAN2/WAN3 as the first channel for VPN connection. If WAN1/WAN2/WAN3 fails, the router will use another WAN interface instead. WAN1 Only /WAN2 Only/WAN 3 Only - While connecting, the router will use WAN1/WAN2/WAN3 as the only cha[...]

Vigor2925 Series User’s Guide 320 Enable PING to keep alive - This function is to help the router to determine the status of IPSec VPN connection, especially useful in the case of abnormal VPN IPSec tunnel disruption. For details, please refer to the note below. Check to enable the transmission of PING packets to a specified IP address. Enable PI[...]

Vigor2925 Series User’s Guide 321 compression. Normally set to Yes to improve bandwidth utilization. IKE Authentication Method - This group of fields is applicable for IPSec Tunnels and L2TP with IPSec Policy.  Pre-Shared Key - Input 1-63 characters as pre-shared key.  Digital Signature (X.509) - Select one predefined Profiles set in the VP[...]

Vigor2925 Series User’s Guide 322 IKE phase 1 mode - Select from Main mode and Aggressive mode. The ultimate outcome is to exchange security proposals to create a protected secure channel. Main mode is more secure than Aggressive mode since more exchanges are done in a secure channel to set up the IPSec session. However, the Aggressive mode is fa[...]

Vigor2925 Series User’s Guide 323 Available settings are explained as follows: Item Description Dial-In Settings Allowed Dial-In Type - Determine the dial-in connection with different types.  PPTP - Allow the remote dial-in user to make a PPTP VPN connection through the Internet. You should set the User Name and Password of remote dial-in user[...]

Vigor2925 Series User’s Guide 324 dial-in VPN connection becomes one pure L2TP connection.  Must - Specify the IPSec policy to be definitely applied on the L2TP connection. Specify Remote VPN Gateway - You can specify the IP address of the remote dial-in user or peer ID (should be the same with the ID setting in dial-in type) by checking the b[...]

Vigor2925 Series User’s Guide 325  High- Encapsulating Security Payload (ESP) means payload (data) will be encrypted and authenticated. You may select encryption algorithm from Data Encryption Standard (DES), Triple DES (3DES), and AES. Gre over IPSec Settings Enable IPSec Dial-Out function GRE over IPSec : Check this box to verify data and tr[...]

Vigor2925 Series User’s Guide 326 RIP Direction - The option specifies the direction of RIP (Routing Information Protoc ol) packets. You can enable/disable one of direction here. Herein, we provide four options: TX/RX Both, TX Only, RX Only, and Disable. From first subnet to remote network, you have to do - If the remote network only allows you t[...]

Vigor2925 Series User’s Guide 327 4 4 . . 1 1 2 2 . . 1 1 0 0 V V P P N N T T R R U U N N K K M M a a n n a a g g e e m m e e n n t t VPN trunk includes four features - VPN Backup, VPN load balance, GRE over IPSec, and Binding tunnel policy. F F e e a a t t u u r r e e s s o o f f V V P P N N T T R R U U N N K K – – V V P P N N B B a a c c k [...]

Vigor2925 Series User’s Guide 328 Available settings are explained as follows: Item Description Backup Profile List Set to Factory Default - Click to clear all VPN TRUNK-VPN Backup mechanism profile. No – The order of VPN TRUNK-VPN Backup mechanism profile. Status - “v” means such profile is enabled; “x” means such profile is disabled. [...]

Vigor2925 Series User’s Guide 329 Member2 drop down list below. Advanced – This button is available only when LAN to LAN profile (or more) is created. Detailed information for this dialog, see later section - Advanced Load Balance and Backup . Load Balance Profile List Set to Factory Default - Click to clear all VPN TRUNK-VPN Load Balance mecha[...]

Vigor2925 Series User’s Guide 330 Detailed information for this dialog, see later section - Advanced Load Balance and Backup . General Setup Status - After choosing one of the profi le listed above, please click Enable to activate this profile. If you click Disable , the selected or current used VPN TRUNK-Backup/Load Balance mechanism profile wil[...]

Vigor2925 Series User’s Guide 331 profiles in LAN-to-LAN will be displayed in blue. Update- Click this button to save the changes to the Status (Enable or Disable), profile name, member1 or member2. Delete - Click this button to delete the selected VPN TRUNK profile. The corresponding members (LAN-to-LAN profiles) grouped in the deleted VPN TRUNK[...]

Vigor2925 Series User’s Guide 332 4. Take a look f or LAN-to-LAN profiles. Index 1 is chosen as Member1; index 2 is chosen as Member2. For such reason, LAN-to-LAN profiles of 1 and 2 will be expressed in red to indicate that they are fixed. If you delete the VPN TRUNK – VPN Backup/Load Balance mechanism profile, the selected LAN-to-LAN profiles[...]

Vigor2925 Series User’s Guide 333 A A d d v v a a n n c c e e d d L L o o a a d d B B a a l l a a n n c c e e a a n n d d B B a a c c k k u u p p After setting profiles for load balance, you can choose any one of t hem and click Advance for more detailed configuration. The windows for advanced load balance and backup are different. Refer to the f[...]

Vigor2925 Series User’s Guide 334 user to adjust suitable rate manually. There are 100 groups of rate ratio for Member1:Member2 (range from 1:99 to 99:1). VPN Load Balance Policy Below shows the algorithm for Load Balance. Edit – Click this radio button for assign a blank table for configuring Binding Tunnel. Insert after – Click this radio b[...]

Vigor2925 Series User’s Guide 335 Detail Information This field will display detailed information for Binding Tunnel Policy. Below shows a successful binding tunnel policy for load balance: Note : To configure a successful binding tunnel, you have to: Type Binding Src IP range (Start and End) and Binding Des IP range (Start and End). Choose TCP/U[...]

Vigor2925 Series User’s Guide 336 Item Description Profile Name List the backup profile name. ERD Mode ERD means “Environment Recovers Detection”. Normal – choose this mode to make all dial-out VPN TRUNK backup profiles being activated alternatively. Resume – when VPN connection breaks down or disconnects, Member 1 will be the top priorit[...]

Vigor2925 Series User’s Guide 337 VPN Server IP address). The VPN connection built by Backup Mode supports VPN backup function. Dial - Click this button to execute dial out function. Refresh Seconds - Choose the time for refresh the dial information among 5, 10, a nd 30. Refresh - Click this button to refresh the whole connection status. 4 4 . . [...]

Vigor2925 Series User’s Guide 338 click Generate again. Import Click this button to import a saved file as the certification information. Refresh Click this button to refresh the information listed below. View Click this button to view the detailed settings for certificate request. Delete Click this button to delete selected name with certificati[...]

Vigor2925 Series User’s Guide 339 IMPORT Vigor router allows you to generate a certificate request and submit it the CA server, then import it as “Local Certificate”. If you have already gotten a certificate fro m a third party, you may import it directly. The supported types are PKCS12 Certificate and Certificate with a private key. Click th[...]

Vigor2925 Series User’s Guide 340 Upload PKCS12 Certificate It allows users to import the certificate whose extensions are usually .pfx or .p12. And these certificates usually need passwords. Note: PKCS12 is a standard for storing private keys and certificates securely. It is used in (among other things ) Netscape and Microsoft Internet Explorer [...]

Vigor2925 Series User’s Guide 341 it and submit a request. A new certificate will be issued to you by the CA server. You can save it. D D e e l l e e t t e e Click this button to remove the selected certificate. 4 4 . . 1 1 3 3 . . 2 2 T T r r u u s s t t e e d d C C A A C C e e r r t t i i f f i i c c a a t t e e Trusted CA certificate lists thr[...]

Vigor2925 Series User’s Guide 342 4 4 . . 1 1 3 3 . . 3 3 C C e e r r t t i i f f i i c c a a t t e e B B a a c c k k u u p p Local certificate and Trusted CA certificate for this router can be saved within one file. Please click Backup on the following screen to save them. If you want to set encryption password for these certificates, please typ[...]

Vigor2925 Series User’s Guide 343 M M u u l l t t i i p p l l e e S S S S I I D D s s Vigor router supports four SSID settings for wireless connections. Each SSID can be defined with different name and download/upload rate for selecting by stations connected to the route r wirelessly. S S e e c c u u r r i i t t y y O O v v e e r r v v i i e e w [...]

Vigor2925 Series User’s Guide 344 In WPA-Personal, a pre-defined key is used for encryption during data transmission. WPA applies Temporal Key Integrity Protocol (TKIP) for data encryption while WPA2 applies AES. The WPA-Enterprise combines not only encry ption but also authentication. Since WEP has been proved vulnerable, you may consider using [...]

Vigor2925 Series User’s Guide 345 4 4 . . 1 1 3 3 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p By clicking the General Settings , a new web page will appear so that you could configure the SSID and the wireless channel. Please refer to the following figure for more information. Available settings are explained as follows: Item Descript[...]

Vigor2925 Series User’s Guide 346 Channel Means the channel of frequency of the wireless LAN. The default channel is 6. You may switch channel if the selected channel is under serious interference. If you have no idea of choosing the frequency, please select Auto to let system determine for you. Hide SSID Check it to prevent from wireless sniffin[...]

Vigor2925 Series User’s Guide 347 Schedule Set the wireless LAN to work at certain time interval only. You may choose up to 4 schedules out of the 15 schedules pre-defined in Applications >> Schedule setup. The default setting of this field is blank and the function will always work. After finishing all the settings here, please click OK to[...]

Vigor2925 Series User’s Guide 348 Available settings are explained as follows: Item Description Mode There are several modes provided for you to choose. Note: You should also set RADIUS Server simultaneously if 802.1x mode is selected. Disable - Turn off the encryption mechanism. WEP- Accepts only WEP clients and the encryption key should be ente[...]

Vigor2925 Series User’s Guide 349 server with 802.1X protocol. WPA2/802.1x Only- Accepts only WPA2 clients and the encryption key is obtained dynamically from RADIUS server with 802.1X protocol. Mixed (WPA+WPA2/802.1x only) - Accepts WPA and WPA2 clients simultaneously and the encryption key is obtained dynamically from RADIUS server with 802.1X [...]

Vigor2925 Series User’s Guide 350 Available settings are explained as follows: Item Description Enable Mac Address Filter Select to enable the MAC Address filter for wireless LAN identified with SSID 1 to 4 respectively. All the clients (expressed by MAC addresses) listed in the box can be grouped under different wireless LAN. For example, they c[...]

Vigor2925 Series User’s Guide 351 4 4 . . 1 1 4 4 . . 5 5 W W P P S S WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA2. Note: Such function is available for the wi reless station with WPS supported. It is the simples[...]

Vigor2925 Series User’s Guide 352  On the side of Vigor 2850 series which served as an AP, press WPS button once on the front panel of the router or click Start PBC on web configuration interface. On the side of a station with network card installed, press Start PBC button of network card.  If you want to use PIN code, you have to know the [...]

Vigor2925 Series User’s Guide 353 Below shows Wireless LAN>>WPS web page: Available settings are explained as follows: Item Description Enable WPS Check this box to enable WPS setting. WPS Status Display related system information for WPS. If the wireless security (encryption) function of the router is properly configured, you can see ‘Co[...]

Vigor2925 Series User’s Guide 354 4 4 . . 1 1 4 4 . . 6 6 W W D D S S WDS means Wireless Distribution System. It is a protocol for connecting two access points (AP) wirelessly. Usually, it can be used for the following application:  Provide bri dge traffic between two LANs throug h the air.  Extend the co verage range of a WLAN. To meet the[...]

Vigor2925 Series User’s Guide 355 Bridge mode, packets received from a WDS link will only be for warded to local wired or wireless hosts. In other words, only Repeater mode can do WDS-to-WDS packet forwarding. In the following examples, hosts connected to Bridge 1 or 3 can communicate with hosts connected to Bridge 2 through WDS links. However, h[...]

Vigor2925 Series User’s Guide 356 Available settings are explained as follows: Item Description Mode Choose the mode for WDS setting. Disable mode will not invoke any WDS setting. Bridge mode is designed to fulfill the first type of application. Repeater mode is for the second one. Security There are three types for security, Disable , WEP and Pr[...]

Vigor2925 Series User’s Guide 357 4 4 . . 1 1 4 4 . . 7 7 A A d d v v a a n n c c e e d d S S e e t t t t i i n n g g This page allows users to set advanced se ttings such as operation mode, channel bandwidth, guard interval, and aggregation MSDU for wireless data transmission. Available settings are explained as follows: Item Description Operati[...]

Vigor2925 Series User’s Guide 358 sizes. It is used for improving MAC layer’s performance for some brand’s clients. The default setting is Enable. Long Preamble This option is to define the length of the sync field in an 802.11 packet. Most modern wireless network uses short preamble with 56 bit sync field instead of long pream ble with 128 b[...]

Vigor2925 Series User’s Guide 359 4 4 . . 1 1 4 4 . . 8 8 W W M M M M C C o o n n f f i i g g u u r r a a t t i i o o n n WMM is an abbreviation of Wi-Fi Multimedia. It defines the priority levels for four access categories derived from 802.1d (prioritization tabs). T he categories are designed with specific types of traffic, voice, video, best e[...]

Vigor2925 Series User’s Guide 360 categories must be smaller; however, the difference between AC_BE and AC_BK categories must be greater. Txop It means transmission opportunity. For WMM categories of AC_VI and AC_VO that need higher priorities in data transmission, please set greater value for them to get highest transmission opportunity. Specify[...]

Vigor2925 Series User’s Guide 361 4 4 . . 1 1 4 4 . . 9 9 A A P P D D i i s s c c o o v v e e r r y y Vigor router can scan all regulatory channels and find working APs in the neighborhood. Based on the scanning result, users will know which channel is clean for usage. Also, it can be used to facilitate finding an AP for a WDS link. Notice that d[...]

Vigor2925 Series User’s Guide 362 4 4 . . 1 1 4 4 . . 1 1 0 0 S S t t a a t t i i o o n n L L i i s s t t Station List provides the knowledge of connecting wireless clients now along with its status code. There is a code summary belo w for explanation. For convenient Access C ontrol , you can select a WLAN station and click Add to Access Control [...]

Vigor2925 Series User’s Guide 363 4 4 . . 1 1 5 5 S S S S L L V V P P N N An SSL VPN (Secure Sockets Layer virtual private network) is a form of VPN that can be used with a standard Web browser. There are two benefits that SSL VPN provides:  It is not necessary for users to preinstall VPN client software for executing SSL VPN connection.  T[...]

Vigor2925 Series User’s Guide 364 Encryption Key Algorithm Choose the encryption level for the data connection in SSL VPN server. After finishing all the settings here, please click OK to save the configuration. 4 4 . . 1 1 5 5 . . 2 2 S S S S L L W W e e b b P P r r o o x x y y SSL Web Proxy will allow the remote users to access the internal web[...]

Vigor2925 Series User’s Guide 365 URL Type the address (function variation or IP address) or path of the proxy server. Host IP Address If you type function variation as URL, you have to t ype corresponding IP address in this filed. Such field must match with URL setting. Access Method There are three modes for you to choose. Disable – the profi[...]

Vigor2925 Series User’s Guide 366 To create a new SSL application profile: 1. Click number link under Index filed to s et detailed configuration. 2. The following page will appear. Available settings are explained as follows: Item Description Enable Application Server Check the box to enable such profile. Application Name Type a name for such app[...]

Vigor2925 Series User’s Guide 367 Samba Application – It allows you to access and control a remote PC through Samba service. IP Address If you choose VNC or RDP, you have to type the IP address for this protocol. Port If you choose VNC or RDP, you have to specify the port used for this protocol. The default setting is 5900. Idle Timeout If you [...]

Vigor2925 Series User’s Guide 368 4 4 . . 1 1 5 5 . . 4 4 U U s s e e r r A A c c c c o o u u n n t t With SSL VPN, Vigor2925 series let teleworkers ha ve convenient and simple rem ote access to central site VPN. The teleworkers do not need to install any VPN software manually. From regular web browser, you can establish VPN connection back to yo[...]

Vigor2925 Series User’s Guide 369 Available settings are explained as follows: Item Description User account and Authentication Enable this account - Check the box to enable this function. Idle Timeout- If the dial-in user is idle over the limitation of the timer, the router will drop this connection. By default, the Idle Timeout is set to 300 se[...]

Vigor2925 Series User’s Guide 370 Item Description  Must - Specify the IPSec policy to be definitely applied on the L2TP connection. SSL Tunnel - It allows the remote dial-in user to make an SSL VPN Tunnel connection through Internet, suitable for the application through network accessing (e.g., PPTP/L2TP/IPSec) If you check this box, the func[...]

Vigor2925 Series User’s Guide 371 Item Description (mOTP) PIN Code – Type the code for authentication (e.g, 1234). Secret – Use the 32 digit-secret number generated by mOTP in the mobile phone (e.g., e759bb6f0e94c7 ab4fe6). IKE Authentication Method This group of fields is applicable for IPSec Tunnels and L2TP with IPSec Policy when you speci[...]

Vigor2925 Series User’s Guide 372 4 4 . . 1 1 5 5 . . 5 5 U U s s e e r r G G r r o o u u p p There are 10 user group profiles which can be created for authentication by LDAP server. Such profiles will be used by applications such as User Manageme nt, VPN and etc. Each item is explained as follows: Item Description Set to Factory Default Click to[...]

Vigor2925 Series User’s Guide 373 Available settings are explained as follows: Item Description Enable Check this box to enable such profile. Group Name Type a name for such profile. The length of the name is limited to 23 characters. Access Authority Specify the authority for such profile. At present, Vigor router allows you to create SSL Web Pr[...]

Vigor2925 Series User’s Guide 374 4 4 . . 1 1 5 5 . . 6 6 O O n n l l i i n n e e U U s s e e r r S S t t a a t t u u s s If you have finished the configuration of SSL Web Proxy (server), users can find out corresponding settings when they access into DrayTek SSL VPN portal interface. Next, users can open SSL VPN>> Online Status to view log[...]

Vigor2925 Series User’s Guide 375 4 4 . . 1 1 6 6 U U S S B B A A p p p p l l i i c c a a t t i i o o n n USB storage disk connected on Vigor router can be regarded as a server. By way of Vigor router, clients on LAN can access, write and read data stored in USB storage disk with different applications. After setting the configuration in USB Appl[...]

Vigor2925 Series User’s Guide 376 up to 6 FTP sessions connecting to USB storage disk at one time. Default Charset - At present, Vigor router supports four types of character sets. Default Charset is for English based file name. Samba Service Settings Click Enable to invoke samba service via the router. Access Mode LAN Only – Users coming from [...]

Vigor2925 Series User’s Guide 377 Available settings are explained as follows: Item Description FTP/Samba User Enable – Click this button to activate this profile (account) for FTP service or Samba User service. Later, the user can use the username specified in this page to login into FTP server. Disable – Click this button to disable such pr[...]

Vigor2925 Series User’s Guide 378 Only “/” can be used in such case. You can click to open the following dialog to add any new folder which can be specified as the Home Folder. Access Rule It determines the authority for such profile. Any user, who uses such profile for accessing into USB storage disk, must follow the rule specified here. Fil[...]

Vigor2925 Series User’s Guide 379 4 4 . . 1 1 6 6 . . 3 3 F F i i l l e e E E x x p p l l o o r r e e r r File Explorer offers an easy way for users to view and manage the content of USB storage disk connected on Vigor router. Available settings are explained as follows: Item Description Refresh Click this icon to refresh files list. Back Click t[...]

Vigor2925 Series User’s Guide 380 Available settings are explained as follows: Item Description Connection Status If there is no USB storage disk connected to Vigor router, “ No Disk Connected ” will be shown here. Disk Capacity It displays the total capacity of the USB storage disk. Free Capacity It displays the free space of the USB storage[...]

Vigor2925 Series User’s Guide 381 4 4 . . 1 1 6 6 . . 5 5 T T e e m m p p e e r r a a t t u u r r e e S S e e n n s s o o r r A USB Thermometer can be attached to Vigor router to monitor the environmental temperature. If the temperature is higher the upper limit or lower than the lower limit, an alert would be sent out for notification. T T e e m[...]

Vigor2925 Series User’s Guide 382 T T e e m m p p e e r r a a t t u u r r e e C C h h a a r r t t Below shows an example of temperature graph: 4 4 . . 1 1 6 6 . . 6 6 M M o o d d e e m m S S u u p p p p o o r r t t L L i i s s t t Such page provides the information about the brand nam e and model name of the USB modems which are supported by Vigo[...]

Vigor2925 Series User’s Guide 383 4 4 . . 1 1 7 7 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration: System Status, TR-069, Administrator Password, User Password, Login Page Greeting, Configuration Backup, Syslog /Mail Alert, Time and Da[...]

Vigor2925 Series User’s Guide 384 Available settings are explained as follows: Item Description Model Name Display the model name of the router. Firmware Version Display the firmware version of the router. Build Date/Time Display the date and time of the current firmware build. LAN MAC Address - Display the MAC address of the LAN Interface. IP Ad[...]

Vigor2925 Series User’s Guide 385 4 4 . . 1 1 7 7 . . 2 2 T T R R - - 0 0 6 6 9 9 This device supports TR-069 standard. It is very convenient for an administrator to m anage a TR-069 device through an Auto Configuration Server, e.g., VigorACS. Available settings are explained as follows: Item Description ACS Server On Choose the interface for the[...]

Vigor2925 Series User’s Guide 386 click Disable to close the mechanism of notification. STUN Settings The default is Disable . If you click Enable , please type the relational settings listed below: Server IP – Type the IP address of the STUN server. Server Port – Type the port number of the STUN server. Minimum Keep Alive Period – If STUN [...]

Vigor2925 Series User’s Guide 387 4 4 . . 1 1 7 7 . . 4 4 U U s s e e r r P P a a s s s s w w o o r r d d This page allows you to set new password for user operation. Available settings are explained as follows: Item Description Enable User Mode for simple web configuration After checking this box, you can access into the web user interface with [...]

Vigor2925 Series User’s Guide 388 3. The following screen will appear. Simply click OK . 4. Log out Vigor router web user interface by clicking the Logout button. 5. The following window will be open to ask for username and password. Type the new user password in the filed of Password and click Login .[...]

Vigor2925 Series User’s Guide 389 6. The main screen with User Mode will be shown as follows. Settings to be configured in User Mode will be less than settings in Admin Mode. Only basic configuration settings will be available in User Mode. Note : Setting in User Mode can be configured as same as in Admin Mode.[...]

Vigor2925 Series User’s Guide 390 4 4 . . 1 1 7 7 . . 5 5 L L o o g g i i n n P P a a g g e e G G r r e e e e t t i i n n g g When you want to access into the web user interface of Vigor router, the system will ask you to offer username and password first. At that moment, the background of the web page is blank and no heading will be displa yed o[...]

Vigor2925 Series User’s Guide 391 Below shows an example of login customiza tion with the information typed in L ogin Description and Bulletin.[...]

Vigor2925 Series User’s Guide 392 4 4 . . 1 1 7 7 . . 6 6 C C o o n n f f i i g g u u r r a a t t i i o o n n B B a a c c k k u u p p B B a a c c k k u u p p t t h h e e C C o o n n f f i i g g u u r r a a t t i i o o n n Follow the steps below to backup your configuration. 1. Go to System Maintenance >> Configuration Backup . The following[...]

Vigor2925 Series User’s Guide 393 4. Click Save button, the configuration will download a utomatically to your computer as a file named config.cfg . The above example is using W indows platform for demonstrating exam ples. The Mac or Linux platform will appear dif ferent windows, but the backup function is still available. Note: Backup for Certif[...]

Vigor2925 Series User’s Guide 394 4 4 . . 1 1 7 7 . . 7 7 S S y y s s l l o o g g / / M M a a i i l l A A l l e e r r t t SysLog function is provided for users to monitor router. There is no bother to directly get into the Web user interface of the router or borrow debug equipments. Available settings are explained as follows: Item Description Sy[...]

Vigor2925 Series User’s Guide 395 AlertLog Setup Check Enable to activate function of alert log. AlertLog Port - Type the port number for alert log. The default setting is 514. Mail Alert Setup Check Enable to activate function of mail alert. Send a test e-mail - Make a simple test for the e-mail address specified in this page. Please assign the [...]

Vigor2925 Series User’s Guide 396[...]

Vigor2925 Series User’s Guide 397 4 4 . . 1 1 7 7 . . 8 8 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Available settings are explained as follows: Item Description Current System Time Click Inquire Time to get the current time. Use Browser Time Select this option to us[...]

Vigor2925 Series User’s Guide 398 4 4 . . 1 1 7 7 . . 9 9 S S N N M M P P This page allows you to configure settings for SNMP and SNMPV3 services. The SNMPv3 is more secure than SNMP through the encryption method (support AES and DES) and authentication method (support MD 5 and S HA) for the management needs. Available settings are explained as f[...]

Vigor2925 Series User’s Guide 399 Notification Host IP (IPv6) Set the IPv6 address of the host that will receive the trap community. Trap Timeout The default setting is 10 seconds. Enable SNMPV3 Agent Check it to enable this function. USM User USM means user-based security mode. Type a username which will be used for authentication. The maximum l[...]

Vigor2925 Series User’s Guide 400 4 4 . . 1 1 7 7 . . 1 1 0 0 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the settings for access control, access list and port setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session. The management pages for IPv4 an[...]

Vigor2925 Series User’s Guide 401 numbers for the Telnet, HTTP and FTP servers. Default Ports - Check to use standard port numbers for the Telnet and HTTP servers. After finished the above settings, click OK to save the configuration. F F o o r r I I P P v v 6 6 Available settings are explained as follows: Item Description Management Access Contr[...]

Vigor2925 Series User’s Guide 402 4 4 . . 1 1 7 7 . . 1 1 1 1 R R e e b b o o o o t t S S y y s s t t e e m m The Web user interface may be used to restart your router. Click Reboot System from System Maintenance to open the following page. Index (1-15) in Schedule Setup - You can type in four sets of time schedule for performing system reboot. A[...]

Vigor2925 Series User’s Guide 403 4 4 . . 1 1 7 7 . . 1 1 2 2 F F i i r r m m w w a a r r e e U U p p g g r r a a d d e e Before upgrading your router firmware, you need to i nstall the Router Tools. The Firmware Upgrade Utility is included in the tools. The following web page will guide you to upgrade firmware by using an exam ple. Note that thi[...]

Vigor2925 Series User’s Guide 404 4 4 . . 1 1 7 7 . . 1 1 3 3 A A c c t t i i v v a a t t i i o o n n There are three ways to activate WCF on vigor router, using Service Activation Wizard , by means of CSM>>Web Content Filter Profile or via System Maintenance>>Activation . After you have finished the setting profiles for WCF (refer to[...]

Vigor2925 Series User’s Guide 405 Below shows the successful activation of Web Content Filter: 4 4 . . 1 1 8 8 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router. Below shows the menu items for Diagnostics.[...]

Vigor2925 Series User’s Guide 406 4 4 . . 1 1 8 8 . . 1 1 D D i i a a l l - - o o u u t t T T r r i i g g g g e e r r i i n n g g Click Diagnostics and click Dial-out Triggering to open the web page. The internet connection (e.g., PPPoE) is triggered by a package sending from the source IP address. Available settings are explained as follows: Ite[...]

Vigor2925 Series User’s Guide 407 4 4 . . 1 1 8 8 . . 2 2 R R o o u u t t i i n n g g T T a a b b l l e e Click Diagnostics and click Routing Table to open t he web page. Available settings are explained as follows: Item Description Refresh Click it to reload the page.[...]

Vigor2925 Series User’s Guide 408 4 4 . . 1 1 8 8 . . 3 3 A A R R P P C C a a c c h h e e T T a a b b l l e e Click Diagnostics and click ARP Cache Table to view the content of the ARP (Address Resolution Protocol) cache held in the router. Th e table shows a mapping between an Ethernet hardware address (MAC Address) and an IP address. Available [...]

Vigor2925 Series User’s Guide 409 4 4 . . 1 1 8 8 . . 5 5 D D H H C C P P T T a a b b l l e e The facility provides information on IP address assignments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Available settings are explained as f[...]

Vigor2925 Series User’s Guide 410 4 4 . . 1 1 8 8 . . 6 6 N N A A T T S S e e s s s s i i o o n n s s T T a a b b l l e e Click Diagnostics and click NAT Sessions Table to open the list page. Available settings are explained as follows: Item Description Private IP:Port It indicates the source IP address and port of local PC. #Pseudo Port It indic[...]

Vigor2925 Series User’s Guide 411 4 4 . . 1 1 8 8 . . 7 7 P P i i n n g g D D i i a a g g n n o o s s i i s s Click Diagnostics and click Ping Diagnosis to pen the web page. Available settings are explained as follows: Item Description IPV4 /IPV6 Choose the interface for such function. Ping through Use the drop down list to choose the WAN interfa[...]

Vigor2925 Series User’s Guide 412 Run Click this button to start the ping work. The result will be displayed on the screen. Clear Click this link to remove the result on the window. 4 4 . . 1 1 8 8 . . 8 8 D D a a t t a a F F l l o o w w M M o o n n i i t t o o r r This page displays the running procedure for the IP address monitored and refreshe[...]

Vigor2925 Series User’s Guide 413 Enable Data Flow Monitor Check this box to enable this function. Refresh Seconds Use the drop down list to choose the time interval of refreshing data flow that will be done by the system automatically. Refresh Click this link to refresh this page manually. Index Display the number of the data flow. IP Address Di[...]

Vigor2925 Series User’s Guide 414 4 4 . . 1 1 8 8 . . 9 9 T T r r a a f f f f i i c c G G r r a a p p h h Click Diagnostics and click Traffic Graph to pen the web page. Choose WAN1/WAN2/WAN3 Bandwidth, Sessions, daily or weekly for viewing different traffic graph. Click Reset to zero the accumulated RX/TX (received and transmitted) data of WAN. C[...]

Vigor2925 Series User’s Guide 415 4 4 . . 1 1 8 8 . . 1 1 0 0 T T r r a a c c e e R R o o u u t t e e Click Diagnostics and click Trace Route to open the web page. This page allows you to trace the routes from router to the host. Simply type the IP address of the host in the box and click Run . The result of route trace will be shown on the scree[...]

Vigor2925 Series User’s Guide 416 Protocol Use the drop down list to choose the protocol that you want to ping through. Host/IP Address It indicates the IP address of the host. Trace Host/IP Address It indicates the IPv6 address of the host. Run Click this button to start route tracing work. Clear Click this link to remove the result on the windo[...]

Vigor2925 Series User’s Guide 417 Stop record when fulls – when the capacity of syslog is full, the system will stop recording. Always record the new event – only the newest events will be recorded by the system. Time Display the time of the event occurred. Message Display the information for each event. F F o o r r U U S S B B S S y y s s l [...]

Vigor2925 Series User’s Guide 418 Available settings are explained as follows: Item Description Refresh Click this link to refresh this page manually. 4 4 . . 1 1 9 9 E E x x t t e e r r n n a a l l D D e e v v i i c c e e s s Vigor router can be used to connect with many types of external devices. In order to control or manage the external devic[...]

Vigor2925 Series User’s Guide 419 When you finished the configuration, click OK to save it. Note : Only DrayTek products can be detected by this function. 4 4 . . 1 1 9 9 . . 2 2 A A c c c c e e s s s s P P o o i i n n t t D D e e v v i i c c e e s s Vigor2925 series can be treated as a server, named APM server, which manages access point devices[...]

Vigor2925 Series User’s Guide 420 Clear Click it to remove all the setti ngs modified in this pa ge. Refresh Click it to refresh current page. Index Click the number index to open the settings page of the device. Device Name Display the name of the device. IP Address Display the IP address of the device. SSID Display the SSID configure by the dev[...]

Vigor2925 Series User’s Guide 421 Set to Factory Default Clear all of the settings and return to factory default settings. Profile Name Display the name of the profile scanned by Vigor router. Main SSID Display the SSID used by the Vigor router. Security Display the mode used by the Vigor router. Multi-SSID Display if the multi-SSID function is e[...]

Vigor2925 Series User’s Guide 422 click to move it to the ri ght field of Selected Device. Then click Apply. The selected device now will be applied with the selected WLAN profile. To edit a WALN profile, follow the step listed below: 1. Check the box of the entry that you want to edit. Then, click the Edit button. 2. The following page will appe[...]

Vigor2925 Series User’s Guide 423 Lower down the value may degrade range and throughput of wireless. Cancel Cancel the setting configured on this page . Next Access into the next setting page. 3. Type the required information and click Next to open next page. Yo u can configure the settings for SSID1, SSID2, SSID3 and SSID4 respectively. Availabl[...]

Vigor2925 Series User’s Guide 424 wired PC in LAN. Isolate – From Member - Check this box to make the wireless clients (stations) with the same SSID not accessing for each other. Security Setting Disable – There are several modes provided for you to choose. WPA Algorithm – Select TKIP , AES or TKIP/AES as the algorithm for WP A. Such featur[...]

Vigor2925 Series User’s Guide 425 Bandwidth Limit Status – Click Enable to enable the function of bandwidth limit. Upload – Type the value as the uploading rate of data transmission. Auto Adjustment – Click Enable to make the router manage the bandwidth limit automatically. Download - Type the value as the downloading rate of data transmiss[...]

Vigor2925 Series User’s Guide 426 T T r r o o u u b b l l e e S S h h o o o o t t i i n n g g This section will guide you to solve abnormal s ituations if you cannot access into the Internet after installing the router and finishing the web configuration. Please follow sections below to check your basic installation status stage by stage.  Che[...]

Vigor2925 Series User’s Guide 427 5 5 . . 2 2 C C h h e e c c k k i i n n g g I I f f t t h h e e N N e e t t w w o o r r k k C C o o n n n n e e c c t t i i o o n n S S e e t t t t i i n n g g s s o o n n Y Y o o u u r r C C o o m m p p u u t t e e r r I I s s O O K K o o r r N N o o t t Sometimes the link failure occurs due to the wrong network[...]

Vigor2925 Series User’s Guide 428 4. Select Obtain an IP address automatically and Obtain DNS server address automatically . F F o o r r M M a a c c O O S S 1. Double click on the current used Mac OS on the desktop. 2. Open the Application folder and get into Network . 3. On the Network screen, select Using DHCP from the drop down list of Configu[...]

Vigor2925 Series User’s Guide 429 5 5 . . 3 3 P P i i n n g g i i n n g g t t h h e e R R o o u u t t e e r r f f r r o o m m Y Y o o u u r r C C o o m m p p u u t t e e r r The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most import[...]

Vigor2925 Series User’s Guide 430 5 5 . . 4 4 C C h h e e c c k k i i n n g g I I f f t t h h e e I I S S P P S S e e t t t t i i n n g g s s a a r r e e O O K K o o r r N N o o t t Open WAN >> Internet Access page and then check whether the ISP settings are set correctly. Click Details Page of WAN1-WAN3 to review the settings that you conf[...]

Vigor2925 Series User’s Guide 431 T T r r a a n n s s m m i i s s s s i i o o n n R R a a t t e e i i s s n n o o t t f f a a s s t t e e n n o o u u g g h h Please connect your Notebook with 3G USB Modem to test the connection speed to verify if the problem is caused by Vigor2925. In addition, please refer to the manual of 3G USB Modem for LED S[...]

Vigor2925 Series User’s Guide 432 H H a a r r d d w w a a r r e e R R e e s s e e t t While the router is running (ACT LED blinking), press the Factory Reset button and hold for more than 5 seconds. When you see the ACT LED blinks rapidly, please release the button. Then, the router will restart with the default configuration. After restore the f[...]