Emerson MMI-20019043 manuel d'utilisation

Configuration and Use Manual MMI-20019043, Rev AA March 2012 Micro Motion ® Model 2700 Transmitters with Analog Outputs Configuration and Use Manual[...]

Safety messages Safety messages are provided throughout this manual to protect personnel and equipment. Read each safety message carefully before proceeding to the next step. Micro Motion customer service Location Telephone number Email U.S.A. 800-522-MASS (800-522-6277) (toll free) flow.support@emerson.com Canada and Latin America +1 303-527-5200 [...]

Contents Part I Getting Started Chapter 1 Before you begin .............................................................................................................3 1.1 About this manual .........................................................................................................................3 1.2 Transmitter model code ........[...]

4.5 Configure density measurement ................................................................................................. 45 4.5.1 Configure Density Measurement Unit ........................................................................... 46 4.5.2 Configure slug flow parameters ..........................................................[...]

5.6.6 Configure Sensor Liner Material .................................................................................... 97 5.6.7 Configure Sensor Flange Type ....................................................................................... 98 Chapter 6 Integrate the meter with the control system ............................................[...]

9.4.3 View and acknowledge alerts using ProLink III ............................................................. 156 9.4.4 View alarms using the Field Communicator ................................................................ 156 9.4.5 Alarm data in transmitter memory .............................................................................[...]

12.3 Flow measurement problems .................................................................................................... 220 12.4 Density measurement problems ............................................................................................... 222 12.5 Temperature measurement problems ..........................................[...]

B.2.2 Make a service port connection ................................................................................... 275 B.2.3 Make a HART/Bell 202 connection .............................................................................. 276 B.2.4 Make a HART/RS-485 connection ....................................................................[...]

Part I Getting Started Chapters covered in this part: • Before you begin • Quick start Getting Started Configuration and Use Manual 1[...]

Getting Started 2 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

1 Before you begin Topics covered in this chapter: • About this manual • Transmitter model code • Communications tools and protocols • Additional documentation and resources 1.1 About this manual This manual provides information to help you configure, commission, use, maintain, and troubleshoot the Micro Motion Model 2700 transmitter. Impor[...]

Communications tools, protocols, and related information Table 1-1: Communica- tions tool Supported protocols Scope In this manual For more information Display Not applicable Basic configuration and commissioning Complete user informa- tion. See Appendix A . Not applicable ProLink II • HART/RS-485 • HART/Bell 202 • Modbus/RS-485 • Service p[...]

Additional documentation and resources (continued) Table 1-2: Topic Document Transmitter installation Micro Motion Model 1700 and Model 2700 Transmitters: Installation Manual Hazardous area installa- tion See the approval documentation shipped with the transmitter, or download the appropriate documentation from the Micro Motion web site at www.micr[...]

Before you begin 6 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

2 Quick start Topics covered in this chapter: • Power up the transmitter • Check flowmeter status • Make a startup connection to the transmitter • Characterize the flowmeter (if required) • Verify mass flow measurement • Verify the zero 2.1 Power up the transmitter The transmitter must be powered up for all configuration and commissioni[...]

1. Wait approximately 10 seconds for the power-up sequence to complete. Immediately after power-up, the transmitter runs through diagnostic routines and checks for error conditions. During the power-up sequence, Alarm A009 is active. This alarm should clear automatically when the power-up sequence is complete. 2. Check the status LED on the transmi[...]

2.3 Make a startup connection to the transmitter For all configuration tools except the display, you must have an active connection to the transmitter to configure the transmitter. Follow this procedure to make your first connection to the transmitter. Identify the connection type to use, and follow the instructions for that connection type in the [...]

2.4 Characterize the flowmeter (if required) Display Not available ProLink II • ProLink > Configuration > Device > Sensor Type • ProLink > Configuration > Flow • ProLink > Configuration > Density • ProLink > Configuration > T Series ProLink III Device Tools > Calibration Data Field Communicator Configure > M[...]

• Older curved-tube sensors (all sensors except T-Series): see Figure 2-1 • Newer curved-tube sensors (all sensors except T-Series): see Figure 2-2 • Older straight-tube sensors (T-Series): see Figure 2-3 • Newer straight-tube sensors (T-Series): see Figure 2-4 Tag on older curved-tube sensors (all sensors except T-Series) Figure 2-1: Tag o[...]

Tag on older straight-tube sensor (T-Series) Figure 2-3: Tag on newer straight-tube sensor (T-Series) Figure 2-4: Density calibration parameters (D1, D2, K1, K2, FD, DT, TC) If your sensor tag does not show a D1 or D2 value: • For D1 , enter the Dens A or D1 value from the calibration certificate. This value is the line-condition density of the l[...]

If your sensor tag does not show a DT or TC value, enter the last 3 digits of the density calibration factor. In the sample tag, this value is shown as 4.44 (see Figure 2-1 ). Flow calibration parameters (FCF, FT) Two separate values are used to describe flow calibration: a 6-character FCF value and a 4- character FT value. Both values contain deci[...]

• Review the troubleshooting suggestions for flow measurement issues. See Section 12.3 . 2.6 Verify the zero Verifying the zero helps you determine if the stored zero value is appropriate to your installation, or if a field zero can improve measurement accuracy. The zero verification procedure analyzes the Live Zero value under conditions of zero[...]

3. If the zero verification procedure fails: a. Confirm that the sensor is completely blocked in, that flow has stopped, and that the sensor is completely full of process fluid. b. Verify that the process fluid is not flashing or condensing, and that it does not contain particles that can settle out. c. Repeat the zero verification procedure. d. If[...]

3. If the zero verification procedure fails: a. Confirm that the sensor is completely blocked in, that flow has stopped, and that the sensor is completely full of process fluid. b. Verify that the process fluid is not flashing or condensing, and that it does not contain particles that can settle out. c. Repeat the zero verification procedure. d. If[...]

Part II Configuration and commissioning Chapters covered in this part: • Introduction to configuration and commissioning • Configure process measurement • Configure device options and preferences • Integrate the meter with the control system • Completing the configuration • Set up the Weights & Measures application Configuration and[...]

Configuration and commissioning 18 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

3 Introduction to configuration and commissioning Topics covered in this chapter: • Configuration flowchart • Default values and ranges • Enable access to the off-line menu of the display • Disable write-protection on the transmitter configuration • Restore the factory configuration 3.1 Configuration flowchart Use the following flowchart [...]

Configuration flowchart Figure 3-1: Integrate device with control system Configure device options and preferences Configure process measurement Configure mass flow measurement Configure volume flow meaurement Configure temperature measurement V olume flow type Liquid Gas Define gas properties Configure display parameters Configure fault handling pa[...]

3.2 Default values and ranges See Section E.1 to view the default values and ranges for the most commonly used parameters. 3.3 Enable access to the off-line menu of the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY ProLink II ProLink > Configuration > Display > Display Options ProLink III Device Tools > Configuration &[...]

Tip Write-protecting the transmitter prevents accidental changes to configuration. It does not prevent normal operational use. You can always disable write-protection, perform any required configuration changes, then re-enable write-protection. 3.5 Restore the factory configuration Display Not available ProLink II ProLink > Configuration > De[...]

4 Configure process measurement Topics covered in this chapter: • Configure mass flow measurement • Configure volume flow measurement for liquid applications • Configure gas standard volume (GSV) flow measurement • Configure Flow Direction • Configure density measurement • Configure temperature measurement • Configure the petroleum me[...]

Tip If the measurement unit you want to use is not available, you can define a special measurement unit. Options for Mass Flow Measurement Unit The transmitter provides a standard set of measurement units for Mass Flow Measurement Unit , plus one user-defined special measurement unit. Different communications tools may use different labels for the [...]

Define a special measurement unit for mass flow Display Not available ProLink II ProLink > Configuration > Special Units ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Mass Special Units Overview A specia[...]

a. 1 lb/sec = 16 oz/sec b. Mass Flow Conversion Factor = 1/16 = 0.0625 4. Set Mass Flow Conversion Factor to 0.0625 . 5. Set Mass Flow Label to oz/sec . 6. Set Mass Total Label to oz . 4.1.2 Configure Flow Damping Display Not available ProLink II ProLink > Configuration > Flow > Flow Damp ProLink III Device Tools > Configuration > Pr[...]

• In general, lower damping values are preferable because there is less chance of data loss, and less lag time between the actual measurement and the reported value. • For gas applications, Micro Motion recommends setting Flow Damping to 2.56 or higher. The value you enter is automatically rounded down to the nearest valid value. Valid damping [...]

Procedure Set Mass Flow Cutoff to the value you want to use. The default value for Mass Flow Cutoff is 0.0 g/sec or a sensor-specific value set at the factory. The recommended setting is 0.05% of the sensor's rated maximum flow rate or a value below the highest expected flow rate. Do not set Mass Flow Cutoff to 0.0 g/sec. Effect of Mass Flow C[...]

- The frequency output will report the actual flow rate, and the actual flow rate will be used in all internal processing. • If the mass flow rate drops below 10 g/sec, both outputs will report zero flow, and 0 will be used in all internal processing. 4.2 Configure volume flow measurement for liquid applications The volume flow measurement parame[...]

Procedure Set Volume Flow Type to Liquid . 4.2.2 Configure Volume Flow Measurement Unit for liquid applications Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > VOL ProLink II ProLink > Configuration > Flow > Vol Flow Units ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure[...]

Options for Volume Flow Measurement Unit for liquid applications (continued) Table 4-3: Unit description Label Display ProLink II ProLink III Field Communica- tor Cubic feet per hour CUFT/H ft3/hr ft3/hr Cuft/h Cubic feet per day CUFT/D ft3/day ft3/day Cuft/d Cubic meters per second M3/S m3/sec m3/sec Cum/s Cubic meters per minute M3/MIN m3/min m3/[...]

Define a special measurement unit for volume flow Display Not available ProLink II ProLink > Configuration > Special Units ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Volume Special Units Overview A sp[...]

a. 1 gal/sec = 8 pints/sec b. Volume Flow Conversion Factor = 1/8 = 0.1250 4. Set Volume Flow Conversion Factor to 0.1250 . 5. Set Volume Flow Label to pints/sec . 6. Set Volume Total Label to pints . 4.2.3 Configure Volume Flow Cutoff Display Not available ProLink II ProLink > Configuration > Flow > Vol Flow Cutoff ProLink III Device Tool[...]

Result: If the volume flow rate drops below 15 l/sec, volume flow will be reported as 0, and 0 will be used in all internal processing. Example: Cutoff interaction with AO Cutoff higher than Volume Flow Cutoff Configuration: • mA Output Process Variable : Volume Flow Rate • Frequency Output Process Variable : Volume Flow Rate • AO Cutoff : 15[...]

4.3.1 Configure Volume Flow Type for gas applications Display Not available ProLink II ProLink > Configuration > Flow > Vol Flow Type ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > GSV > Volume Flow Type > Standard Gas Volume Overvie[...]

Procedure Set Standard Gas Density to the standard reference density of the gas you are measuring. Note ProLink II and ProLink III provide a guided method that you can use to calculate the standard density of your gas, if you do not know it. 4.3.3 Configure Gas Standard Volume Flow Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UN[...]

Options for Gas Standard Volume Measurement Unit Table 4-4: Unit description Label Display ProLink II ProLink III Field Communica- tor Normal cubic meters per sec- ond NM3/S Nm3/sec Nm3/sec Nm3/sec Normal cubic meters per mi- nute NM3/MN Nm3/min Nm3/sec Nm3/min Normal cubic meters per hour NM3/H Nm3/hr Nm3/hr Nm3/hr Normal cubic meters per day NM3/[...]

Overview A special measurement unit is a user-defined unit of measure that allows you to report process data, totalizer data, and inventory data in a unit that is not available in the transmitter. A special measurement unit is calculated from an existing measurement unit using a conversion factor. Note Although you cannot define a special measureme[...]

4.3.4 Configure Gas Standard Volume Flow Cutoff Display Not available ProLink II ProLink > Configuration > Flow > Std Gas Vol Flow Cutoff ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > GSV > GSV Cutoff Overview Gas Standard Volume Flow [...]

Example: Cutoff interaction with AO Cutoff higher than Gas Standard Volume Flow Cutoff Configuration: • mA Output Process Variable for the primary mA output: Gas Standard Volume Flow Rate • Frequency Output Process Variable : Gas Standard Volume Flow Rate • AO Cutoff for the primary mA output: 15 SLPM (standard liters per minute) • Gas Stan[...]

4.4.1 Options for Flow Direction Options for Flow Direction Table 4-5: Flow Direction setting Relationship to Flow Direction ar- row on sensor ProLink II ProLink III Field Communicator Forward Forward Forward Appropriate when the Flow Direction arrow is in the same direction as the majority of flow. Reverse Reverse Reverse Appropriate when the Flow[...]

Effect of Flow Direction on the mA output: Lower Range Value = 0 Figure 4-1: Flow Direction = Forward mA output -x 0 x Reverse flow Forward flow 20 12 4 Flow Direction = Reverse, Negate Forward mA output -x 0 x Reverse flow Forward flow 20 12 4 Flow Direction = Absolute V alue, Bidirectional, Negate Bidirectional mA output -x 0 x Reverse flow Forwa[...]

• Under conditions of reverse flow or zero flow, the mA output is 4 mA. • Under conditions of forward flow, up to a flow rate of 100 g/sec, the mA output varies between 4 mA and 20 mA in proportion to the flow rate. • Under conditions of forward flow, if the flow rate equals or exceeds 100 g/sec, the mA output will be proportional to the flow[...]

Effect of Flow Direction on frequency outputs Flow Direction affects how the transmitter reports flow values via the frequency outputs. The frequency outputs are affected by Flow Direction only if Frequency Output Process Variable is set to a flow variable. Effect of the Flow Direction parameter and actual flow direction on frequency outputs Table [...]

Effect of the Flow Direction parameter and actual flow direction on flow values reported via digital communications Table 4-8: Flow Direction setting Actual flow direction Forward Zero flow Reverse Forward Positive 0 Negative Reverse Positive 0 Negative Bidirectional Positive 0 Negative Absolute Value Positive (3) 0 Positive Negate Forward Negative[...]

4.5.1 Configure Density Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > DENS ProLink II ProLink > Configuration > Density > Density Units ProLink III Device Tools > Configuration > Process Measurement > Density Field Communicator Configure > Manual Setup > Measurements > Density > Density Un[...]

4.5.2 Configure slug flow parameters Display Not available ProLink II • ProLink > Configuration > Density > Slug High Limit • ProLink > Configuration > Density > Slug Low Limit • ProLink > Configuration > Density > Slug Duration ProLink III Device Tools > Configuration > Process Measurement > Density Field [...]

The default value for Slug High Limit is 5.0 g/cm 3 . The range is 0.0 to 10.0 g/cm 3 . 3. Set Slug Duration to the number of seconds that the transmitter will wait for a slug flow condition to clear before performing the configured slug flow action. The default value for Slug Duration is 0.0 seconds. The range is 0.0 to 60.0 seconds. Slug flow det[...]

Overview Damping is used to smooth out small, rapid fluctuations in process measurement. Damping Value specifies the time period (in seconds) over which the transmitter will spread changes in the reported process variable. At the end of the interval, the reported process variable will reflect 63% of the change in the actual measured value. Procedur[...]

Interaction between Density Damping and Added Damping In some circumstances, both Density Damping and Added Damping are applied to the reported density value. Density Damping controls the rate of change in the density process variable. Added Damping controls the rate of change reported via the mA output. If mA Output Process Variable is set to Dens[...]

4.6.1 Configure Temperature Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > TEMP ProLink II ProLink > Configuration > Temperature > Temp Units ProLink III Device Tools > Configuration > Process Measurement > Temperature Field Communicator Configure > Manual Setup > Measurements > Temperature &g[...]

Overview Damping is used to smooth out small, rapid fluctuations in process measurement. Damping Value specifies the time period (in seconds) over which the transmitter will spread changes in the reported process variable. At the end of the interval, the reported process variable will reflect 63% of the change in the actual measured value. Procedur[...]

4.7 Configure the petroleum measurement application The petroleum measurement application enables Correction for the effect of Temperature on the volume of Liquids (CTL), by calculating and applying a Volume Correction Factor (VCF) to volume measurement. Internal calculations are performed in compliance with American Petroleum Institute (API) stand[...]

Option Setup Polling for tempera- ture a. Ensure that the primary mA output has been wired to support HART polling. b. Choose View > Preferences . c. Enable Use External Temperature . d. Choose ProLink > Configuration > Polled Variables . e. Choose an unused polling slot. f. Set Polling Control to Poll As Primary or Poll as Secondary , and[...]

5. Set Temperature Source to the method that the transmitter will use to obtain temperature data. Option Description Poll for external value The transmitter will poll an external temperature device, us- ing HART protocol over the primary mA output. RTD The transmitter will use the temperature data from the sen- sor. Static or Digital Communications[...]

4.7.3 Configure petroleum measurement using the Field Communicator 1. Choose Online > Configure > Manual Setup > Measurements > Set Up Petroleum . 2. Specify the API table to use. a. Open the Petroleum Measurement Source menu and select the API table number. Depending on your choice, you may be prompted to enter a reference temperature [...]

Option Setup A value written by digital communica- tions a. Choose Online > Configure > Manual Setup > Measurements > External Pressure/Temperature > Temperature . b. Set External Temperature to Enabled . c. Perform the necessary host programming and communications setup to write temperature data to the transmitter at appropri- ate i[...]

API reference tables, associated process fluids, and associated calculation values (continued) Table 4-13: Table name Process fluid CTL source data Reference temperature Density unit 53B Generalized products Observed density and observed temperature 15 °C (configurable) Base density Range: 653 to 1075 kg/m 3 53D Lubricating oils Observed density a[...]

• The concentration measurement application must be enabled on your transmitter. • The concentration matrix you want to use must be available on your transmitter, or it must be available as a file on your computer. • You must know the derived variable that your matrix is designed for. • You must know the density unit used by your matrix. ?[...]

Restriction The high and low limit alarms require the enhanced core processor. Example: If Alarm Limit is set to 5%, Enable Temp High is checked, and the matrix is built for a temperature range of 40 °F to 80 °F, an extrapolation alarm will be posted if process temperature goes above 82 °F 7. Select the label that will be used for the concentrat[...]

Option Setup A value written by digital communica- tions a. Choose View > Preferences . b. Enable Use External Temperature . c. Perform the necessary host programming and communications setup to write temperature data to the transmitter at appropri- ate intervals. Note If the Weights & Measures application is implemented and the trans- mitte[...]

3. Choose Device Tools > Configuration > Process Measurement > Concentration Measurement . 4. Set Derived Variable to the derived variable that your matrix is designed for, and click Apply . Important • All concentration matrices on your transmitter must use the same derived variable. If you are using one of the standard matrices from Mi[...]

Restriction The high and low limit alarms require the enhanced core processor. Example: If Extrapolation Alarm Limit is set to 5%, High Extrapolation Limit (Temperature) is enabled, and the matrix is built for a temperature range of 40 °F to 80 °F, an extrapolation alarm will be posted if process temperature goes above 82 °F 8. Set Temperature S[...]

13. Set Active Matrix to the matrix to be used for measurement. Concentration process variables are now available on the transmitter. You can view and report them in the same way that you view and report other process variables. 4.8.3 Configure concentration measurement using the Field Communicator This task guides you through setting up a concentr[...]

d. Choose Online > Configure > Alert Setup > CM Alerts . e. Enable or disable the high and low limit alarms for temperature and density, as desired. Restriction The high and low limit alarms require the enhanced core processor. Example: If Alarm Limit is set to 5%, the high-temperature extrapolation alert is enabled, and the matrix is buil[...]

Option Setup Polling for tempera- ture a. Ensure that the primary mA output has been wired to support HART polling. b. Choose Online > Configure > Manual Setup > Measurements > External Pressure/Temperature > Temperature . c. Enable External Temperature . d. Choose Online > Configure > Manual Setup > Measurements > Extern[...]

Tip If the standard matrices are not appropriate for your application, you can build a custom matrix or purchase a custom matrix from Micro Motion. Standard concentration matrices and associated measurement units Table 4-14: Matrix name Description Density unit Temperature unit Concentration unit Deg Balling Matrix represents percent extract, by ma[...]

Derived variables and calculated process variables Table 4-15: Derived Variable Description Calculated process variables Density at reference tempera- ture Standard volume flow rate Specific gravity Concen- tration Net mass flow rate Net vol- ume flow rate Density at reference temperature Mass/unit volume, cor- rected to a given refer- ence tempera[...]

Derived variables and calculated process variables (continued) Table 4-15: Derived Variable Description Calculated process variables Density at reference tempera- ture Standard volume flow rate Specific gravity Concen- tration Net mass flow rate Net vol- ume flow rate Concentration de- rived from specific gravity The mass, volume, weight, or number[...]

The flow factor is the percent change in the flow rate per PSI. When entering the value, reverse the sign. Example: If the flow factor is 0.000004 % per PSI, enter − 0.000004 % per PSI. 4. Enter Density Factor for your sensor. The density factor is the change in fluid density, in g/cm 3 /PSI. When entering the value, reverse the sign. Example: If[...]

Option Setup A value written by digital communica- tions a. Set Pressure Units to the desired unit. b. Perform the necessary host programming and communications setup to write pressure data to the transmitter at appropriate in- tervals. Note If the Weights & Measures application is implemented and the trans- mitter is secured, digital communica[...]

The density factor is the change in fluid density, in g/cm 3 /PSI. When entering the value, reverse the sign. Example: If the density factor is 0.000006 g/cm 3 /PSI, enter − 0.000006 g/cm3/PSI. 6. Set Pressure Source to the method that the transmitter will use to obtain pressure data. Option Description Poll for external value The transmitter wil[...]

9. If you want to use digital communications, click Apply , then perform the necessary host programming and communications setup to write temperature data to the transmitter at appropriate intervals. Postrequisites If you are using an external pressure value, verify the setup by checking the External Pressure value displayed in the Inputs area of t[...]

Option Setup A user-configured static pressure val- ue a. Set Pressure Unit to the desired unit. b. Set Compensation Pressure to the desired value. Polling for pressure a. Ensure that the primary mA output has been wired to support HART polling. b. Choose Online > Configure > Manual Setup > Measurements > External Pressure/Temperature &[...]

Options for Pressure Measurement Unit Table 4-16: Unit description Label Display ProLink II ProLink III Field Communica- tor Feet water @ 68 °F FTH2O Ft Water @ 68°F Ft Water @ 68°F ftH2O Inches water @ 4 °C INW4C In Water @ 4°C In Water @ 4°C inH2O @4DegC Inches water @ 60 °F INW60 In Water @ 60°F In Water @ 60°F inH2O @60DegF Inches wate[...]

Configure process measurement 76 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

5 Configure device options and preferences Topics covered in this chapter: • Configure the transmitter display • Enable or disable operator actions from the display • Configure security for the display menus • Configure response time parameters • Configure alarm handling • Configure informational parameters 5.1 Configure the transmitter[...]

The languages available depend on your transmitter model and version. 5.1.2 Configure the process variables shown on the display Display Not available ProLink II ProLink > Configuration > Display ProLink III Device Tools > Configuration > Transmitter Display > Display Variables Field Communicator Configure > Manual Setup > Disp[...]

Display variable Process variable assignment Display Variable 10 None Display Variable 11 None Display Variable 12 None Display Variable 13 None Display Variable 14 None Display Variable 15 None Configure Display Variable 1 to track the primary mA output Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLY > VAR 1 ProLink II ProLink > Confi[...]

Overview Setting Display Precision determines the precision (number of decimal places) shown on the display. You can set Display Precision independently for each variable. Setting Display Precision does not affect the actual value of the process variable. Procedure 1. Select a process variable. 2. Set Display Precision to the number of decimal plac[...]

5.1.5 Enable or disable automatic scrolling through the display variables Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > AUTO SCRLL ProLink II ProLink > Configuration > Display > Display Options > Display Auto Scroll ProLink III Device Tools > Configuration > Transmitter Display > General Field Communicator Config[...]

Procedure Enable or disable Backlight . The default setting is Enabled . 5.1.7 Enable or disable Status LED Blinking Display Not available ProLink II ProLink > Configuration > Display > Display Options > Display Status LED Blinking ProLink III Device Tools > Configuration > Transmitter Display > General Field Communicator Confi[...]

5.2.1 Enable or disable Totalizer Start/Stop from the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > TOTALS STOP ProLink II ProLink > Configuration > Display > Display Options > Display Start/Stop Totalizers ProLink III Device Tools > Configuration > Totalizer Control Methods Field Communicator Configure >[...]

Restrictions • This parameter does not apply to inventories. You cannot reset inventories from the display. • You cannot use the display to reset all totalizers as a group. You must reset totalizers individually. • If the petroleum measurement application is installed on your computer, the operator must enter the off-line password to perform [...]

Option Description Enabled (default) Operators can use a single display command to acknowledge all alarms at once. Disabled Operators cannot acknowledge all alarms at once, they must be ac- knowledged individually. 5.3 Configure security for the display menus Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY ProLink II ProLink > Configurat[...]

3. To require a password for access to the maintenance section of the off-line menu and the Smart Meter Verification menu, enable or disable Off-Line Password . Option Description Enabled Operator is prompted for the off-line password at entry to the Smart Meter Verification menu (if applicable) or entry to the maintenance section of the off-line m[...]

5.4.1 Configure Update Rate Display Not available ProLink II ProLink > Configuration > Device > Update Rate ProLink III Device Tools > Configuration > Process Measurement > Response > Update Rate Field Communicator Configure > Manual Setup > Measurements > Update Rate Overview Update Rate controls the rate at which pro[...]

Effects of Update Rate = Special Incompatible features and functions Special mode is not compatible with the following features and functions: • Enhanced events. Use basic events instead. • All calibration procedures. • Zero verification. • Restoring the factory zero or the prior zero. If required, you can switch to Normal mode, perform the[...]

5.4.2 Configure Calculation Speed (Response Time) Display Not available ProLink II ProLink > Configuration > Device > Response Time ProLink III Device Tools > Configuration > Process Measurement > Response > Calculation Speed Field Communicator Not available Overview Calculation Speed is used to apply a different algorithm to t[...]

5.5.1 Configure Fault Timeout Display Not available ProLink II ProLink > Configuration > Analog Output > Last Measured Value Timeout ProLink > Configuration > Frequency/Discrete Output > Frequency > Last Measured Value Timeout ProLink III Device Tools > Configuration > Fault Processing Field Communicator Configure > Al[...]

Overview Use Status Alarm Severity to control the fault actions that the transmitter performs when it detects an alarm condition. Restrictions • For some alarms, Status Alarm Severity is not configurable. • For some alarms, Status Alarm Severity can be set only to two of the three options. Tip Micro Motion recommends using the default settings [...]

Status alarms and Status Alarm Severity Table 5-2: Alarm code Status message Default severity Notes Configurable? A001 EEPROM Error (Core Pro- cessor) Fault No A002 RAM Error (Core Processor) Fault No A003 No Sensor Response Fault Yes A004 Temperature Overrange Fault No A005 Mass Flow Rate Overrange Fault Yes A006 Characterization Required Fault Ye[...]

Status alarms and Status Alarm Severity (continued) Table 5-2: Alarm code Status message Default severity Notes Configurable? A031 Low Power Fault Applies only to flowmeters with the enhanced core processor. No A032 Meter Verification in Pro- gress: Outputs to Fault Varies Applies only to transmitters with Smart Meter Verification. If outputs are s[...]

Status alarms and Status Alarm Severity (continued) Table 5-2: Alarm code Status message Default severity Notes Configurable? A114 mA Output 2 Fixed Informational Can be set to either Informational or Ignore , but cannot be set to Fault . Yes A115 No External Input or Polled Data Informational Yes A116 Temperature Overrange (Petroleum) Informationa[...]

- Message - Date • Sensor parameters - Sensor Serial Number - Sensor Material - Sensor Liner Material - Sensor Flange Type 5.6.1 Configure Descriptor Display Not available ProLink II ProLink > Configuration > Device > Descriptor ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator [...]

5.6.3 Configure Date Display Not available ProLink II ProLink > Configuration > Device > Date ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator Configure > Manual Setup > Info Parameters > Transmitter Info > Date Overview Date lets you store a static date (not updated [...]

5.6.5 Configure Sensor Material Display Not available ProLink II ProLink > Configuration > Sensor > Sensor Matl ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Tube Wetted Material Overview Sensor Material [...]

5.6.7 Configure Sensor Flange Type Display Not available ProLink II ProLink > Configuration > Sensor > Flange ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Sensor Flange Overview Sensor Flange Type lets y[...]

6 Integrate the meter with the control system Topics covered in this chapter: • Configure the transmitter channels • Configure the mA output • Configure the frequency output • Configure the discrete output • Configure events • Configure digital communications 6.1 Configure the transmitter channels Display OFF-LINE MAINT > OFF-LINE CO[...]

Postrequisites For each channel that you configured, perform or verify the corresponding input or output configuration. When the configuration of a channel is changed, the channel’s behavior will be controlled by the configuration that is stored for the selected input or output type, and the stored configuration may not be appropriate for your pr[...]

• If you plan to configure an output to report a concentration measurement process variable, ensure that the concentration measurement application is configured so that the desired variable is available. • If you are using the HART variables, be aware that changing the configuration of mA Output Process Variable will change the configuration of[...]

Options for mA Output Process Variable (continued) Table 6-1: Process variable Label Display ProLink II ProLink III Field Communicator Concentration measurement Density at reference RDENS CM: Density @ Reference Density at Reference Temperature ED Dens at Ref Specific gravity SGU CM: Density (Fixed SG units) Density (Fixed SG Units) ED Dens (SGU) S[...]

Procedure Set LRV and URV as desired. • LRV is the value of mA Output Process Variable represented by an output of 4 mA. The default value for LRV depends on the setting of mA Output Process Variable . Enter LRV in the measurement units that are configured for mA Output Process Variable . • URV is the value of mA Output Process Variable represe[...]

Default values for Lower Range Value (LRV) and Upper Range Value (URV) (continued) Table 6-2: Process variable LRV URV Concentration 0% 100% Baume 0 10 Specific gravity 0 10 6.2.3 Configure AO Cutoff Display Not available ProLink II ProLink > Configuration > Analog Output > Primary Output > AO Cutoff ProLink III Device Tools > Config[...]

Example: Cutoff interaction Configuration: • mA Output Process Variable = Mass Flow Rate • Frequency Output Process Variable = Mass Flow Rate • AO Cutoff = 10 g/sec • Mass Flow Cutoff = 15 g/sec Result: If the mass flow rate drops below 15 g/sec, all outputs representing mass flow will report zero flow. Example: Cutoff interaction Configura[...]

Note Added Damping is not applied if the mA output is fixed (for example, during loop testing) or if the mA output is reporting a fault. Added Damping is applied while sensor simulation is active. Procedure Set Added Damping to the desired value. The default value is 0.0 seconds. When you specify a value for Added Damping , the transmitter automati[...]

Result: A change in the mass flow rate will be reflected in the mA output over a time period that is greater than 3 seconds. The exact time period is calculated by the transmitter according to internal algorithms which are not configurable. 6.2.5 Configure mA Output Fault Action and mA Output Fault Level Display Not available ProLink II • ProLink[...]

Options for mA Output Fault Action and mA Output Fault Level (continued) Table 6-4: Option mA output behavior mA Output Fault Level None Tracks data for the assigned process vari- able; no fault action Not applicable CAUTION! If you set mA Output Fault Action or Frequency Output Fault Action to None , be sure to set Digital Communications Fault Act[...]

Overview Frequency Output Process Variable controls the variable that is reported over the frequency output. Prerequisites If you plan to configure the output to report volume flow, ensure that you have set Volume Flow Type as desired: Liquid or Gas Standard Volume . If you plan to configure an output to report a concentration measurement process v[...]

Options for Frequency Output Process Variable (continued) Table 6-5: Process variable Label Display ProLink II ProLink III Field Communica- tor Net mass flow NET M ED: Net Mass Flow Rate Net Mass Flow Rate ED Net Mass flo Net volume flow NET V ED: Net Vol Flow Rate Net Volume Flow Rate ED Net Vol flo 6.3.2 Configure Frequency Output Polarity Displa[...]

6.3.3 Configure Frequency Output Scaling Method Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET FO > FO SCALE ProLink II ProLink > Configuration > Frequency/Discrete Output > Frequency > Scaling Method ProLink III Device Tools > Configuration > I/O > Outputs > Frequency Output Field Communicator Conf[...]

N Number of pulses per flow unit, as configured in the receiving device The resulting Frequency Factor must be within the range of the frequency output (0 to 10,000 Hz): • If Frequency Factor is less than1 Hz,reconfigure the receiving device for a higher pulses/unit setting. • If Frequency Factor is greater than 10,000 Hz, reconfigure the recei[...]

The ON signal may be the high voltage or 0.0 V , depending on Frequency Output Polarity . Interaction of Frequency Output Maximum Pulse Width and Frequency Output Polarity Table 6-7: Polarity Pulse width Active High Active Low Procedure Set Frequency Output Maximum Pulse Width as desired. The default value is 277 milliseconds. You can set Frequency[...]

Note For some faults only: If Last Measured Value Timeout is set to a non-zero value, the transmitter will not implement the fault action until the timeout has elapsed. Procedure 1. Set Frequency Output Fault Action as desired. The default value is Downscale (0 Hz). 2. If you set Frequency Output Fault Action to Upscale , set Frequency Fault Level [...]

• Discrete Output Polarity • Discrete Output Fault Action Restriction Before you can configure the discrete output, you must configure a channel to operate as a discrete output. Important Whenever you change a discrete output parameter, verify all other discrete output parameters before returning the flowmeter to service. In some situations, th[...]

Options for Discrete Output Source (continued) Table 6-9: Option Label Condition Discrete out- put voltage Display ProLink II ProLink III Field Commu- nicator Enhanced Event 4 Enhanced Event 5 OFF 0 V Event 1–2 (2) EVNT1 EVNT2 E1OR2 Event 1 Event 2 Event 1 or Event 2 Event 1 Event 2 Event 1 or Event 2 Status Event 1 Event 2 Event 1 or Event 2 ON [...]

Configure Flow Switch parameters Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > CONFIG FL SW ProLink II • ProLink > Configuration > Flow > Flow Switch Variable • ProLink > Configuration > Flow > Flow Switch Setpoint • ProLink > Configuration > Flow > Flow Switch Hysteresis ProLink III [...]

6.4.2 Configure Discrete Output Polarity Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > DO POLAR ProLink II ProLink > Configuration > Frequency/Discrete Output > Discrete Output > DO Polarity ProLink III Device Tools > Configuration > I/O > Outputs > Discrete Output Field Communicator Configure[...]

Typical discrete output circuit Figure 6-1: A. 24 V (Nom) B. 3.2 K Ω C. Out+ D. Out − 6.4.3 Configure Discrete Output Fault Action Display Not available ProLink II ProLink > Configuration > Frequency/Discrete Output > Discrete Output > DO Fault Action ProLink III Device Tools > Configuration > Fault Processing Field Communicat[...]

Procedure Set Discrete Output Fault Action as desired. The default setting is None . Options for Discrete Output Fault Action Options for Discrete Output Fault Action Table 6-11: Label Discrete output behavior Polarity= Active High Polarity= Active Low Upscale • Fault: discrete output is ON (site-specific voltage) • No fault: discrete output is[...]

6.5.1 Configure a basic event Display Not available ProLink II ProLink > Configuration > Events ProLink III Device Tools > Configuration > Events > Basic Events Field Communicator Not available Overview A basic event is used to provide notification of process changes. A basic event occurs (is ON) if the real-time value of a user-spec[...]

Overview An enhanced event is used to provide notification of process changes and, optionally, to perform specific transmitter actions if the event occurs. An enhanced event occurs (is ON) if the real-time value of a user-specified process variable moves above (HI) or below (LO) a user-defined setpoint, or in range (IN) or out of range (OUT) with r[...]

Options for Enhanced Event Action Options for Enhanced Event Action Table 6-12: Action Label Display ProLink II ProLink III Field Communicator Standard None (default) NONE None None None Start sensor zero START ZERO Start Sensor Zero Start Sensor Zero Perform auto zero Start/stop all totaliz- ers START STOP Start/Stop All Totalization Start/Stop Al[...]

6.6 Configure digital communications The digital communications parameters control how the transmitter will communicate using digital communications. Your transmitter supports the following types of digital communications: • HART/Bell 202 over the primary mA terminals • HART/RS-485 over the RS-485 terminals • Modbus/RS-485 over the RS-485 ter[...]

2. Ensure Loop Current Mode ( mA Output Action ) is configured appropriately. Options Description Enabled The primary mA output reports process data as configured. Disabled The primary mA output is fixed at 4 mA and does not report process data. Important If you use ProLink II or ProLink III to set HART Address to 0 , the program automatically enab[...]

Label Description ProLink II ProLink III Field Communi- cator Primary Variable Source (Primary Variable) PV The transmitter sends the primary variable (PV) in the configured measurement units in each burst (e.g., 14.0 g/sec, 13.5 g/sec, 12.0 g/sec). PV current & % of range Primary Variable (Percent Range/ Current) % range/current The transmitte[...]

Options for HART variables Options for HART variables Table 6-13: Process variable Primary Varia- ble (PV) Secondary Variable (SV) Third Variable (TV) Fourth Varia- ble (QV ) Standard Mass flow rate ✓ ✓ ✓ ✓ Line (Gross) Volume flow rate ✓ ✓ ✓ ✓ Temperature ✓ ✓ ✓ Density ✓ ✓ ✓ Drive gain ✓ ✓ ✓ Mass total ✓ Line (G[...]

Options for HART variables (continued) Table 6-13: Process variable Primary Varia- ble (PV) Secondary Variable (SV) Third Variable (TV) Fourth Varia- ble (QV ) ED standard volume flow rate ✓ ✓ ✓ ✓ ED standard volume total ✓ ED standard volume inventory ✓ ED net mass flow rate ✓ ✓ ✓ ✓ ED net mass total ✓ ED net mass inventory ?[...]

6.6.2 Configure HART/RS-485 communications Display OFF-LINE MAINT > OFF-LINE CONFG > COMM ProLink II ProLink > Configuration > Device > Digital Comm Settings > HART Address ProLink > Configuration > RS-485 ProLink III Device Tools > Configuration > Communications > Communications (HART) Field Communicator Configure [...]

6.6.3 Configure Modbus/RS-485 communications Display OFF-LINE MAINT > OFF-LINE CONFG > COMM ProLink II ProLink > Configuration > Device > Digital Comm Settings ProLink III Device Tools > Configuration > Communications > RS-485 Terminals Field Communicator Configure > Manual Setup > Inputs/Outputs > Communications &g[...]

4. Set Parity , Stop Bits , and Baud Rate as appropriate for your network. 5. Set Floating-Point Byte Order to match the byte order used by your Modbus host. Code Byte order 0 1–2 3–4 1 3–4 1–2 2 2–1 4–3 3 4–3 2–1 See Table 6-15 for the bit structure of bytes 1, 2, 3, and 4. Bit structure of floating-point bytes Table 6-15: Byte Bit[...]

Overview Digital Communications Fault Action specifies the values that will be reported via digital communications if the transmitter encounters an internal fault condition. Procedure Set Digital Communications Fault Action as desired. The default setting is None . Options for Digital Communications Fault Action Options for Digital Communications F[...]

CAUTION! If you set mA Output Fault Action or Frequency Output Fault Action to None , be sure to set Digital Communications Fault Action to None . If you do not, the output will not report actual process data, and this may result in measurement errors or unintended consequences for your process. Restriction If you set Digital Communications Fault A[...]

Integrate the meter with the control system 134 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

7 Completing the configuration Topics covered in this chapter: • Test or tune the system using sensor simulation • Back up transmitter configuration • Enable write-protection on the transmitter configuration 7.1 Test or tune the system using sensor simulation Use sensor simulation to test the system's response to a variety of process con[...]

Option Required values Sine Period Minimum Maximum 4. For density, set Wave Form as desired and enter the required values. Option Required values Fixed Fixed Value Sawtooth Period Minimum Maximum Sine Period Minimum Maximum 5. For temperature, set Wave Form as desired and enter the required values. Option Required values Fixed Fixed Value Sawtooth [...]

• All mass flow rate, temperature, and density values shown on the display or reported via outputs or digital communications • The mass total and mass inventory values • All volume calculations and data, including reported values, volume totals, and volume inventories • All mass, temperature, density, or volume values logged to Data Logger [...]

7.3 Enable write-protection on the transmitter configuration Display OFF-LINE MAINT > CONFIG > LOCK ProLink II ProLink > Configuration > Device > Enable Write Protection ProLink III Device Tools > Configuration > Write-Protection Field Communicator Configure > Manual Setup > Info Parameters > Transmitter Info > Writ[...]

8 Set up the Weights & Measures application Topics covered in this chapter: • Weights & Measures application • Set up the Weights & Measures application using ProLink II • Set up the Weights & Measures application using ProLink III Information in this chapter is applicable only if your transmitter was ordered with the Weights [...]

Metrological security Metrological security protects the transmitter from all changes that would affect measurement. This includes changes to configuration and some maintenance procedures. Micro Motion implements metrological security via “software security.” Software security is a setting inside the transmitter that programmatically disables t[...]

3. Set Approval to the appropriate regulatory agency for your application. Option Description NTEP Regulatory agency for the U.S.A. and Canada OIML Regulatory agency for all other world areas 4. Set Totalizer Reset Options as desired. Option Description Not Resettable from Display and Digital Comm When the transmitter is secured, totalizers cannot [...]

FVZ is a diagnostic variable that monitors the zero value over a period of 3 minutes. It must be read during meter commissioning to comply with MID requirements for Weights & Measures applications in Measuring Instrument Directive (MID) 2004/22/ EC. Refer to your Standard Operating Procedures documentation for detailed instructions. 9. Enable s[...]

8.3 Set up the Weights & Measures application using ProLink III When your transmitter is set up to comply with OIML or NTEP requirements, and the transmitter is “secured,” selected measurement data from the transmitter is approved for Weights & Measures applications. Prerequisites Important Review the Weights & Measures requirements[...]

“Digital communications” refers to any method that uses Modbus or HART communications to interact with the transmitter. This includes ProLink II, ProLink III, the Field Communicator, and any host. 4. If required for your installation, configure your transmitters for two frequency outputs and set them to operate in Quadrature mode. a. Choose Dev[...]

9. Install the physical seal. Important In most installations, the physical seal is a wire seal that must be installed by a certified Weights & Measures inspector. The seal is provided by the inspector. The physical seal is inserted through the locking clamps on the transmitter (if available on your transmitter). Example of locking clamp and se[...]

Set up the Weights & Measures application 146 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Part III Operations, maintenance, and troubleshooting Chapters covered in this part: • Transmitter operation • Operate the transmitter with the Weights & Measures application • Measurement support • Troubleshooting Operations, maintenance, and troubleshooting Configuration and Use Manual 147[...]

Operations, maintenance, and troubleshooting 148 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

9 Transmitter operation Topics covered in this chapter: • Record the process variables • View process variables • View transmitter status using the status LED • View and acknowledge status alarms • Read totalizer and inventory values • Start and stop totalizers and inventories • Reset totalizers • Reset inventories 9.1 Record the pr[...]

9.2 View process variables Display Scroll to the desired process variable. If AutoScroll is enabled, you can wait until the proc- ess variable is displayed. See Section 9.2.1 for more information. ProLink II ProLink > Process Variables ProLink > API process variables (petroleum measurement application) ProLink > CM process variables (conce[...]

Transmitter display features Figure 9-1: A B C D E F G H A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator: turns red when either Scroll or Select is activated F. Select optical switch G. Unit of measure for process variable H. Current value of process variable 9.2.2 View process variables[...]

9.3 View transmitter status using the status LED The status LED shows the current alarm condition of the transmitter. The status LED is located on the face of the transmitter. Observe the status LED. • If your transmitter has a display, you can view the status LED with the transmitter housing cover in place. • If your transmitter does not have [...]

Prerequisites Operator access to the alarm menu must be enabled (default setting). If operator access to the alarm menu is disabled, you must use another method to view or acknowledge status alarms. Procedure See Figure 9-2 . Transmitter operation Configuration and Use Manual 153[...]

Using the display to view and acknowledge the status alarms Figure 9-2: SEE ALARM Y es Scroll and Select simultaneously for 4 seconds ACK ALL Y es EXIT Select No Alarm code Scroll ACK Y es Select No Active/ unacknowledged alarms? No Y es Select NO ALARM EXIT Scroll Scroll Select Scroll Scroll Select Is ACK ALL enabled? Y es No Transmitter operation[...]

Postrequisites • To clear the following alarms, you must correct the problem, acknowledge the alarm, then power-cycle the transmitter: A001, A002, A010, A011, A012, A013, A018, A019, A022, A023, A024, A025, A028, A029, A031. • For all other alarms: - If the alarm is inactive when it is acknowledged, it will be removed from the list. - If the al[...]

9.4.3 View and acknowledge alerts using ProLink III You can view a list containing all alerts that are active, or inactive and have been unacknowleged. From this list, you can acknowlege individual alerts or choose to acknowledge all alerts at once. 1. View alerts on the ProLink III main screen under Alerts . All active or unacknowledged alarms are[...]

• To refresh the list of active or unacknowledged alarms, press Service Tools > Alerts > Refresh Alerts . 9.4.5 Alarm data in transmitter memory The transmitter maintains three sets of data for every alarm that is posted. For each alarm occurrence, the following three sets of data are maintained in transmitter memory: • Alert List • Ale[...]

Overview Totalizers keep track of the total amount of mass or volume measured by the transmitter since the last totalizer reset. Inventories keep track of the total amount of mass or volume measured by the transmitter since the last inventory reset. Tip You can use the inventories to keep a running total of mass or volume across multiple totalizer [...]

1. Scroll until the word TOTAL appears in the lower left corner of the display. Important Because all totalizers are started or stopped together, it does not matter which total you use. 2. Select . 3. Scroll until START appears beneath the current totalizer value. 4. Select . 5. Select again to confirm. 6. Scroll to EXIT . • To stop all totalizer[...]

9.7 Reset totalizers Display See Section 9.7.1 . ProLink II ProLink > Totalizer Control > Reset Mass Total ProLink > Totalizer Control > Reset Volume Total ProLink > Totalizer Control > Reset Gas Volume Total ProLink > Totalizer Control > Reset ProLink III Device Tools > Totalizer Control > Totalizer and Inventories &g[...]

3. Scroll until RESET appears beneath the current totalizer value. 4. Select . 5. Select again to confirm. 6. Scroll to EXIT . 7. Select . • To reset the volume totalizer: 1. Scroll until the volume totalizer value appears. 2. Select . 3. Scroll until RESET appears beneath the current totalizer value. 4. Select . 5. Select again to confirm. 6. Sc[...]

Overview When you reset an inventory, the transmitter sets its value to 0. It does not matter whether the inventory is started or stopped. If the inventory is started, it continues to track process measurement. Tip When you reset a single inventory, the values of other inventories are not reset. Totalizer values are not reset. Prerequisites To use [...]

10 Operate the transmitter with the Weights & Measures application Topics covered in this chapter: • Operate the transmitter when the Weights & Measures application is installed • Switch between secured and unsecured mode • Clear Status Alarm A027: Security Breach • Replacing the core processor in a Weights & Measures installati[...]

• You cannot stop totalizers while the tranmitter is secured. • You cannot reset inventories while the transmitter is secured. 10.1.1 Approved methods to read or obtain process data When the Weights & Measures application is installed, process data is approved for custody transfer use only if an approved method is used for reading or obtain[...]

The display is able to show a maximum of eight characters, including the decimal point. For all totalizer values configured as display variables, the position of the decimal point on the display is fixed to the configured precision of the display variable. When the totalizer reaches the largest value that can be displayed in these circumstances: ?[...]

Transmitter outputs and process data when Approvals= OIML Table 10-4: Function Transmitter status Unsecured Secured Outputs mA output behavior Performs configured fault action Normal Frequency output behavior Performs configured fault action Normal Discrete output behavior Performs configured fault action Normal Process variables All flow rates Rep[...]

Available actions when Approvals= NTEP (continued) Table 10-5: Function Transmitter status Unsecured Secured Outputs set to Last Meas- ured Value Allowed Not allowed External pressure and tem- perature data Retrieved by polling Allowed Allowed Written by Modbus or HART host Allowed Not allowed Testing and trimming out- puts mA output loop test Allo[...]

Available actions when Approvals= OIML (continued) Table 10-6: Function Transmitter status Unsecured Secured Smart Meter Verification Outputs set to Continue Measuring Allowed Allowed Outputs set to Fault Allowed Allowed Outputs set to Last Meas- ured Value Allowed Not allowed External pressure and temperature data Retrieved by polling Allowed Allo[...]

The controls are not accessible in any other way. 10.2.1 Switch between secured and unsecured mode using ProLink II Prerequisites Before switching to unsecured mode, ensure that you will be able to switch back to secured mode. Because switching to unsecured mode requires breaking the physical seal, switching back to secured mode may require a site [...]

1. Make a service port connection to your transmitter. 2. Choose Device Tools > Configuration > Weights & Measures . 3. Set Software Security to Enabled . 10.2.3 Switch between secured and unsecured mode using the switching utility Prerequisites The switching utility must be installed on your PC. The switching utility is available from th[...]

10.4 Replacing the core processor in a Weights & Measures installation In a Weights & Measures installation, replacing the core processor requires re-sealing the transmitter. When the transmitter is first secured, the core processor’s unique ID is registered with the transmitter. If you replace the core processor with another core process[...]

Operate the transmitter with the Weights & Measures application 172 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

11 Measurement support Topics covered in this chapter: • Options for measurement support • Use Smart Meter Verification • Zero the flowmeter • Validate the meter • Perform a (standard) D1 and D2 density calibration • Perform a D3 and D4 density calibration (T-Series sensors only) • Perform temperature calibration 11.1 Options for meas[...]

11.2.1 Smart Meter Verification requirements To use Smart Meter Verification, the transmitter must be paired with an enhanced core processor, and the Smart Meter Verification option must be ordered for the transmitter. See Table 11-1 for the minimum version of the transmitter, enhanced core processor, and communication tool needed to support Smart [...]

Smart Meter Verification has an output mode called Continuous Measurement that allows the transmitter to keep measuring while the test is in progress. If you choose to run the test in Last Measured Value or Fault modes instead, the transmitter outputs will be held constant for the two minute duration of the test. If control loops depend on transmit[...]

Option Description Last Value During the test, all outputs will go to their configured fault action. The test will run for approximately 140 seconds. While the test is in progress, dots traverse the display and test progress is shown. Postrequisites View the test results and take any appropriate actions. Measurement support 176 Micro Motion ® Mode[...]

Smart Meter Verification flowchart: Running a test using the display Running a Smart Meter Verification test using the display Figure 11-2: OUTPUTS ARE YOU SURE/YES? . . . . . . . . . . . . . . . x % P ASS VERFY ABORTED VERFY CAUTION VERFY Fail Abort RERUN/YES? Y es No Correct condition RUN VERFY CONTINUE MEASR F AUL T LAST V ALUE Select Scroll Scr[...]

You may need to wait a few seconds while ProLink II synchronizes its database with the transmitter data. 2. Review the information presented on the screen, and click Next . 3. Enter any desired information on the Test Definition screen, and click Next . All information on this screen is optional. 4. Choose the desired output behavior. Option Descri[...]

Postrequisites View the test results and take any appropriate actions. Run a Smart Meter Verification test using the Field Communicator 1. Navigate to the Smart Meter Verification menu: • Overview > Shortcuts > Meter Verification • Service Tools > Maintenance > Routine Maintenance > Meter Verification 2. Choose Manual Verificatio[...]

• Current flowmeter identification data • Current flow and density configuration parameters • Current zero values • Current process values for mass flow rate, volume flow rate, density, temperature, and external pressure • Customer and test descriptions (if entered by the user) If you use ProLink II or ProLink III to run a test, a test re[...]

Smart Meter Verification flowchart: Viewing test results using the display Viewing Smart Meter Verification test results using the display Figure 11-4: RESUL TS READ Select xx L STF% RUNCOUNT x Select xx HOURS Select P ASS Select xx R STF% Select RESUL TS MORE? Select Scroll T o Run V erfy Pass Select Scroll Result type Fail Abort xx HOURS Select C[...]

View test result data using ProLink II 1. Choose Tools > Meter Verification > Run Meter Verification and click View Previous Test Results and Print Report . The chart shows test results for all tests stored in the ProLink II database. 2. (Optional) Click Next to view and print a test report. 3. (Optional) Click Export Data to CSV File to save[...]

Fail The test result is not within the specification uncertainty limit. Micro Motion recommends that you immediately repeat the meter verification test. If during the failed test you had set outputs to Continue Measurement , set outputs to Fault or Last Measured Value instead. • If the meter passes the second test, the first result can be ignored[...]

Manage scheduled test execution using the display 1. Navigate to the Smart Meter Verification menu. Smart Meter Verification – Top-level menu Figure 11-5: Scroll and Select simultaneously for 4 seconds ENTER METER VERFY Scroll RUN VERFY RESUL TS READ SCHEDULE VERFY Select EXIT Scroll Scroll Scroll Scroll Select Select Select Select 2. Scroll to S[...]

Smart Meter Verification flowchart: Scheduling test execution using the display Scheduling Smart Meter Verification test execution using the display Figure 11-6: SCHEDULE VERFY Select SA VE/YES? TURN OFF SCHED/YES? SET NEXT Select Select Schedule set? Y es Schedule deleted Scroll HOURS LEFT Select Scroll xx HOURS SET RECUR No SCHED IS OFF xx HOURS [...]

4. To disable scheduled execution: • To disable execution of a single scheduled test, set Hours Until Next Run to 0. • To disable recurring execution, set Hours Between Recurring Runs to 0. • To disable all scheduled execution, click Turn Off Schedule . Manage scheduled test execution using ProLink III 1. Choose Device Tools > Diagnostics [...]

• The zero is required by site procedures. • The stored zero value fails the Zero Verification procedure. Prerequisites Before performing a field zero, execute the Zero Verification procedure to see whether or not a field zero can improve measurement accuracy. See Section 2.6 . Important Do not verify the zero or zero the flowmeter if a high-se[...]

2. Navigate to OFFLINE MAINT > ZERO > CAL ZERO and select CAL/YES? . Dots traverse the display while flowmeter zero is in progress. 3. Read the zero result on the display. The display reports CAL PASS if the zero was successful, or CAL FAIL if it was not. Postrequisites Restore normal flow through the sensor by opening the valves. Need help? [...]

3. Click Calibrate Zero . 4. Modify Zero Time , if desired. Zero Time controls the amount of time the transmitter takes to determine its zero- flow reference point. The default Zero Time is 20 seconds. For most applications, the default Zero Time is appropriate. 5. Click Perform Auto Zero . The Calibration in Progress light will turn red during the[...]

a. Allow the flowmeter to warm up for at least 20 minutes after applying power. b. Run the process fluid through the sensor until the sensor temperature reaches the normal process operating temperature. c. Stop flow through the sensor by shutting the downstream valve, and then the upstream valve if available. d. Verify that the sensor is blocked in[...]

11.3.4 Zero the flowmeter using the Field Communicator Zeroing the flowmeter establishes a baseline for process measurement by analyzing the sensor's output when there is no flow through the sensor tubes. 1. Prepare the flowmeter: a. Allow the flowmeter to warm up for at least 20 minutes after applying power. b. Run the process fluid through t[...]

11.4 Validate the meter Display OFF-LINE MAINT > CONFG > UNITS > MTR F ProLink II ProLink > Configuration > Flow ProLink III Device Tools > Configuration > Process Measurement > Flow Device Tools > Configuration > Process Measurement > Density Field Communicator Configure > Manual Setup > Measurements > Flo[...]

Procedure 1. Determine the meter factor as follows: a. Use the flowmeter to take a sample measurement. b. Measure the same sample using the reference device. c. Calculate the meter factor using the following formula: NewMeterFactor ConfiguredMeterFactor ReferenceMeasurement FlowmeterMeasurement = x 2. Ensure that the calculated meter factor is betw[...]

MeterFactor V olume 1 MeterFactor Density = Note The following equation is mathematically equivalent to the first equation. You may use whichever version you prefer. MeterFactor V olume ConfiguredMeterFactor Density Density Flowmeter Density ReferenceDevice = x 3. Ensure that the calculated meter factor is between 0.8 and 1.2, inclusive. If the met[...]

• If LD Optimization is enabled on your meter, disable it. To do this, choose ProLink > Configuration > Sensor and ensure that the checkbox is not checked. LD Optimizatio n is used only with large sensors in hydrocarbon applications. In some installations, only Micro Motion customer service has access to this parameter. If this is the case,[...]

Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. 11.5.2 Perform a D1 and D2 density calibration using ProLink III Prerequisites • During density calibration, the sensor must be completely filled with the calibration fluid, and flow through the sensor must be at the lowest rate allowed by your applicat[...]

D1 and D2 density calibration using ProLink III Figure 11-8: Enter density of D1 fluid D1 calibration Close shutoff valve downstream from sensor Fill sensor with D1 fluid Done Device T ools > Calibration > Density Calibration > Density Calibration – Point 1 (Air) Close Start Calibration Enter density of D2 fluid D2 calibration Fill senso[...]

• Before performing the calibration, record your current calibration parameters. If the calibration fails, restore the known values. Restriction For T-Series sensors, the D1 calibration must be performed on air and the D2 calibration must be performed on water. Procedure See Figure 11-9 . D1 and D2 density calibration using the Field Communicator[...]

11.6 Perform a D3 and D4 density calibration (T- Series sensors only) For T-Series sensors, the optional D3 and D4 calibration could improve the accuracy of the density measurement if the density of your process fluid is less than 0.8 g/cm 3 or greater than 1.2 g/cm 3 . If you perform the D3 and D4 calibration, note the following: • Do not perfor[...]

D3 or D3 and D4 density calibration using ProLink II Figure 11-10: Enter density of D3 fluid Calibration in Progress light turns green Calibration in Progress light turns red D3 calibration Close shutoff valve downstream from sensor Fill sensor with D3 fluid Close Enter density of D4 fluid Calibration in Progress light turns green Calibration in Pr[...]

- Minimum difference of 0.1 g/cm 3 between the density of the D4 fluid and the density of the D3 fluid. The density of the D4 fluid must be greater than the density of the D3 fluid. - Minimum difference of 0.1 g/cm 3 between the density of the D4 fluid and the density of water. The density of the D4 fluid may be either greater or less than the dens[...]

• For D3 density calibration, the D3 fluid must meet the following requirements: - Minimum density of 0.6 g/cm 3 - Minimum difference of 0.1 g/cm 3 between the density of the D3 fluid and the density of water. The density of the D3 fluid may be either greater or less than the density of water. • For D4 density calibration, the D4 fluid must mee[...]

D3 or D3 and D4 density calibration using the Field Communicator Figure 11-12: Enter density of D3 fluid Density Calibration Complete message Calibration in Progress message D3 calibration Close shutoff valve downstream from sensor Fill sensor with D3 fluid Fill sensor with D4 fluid D4 calibration OK Dens Pt 3 T -Series Calibration method executes [...]

Important Consult Micro Motion before performing a temperature calibration. Under normal circumstances, the temperature circuit is stable and should not need an adjustment. Procedure See Figure 11-13 and Figure 11-14 . Temperature calibration using ProLink II Figure 11-13: Enter temperature of low- temperature fluid T emperature Offset calibration [...]

Temperature calibration using ProLink III Figure 11-14: Enter temperature of low- temperature fluid T emperature Offset calibration W ait until sensor achieves thermal equilibrium Fill sensor with low- temperature fluid Enter temperature of high- temperature fluid T emperature Slope calibration Start Calibration W ait until sensor achieves thermal [...]

Measurement support 206 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

12 Troubleshooting Topics covered in this chapter: • Status LED states • Status alarms • Flow measurement problems • Density measurement problems • Temperature measurement problems • Milliamp output problems • Frequency output problems • Use sensor simulation for troubleshooting • Check power supply wiring • Check sensor-to-tran[...]

12.1 Status LED states The status LED on the transmitter indicates whether or not alarms are active. If alarms are active, view the alarm list to identify the alarms, then take appropriate action to correct the alarm condition. Your transmitter has a status LED only if it has a display. If the transmitter has a display and LED Blinking is disabled,[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A003 No Sensor Response The transmitter is not receiving one or more basic electrical sig- nals from the sensor. This could mean that the wiring between the sensor and the transmitter has been damaged, or that the sensor requires factory service[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A005 Mass Flow Rate Overrange The sensor is signaling a flow rate that is out of range for the sen- sor. 1. If other alarms are present, resolve those alarm conditions first. If the current alarm persists, continue with the recom- mended actions[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A008 Density Overrange The sensor is signaling a density reading below 0 g/cm 3 or above 10 g/cm 3 . Common causes for this alarm include partially filled flow tubes, excessive gas entrainment or flashing, tube fouling (foreign material stuck in[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A010 Calibration Failure This alarm is typically caused by flow through the sensor during the zero, or by a zero offset result that is out of range. Power to the transmitter must be cycled to clear this alarm. 1. Cycle power to the meter. 2. Mak[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A016 Sensor RTD Failure The sensor RTD is signaling a resistance that is out of range for the sensor. 1. Check the wiring between the sensor and the transmitter. a. Using the installation manual for your transmitter, verify that the transmitter [...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A019 RAM Error (Transmitter) Power to the transmitter must be cycled to clear this alarm. 1. Check that all wiring compartment covers are installed prop- erly. 2. Check that the wiring connected to the transmitter meets specifications and that s[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A026 Sensor/Transmitter Communi- cations Failure The transmitter has lost communication with the core processor on the sensor. This alarm can be an indication of a problem with the core or the transmitter requiring the replacement of one or both[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A031 Low Power The core processor on the sensor is not receiving sufficient pow- er. Check the wiring between the transmitter and the sensor. Power to the transmitter must be cycled to clear this alarm. 1. Using the installation manual for your [...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A100 mA Output 1 Saturated The calculated mA output value is outside of the meter's config- ured range. 1. Check the Upper Range Value and Lower Range Value parame- ters. Are they set correctly? 2. Check your process conditions against the [...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A110 Frequency Output Saturated The calculated frequency output is outside the configured range. 1. Check the Frequency Output Scaling Method parameter. 2. Check your process conditions against the values reported by the flowmeter. 3. Verify pro[...]

Status alarms and recommended actions (continued) Table 12-2: Alarm code Description Recommended actions A117 Density Overrange (Petrole- um) 1. Check your process conditions against the values reported by the flowmeter. 2. Verify the configuration of the petroleum measurement ta- ble type and density. A118 Discrete Output 1 Fixed The discrete outp[...]

12.3 Flow measurement problems Flow measurement problems and recommended actions Table 12-3: Problem Possible causes Recommended actions Flow indication at no flow conditions or zero offset • Misaligned piping (especially in new in- stallations) • Open or leaking valve • Incorrect sensor zero • Verify that all of the characterization parame[...]

Flow measurement problems and recommended actions (continued) Table 12-3: Problem Possible causes Recommended actions Erratic non-zero flow rate when flow is steady • Slug flow • Damping value too low • Plugged or coated flow tube • Output wiring problem • Problem with receiving device • Wiring problem • Verify that the sensor orienta[...]

12.4 Density measurement problems Density measurement problems and recommended actions Table 12-4: Problem Possible causes Recommended actions Inaccurate density reading • Problem with process fluid • Incorrect density calibration factors • Wiring problem • Incorrect flowmeter grounding • Slug flow • Plugged or coated flow tube • Inco[...]

12.5 Temperature measurement problems Temperature measurement problems and recommended actions Table 12-5: Problem Possible causes Recommended actions Temperature reading significantly different from process temper- ature • RTD failure • Wiring problem • Check junction box for moisture or verdi- gris. • Perform RTD resistance checks and che[...]

12.6 Milliamp output problems Milliamp output problems and recommended actions Table 12-6: Problem Possible causes Recommended actions No mA output • Wiring problem • Circuit failure • Channel not configured for desired output • Check the power supply and power supply wiring. See Section 12.9 . • Check the mA output wiring. • Check the [...]

Milliamp output problems and recommended actions (continued) Table 12-6: Problem Possible causes Recommended actions mA output consis- tently out of range • Incorrect process variable or units assigned to output • Fault condition if fault action is set to up- scale or downscale • LRV and URV are not set correctly • Verify the output variabl[...]

Frequency output problems and recommended actions Table 12-7: Problem Possible causes Recommended actions No frequency output • Stopped totalizer • Process condition below cutoff • Fault condition if fault action is set to in- ternal zero or downscale • Slug flow • Flow in reverse direction from config- ured flow direction parameter • B[...]

For more information on using sensor simulation using ProLink II, see Section 7.1 . 12.9 Check power supply wiring If the power supply wiring is damaged or improperly connected, the transmitter may not receive enough power to operate properly. Prerequisites You will need the installation manual for your transmitter. Procedure 1. Before inspecting t[...]

Prerequisites You will need the installation manual for your transmitter. Procedure 1. Before opening the wiring compartments, disconnect the power source. CAUTION! If the transmitter is in a hazardous area, wait five minutes after disconnecting the power. 2. Verify that the transmitter is connected to the sensor according to the information provid[...]

Follow appropriate procedures to ensure that loop testing will not interfere with existing measurement and control loops. Procedure 1. Test the mA output(s). a. Choose and select a low value, e.g., 4 mA. Dots traverse the display while the output is fixed. b. Read the mA current at the receiving device and compare it to the transmitter output. The [...]

c. At the transmitter, activate Select . d. Scroll to and select SET OFF . e. Verify the signal at the receiving device. f. At the transmitter, activate Select . Postrequisites • If the mA output reading was slightly off at the receiving device, you can correct this discrepancy by trimming the output. • If the mA output reading was significantl[...]

i. Click UnFix mA . 2. Test the frequency output(s). Note If the Weights & Measures application is enabled on the transmitter, it is not possible to perform a loop test of the frequency output, even when the transmitter is unsecured. a. Choose ProLink > Test > Fix Freq Out . b. Enter the frequency output value in Set Output To . c. Click [...]

Procedure 1. Test the mA output(s). a. Choose Device Tools > Diagnostics > Testing > mA Output 1 Test or Device Tools > Diagnostics > Testing > mA Output 2 Test . b. Enter 4 in Fix to: . c. Click Fix mA . d. Read the mA current at the receiving device and compare it to the transmitter output. The readings do not need to match exac[...]

f. Click UnFix . 12.12.4 Perform loop tests using the Field Communicator Tip Loop tests are not required. However, Micro Motion recommends performing a loop test for every input or output available on your transmitter. The inputs and outputs available on your transmitter vary according to your purchase option and your channel configuration. You may[...]

b. Read the frequency signal at the receiving device and compare it to the transmitter output. c. Choose End . 3. Test the discrete output(s). a. Press Service Tools > Simulate > Simulate Outputs > Discrete Output Test . b. Choose Off . c. Verify the signal at the receiving device. d. Press OK . e. Choose On . f. Verify the signal at the r[...]

12.14 Check the HART communication loop If you cannot establish or maintain HART communications, the HART loop may be wired incorrectly. Prerequisites You will need: • A copy of your transmitter installation manual • A Field Communicator • Optional: the HART Application Guide , available at www.hartcomm.org Procedure 1. Verify that the loop w[...]

Procedure 1. Set HART Address as appropriate for your HART network. The default address is 0. This is the recommended value unless the transmitter is in a multidrop network. 2. Set Loop Current Mode to Enabled . 12.16 Check HART burst mode HART burst mode can cause the transmitter to output unexpected values. Burst mode is normally disabled, and sh[...]

• For the relevant status alarms, change the setting of Alarm Severity to Ignore . 3. If there are no active fault conditions, continue troubleshooting. 12.20 Check Frequency Output Maximum Pulse Width If Frequency Output Maximum Pulse Width is set incorrectly, the frequency output may report an incorrect value. Verify the configuration of Freque[...]

The Flow Direction parameter interacts with actual flow direction to affect flow values, flow totals and inventories, and output behavior. For the simplest operation, actual process flow should match the flow arrow that is on the side of the sensor case. Procedure 1. Verify the actual direction of process flow through the sensor. 2. Verify the conf[...]

12.26 Check the drive gain Excessive or erratic drive gain may indicate any of a variety of process conditions, sensor problems, or configuration problems. To know whether your drive gain is excessive or erratic, you must collect drive gain data during the problem condition and compare it to drive gain data from a period of normal operation. Excess[...]

Possible causes and recommended actions for erratic drive gain (continued) Table 12-9: Possible cause Recommended actions Polarity of pick-off reversed or polarity of drive reversed Contact Micro Motion. Slug flow Check for slug flow. See Section 12.25 . Foreign material caught in flow tubes • Purge the flow tubes. • Replace the sensor. 12.26.1[...]

Possible causes and recommended actions for low pickoff voltage (continued) Table 12-10: Possible cause Recommended actions No tube vibration in sensor • Check for plugging. • Ensure sensor is free to vibrate (no mechanical binding). • Verify wiring. • Test coils at sensor. See Section 12.28.1 . Moisture in the sensor elec- tronics Eliminat[...]

12.28.1 Check the sensor coils Checking the sensor coils can identify electrical shorts. Restriction This procedure applies only to 9-wire remote-mount transmitters and remote transmitters with remote core processors.. Procedure 1. Disconnect power to the transmitter. CAUTION! If the transmitter is in a hazardous area, wait 5 minutes before continu[...]

a. Leave the terminal blocks disconnected. b. Remove the lid of the junction box. c. Testing one terminal at a time, place a DMM lead on the terminal and the other lead on the sensor case. With the DMM set to its highest range, there should be infinite resistance on each lead. If there is any resistance at all, there is a short to case. 6. Test the[...]

a. Remove the core processor lid. The core processor is intrinsically safe and can be opened in all environments. b. Check the state of the core processor LED. 3. If you have an integral installation: a. Loosen the four cap screws that fasten the transmitter to the base. Integral installation components Figure 12-1: Base 4 x cap screws (4 mm) Trans[...]

9-wire remote installation components Figure 12-2: Transmitter Core processor 4 x cap screws (4 mm) End-cap b. Inside the core processor housing, loosen the three screws that hold the core processor mounting plate in place. Do not remove the screws. c. Rotate the mounting plate so that the screws are in the unlocked position. d. Holding the tab on [...]

3. Tighten the screws, torquing to 6 to 8 in-lbs (0.7 to 0.9 N-m). 4. Replace the end-cap. Important When reassembling the meter components, be sure to grease all O-rings. 12.29.1 Core processor LED states Standard core processor LED states Table 12-13: LED state Description Recommended actions 1 flash per second (ON 25%, OFF 75%) Normal operation [...]

Enhanced core processor LED states (continued) Table 12-14: LED state Description Recommended action Solid red High-severity alarm Check alarm status. Flashing red (80% on, 20% off) Tubes not full • If alarm A105 (slug flow) is active, refer to the recommended actions for that alarm. • If alarm A033 (tubes not full) is active, verify process. C[...]

Integral installation components Figure 12-3: Base 4 x cap screws (4 mm) Transition ring Transmitter Core processor b. Rotate the transmitter counter-clockwise so that the cap screws are in the unlocked position. c. Gently lift the transmitter straight up, disengaging it from the cap screws. 4. If you have a 9-wire remote installation: a. Remove th[...]

5. At the core processor, disconnect the 4-wire cable between the core processor and the transmitter. 6. Measure the resistance between core processor terminal pairs 3–4, 2–3, and 2–4. Terminal pair Function Expected resistance 3–4 RS-485/A and RS-485/B 40 k Ω to 50 k Ω 2–3 VDC– and RS-485/A 20 k Ω to 25 k Ω 2–4 VDC– and RS-485/[...]

Troubleshooting 250 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Appendix A Using the transmitter display Topics covered in this appendix: • Components of the transmitter interface • Use the optical switches • Access and use the display menu system • Display codes for process variables • Codes and abbreviations used in display menus • Menu maps for the transmitter display A.1 Components of the transm[...]

Transmitter interface Figure A-1: A B C D E F G H A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator F. Select optical switch G. Unit of measure for process variable H. Current value of process variable A.2 Use the optical switches Use the optical switches on the transmitter interface to co[...]

Optical switch indicator and optical switch states Table A-1: Optical switch indicator State of optical switches Solid red One optical switch is activated. Flashing red Both optical switches are activated. A.3 Access and use the display menu system The display menu system is used to perform various configuration, administrative, and maintenance tas[...]

Tip If you do not know the correct value for Off-Line Password , wait 30 seconds. The password screen will time out automatically and you will be returned to the previous screen. 4. If Scroll flashes on the display, activate the Scroll optical switch, then the Select optical switch, and then the Scroll optical switch again. The display will prompt [...]

Procedure • To change the value: 1. Activate Select until the digit you want to change is active (flashing). Select moves the cursor one position to the left. From the leftmost position, Select moves the cursor to the rightmost digit. 2. Activate Scroll to change the value of the active digit. 3. Repeat until all digits are set as desired. • To[...]

• To exit the menu without saving the displayed value to transmitter memory, activate Scroll and Select simultaneously and hold until the display changes. - If the displayed value is the same as the value in transmitter memory, you will be returned to the previous screen. - If the displayed value is not the same as the value in transmitter memory[...]

b. Activate Scroll until the desired character is displayed. c. Activate Select to move the cursor one digit to the left. d. Activate Scroll until the desired character is displayed. e. Activate Select to move the cursor one digit to the left. f. Activate Scroll until the desired character is displayed. g. Activate Select to move the cursor one dig[...]

Display codes for process variables (continued) Table A-2: Code Definition Comment or reference FVZ Field verification zero Weights & Measures application only GSV F Gas standard volume flow GSV I Gas standard volume inventory GSV T Gas standard volume total LPO_A Left pickoff amplitude LVOLI Volume inventory LZERO Live zero flow MASSI Mass inv[...]

A.5 Codes and abbreviations used in display menus Codes and abbreviations used in display menus Table A-3: Code or abbrevi- ation Definition Comment or reference ACK ALARM Acknowledge alarm ACK ALL Acknowledge all alarms ACT Action ADDR Address AO 1 SRC Fixed to the process variable assigned to the primary out- put AO1 Analog output 1 (primary mA o[...]

Codes and abbreviations used in display menus (continued) Table A-3: Code or abbrevi- ation Definition Comment or reference ENABLE ALARM Enable alarm menu Access to alarm menu from display ENABLE AUTO Enable Auto Scroll Enable or disable the Auto Scroll func- tion ENABLE OFFLN Enable off-line Access to off-line menu from display ENABLE PASSW Enable[...]

Codes and abbreviations used in display menus (continued) Table A-3: Code or abbrevi- ation Definition Comment or reference MASS Mass flow MBUS Modbus MFLOW Mass flow MSMT Measurement OFFLN Off-line OFF-LINE MAINT Off-line maintenance P/UNT Pulses/unit POLAR Polarity PRESS Pressure QUAD Quadrature r. Revision SCALE Scaling method SIM Simulation Use[...]

A.6 Menu maps for the transmitter display Offline menu – top level Figure A-2: Scroll and Select simultaneously for 4 seconds VER OFF-LINE MAINT Select SEE ALARM Scroll Scroll EXIT CONFG Scroll SIM ZERO SENSOR VERFY* Scroll Scroll Scroll Scroll EXIT *This option is displayed only if the transmitter is connected to an enhanced core processor and t[...]

Offline menu – version information Figure A-3: Scroll and Select simultaneously for 4 seconds VER Y es V ersion info Scroll Select Y es CEQ/ETO info* Scroll CUSTODY XFER* Scroll Y es SENSOR VERFY* Scroll Scroll EXIT OFF-LINE MAINT Select Scroll ED/API info* Scroll *The option is displayed only if the corresponding CEQ/ ET O or application is inst[...]

Offline menu – configuration: units and I/O Figure A-4: OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select Scroll CONFG MASS UNITS VOL/GSV DENS TEMP Select Scroll Scroll Scroll AO 1 SRC AO 1 4 MA AO 120 MA Scroll Scroll EXIT Scroll Scroll PRESS FO FO SRC FO FREQ Select Scroll Scroll Scroll FO RA TE Scroll FO POLAR [...]

Offline menu – configuration: meter factor, display, and digital communications Figure A-5: OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select Scroll CONFG UNITS MASS MTR F VOL Select Scroll Scroll DENS EXIT Scroll Scroll Scroll TOT ALS RESET DISPLA Y TOT ALS STOP DISPLA Y OFFLN* Select Scroll Scroll Scroll DISPLA [...]

Offline menu – alarms Figure A-6: SEE ALARM Scroll and Select simultaneously for 4 seconds ACK ALL* Y es EXIT Select No Alarm code Scroll ACK Y es Select No Active/ unacknowledged alarms? No Y es Select NO ALARM EXIT Scroll Scroll Select Scroll Scroll Select *This screen is displayed only if the ACK ALL function s enabled and there are unacknowle[...]

Offline menu – meter verification: top level Figure A-7: Scroll and Select simultaneously for 4 seconds ENTER METER VERFY Scroll RUN VERFY RESUL TS READ SCHEDULE VERFY Select EXIT Scroll Scroll Scroll Scroll Select Select Select Select Offline menu – meter verification schedule Figure A-8: SCHEDULE VERFY Select SA VE/YES? TURN OFF SCHED/YES? SE[...]

Offline menu – meter verification test Figure A-9: OUTPUTS ARE YOU SURE/YES? . . . . . . . . . . . . . . . x % P ASS VERFY ABORTED VERFY CAUTION VERFY Fail Abort RERUN/YES? Y es No Correct condition RUN VERFY CONTINUE MEASR FAUL T LAST V ALUE Select Scroll Scroll Scroll Select Scroll RESUL TS VIEW/YES? Select Scroll Scroll Select Select Select Se[...]

Offline menu – meter verification results Figure A-10: RESUL TS READ Select xx L STF% RUNCOUNT x Select xx HOURS Select P ASS Select xx R STF% Select RESUL TS MORE? Select Scroll T o Run V erfy Pass Select Scroll Result type Fail Abort xx HOURS Select CAUTION xx L STF% xx R STF% Select Select xx HOURS Abort T ype T o Runcount x -1 Select Select S[...]

Offline menu – totalizers and inventories Figure A-11: RESET (3) Select Scroll STOP/ST ART (2) RESET YES? Process variable display STOP/ST ART YES? Scroll Mass total V olume total Scroll Select Y es No Select Scroll EXIT Select Y es No Select Scroll Scroll E1--SP (1) E2--SP (1) Scroll Scroll Scroll (1) The Event Setpoint screens can be used to de[...]

Offline menu – Simulation (loop testing) Figure A-12: Scroll and Select simultaneously for 4 seconds Y es Scroll Select AO SIM FO SIM DO SIM Scroll Select SET x MA* Y es Select** SET y KHZ**** Select SET OFF SET ON Select EXIT Scroll Scroll Select*** . . . . . . . . . . . . . . . . EXIT Y es Select** Scroll Select*** . . . . . . . . . . . . . . .[...]

Offline menu – Zero Figure A-13: …………………. OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select CAL ZERO Troubleshoot ZERO/YES? CAL P ASS CAL F AIL RESTORE ZERO RESTORE ZERO/YES? Current zero display Factory zero display Select Select Y es No EXIT Scroll Select Scroll Scroll Scroll Y es Select No Scroll [...]

Appendix B Using ProLink II with the transmitter Topics covered in this appendix: • Basic information about ProLink II • Connect with ProLink II • Menu maps for ProLink II B.1 Basic information about ProLink II ProLink II is a software tool available from Micro Motion. It runs on a Windows platform and provides complete access to transmitter [...]

ProLink II messages As you use ProLink II with a Micro Motion transmitter, you will see a number of messages and notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safety messages. B.2 Connect with ProLink II A connection from ProLink II[...]

B.2.2 Make a service port connection CAUTION! If the transmitter is in a hazardous area, do not use a service port connection. Service port connections require opening the wiring compartment, and opening the wiring compartment while the transmitter is powered up could cause an explosion. To connect to the transmitter in a hazardous environment, use[...]

Connection to service port Figure B-1: A C D E B A. PC B. Signal converter C. Service port terminal 7 (RS-485/A) D. Service port terminal 8 (RS-485/B) E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 4. Start ProLink II. 5. Choose Connect[...]

CAUTION! If the transmitter is in a hazardous area, do not connect directly to the transmitter terminals. Connecting directly to the transmitter terminals requires opening the wiring compartment, and opening the wiring compartment while the transmitter is powered up could cause an explosion. To connect to the transmitter in a hazardous environment,[...]

Connection to transmitter terminals Figure B-2: A C D B A. PC B. Signal converter C. 250–600 Ω resistance D. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 3. To connect from a point in the local HART loop: a. Attach the leads from the[...]

Connection over local loop Figure B-3: A C D E R1 R3 R2 B A. PC B. Signal converter C. Any combination of resistors R1, R2, and R3 as necessary to meet HART communication resistance requirements D. DCS or PLC E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections [...]

Connection over multidrop network Figure B-4: B A C D A. Signal converter B. 250–60 0 Ω resistance C. Devices on the network D. Master device 5. Start ProLink II. 6. Choose Connection > Connect to Device . 7. Set Protocol to HART Bell 202 . Tip HART/Bell 202 connections use standard connection parameters. You do not need to configure them he[...]

Option Description Primary Use this setting if no other host is on the network. The Field Communicator is not a host. 12. Click Connect . Need help? If an error message appears: • Verify the HART address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitte[...]

Tip HART connections are not polarity-sensitive. It does not matter which lead you attach to which terminal. Connection to transmitter terminals Figure B-5: A C B A. PC B. Signal converter C. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. [...]

Connection over network Figure B-6: A C E D B A. PC B. Signal converter C. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLC E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 4. Start ProLink II. 5. Choo[...]

Option Description Secondary Use this setting if another HART host such as a DCS is on the network. Primary Use this setting if no other host is on the network. The Field Communicator is not a host. 9. Click Connect . Need help? If an error message appears: • Verify the HART address of the transmitter. • Ensure that you have specified the corre[...]

Tip Usually, but not always, the black lead is RS-485/A and the red lead is RS-485/B. Connection to transmitter terminals Figure B-7: A C B A. PC B. Signal converter C. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 3. To connect over the [...]

Connection over network Figure B-8: A C E D B A. PC B. Signal converter C. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLC E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 4. Start ProLink II. 5. Choo[...]

Need help? If an error message appears: • Verify the Modbus address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitter. • Increase or decrease resistance. • For long-distance communication, or if noise from an external source interferes with the sig[...]

Main menu (continued) Figure B-10: Data Logging* Enable/Disable Custody T ransfer T ools Plug-ins ProLink Configuration Output Levels Process V ariables Status Alarm Log Diagnostic Information Calibration T est ED T otalizer Control API T otalizer Control CM T otalizer Control T otalizer Control Core Processor Diagnostics Finger Print API Process V[...]

Configuration menu Figure B-11: Flow • Flow Direction • Flow Damp • Flow Cal • Mass Flow Cutoff • Mass Flow units • Mass Factor • Dens Factor • V ol Factor • Flow Switch V ariable • Flow Switch Setpoint • Flow Switch Hysteresis • V ol Flow Cutoff • V ol Flow Units • V ol Flow T ype • Std Gas V ol Flow Cutoff • Std Ga[...]

Configuration menu (continued) Figure B-12: T emperature • T emp Units • T emp Cal Factor • T emp Damping • External T emperature • External RTD Frequency/Discrete Output • Frequency • T ertiary V ariable • Freq Factor • Rate Factor • Freq Pulse Width • Last Measured V alue T imeout • Scaling Method • Pulses Per lbs • lb[...]

Configuration menu (continued) Figure B-13: ProLink > Configuration Additional configuration options Device • Model • Manufacturer • Hardware Rev • Distributor • Software Rev • ET O • CP Software Rev • CP ET O • Option Board • Firmware Checksum • CP Firmware Checksum • T ag • Date • Descriptor • Message • Sensor t[...]

Configuration menu (continued) Figure B-14: ProLink > Configuration Polled V ariables Pol led V ariable 1/2 • Polling Control • External T ag • V ariable T ype • Current V alue Discrete Events • Event Name • Even t T ype • Process V ariable • Low Setpoint (A) • High Setpoint (B) Alarm • Alarm • Severity Events Event 1/2 •[...]

Configuration menu (continued) Figure B-15: ProLink > Configuration Additional configuration options Display • mA1 • V ar1...V ar15 • Display Precision • V ar • Number of Decimals • Display Language • Display Start/Stop T otalizers • Display T otalizer Reset • Display Auto Scroll • Display Offline Menu • Display Offline Pas[...]

Configuration menu (continued) Figure B-16: ProLink > Configuration T ransmitter Options • V olume Flow • Meter Fingerprinting • Cryogenic Moduls Compensation • Core Processor Options • Batcher Functions • Meter V erification • Net Oil Computing • Flow V elocity • Special Density Functions • Function Block Option • Viscosit[...]

Configuration menu (continued) Figure B-17: ProLink > Configuration Sensor • Sensor s /n • Sensor Model • Sensor Matl • Liner Matl • Flange API Setup • Generalized Crude or JP 4 • Generalized Products • User Defined TEC • Generalized Lubricants • Degrees API, Reference T emperature is 60° F • Kg/ms @ Reference T emp System[...]

Configuration menu (continued) Figure B-18: ProLink > Configuration Sensor Simulation • Enable/disable • Mass flow • W ave form • Fixed value • Period • Minimum • Maximum • Density • W ave form • Fixed value • Period • Minimum • Maximum • T emperature • W ave form • Fixed value • Period • Minimum • Maximum C[...]

Appendix C Using ProLink III with the transmitter Topics covered in this appendix: • Basic information about ProLink III • Connect with ProLink III • Menu maps for ProLink III C.1 Basic information about ProLink III ProLink III is a configuration and service tool available from Micro Motion. It runs on a Windows platform and provides complete[...]

ProLink III messages As you use ProLink III with a Micro Motion transmitter, you will see a number of messages and notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safety messages. C.2 Connect with ProLink III A connection from ProLink[...]

C.2.2 Make a service port connection CAUTION! If the transmitter is in a hazardous area, do not use a service port connection. Service port connections require opening the wiring compartment, and opening the wiring compartment while the transmitter is powered up could cause an explosion. To connect to the transmitter in a hazardous environment, use[...]

Connection to service port Figure C-1: A C D E B A. PC B. Signal converter C. Service port terminal 7 (RS-485/A) D. Service port terminal 8 (RS-485/B) E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 4. Start ProLink III. 5. Choose Connec[...]

CAUTION! If the transmitter is in a hazardous area, do not connect directly to the transmitter terminals. Connecting directly to the transmitter terminals requires opening the wiring compartment, and opening the wiring compartment while the transmitter is powered up could cause an explosion. To connect to the transmitter in a hazardous environment,[...]

Connection to transmitter terminals Figure C-2: A C D B A. PC B. Signal converter C. 250–600 Ω resistance D. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 3. To connect from a point in the local HART loop: a. Attach the leads from the[...]

Connection over local loop Figure C-3: A C D E R1 R3 R2 B A. PC B. Signal converter C. Any combination of resistors R1, R2, and R3 as necessary to meet HART communication resistance requirements D. DCS or PLC E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections [...]

Connection over multidrop network Figure C-4: B A C D A. Signal converter B. 250–60 0 Ω resistance C. Devices on the network D. Master device 5. Start ProLink III. 6. Choose Connect to Physical Device . 7. Set Protocol to HART Bell 202 . Tip HART/Bell 202 connections use standard connection parameters. You do not need to configure them here. 8.[...]

Option Description Primary Use this setting if no other host is on the network. The Field Communicator is not a host. 12. Click Connect . Need help? If an error message appears: • Verify the HART address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitte[...]

Tip HART connections are not polarity-sensitive. It does not matter which lead you attach to which terminal. Connection to transmitter terminals Figure C-5: A C B A. PC B. Signal converter C. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. [...]

Connection over network Figure C-6: A C E D B A. PC B. Adapter, if necessary C. Signal converter D. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary E. DCS or PLC F. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 4. [...]

8. Set Master as appropriate. Option Description Secondary Use this setting if another HART host such as a DCS is on the network. Primary Use this setting if no other host is on the network. The Field Communicator is not a host. 9. Click Connect . Need help? If an error message appears: • Verify the HART address of the transmitter. • Ensure tha[...]

b. Connect the leads from the signal converter to terminals 5 (RS-485/A) and 6 (RS-485/B). Tip Usually, but not always, the black lead is RS-485/A and the red lead is RS-485/B. Connection to transmitter terminals Figure C-7: A C B A. PC B. Signal converter C. Transmitter, with wiring compartment and power supply compartment opened Note This figure [...]

Connection over network Figure C-8: A C E D B A. PC B. Signal converter C. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLC E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 4. Start ProLink III. 5. Cho[...]

Need help? If an error message appears: • Verify the Modbus address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitter. • Increase or decrease resistance. • For long-distance communication, or if noise from an external source interferes with the sig[...]

Device Tools: Configuration (with Weights & Measures) Figure C-10: Configuration: Process Measurement (with Concentration Measurement) Figure C-11: Using ProLink III with the transmitter 312 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Configuration: Process Measurement (with Petroleum Measurement) Figure C-12: Configuration: I/O Figure C-13: Using ProLink III with the transmitter Configuration and Use Manual 313[...]

Configuration: Transmitter Display Figure C-14: Configuration: Events Figure C-15: Using ProLink III with the transmitter 314 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Configuration: Communications Figure C-16: Configuration: Informational Parameters Figure C-17: Using ProLink III with the transmitter Configuration and Use Manual 315[...]

Device Tools: Calibration Figure C-18: Calibration: Density Calibration Figure C-19: Using ProLink III with the transmitter 316 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Calibration: Temperature Calibration Figure C-20: Device Tools: Configuration Transfer Figure C-21: Using ProLink III with the transmitter Configuration and Use Manual 317[...]

Diagnostics: Testing Figure C-22: Diagnostics: Meter Verification Figure C-23: Using ProLink III with the transmitter 318 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Device Tools: Trending Figure C-24: Using ProLink III with the transmitter Configuration and Use Manual 319[...]

Using ProLink III with the transmitter 320 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Appendix D Using the Field Communicator with the transmitter Topics covered in this appendix: • Basic information about the Field Communicator • Connect with the Field Communicator • Menu maps for the Field Communicator D.1 Basic information about the Field Communicator The Field Communicator is a handheld configuration and management tool th[...]

If Micro Motion is not listed, or you do not see the required device description, use the Field Communicator Easy Upgrade Utility to install the device description, or contact Micro Motion. Field Communicator menus and messages Many of the menus in this manual start with the On-Line menu. Ensure that you are able to navigate to the On-Line menu. As[...]

Field Communicator connection to transmitter terminals Figure D-1: A B C A. Field Communicator B. 250–60 0 Ω resistance C. Transmitter, with wiring compartment and power supply compartment opened 2. To connect to a point in the local HART loop, attach the leads from the Field Communicator to any point in the loop and add resistance as necessary[...]

Field Communicator connection to multidrop network Figure D-3: A B C D A. Field Communicator B. 250–60 0 Ω resistance C. Devices on the network D. Master device 4. Turn on the Field Communicator and wait until the main menu is displayed. 5. If you are connecting across a multidrop network: a. Set the Field Communicator to poll. The device retur[...]

On-Line menu Figure D-4: Configure 1 Manual Setup 2 Alert Setup Service T ools 1 Alerts 2 V ariables 3 T rends 4 Maintenance 5 Simulate 2 3 Overview 1 Check Status 2 Primary Purpose V ariables 3 Shortcuts 1 On-Line Menu Using the Field Communicator with the transmitter Configuration and Use Manual 325[...]

Overview menu Figure D-5: Identification 1 T ag 2 Model 3 Xmtr Serial Num 4 Sensor Serial Num 5 Date 6 Descriptor 7 Message 1 Revisions 1 Universal 2 Field Device 3 DD Revision 4 T ransmitter Software 5 CP Software 6 ETO Number Mat. of Construction 1 T ube Wetted Mat. 2 T ube Lining 3 Sensor Flange Check Status 1 Refresh Alerts 2 Dev Status: 3 Comm[...]

Configure menu Figure D-6: Manual Setup 1 Characterize 2 Measurements 3 Display 4 Inputs/Outputs 5 Info Parameters 2 1 Alert Setup 1 I/O Fault Actions 2 Alert Severity 3 Discrete Events 4 CM Alerts On-Line Menu > 1 Configure Using the Field Communicator with the transmitter Configuration and Use Manual 327[...]

Manual Setup menu Figure D-7: Characterize 1 Sensor T ype 2 Sensor T ag Parameters Measurements 1 Flow 2 Density 3 T emperature 4 Update Rate 5 LD Optimization 6 Special Units 7 External Pressure/T emperature 8 Petroleum Measurement * 9 GSV 10 Conc Measure (CM) ** 1 2 Inputs/Outputs 1 Channels 2 mA Output 3 Frequency Output 4 Discrete Output 5 Comm[...]

Manual Setup menu: Characterize Figure D-8: On-Line Menu > 2 Configure > 1 Manual Setup > 1 Characterize 2 1 2 1 Sensor T ype Straight T ube Curved T ube Density Parameters 1 D1 2 D2 3 DT 4 DTG 5 K1 6 K2 7 FD 8 DFQ1 9 DFQ2 Flow Parameters 1 Flow FCF 2 FTG 3 FFQ Sensor T ag Parameters 1 Flow Parameters 2 Density Parameters Sensor T ag Param[...]

Manual Setup menu: Measurements Figure D-9: On-Line Menu > 2 Configure > 1 Manual Setup > 2 Measurements Flow 1 Flow Direction 2 Flow Damping 3 Mass Flow Unit 4 Mass Flow Cutoff 5 V olume Flow Unit * 6 V olume Flow Cutoff * 7 Mass Factor 8 V olume Factor Density 1 Density Unit 2 Density Damping 3 Density Cutoff 4 Density Factor 5 Slug Dura[...]

Manual Setup menu: Measurements (continued) Figure D-10: On-Line Menu > 2 Configure > 1 Manual Setup > 2 Measurements 1 2 3 8 7 9 10 Pressure 1 Pressure Unit 2 Pressure Compensation 3 Compensation Pressure 4 Flow Cal Pressure 5 Flow Press Factor 6 Dens Press Factor T emperature 1 T emperature Unit 2 External T emperature 3 Correction T emp[...]

Manual Setup menu: Display Figure D-11: On-Line Menu > 2 Configure > 1 Manual Setup > 3 Display Language English German French Spanish Display V ariable Menu Features 1 T otalizer Reset 2 Start/Stop T otals 3 Auto Scroll 4 Scroll T ime * 5 Refresh Rate 6 Status LED Blinking Offline V ariable Menu Features 1 Offline Menu 2 Alert Menu 3 Ackn[...]

Manual Setup menu: I/O Figure D-12: On-Line Menu > 2 Configure > 1 Manual Setup > 4 Inputs/Outputs mA Output 1 Primary V ariable 2 mA Output Settings 3 mA Fault Settings Frequency Output 1 FO Settings 2 FO Fault Parameters 3 FO Scaling 2 3 Milliamp Fault Settings 1 MAO Fault Action 2 MAO Fault Level mA Output Settings 1 PV LRV 2 PV URV 3 P[...]

Manual Setup menu: I/O (continued) Figure D-13: Discrete Output 1 DO Assignment 2 DO Polarity 3 DO Fault Action 4 Flow Switch Source 5 Flow Switch Setpoint 6 Hysteresis (0.1-10.0) 4 6 Map V ariables 1 Primary V ariable 2 Secondary V ariable 3 Third V ariable 4 Fourth V ariable 5 Communications 1 HART Address 2 T ag 3 Device Identification 4 Dev ID [...]

Alert Setup menu Figure D-14: On-Line Menu > 2 Configure > 2 Alert Setup I/O Fault Action 1 MAO Fault Action 2 MAO Fault Level 3 FO Fault Action 4 FO Fault Level 5 Comm Fault Action Alert Severity 1 Fault T imeout 2 Set Alert Severity 3 View Alert Severity Discrete Events 1 Discrete Event 1 2 Discrete Event 2 3 Discrete Event 3 4 Discrete Eve[...]

Service Tools menu Figure D-15: On-Line Menu > 3 Service T ools Alerts 1 Refresh Alerts Alert Name Additional Information V ariables 1 V ariable Summary 2 Process V ariables 3 Mapped V ariables 4 External V ariables 5 T otalizer Control 6 V ariables (PM) * 7 V ariables (CM) ** 8 Outputs 1 2 T rends 1 Process V ariables 2 Diagnostic V ariables 3 [...]

Service Tools menu: Variables Figure D-16: On-Line Menu > 3 Service T ools > 2 V ariables Process V ariables 1 Mass Flow Rate 2 V olume Flow Rate * 3 Density 4 T emperature Mapped V ariables 1 PV Mass Flow Rate 2 SV Mass Flow Rate 3 TV Mass Flow Rate 4 QV Mass Flow Rate 1 3 5 T otalizer Control 1 All T otalizers 2 Mass 3 V olume * 4 CM V olum[...]

Service Tools menu: Variables (continued) Figure D-17: Outputs 1 mA Output (MA0) 2 Frequency Output On-Line Menu > 3 Service T ools > 2 V ariables V ariables (PM) * 1 Density at Reference T emperature 2 Average Observed Density 3 V olume Flow at Reference T emperature 4 Average Observed T emperature 5 CTL V ariables (CM) ** 1 Standard V olume[...]

Service Tools menu: Maintenance Figure D-18: On-Line Menu > 3 Service T ools > 4 Maintenance Routine Maintenance 1 T rim mA Output 2 Meter V erification * 1 Zero Calibration 1 Mass Flow Rate 2 V olume Flow Rate 3 Zero T ime 4 Zero V alue 5 Standard Deviation 6 Perform Auto Zero 7 Restore Factory Zero Density Calibration 1 Mass Flow Rate 2 Den[...]

Service Tools menu: Simulate Figure D-19: On-Line Menu > 3 Service T ools > 5 Simulate 1 Simulate Outputs 1 mA Output Loop T est 2 Frequency Output T est/ Discrete Output T est * * Options vary depending on Channel settings . Simulate Sensor 1 Simulate Primary Purpose V ariables 2 Mass Flow Rate 3 Density 4 T emperature 2 Using the Field Comm[...]

Appendix E Default values and ranges E.1 Default values and ranges The default values and ranges represent the typical factory transmitter configuration. Depending on how the transmitter was ordered, certain values may have been configured at the factory and are not represented in the default values and ranges. Transmitter default values and ranges[...]

Transmitter default values and ranges (continued) Table E-1: Type Parameter Default Range Comments Density units g/cm 3 Density cutoff 0.2 g/cm 3 0.0 – 0.5 g/cm 3 D1 0 g/cm 3 D2 1 g/cm 3 K1 1000 µsec 1000 – 50,000 µsec K2 50,000 µsec 1000 – 50,000 µsec FD 0 Temp Coefficient 4.44 Slug flow Slug flow low limit 0.0 g/cm 3 0.0 – 10.0 g/ cm [...]

Transmitter default values and ranges (continued) Table E-1: Type Parameter Default Range Comments Base volume time sec Volume flow conversion factor 1 Variable map- ping Primary variable Mass flow Secondary variable Density Tertiary variable Mass flow Quaternary variable Volume flow mA output 1 Primary variable Mass flow LRV –200.00000 g/ s URV [...]

Transmitter default values and ranges (continued) Table E-1: Type Parameter Default Range Comments Fault action Downscale AO fault level – downscale 2.0 mA 1.0 – 3.6 mA AO fault level – upscale 22 mA 21.0 – 24.0 mA Last measured value timeout 0.00 sec LRV Mass flow rate − 200.000 g/s Volume flow rate − 0.200 l/s Density 0.000 g/cm 3 Tem[...]

Transmitter default values and ranges (continued) Table E-1: Type Parameter Default Range Comments Polarity Active low Display Backlight on/off On Backlight intensity 63 0 – 63 Refresh rate 200 millisec- onds 100 – 10,000 milliseconds Variable 1 Mass flow rate Variable 2 Mass total Variable 3 Volume flow rate Variable 4 Volume total Variable 5 [...]

Default values and ranges 346 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Appendix F Transmitter components and installation wiring Topics covered in this appendix: • Installation types • Power supply terminals and ground • Input/output (I/O) wiring terminals F.1 Installation types Model 1700 and Model 2700 transmitters can be installed five different ways, only one of which applies to your specific installation. ?[...]

High-temperature flexible conduit installation Figure F-2: High-temperature flexible conduit installations use the same installation instructions as 4-wire remote installations, except that the distance between the sensor and the electronics is limited by the length of the flexible conduit. • 4-wire remote – The transmitter is installed remotel[...]

4-wire remote installation – stainless steel housing Figure F-4: Sensor Core processor Transmitter 4-wire cable • 9-wire remote – The transmitter and core processor are combined in a single unit that is installed remotely from the sensor. You need to mount the transmitter/core processor assembly separately from the sensor, connect a 9-wire ca[...]

9-wire remote installation type Figure F-5: Transmitter Junction box Sensor 9-wire cable • Remote core processor with remote sensor – A remote core process with remote sensor installation separates all three components – transmitter, core processor, and sensor – all of which are installed separately. A 4-wire cable connects the transmitter [...]

Remote core processor with remote sensor installation type Figure F-6: Core processor Transmitter 4-wire cable 9-wire cable Sensor Junction box F.2 Power supply terminals and ground Power supply wiring terminals Figure F-7: A B C A. Warning flap B. Equipment ground C. Power supply wiring terminals (9 and 10) Transmitter components and installation [...]

F.3 Input/output (I/O) wiring terminals I/O wiring terminals Figure F-8: A B C A. mA/HART B. Frequency output or discrete output C. RS-485 Transmitter components and installation wiring 352 Micro Motion ® Model 2700 Transmitters with Analog Outputs[...]

Appendix G NE 53 history G.1 NE 53 history Date Version Type Change Operating in- struction 08/2000 1.x Expansion Added writing of the device tag using Modbus 3600204 A Adjustment Improved communication handling with the HART Tri-Loop product Feature Indication of outputs option board type appears on display at power-up 05/2001 2.x Expansion Added [...]

Date Version Type Change Operating in- struction The display start/stop totalizers function can be enabled or disabled Petroleum measurement application improve- ments Live zero available as display variable Increased options for fault output settings New cryogenic application temperature algo- rithms Adjustment Improved frequency output stability [...]

Date Version Type Change Operating in- struction 09/2006 5.x Expansion Discrete output assignable as a flow switch 20001715 B Discrete output fault indication configurability Discrete input support for multiple action as- signments Added support for querying the display LED sta- tus via Modbus Additional HART and Modbus commands Process comparator [...]

Date Version Type Change Operating in- struction Adjustment The following combinations are not allowed: • mA Output Fault Action = None and Digital Communications Fault Action = NAN • Frequency Output Fault Action = None and Digital Communications Fault Action = NAN Display variables set to a volume process varia- ble automatically switch betwe[...]

Index A Added Damping 105 Additional Communications Response Delay 130 address HART address 124, 129 Modbus address 130 air calibration , See calibration, density alarm menu , See display alarms alarm codes 208 configuring alarm handling 89 Status Alarm Severity configuring 90 options 91 transmitter response 157 troubleshooting 208 viewing and ackn[...]

restore factory configuration using ProLink II 22 using ProLink III 22 temperature measurement 50 volume flow measurement 29 Weights & Measures , See Weights & Measures application write-protection 21, 138 connection Field Communicator 322 ProLink II types 274 ProLink III types 298 startup connection 9 CTL 53 curve , See concentration measu[...]

polarity configuring 118 options 118 source configuring 115 options 115 display accessing menu system 253 components 251 configuring display behavior Auto Scroll 81 backlight 81 display language 77 display precision 79 display variables 78 LED Blinking 82 Update Period (refresh rate) 80 configuring security access to alarm menu 85 access to off-lin[...]

using the display 228 using the Field Communicator 233 maximum pulse width 112 polarity configuring 110 options 110 process variable configuring 108 options 109 scaling method configuring 111 Frequency = Flow 111 troubleshooting 225, 237 G gas standard volume flow measurement configuring 34 cutoff configuring 39 interaction with AO cutoff 39 effect[...]

process variable configuring 100 options 101 scaling 102 troubleshooting 224, 236 mass flow measurement configuring 23 cutoff configuring 27 effect on volume measurement 28 interaction with AO cutoff 28 flow damping 26 measurement units configuring 23 options 24 meter factor 192 troubleshooting 220 matrix , See concentration measurement application[...]

using ProLink III 54 using the Field Communicator 56 polling address , See HART address power power up 7 power supply terminals 351 power supply wiring troubleshooting 227 pressure compensation configuring using ProLink II 69 using the Field Communicator 73 overview 69 pressure measurement units options 74 primary variable (PV) 126 process measurem[...]

slave address , See Modbus address slug flow , See density measurement, slug flow Smart Meter Verification automatic execution and scheduling using ProLink II 185 using ProLink III 186 using the display 184 using the Field Communicator 186 definition 173 preparing for a test 174 requirements 174 running a test using ProLink II 177 using ProLink III[...]

unsecured , See Weights & Measures application Update Period 80 Update Rate configuring 87 effect on process measurement 88 incompatible functions 88 Upper Range Value (URV) 102 V Volume Correction Factor (VCF) 53 volume flow measurement configuring 29 cutoff configuring 33 interaction with AO cutoff 33 effect of density cutoff on 50 effect of [...]

[...]

*MMI-20019043* MMI-20019043 Rev AA 2012 Micro Motion Inc. USA Worldwide Headquarters 7070 Winchester Circle Boulder, Colorado 80301 T +1 303-527-5200 T +1 800-522-6277 F +1 303-530-8459 www.micromotion.com Micro Motion Europe Emerson Process Management Neonstraat 1 6718 WX Ede The Netherlands T +31 (0) 318 495 555 F +31 (0) 318 495 556 www.micromot[...]