Emulex DCP_link manuel d'utilisation

DCP_ link Multi-Protocol Router Advanced Configuration Guide PT1054605-00, Rev A December 1995[...]

Information contained in this document is be lieved to be accurate and reliable. However, Emulex Corporation assume s no responsibility for its use nor for any infringements of patents or other rights of third parti es which may result from its use. Emul ex Corporation reserves the right to change product specificat ions at any time wi thout notice[...]

Table of Contents Preface Product Support .................................................................................... i Audience .................................................................................... i User Guide Conventions...................................................................... ii Related Documentation .......[...]

Table of Contents ii Chapter 3 Installation and Cabling Installing the Emulex Adapter .......................................................... 3-3 Cabling Connections ......................................................................... 3-4 Factory Default Settings.................................................................... 3-4 DCP286[...]

Table of Contents iii Chapter 4 Software Installation Software Installation Procedure........................................................ 4-2 Installing to Novell NetWare version 3.12 ............................... 4-2 Installing to Novell NetWare version 4.1 ................................. 4-4 Uninstall Procedures ..........................[...]

Table of Contents iv Chapter 7 X.25 Configuration Introduction ................................................................................. 7-2 Virtual Circuit Service .............................................................. 7-3 Logical Channel Numbers ........................................................ 7-4 Diagramming Your X.25 Net[...]

Table of Contents v Appendix A Diagnostic Programs Diagnostic Platform ......................................................................... A-2 Diagnostic Operating Requirements........................................ A-2 README.DOC ....................................................................... A-2 Distribution Diskette ..............[...]

Preface Thank you for purchasing the DCP_ link Multi-Protocol Router. You have joined the Emulex family of users, who have found that buying our products guarantees available performance and bandwidth while preserving resources. We value a strong relationship with our customers and seek to continually serve your needs in the years to come. Product [...]

ii Preface User Guide Conventions Sections of text that are marked for emphasis are form atted with the following key words: Note, Important , or Caution . For example: CAUTION : Provides the user with directions to prevent a mistake from occurring. When a command is illustrated in the user’s guide, the variable choices allowed to be changed will[...]

Preface iii Related Documentation This section is designed to assist the reader in finding third party reference manuals for the support of NetWare W AN protocols and general networking architectures and principles. NetWare Guides (Included with DCP _link ) Novell NetWare MultiProtocol Router 3.0 Installation and Basic Configuration Guide Novell Ne[...]

Introduction Chapter 1 EMULEX DCP_ LINK ............................................................................................. 1-2 H ARDWARE R EQUIREMENTS ........................................................................... 1-3 S OFTWARE R EQUIREMENTS ............................................................................ 1-3[...]

1-2 Chapter 1 Emulex DCP_ link Emulex DCP_ link is a multi-protocol router including WAN connectivity software and one of the DCPx86 i/e family of communications adapters. DCP_ link is designed to work in conjunction with the Novell NetWare Branch Link and Enterprise Router, formerly known as the Novell MultiProtocol Router (MPR 3.0). This unique a[...]

Introduction 1-3 Hardware Requirements In order to successfully install the Emulex DCP_ link software, you must be running NetWare on a Novell approved hard ware platform, or you must first install the Runtime version of Novell NetWare that is shipped with DCP_ link . If you are running on a Novell approved hardware platform, you will need the foll[...]

1-4 Chapter 1 CAUTION : The system must not load any of the following modules: - extended memory managers, such as HIMEM, QEMM, or EMM386. - disk compression utilities, such as Disk Doubler. - any terminate-and-stay-resident (TSR) programs. Verify that the Novell environment meets the following criteria: • NetWare O/S version 3.12 or version 4.1 [...]

Hardware Configuration Chapter 2 FACTORY DEFAULT SETTINGS ...................................................................... 2-2 B ASE I/O A DDRESS ......................................................................................... 2-3 H OST I NTERRUPT L EVEL (IRQ S ETTING ) ........................................................ 2-5 DCP[...]

2-2 Chapter 2 DCP_ link features an 80x86 microprocessor based “intelligent” WAN adapter to provide powerful co-pro cessing capabilities. The adapter utilizes 1Mb of on-board shared memory to transfer comm ands and data to the NetWare server. DMA channels are included to support full-duplex operation. This chapter describes the factory default [...]

Hardware Configuration 2-3 NOTE: The Base I/O address and IRQ settings are the same for all adapters. Data Clock Direction, DTE, is correct for all connections except V.35. Other switch or jumper settings unique to an individual adapter type (i.e., DCP286 i -SBC, DCP386 i , or DCP486 e ) are detailed in a separate section of this chapter specific t[...]

2-4 Chapter 2 SW1 - Base I/O Address Settings Figure 2-1 SW1[...]

Hardware Configuration 2-5 Host Interrupt Level (IRQ Setting) The jumper block used to set the IRQ is unique to each adapter type. DCP286 i - J13 DCP386 i - J6 DCP486 e - J11 Refer to the specific adapter section for the location of this jumper. The available IRQ jumper settings are: / IRQ 2 Figure 2-2 Host Interrupt Level Jumper Plug Settings Use [...]

2-6 Chapter 2 DCPx86 i/e Adapter Configuration The remainder of Chapter 2 is divided into three sections according to adapter type (DCP286 i -SBC, DCP386 i , or DCP486 e ). Please refer to the section for the adapter you are installing. DCP286 i -SBC Adapter Configuration The following diagram of the DCP286 i -SBC adapter shows the location of all [...]

Hardware Configuration 2-7 Figure 2-5 shows the factory default options for the standard adapter configuration. The factory default setting, as shown, calls for jumper blocks to be in place on each jumper, thus enabling each option: Figure 2-5 Factory Default Jumper Block Placement Figure 2-6 - Jumper Block J1 Options Software Compatibility Level J[...]

2-8 Chapter 2 Control Register 4 Read Option Set Jumper J1 to enable (J1-3 to J1 -4 connected) host read access to Control Register 4. Window Group Select The DCP286 i -SBC contains memory that is shared by the host. The host software can select the size of the window that is shared using jumper J1:5-6. The factory default setting (J1-5 to J1-6 con[...]

Hardware Configuration 2-9 Setting Data Clock Direction (DTE or DCE) J7, J8, J9 and SW-3 set the synchronous data clock direction (DTE or DCE) for port 1. Jumpers J4, J5, J6 and SW2 set the synchronous data clock direction (DTE or DCE) for Port 2. Figure 2-7 Factory Default DTE Settings All Modes Except V.35 NOTE: DTE OPERATION RS422: In the RS422 [...]

2-10 Chapter 2 P O R T 2 P O R T 1 Figure 2-9 DTE Settings for the V.35 Mode P O R T 2 P O R T 1 Figure 2-10 DCE Settings for the V.35 Mode What’s Next? After configuring the DCP286 i adapter, refer to chapter 3 to:  Install the DCP286i adapter in your computer.  Attach cable.[...]

Hardware Configuration 2-11 DCP386 i Adapter Configuration The following diagram of the DCP386 i adapter shows the location of all option setting switches and jumpers: Figure 2-11 DCP386i Jumper Block Placement Jumper Settings See Figure 2-11 for the location of each jumper block. NOTE : Jumper block J6 sets the Host Interrupt Level and SW1 sets th[...]

2-12 Chapter 2 Figure 2-12 DCP386 i Factory Default Jumper Connections PC I/O Channel Check The factory default setting (J1-2 to J1-3 connected) for the DCP386 i provides an interrupt line to the PC for parity errors in the shared memory. This is the I/O Channel Check signal on the PC bus. A parity error may instead interrupt the local processor at[...]

Hardware Configuration 2-13 What’s Next? After configuring the DCP386 I adapter, refer to Daughterboard Settings section later in this chapter to:  Configure daughterboard.[...]

2-14 Chapter 2 DCP486 e Adapter Configuration The following diagram of the DCP486 e adapter shows the location of all option setting switches and jumpers: Figure 2-14 DCP486 e Jumper Block Placement J2 Jumper Settings Refer to Figure 2-14 for jumper locations. NOTE : Jumper block J11 sets the Host Interrupt Level and SW1 sets the base I/O address f[...]

Hardware Configuration 2-15 Changing this jumper plug position (J8-2 to J8-3 connected), allows window sizes of 16K, 64K or 128K. Figure 2-24 shows the Window Group Select jumper settings. 1 2 3 1 2 3 Figure 2-15 Window Group Select Jumper Positions What’s Next? After configuring the DCP486 E adapter, refer to Daughterboard Settings section to: ?[...]

2-16 Chapter 2 DCP386 i /486 e Daughterboard Settings This section provides configuration and installation instructions for the 8- port RS-232 full duplex DMA daughterboard (I.D.=BC) and the 8-port RS- 422/X.21 daughterboard. Both daughterboards are fully compatible with the DCP386 i and DCP486 e adapters. 8-Port RS-232 Daughterboard The 8-port RS-[...]

Hardware Configuration 2-17 Switch Port # DTE DCE SW1 1 1-Closed 2-Open 3-Open 1-Open 2-Closed 3-Closed 2 4-Closed 5-Open 6-Open 4-Open 5-Closed 6-Closed SW2 3 1-Closed 2-Open 3-Open 1-Open 2-Closed 3-Closed 4 4-Closed 5-Open 6-Open 4-Open 5-Closed 6-Closed SW3 5 1-Closed 2-Open 3-Open 1-Open 2-Closed 3-Closed 6 4-Closed 5-Open 6-Open 4-Open 5-Clos[...]

2-18 Chapter 2 8-Port RS-422/X.21 Daughterboard This section provides configuration and in stallation instructions for the eight port RS-422/X.21 Each serial port may be individually configured as either DTE or DCE with the aid of null-modem cables. All ports support RS-422A. Setting DTE or DCE Operation NOTE : Throughout this document, DCE refers [...]

Hardware Configuration 2-19 DTE/DCE clock selection is determin ed by the following switch settings: Switch Port # DTE DCE SW1 1 1 Closed 2-5 Open 1 Open 2-5 Closed 2 6 Closed 7-10 Open 6 Open 7-10 Closed SW2 3 1 Closed 2-5 Open 1 Open 2-5 Closed 4 6 Closed 7-10 Open 6 Open 7-10 Closed SW3 5 1 Closed 2-5 Open 1 Open 2-5 Closed 6 6 Closed 7-10 Open [...]

Installation and Cabling Chapter 3 INSTALLING THE EMULEX ADAPTER .......................................................... 3-3 CABLING CONNE CTIONS .................................................................................. 3-4 FACTORY DEFAULT SETTINGS ...................................................................... 3-4 DCP286 I -SBC [...]

3-2 Chapter 3 DCP386 I/ 486 E DAUGHTERBOARD CA BLING ............................................. 3-20 RS-232 C ABLING .......................................................................................... 3-20 RS-232 Standard Cable......................................................................... 3-21 RS-232 Null-Modem Cable (Crossover[...]

Hardware Installation 3-3 This section describes the procedure for installing the DCP286 i -SBC, the DCP386 i , and the DCP486 e WAN adapter in your server/router. Brief troubleshooting procedures are also provided. Installing the Emulex Adapter To install the adapter perform these steps: 1) Turn off power to the system unit. Remove the power cord [...]

3-4 Chapter 3 Cabling Connections Cabling specifications for each adapter type (DCP286 i -SBC, DCP386 i and DCP486 e) are found in the following section. Cabling differences will be noticed when connecting a DTE port to a DCE device (normally a straight through cable), and when connecting a DTE port to a DTE device (normally a null modem cable). Fa[...]

Hardware Installation 3-5 − RS232 8-port breakout cable for DCP386 i and DCP486 e adapter (80-pin), Emulex part no. PA1011236-01. RS-422/X.21 Cabling For RS-422/X.21 conversion, you will n eed a set of eight X.21 conversion cables at the end of the 8-port breakout cable. These are available from Emulex Sales Support. − RS422 8-port breakout cab[...]

3-6 Chapter 3 Optional Cable Drawings Loopback Plug Options A loopback connector must be used when running external loopback tests on the DCP286 i/ 386 i/ 486 e Platform Diagnostics. R-S232/EIA-530 Loopback Plug (DB25F) Loopback plug signals for the female 25-pin connector. This loopback plug will work for RS232, RS422/EIA530, RS423, and RS485 adap[...]

Hardware Installation 3-7 V.35 Loopback Plug Winchester Male P S R T V AA V X C D H E F TDA TDB RDA RDB TCA TCB RCA RCB RTS CTS DTR DSR CD Figure 3-2 (Not Supplied by Emulex)[...]

3-8 Chapter 3 X.21 Loopback Plug DBI5F 2 9 4 11 3 10 5 12 7 14 6 13 TA TB RA RB CA CB 1A 1B SA SB Figure 3-3 (Not Supplied by Emulex)[...]

Hardware Installation 3-9 DCP286 i -SBC Adapter Cables RS-232 Cable Assembly TDA RDA RTSA CTSA DSRA CDA RCA TCA DTRA SG 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL J1 MICRO-D25 FEMALE P1 DB25 MALE TDB RDB RTSB CTSB DSRB CDB RCB TCB DTRB RGND MODE0 MO[...]

3-10 Chapter 3 RS-422/530 Cable Assembly TDA TDB RDA RDB RTSA RTSB CTSA CTSB DSWRA DSRB CDA CDB RCB RCA TCB TCA DTRA DTRB SG 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL J1 MICRO-D25 FEMALE P1 DB25 MALE RTSB CTSB DSRB CDB DTRB RGND MODE0 MODE1 MODE2 M[...]

Hardware Installation 3-11 RS-423 Cable Assembly TDA RDA RTSA CTSA DSRA CDA RCA TCA DTRA SG RGND TBD RDB RTSB CTSB DSRB CDB RCB TCB DTRB RGND MODE0 MODE1 MODE2 MODE3 Figure 3-3 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL J1 MICRO-D25 FEMALE P1 DB25 M[...]

3-12 Chapter 3 RS-485 Cable Assembly TDA TDB RDA RDB RTSA RTSB CTSA CTSB DSRA DSRB CDA CDB RCB RCA TCB TCA DTRA DTRB SG 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL J1 MICRO-D25 FEMALE P1 DB25 MALE RTSB CTSB DSRB CDB DTRB RGND MODE0 MODE1 MODE2 MODE3 [...]

Hardware Installation 3-13 V.35 Cable Assembly TDA TDB RDA RDB RTSA CTSA DSRA CDA RCB RCA TCB TCA DTRA SG A P S R T C D E F X V AA Y H B SHELL 1 2 14 3 16 4 19 5 13 6 22 8 10 9 17 12 15 20 23 7 11 18 21 24 25 SHELL J1 MICRO-D25 FEMALE J2 V.35 FEMALE RTSB CTSB DSRB CDB DTRB RGND MODE0 MODE1 MODE2 MODE3 Figure 3-8 Emulex Part #PT1011213-01[...]

3-14 Chapter 3 X.21 Cable Assembly Figure 3-9 Emulex Part #PT1011221-01[...]

Hardware Installation 3-15 RS-232 Standard Cable TDA RDA RTSA CTSA DSRA SG CDA TCA RCA DTRA 1 2 3 4 5 6 7 8 15 17 20 1 2 3 4 5 6 7 8 15 17 20 DB25 FEMALE DCP PORT MODEM OR OTHER DC E FG Figure 3-10 (Not Supplied by Emulex)[...]

3-16 Chapter 3 RS-232 Null-Modem Cable (Crossover) TRANSMIT DATA RECEIVE DATA REQUEST TO SEND CLEAR TO SEND DATA SET READY SIGNAL GROUND DATA CARRIER DETECT TRANSMIT CLOCK RECEIVE CLOCK DATA TERMINAL READY 1 2 3 4 5 6 7 8 15 17 20 1 2 3 4 5 6 7 8 15 17 20 TRANSMIT DATA RECEIVE DATA REQUEST TO SEND CLEAR TO SEND DATA SET READY SIGNAL GROUND DATA CAR[...]

Hardware Installation 3-17 RS-423/RS-485 Null Modem Cable Figure 3-12 (Not Supplied by Emulex)[...]

3-18 Chapter 3 V.35 Null Modem Cable FG RTS CTS TDA TDB RDA RDB RCA RCB TCA TCB ETC-A ETC-B DSR CD DTR SG SHELL A C D P S R T V X Y AA U W E F H B SHELL DCP PORT V.35 MALE TERMINAL OR OR OTHER DTE V.35 FG RTS CTS TDA TDB RDA RDB RCA RCB TCA TCB ETC-A ETC-B DSR CD DTR SG A C D P S R T V X Y AA U W E F H B Figure 3-13 (Not Supplied by Emulex)[...]

Hardware Installation 3-19 X.21 Null Modem Cable SHIELD Figure 3-14 (Not Supplied by Emulex)[...]

3-20 Chapter 3 DCP386 i/ 486 e Daughterboard Cabling This section discusses cable connections between the 8-port daughterboard on the DCP386 i and DCP486 e adapters and external devices. RS-232 Cabling The serial ports on the 8-port daughterboard are connected to external devices via an 8-port breakout cable. Each port provides a standard 25-pin ma[...]

Hardware Installation 3-21 RS-232 Standard Cable TDA RDA RTSA CTSA DSRA SG CDA TCA RCA DTRA 1 2 3 4 5 6 7 8 15 17 20 1 2 3 4 5 6 7 8 15 17 20 DB25 FEMALE DCP PORT MODEM OR OTHER DC E FG Figure 3-15 (Not Supplied by Emulex)[...]

3-22 Chapter 3 RS-232 Null-Modem Cable (Crossover) TRANSMIT DATA RECEIVE DATA REQUEST TO SEND CLEAR TO SEND DATA SET READY SIGNAL GROUND DATA CARRIER DETECT TRANSMIT CLOCK RECEIVE CLOCK DATA TERMINAL READY 1 2 3 4 5 6 7 8 15 17 20 1 2 3 4 5 6 7 8 15 17 20 TRANSMIT DATA RECEIVE DATA REQUEST TO SEND CLEAR TO SEND DATA SET READY SIGNAL GROUND DATA CAR[...]

Hardware Installation 3-23 RS-422/X.21 Cabling External devices are connected to the daughterboards on the DCP386 i and DCP486 e adapters via a breakout cable. This cable provides eight short cables, each with a DB25M (male) connector. The breakout cable is connected to the daughterboard via a 100-pin connector. All connections should be made using[...]

3-24 Chapter 3 RS-422 Standard Cable MODEM OR DCP PORT DCE 1 z CHASSIS GROUND z 1 2 z TRA NS MIT D ATA (A ) z 2 3 z RECEIVE DA TA (A) z 3 4 z REQUEST T O SEND ( A) z 4 5 z CLEAR TO SE N D (A) z 5 7 z SIGNAL GROUND z 7 9 z RECEI V E CLOCK (B ) z 9 12 z TRANSMIT CLOCK (B) z 12 13 z CLEAR TO SEND (B) z 13 14 z TRA NS MIT D ATA (B) z 14 15 z TRANSMIT C[...]

Hardware Installation 3-25 X.21 Adapter Cable DB25 MALE MALE J1 P1 SHLD SHLD 1 zz 1 2 z TDA z 2 14 z TDB z 9 3 z RDA z 4 16 z RDB z 11 15 z TCA 12 z TCB 17 z RCA SA z 6 9 z RCB z 13 4 z RTSA z 3 19 z RTSB z 10 6 z D SRA IA z 5 22 z DSRB z 12 8 z DCDA z 8 10 z DCDB 5 z CTSA 13 z CTSB 7 z GND Figure 3-19 Emulex Part #PT1011204-01[...]

3-26 Chapter 3 RS-422 Null-Modem Cable DCP PORT 1 z CHASSIS G ROUND z 1 2 z TRA NSMI T D AT A (A ) T RANSMI T DAT A (A ) z 2 3 z RECEI VE DA TA (A ) RECEI VE D ATA (A ) z 3 4 z REQU EST T O SEND (A) REQ UEST TO S END (A ) z 4 5 z CL EAR T O SEND (A) CLE AR T O SEND (A) z 5 7 z SIG NAL GROUND z 7 9 z RECEI VE CL OCK (B) RECE IVE C LOCK (B) z 9 12 z [...]

Hardware Installation 3-27 Troubleshooting If you experience a problem immediately after installing the adapter, check these areas: 1) Is the device cable the correct type? Some asynchronous cables do not have enough wires to support the additional signals required for synchronous communications. 2) Is the board securely seated in the system unit? [...]

Software Installation Chapter 4 SOFTWARE INSTALLATI ON PROCEDURE .................................................. 4-2 Installing to Novell NetW are version 3.12 ................................................................................4-2 Installing to Novell NetW are version 4.1 .............................................................[...]

4-2 Chapter 4 Software Installation Procedure This section describes the installation procedure for the Emulex DCP_ link software. The software can be installed either locally on a single server or remotely on several servers. If NetWare MPR 3.0 software has been successfully loaded on your sy stem, please continue with installation of the Emulex s[...]

Software Installation 4-3 After a short delay, the Installation Options menu appears. Figure 4-3 Installation Options Menu Select Install on Local Server Only , then press <Enter>. The INSTALL program copies several files from the INSTALL diskette to a local directory. 5) When the source files have been copied, the following message is displa[...]

4-4 Chapter 4 Installing to Novell NetWare version 4.1 1) At the NetWare server system console prompt, type > Load Install <Enter> The Installation Options menu appears. Figure 4-4 The Installation Options Menu (v.4.1) 2) Select Product Options , then press <Enter>. The Other Installation Actions menu is displayed. Figure 4-5 Other I[...]

Software Installation 4-5 Note : If you inserted the INSTALL diskette into drive B: on a local server, press <F3>, repla ce A: with B:, then press <Enter>. After a short delay, the Installation Options menu appears. Figure 4-6 The Installation Options Menu 3) Install on Local Server Only is highlighted; press <Enter>. The INSTAL[...]

4-6 Chapter 4 9) Highlight EMULEX WAN for NetWare and press <Enter> to access the Internetworking Configuration menu. 10) You are now ready to configure the Emulex DCP_ link adapter and create specific WAN links. Please turn to Chapter 5, Software Configuration to continue. Uninstall Procedures If it becomes necessary to unload Emulex softwar[...]

Software Installation 4-7 All protocol Binds and WAN Call Destinations will be deleted automatically. Return to the console server prompt when finished. 5) At the console server prompt, type: > Load Install <Enter>. The Installation Options menu will be displayed: Figure 4-9. The Installation Options Menu 6) Select Product Options and dele[...]

4-8 Chapter 4 Uninstall using NetWare version 4.1 1) At the console server prompt, type: > LOAD INETCFG <Enter>. The Internetworking Configuration menu will be displayed: 2) Select Netw ork Interfaces. Using the <Del> key, deconfigure all interfaces associated with the Emulex adapter. 3) Press <Esc> to return to the Internetwor[...]

Software Installation 4-9 6) Select Driver Options from the Installation Options m enu, select Configure the Netw ork Drivers and press <Enter>. 7) Using arrow keys, highlight Deselect a Selected Driver and press <Enter>. 8) Use the arrow keys to select the EMXMLID driver and press <Enter> or <Delete> to remove it. 9) Return[...]

Software Configuration Chapter 5 INETCFG ................................................................................................................... 5-2 INETCFG M ENUS ........................................................................................................ 5-2 U SING C ONTEXT -S ENSITIVE H ELP ...............................[...]

5-2 Chapter 5 INETCFG The Internetworking Configuration utility (INETCFG) is a menu- driven utility used to configure the Emulex software. You can run INETCFG while the router or server is operating. Each time the utility is used, it reads the existing AUTOEXEC.NCF file and optionally transfers the LOAD and BIND commands to a configuration file tha[...]

Software Configuration 5-3 Boards - Determines which LAN and WAN boards are used in the server or router. This option allows you to add new boards, modify the hardware parameters associated with the boards, enable or disable configured boards, or delete boards. Netw ork Interfaces - Allows you to configure media-specific Data-Link layer parameters [...]

5-4 Chapter 5 <Esc> key exits the current configuration window or help screen and returns you to the previous screen. Press <Esc> from the main screen to exit the program and save your configuration changes. <Enter> key allows you to view a lis t of configuration options or modify the selected option’s configuration. <Ins>[...]

Software Configuration 5-5 Configuring with INETCFG Important: You must use INETCFG to configure the Emulex software and hardware you have installed in your server/router. If INETCFG is not running, complete the following steps to load it: 1) At the server prompt, type > LOAD INETCFG <Enter> The Internetw orking Configuration main menu is [...]

5-6 Chapter 5 Figure 5-2 3) Press <Ins> to display the list of available drivers. Figure 5-3 4) From the list, select the EMXMLID driver for the Em ulex DCPx86 i/e adapter installed in your system. Note: Call Emulex technical support if the driver is not listed. 5) Enter a name in the Board Name field up to 10 alphanumeric characters and pres[...]

Software Configuration 5-7 Figure 5-4 6) Review the default values in the Board Configuration menu, and m NOTE: iew akes changes as needed. Refer to Chapter 2 of this guide to rev the default configuration information used while installing the Emulex DCPx86i/e adapter. For non-standard installations, please refer to the Emulex DCP_link Advanced Con[...]

5-8 Chapter 5 Use the <Tab> key to toggle between Enabled and Disabled as needed . 9) Press <Esc> to return to the Internetworking Configuration Wha he DCP_ link software, refer to anual for: Frame Relay Configuration  X.25 Configuration menu. t’s Next? After installing and configuring t Chapters 6 and 7 of this m [...]

Frame Relay Configuration Chapter 6 INTRODUCTION ................................................................................................................ 6-2 Frame Relay Networks ........................................................................................................... ...6-2 Frame Relay Parameters .........................[...]

6-2 Chapter 6 Introduction Emulex Frame Relay software is a streamlined, connection-oriented fram e- mode data service based on frame-switching /relaying technology--the process of quickly transporting HDLC (High-level Data Link Control) frames through a network. This software is based on Frame Relay , a WAN telecom munications protocol standard sp[...]

Frame Relay Configuration 6-3 Emulex Frame Relay encapsulates data frames and routes them through the Frame Relay network based on the Data-Link Connection Identifier (DLCI), which identifies the local permanent virtual circuit (PVC) end point of the router. DLCIs are defined through the configuration process or teamed through the Emulex Frame Rela[...]

6-4 Chapter 6 The Frame Relay network switch monitors the access rate and size of data frames transferred through the mesh network. The data throughput CIR is guaranteed by the network, but allows for excess bursts (Be) of data not to exceed the access rate (AR) of the connection. The committed burst size (Bc) sets the maximum amount of data that t[...]

Frame Relay Configuration 6-5 communicate with three rem ote sites using a minimum of 32 Kbps sustained bandwidth, the physical interface must be able to support at least 3 x 32 Kbps = 96 Kbps. You shoul d also consider traffic pattern characteristics (bursty or sustaine d) when specifying interface speed. Encoding Option - Corresponds to the encod[...]

6-6 Chapter 6 Configuring the Network Interface To configure network interface parameters for Emulex Fram e Relay software, load the INETCFG Internetworking Configuration menu: 1) At the server prompt, type > LOAD INETCFG <Enter> The Internetworking Configuration menu is displayed. Figure 6-1 Internetworking Configuration 2) Select Netw or[...]

Frame Relay Configuration 6-7 4) Select Frame Relay (EMX F Relay) from the Available Media, then press <Enter>. The DCP_link Frame Relay Network lnterface Configuration menu is displayed. 5) Press <Enter> to display a list of the Emulex DCPx86 i/e adapters that are installed. 6) Select the adapter you wish to configure and press <Ent[...]

6-8 Chapter 6 NOTE : The User Data Size should be smaller than the absolute frame size accommodated by the network, i.e., less than the Maximum Physical Packet Receive Size configured in the STARTUP.NCF file. Verify that all destinations support the same Maximum Physical Packet Receive Size. Send Queue Limit specifies the maximum number of outbound[...]

Frame Relay Configuration 6-9 Full Status Enquiry Counter specifies the number of standard status enquiries to exchange before issuing a full status inquiry from the network. The value ranges from 1 to 255 with a factory default of 6 enquiries. A full status enquiry response from the network updates the Frame Relay network and link information tabl[...]

6-10 Chapter 6 Configuring WAN Call Directory The WAN Call Directory is a list of WAN Call Destination configurations to use for each virtual circuit. You must create at least one WAN Call Destination configuration for each destination. WAN Call Destination configurations contain parameters to be applied by Emulex Fram e Relay software when establi[...]

Frame Relay Configuration 6-11 NOTE : If a WAN Call Destination has not been configured, the list will be empty (as pictured above). 3) Press <Ins> to configure a new WAN Call Destination. The prompt New Call Destination Name allows y ou to enter a name of up to 47 alphanumeric characters for the new WAN Call Destination. Figure 6-5 Configure[...]

6-12 Chapter 6 NOTE : If you have not configured any Network Interfaces before attempting to configure a WAN Call Destination, you receive this message: WAN network interfaces must be configured before WAN Call Destinations may be created. 5) Select EMX F Relay as the wide area m edium. The Frame Relay Call Destination Configuration menu is display[...]

Frame Relay Configuration 6-13 Network Protocols and Bindings The following sections outline the step s necessary to configure the Network Protocols and Bindings so the interfaces can be used with the LAN and WAN connections just established. Configuration of protocols and bindings must be completed prior to using the Emulex software. Configuring P[...]

6-14 Chapter 6 NOTE: Most installations can function properly with the factory default parameters. For non-standard applications, refer to the Novell NetWare MPR 3.0 Advanced Configuration and Management Guide . Binding Network Protocols to a WAN Interface After adding and configuring the desired protocols outlined above, complete the following ste[...]

Frame Relay Configuration 6-15 4) Select the desired protocol (e.g., IPX), then press <Enter>. 5) From the Network Interface menu, select a configured WAN interface port, then press <Enter> to bind the protocol to that port. A new window displays the parameters for binding the protocol you have chosen to the selected WAN interface. Figu[...]

6-16 Chapter 6 Figure 6-14 Configured Wan Call Destinations NOTE: If no permanent WAN Call Destinations have been defined for this interface, an error message will be displayed. 9) Highlight the desired WAN Call Destination, then press <Enter>. Press <Esc> until you are prompted to save IPX Bind Parameters. Answer Yes to save and exit. [...]

X.25 Configuration Chapter 7 INTRODUCTION ................................................................................................................ 7-2 Virtual Circu it Service ........................................................................................................ .......7-3 Logical Channe l Numbers .........................[...]

7-2 Chapter 7 Introduction Emulex X.25 software operates in a NetWare server or NetWare router/bridge PC environment and provides services for NetWare products and other applications (including i ndependent develope r applications) requiring wide area connectivity Emulex X.25 uses the 1984 CCITT X.25 Recomm endation, which defines the interaction b[...]

X.25 Configuration 7-3 Virtual Circuit Service X.25 uses two mechanisms, providing a logical path between end points, called virtual circuits. A virtual ci rcuit provides a connection-oriented service, similar to that of circuit switching but with the following exceptions: • Limited to a connection between two end points. • Economical statistic[...]

7-4 Chapter 7 Logical channels differentiate the virt ual circuits supported by the packet level. Each packet is associated with a logical channel which is mapped to the appropriate destination of the virt ual circuit. Multiple connections are provided simultaneously by multiplexing virtual circuits over the access line. This enables a more effecti[...]

X.25 Configuration 7-5 Diagramming Your X.25 Network To ensure that all connections to the X.25 network are properly diagrammed, complete these step: 1) Diagram the existing X.25 network showing all router access points and mark the X.25 addresses. 2) Draw each type of connection from the local router to its corresponding partner. For PVC-type conn[...]

7-6 Chapter 7 Maximum Frame Size (Nl) - Determines the maximum frame size (in octets) allowed to be received on the li nk. It is automatically configured from the packet size and maxim um packet size information. Retry Count (N2) - Determines the m aximum number of tim es a frame should be retransmitted because of the expiration of the Retry Timer [...]

X.25 Configuration 7-7 When establishing a connection to an X.25 network, you must set this parameter to DTE (the default valu e) if you are connecting to a X.25 service provider. Default Inbound/Outbound Packet Size - The Inbound Packet uses the default packet size for a inbound call unless another packet size is specified. Set this value to corre[...]

7-8 Chapter 7 T25 (Data Packet Retransmission Timer) - Specifies the amount of time, in seconds, that the DTE waits for the appropriate acknowledgment after transmitting a data packet. If the T25 timer expires, the packet layer resets the virtual circuit. T26 (Interrupt Timer) - Specifies the amount of time, in seconds, that the DTE waits when an I[...]

X.25 Configuration 7-9 Tw o Way SVC, Number of LCNs - Determines the lowest LCN that can be used for two-way SVCs. This number must agree with your network subscription. Outbound, Low est LCN - Determines the lowest LCN that can be used for outgoing logical channels for SVCs. The value must be greater than or equal to the Lowest two-way SVC LCNs va[...]

7-10 Chapter 7 Reverse Charging Calls - Offers the equivalent of a collect call. It is allowed on a per-call basis and is speci fied in the Call Request packet by the calling DTE. Closed User Group (CUG ) - Allows the configuration of one or more virtual private networks within a larger public network. A user may gather a number of DTEs into a sing[...]

X.25 Configuration 7-11 1) At the server prompt, type > LOAD INETCFG <Enter> The Internetworking Configuration menu is displayed. Figure 7-1 Internetworking Configuration 2) S elect Netw ork Interfaces and press <Enter>. The Network Interface window is displayed. Figure 7-2 Network Interfaces 3) Select an unconfigured interface (port[...]

7-12 Chapter 7 Figure 7-3 Network Interface Configuration NOTE : Network interfaces assigned to a group may require the same configuration for physical and link parameters. For example baud rate, DTE/DCE...etc 5) Card Type: Select the Emulex adapter type if not already displayed. 6) Interface Options : Press <Enter> to select Interface Option[...]

X.25 Configuration 7-13 10) Press <Enter> to select an Interface Group. Select a group from the list or press <Ins> to create a new Interface group. Modifying/Creating a Profile 1) Press <Enter> and select the standard profile for you X.25 service provider. All X.25 installations must have detailed port profiles defined. Press <[...]

7-14 Chapter 7 Lowest PVC LCN Lowest Two-Way SVC LCN Number PVC LCNs Number Two-Way SVC LCNs Lowest Inbound SVC LCN Lowest Outbound SVC LCN Number Inbound LCNs Number Outbound LCNs User Facility Setup Parameters: Flow Control Negotiation Closed User Group Maximum Packet Size Bilateral CUG Maximum Window Size D-Bit Authorization Incoming Refuse Char[...]

X.25 Configuration 7-15 Local DTE Address 1) Enter the access address provided by your local X.25 network service provider. NOTE : You can leave the configuration at this point by accepting the default values for the remaining parameters. To save this configuration and return to the Internetworking Configuration menu, press <Esc>, select Yes [...]

7-16 Chapter 7 Inbound Authentication - Toggle between Enabled or Disabled. Restricts incoming calls to authentication. The originator (server ID and address) of each call coming in on the X.25 link is first checked against the Authentication Database before it is given access to the server. Only those calls in the table are accepted. All other cal[...]

X.25 Configuration 7-17 Configuring the WAN Call Directory The WAN Call Directory is a list of WAN Call Destination configurations you want to use for each virtual circuit. You must create at least one WAN Call Destination configuration for each desired destination. WAN Call Destination configurations contain para meters to be applied by Emulex X.2[...]

7-18 Chapter 7 2) The Configured Wan Call Destin ations window is displayed: Figure 7-7 Configured Wan Call Destinations If no WAN Call Destinations have b een configured, the list will be blank. 3) Press <Ins> to configure a new WAN Call Destination for X.25. 4) Enter a name for the new WAN Call Destination, then press <Enter>. NOTE : [...]

X.25 Configuration 7-19 6) In the Call Type field, accept the default value Permanent or press <Enter> to select On-Demand from the pop-up list. Reminder : You must configure the X.25 Authentication Options in the X.25 Profile if you select “on- demand” as the Call Type. On-Demand calls are established only when needed. The connections ar[...]

7-20 Chapter 7 9) For SVC, enter the DTE Address in the Destination DTE Address field. For PVC, enter the PVC number (which must be configured in the X.25 Profile). Press <Enter> for a list of configured PVC numbers. NOTE: PVC Numbers may only be configured provided the Wan Call Circuit type is Permanent and the X.25 profile for that interfac[...]

X.25 Configuration 7-21 This parameter specifies the maxim um delay between attempts to establish a connection (the retry interval). The delay is set initially to 8 seconds and increases exponentially until the maximum retry interval is reached. The range of time intervals is 00:00:00 to 23:59:59 (hh:mm :ss). For permanent calls, the default value [...]

7-22 Chapter 7 Expert Call Configuration 1) If Circuit Type is Switched Virtual Circuit, press <Enter> to view or modify the Expert Call Configuration parameters. Figure 8-9 X.25 Expert Call Configuration The X.25 Expert Call Configuration window is displayed. The parameters in this window are applicable only to SVC’s. The Call Destination [...]

X.25 Configuration 7-23 10) In the Inbound Authentication Update field, accept the default value, Enabled, or press <Enter> to select Disabled. 11) Press <Esc>; if prompted, select Yes to save your changes, then press <Enter>. The WAN Call Destination you just configured appears in the list of configured WAN Call Destinations. To [...]

7-24 Chapter 7 Network Protocol and Binding The following sections outline the step s necessary to configure the Network Protocols and Bindings so the interfaces can be used with the LAN and WAN connections just established. Configuration of protocols and bindings must be completed prior to using the Emulex software. Configuring Protocol Parameters[...]

X.25 Configuration 7-25 NOTE: Most installations can function properly with the factory default parameters. For non-standard applications, refer to the Novell NetWare MPR 3.0 Advanced Configuration and Management Guide . Binding Network Protocols to a WAN Interface After adding and configuring the desired protocols outlined above, complete the foll[...]

7-26 Chapter 7 4) Select the desired protocol (e.g., IPX), then press <Enter>. 5) From the Network Interface menu, select a configured WAN interface port, then press <Enter> to bind the protocol to that port. A new window displays the parameters for binding the protocol you have chosen to the selected WAN interface. Figure 7-13 Binding [...]

X.25 Configuration 7-27 Figure 7-15 Configured Wan Call Destinations NOTE: If no permanent WAN Call Destinations have been defined for this interface, an error message will be displayed. 9) Highlight the desired WAN Call Destination, then press <Enter>. Press <Esc> until you are prompted to save IPX Bind Parameters. Answer Yes to save a[...]

Contacting Emulex Chapter 8 TECHNICAL ASSISTANCE .............................................................................................. 8-2 P RIOR TO Y OUR C ALL ................................................................................................... 8-2 P LACING THE C ALL .........................................................[...]

8-2 Chapter 8 Technical Assistance If you experience problems and cannot resolve them, contact Emulex Technical Support. Prior to Your Call Prior to calling Technical Support, gather the following information: 1) Type of host, operating system, and release level (for example, SparcStation II with SunOS 4.1.1). 2) Network operating system (Novell, T[...]

Contacting Emulex 8-3 Domestic Emulex (USA) Technical Support 3535 Harbor Boulevard Costa Mesa, CA 92626 Telephone: (800) 854-7112, ext. 8270 or (714) 662-5600, ext 8270 FAX: (714) 513-8269 BBS (714) 662-1445 (24 hr) EmuFax (714) 513-8276 or (714) 513-8277 ftp: ftp.emulex.com (24 hr) Internet: tech_support@emulex.com (24 hr) Support Services (714) [...]

8-4 Chapter 8 24 - Hour Support Technical Support within the USA is available 24 hours a day. After normal working hours, dial one of the following numbers: Telephone: (800) 854-7112, ext. 8270 or (714) 662-5600, ext 8270 Automatic Call Distribution: (714) 513-8270 (6:00 a.m. - 5:00 p.m .) The after-hours answering service asks for a name, company [...]

Contacting Emulex 8-5 3) Set the software to dial one of these domestic or European numbers: − Domestic: (714) 662-1445 Auto rollover will be activated if the number is busy. If that modem becomes inactive, dial one of these numbers: (714) 662-1582 (714) 662-1630 − European: (44) 1-734 773298 The following file areas are available on the BBS: F[...]

8-6 Chapter 8 Internet The Emulex BBS has Internet access via Anonymous ftp, an Internet service that allows connection to a remote host without being a registered user on the host. 1) Userid: Anonymous The IP address for the BBS is: − standard-name ftp.emulex.com − numeric-version 138.239.224.1 2) At the main directory, view the readme file fo[...]

Contacting Emulex 8-7 NOTE : The file EMULEX.LST in the EVERYONE directory describes the files locate d in each directory. EmuFax EmuFax is an automated docum ent retrieval system that sends Emulex documents or catalogs to your fax machine. To use EmuFax, dial: (714) 513-8276 or (714) 513-8277 When prompted during the EmuFax recording, enter the do[...]

Diagnostic Programs Appendix A DIAGNOSTIC PLATFORM ............................................................................................. A-2 Diagnostic Operating Requirement s ......................................................................................... A-2 README.DO C ............................................................[...]

A-2 Appendix A This section describes the operation of the diagnostic program. This program tests all functions of the DCPx86 i/e , including on-board memory and registers, host memory, interrupts to and from the adapter, and the microprocessor. For DCP286 i -SBC and DCP486 e adapters, use the following DIAGNOSTIC PLATFORM. For the DCP386 i adapter[...]

Diagnostic Programs A-3 Distribution Diskette The diagnostic diskette contains these files: • platform.exe • localx86.bin • help.txt • help.idx • readme.doc • @6141.ADF • !emu0000.cfg • !emu0008.cfg Check the diskette to make sure a ll these files are present, then make a backup copy of the diagnostic diskette for regular use. If yo[...]

A-4 Appendix A 1) Boot the system under DOS and insert the Emulex diagnostic diskette into drive A. 2) Create a subdirectory on the hard disk of your choice then copy the diagnostics to that sub directory. 3) At the DOS prompt, type > Platform The Diagnostic Platform Main Menu appears. You are now ready to configure the Platform and run the desi[...]

Diagnostic Programs A-5 • Hardw are - This submenu displays the test configuration of the board highlighted in the Main Menu and allows you to change various parameters such as “Window Size,” “Window Address,” and “Interrupt Level”. In the submenu use the arrow keys to highlight the item you wish to change and the “Change Selecti on[...]

A-6 Appendix A Selecting the On Error option allows you to determine what action will be taken when an error occurs on th e selected adapter. Error actions can be set for each adapter independently. NOTE : You must run host test #9 Downloaded Diagnostics in order to run the local tests. This test is loaded to run automatically in the default set up[...]

Diagnostic Programs A-7 Exit - In the Main Menu, selecting the Exit option exits the Platform and returns control the PC to DOS. Using DCPDIAG3 for the DCP386 i This section describes the operation of the diagnostic program supplied with the DCP386 i/e . The diagnostics test all functions of the DCP386 i/e , including on-board memory and registers,[...]

A-8 Appendix A • options.386 • dmadcp.asm • dmapc.asm • dma.equ • dcp286d.equ • mac.equ • scc.equ • assem.bat • build.bat • dmatest.bat • dmatest.doc Check the diskette to make sure all these files are present. After you have done this, make a backup copy of the di agnostic diskette for regular use. If running the diagnostics [...]

Diagnostic Programs A-9 NOTE : A loopback connector must be used when running external loopback tests. Refer to Chapter 3 Alternatively you may copy the diagnostics to your hard drive and load and run from the hard drive. 1) Boot the system under DOS and insert the Emulex diagnostic diskette into drive A. 2) Create a subdirectory on the hard disk o[...]