Français dropdown-ico

Generac 40kW LP manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Generac 40kW LP. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Generac 40kW LP ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Generac 40kW LP décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Generac 40kW LP devrait contenir:
- informations sur les caractéristiques techniques du dispositif Generac 40kW LP
- nom du fabricant et année de fabrication Generac 40kW LP
- instructions d'utilisation, de réglage et d’entretien de l'équipement Generac 40kW LP
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Generac 40kW LP ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Generac 40kW LP et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Generac en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Generac 40kW LP, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Generac 40kW LP, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Generac 40kW LP. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Owner’ s Man ual ONL Y QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD A TTEMPT INST ALLA TION!! This manual should remain with the unit. Liquid-cooled, Prepac kaged Standb y Generators Model No: 005012-0 37kW NG, 40kW LP[...]

  • Page 2

    Generac ® Pow er Systems, Inc. I NTRODUCTION Thank you for purchasing this model of the QuietSource standby generator set product line by Generac P ower Systems. Every effort was expended to make sure that the information and instructions in this manual are both accurate and current at the time the manual was writ- ten. However , the manufacturer [...]

  • Page 3

    T able of Contents QUIET SOURCE ™ 40kW Liquid-cooled Generators Generac ® Pow er Systems, Inc. 1 INTRODUCTION ................................................ IFC Read this Manual Thoroughly ......................................IFC Operation and Maintenance ........................................IFC How to Obtain Service ......................[...]

  • Page 4

    2 Generac ® Pow er Systems, Inc. Study these SAFETY RULES carefully before installing, operating or servicing this equipment. Become familiar with this Owner’s Manual and with the unit. The genera- tor can operate safely , efficiently and reliably only if it is properly installed, operated and maintained. Many acci- dents are caused by failing t[...]

  • Page 5

    Generac ® Pow er Systems, Inc. 3 • Inspect the generator regularly , and promptly repair or replace all worn, damaged or defective parts using only factory-approved parts. • Before performing any maintenance on the generator , disconnect its battery cables to prevent accidental start -up. Disconnect the cable from the battery post indicated by[...]

  • Page 6

    4 Generac ® Pow er Systems, Inc. 1.1 GEN ER A T OR This equipment is a liquid- cooled, engine - driven gen- erator set. The generator is designed to supply elec- trical power that operates critical electrical loads during utility power failure. The unit has been facto- ry-installed in a weather resistant, all metal enclosure and is intended for ou[...]

  • Page 7

    Generac ® Pow er Systems, Inc. 5 1.6 GEN ER A T OR F U EL SY S TEM The unit has been factory tested and adjusted using a natural gas fuel system. If propane (LP) gas is neces- sary , refer to Section 1.12 for conversion instructions. F uel pressure for a natural gas set up should be five inches to 14 inches of water column (0.18 to 0.5 psi) at all[...]

  • Page 8

    6 Generac ® Pow er Systems, Inc. Figure 1.6 - Low Coolant Level Sensor 1.7 .4 O VERSPEED SH UTDOWN The engine control board receives AC frequency sig- nals from an engine run winding in the alternator . Should AC frequency exceed about 72 Hertz for three seconds or 75 Hertz instantaneously , the engine shuts down and the overspeed LED turns on. Sh[...]

  • Page 9

    1.1 0 SP ECIF ICA TIONS 1.1 0.1 GEN ER A T OR SP ECIF ICA TIONS 1.1 0.2 ENGI N E SP E CI F ICA TIONS Make ................................................................................Chrysler Displacement ..................................................................3.9 liters Cylinder Arrangement ............................................[...]

  • Page 10

    8 Generac ® Pow er Systems, Inc. NOTE: P ort 1 is for NG only and P ort 2 is for LP vapor only . No provision for dual fuel has been made. Serious injury or damage may occur if not con- figured pr operly . Please consult an authorized Generac Service Dealer with any questions. 1.1 3 T ORQU E SP ECIF ICA TIONS Tighten the bolts from the middle out,[...]

  • Page 11

    Generac ® Pow er Systems, Inc. 9 Only qualified, competent installation contractors or electricians thoroughly familiar with applicable codes, standards and regulations should install this standby electric power system. The installation must comply strictly with all codes, standards and regula- tions pertaining to the installation. After the syste[...]

  • Page 12

    10 Generac ® Pow er Systems, Inc. Figure 2.1 – Basic Standby Electric System 2.5 EM ERGENCY CI RCU IT IS OL A TION M E THOD This prevents overloading the generator by keeping electrical loads below the wattage/amperage capacity of the generator . If the generator is powering only crit- ical loads, within the wattage/amperage capacity , dur- ing [...]

  • Page 13

    Generac ® Pow er Systems, Inc. 11 Setting switch two to OFF allows the control PCB to perform the A TS control functions. Control system interconnections consist of N1 and N2, and leads 23 and 194. Control system intercon- nection leads must be run in a conduit that is sepa- rate from the AC power lead. Recommended wire gauge sizes for this wiring[...]

  • Page 14

    12 Generac ® Pow er Systems, Inc. When using maintenance -free batteries, it is not nec- essary to check the specific gravity or electrolyte level. Have these procedures performed at the intervals specified in Section 4, “Maintenance.” A negative ground system is used. Battery connections are shown on the wiring diagrams. Make sure all batter-[...]

  • Page 15

    Generac ® Pow er Systems, Inc. 13 • The control board WILL monitor all engine condi- tions and shut down on all the faults listed in this document. Pos2 OFF — Prepackaged A TS Application • The control board will perform all of the automat- ic features listed in this document. • The two -wire start connections should NOT be used. GT S Mode[...]

  • Page 16

    14 Generac ® Pow er Systems, Inc. 3.2.6 SY S TEM READ Y LED The System Ready LED (green) has two main pro- poses. First, the LED will be ON when the A UTO/OFF/MANU AL switch is in the A UTO position, utility is present, and there are no system alarms. This ON state indicates the system is fully ready for automatic operation. The system ready LED w[...]

  • Page 17

    Generac ® Pow er Systems, Inc. 15 On the day , and at the time of day chosen for the gen- erator to exercise, set the weekly exercise cycle as fol- lows: 1. Place the A UTO/OFF/MANU AL switch in the A UTO position. 2. Press and hold the “Set Exercise” switch for three seconds, then release. At this time all five red LEDs will flash for approxi[...]

  • Page 18

    16 Generac ® Pow er Systems, Inc. 4.4 CH E CKI NG F L U I D LEVEL S 4.4.1 CH E CK ENGI NE OI L Check engine crankcase oil level (Figure 4.1) at least every 20 hours of operation, or prior to use. • Remove oil dipstick and wipe dry with a clean, lint -free cloth. • Install oil dipstick, then remove again. • Oil should be between FULL and ADD [...]

  • Page 19

    Generac ® Pow er Systems, Inc. 17 Do not attempt to adjust the governor . Only qualified service facilities should adjust the governor . Excessively high operating speeds are dangerous and incr ease the risk of personal injury . Low speeds impose a heavy load on the engine when adequate engine power is not available and may shorten engine life. Co[...]

  • Page 20

    18 Generac ® Pow er Systems, Inc. 4.6 M IS CELL AN EOUS MAINTENANCE 4.6.1 CLEAN ING TH E GEN ER A T OR Keep the generator as clean and as dry as possible. Dirt and moisture that accumulates on internal gen- erator windings have an adverse effect on insulation resistance. P eriodically clean generator exterior surfaces. A soft brush may be used to [...]

  • Page 21

    Generac ® Pow er Systems, Inc. 19 Section 4 — Maintenance QUIET SOURCE ™ 40kW Liquid-cooled Generators 4.7 S CH EDU LED MAI NTENANCE F ollowing is a recommended maintenance schedule for QuietSource small standby and residential generator sets. The established intervals in the schedule are the maximum recommended when the unit is used in an ave[...]

  • Page 22

    20 Generac ® Pow er Systems, Inc. Section 4 — Maintenance QUIET SOURCE ™ 40kW Liquid-cooled Generators Maintenance Level 1 Level 2 Level 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp . to be done Comp . Required Comp . to be done (Date- 3 months/ (Date- Semi- (Date- to be done (Date- monthly In[...]

  • Page 23

    Generac ® Pow er Systems, Inc. 21 Section 4 — Maintenance QUIET SOURCE ™ 40kW Liquid-cooled Generators Maintenance Level 1 Level 2 Level 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp . to be done Comp . Required Comp . to be done (Date- 3 months/ (Date- Semi- (Date- to be done (Date- monthly In[...]

  • Page 24

    22 Generac ® Pow er Systems, Inc. Section 5 — T roubleshooting QUIET SOURCE ™ 40kW Liquid-cooled Generators TROU B LE SHOO TI NG POI NTS P ROBLEM CAUSE CORR E CTION Engine won’t crank. 1. 15-amp fuse blown. 1. Replace fuse . 2. Loose or corroded or defectiv e 2. Tighten, clean or replace batter y cables . batter y cables as necessary . 3. De[...]

  • Page 25

    Generac ® Pow er Systems, Inc. 23 Section 6 — Installation Diagram QUIET SOURCE ™ 40kW Liquid-cooled Generators Installation Diagram — Drawing No. 0E8 7 9 7[...]

  • Page 26

    24 Generac ® Pow er Systems, Inc. Section 7 - Electrical Data QUIET SOURCE ™ 40kW Liquid-cooled Generators Wiring Diagram — Engine — Drawing No. 0E8 1 1 5-A[...]

  • Page 27

    Generac ® Pow er Systems, Inc. 25 Section 7 - Electrical Data QUIET SOURCE ™ 40kW Liquid-cooled Generators Wiring Diagram — Engine — Drawing No. 0E8 1 1 5-A[...]

  • Page 28

    26 Generac ® Pow er Systems, Inc. Section 7 - Electrical Data QUIET SOURCE ™ 40kW Liquid-cooled Generators Electrical Schematic — Engine — Drawing No. 0E81 16-A[...]

  • Page 29

    Generac ® Pow er Systems, Inc. 27 Section 7 - Electrical Data QUIET SOURCE ™ 40kW Liquid-cooled Generators Electrical Schematic — Engine — Drawing No. 0E81 16-A[...]

  • Page 30

    CONTACTOR WIRE H ARNE SS 4 3 35 13 12 9 34 TO MOU NT E N G INE 18 8 6 7 5 16 3 4 43 42 2 36 41 40 16 6 7 5 19 16 30 27 35 3 4 36 33 27 29 22 20 3 2 38 18 31 20 21 TO S TARTER S TARTER BO LT TO E N G INE B L OC K 18 TO 11 1 12 10 1 4 R EAR BEARIN G 15 3 7 13 C ARRIER 3 4 16 2 28 Generac ® Pow er Systems, Inc. Section 8 - Exploded Views and P arts Q[...]

  • Page 31

    ITEM P ART NO . QTY . DESCRIPTION 1 0E7331 1 WELDMENT MTG BASE 3.9L CR YSLR 2 052860 4 NUT FLANGED HEX M12-1.75 3 052251 4 DAMPENER VIBRA TION 40 BLUE 4 052257 4 SP ACER .49 X .62 X 1.87 PWDR/ZNC 5 052252 4 DAMPENER VIBRA TION 6 052259 4 W ASHER FLA T M12 7 052891 4 SCREW HHC M12-1.75 X 80 G8.8 8 0536210214 1 ASSY WIRE 15.0" 9 074906 1 SCREW H[...]

  • Page 32

    30 Generac ® Pow er Systems, Inc. S TATE S F O AM I S O N NEAR S IDE S TATE S F O AM I S O N FAR S IDE 3 7 17 L AT C H DETAIL 30 1 3 1 3 4 38 3 2 3 45 18 27 41 4 2 S EE LAT CH 7 DETAIL 25 "B" 5 2 11 9 4 6 53 5 5 4 TO "A" S E CU RE A S S H O WN. R E Q UIRE INSULATION. T YPI C AL O F R OO F PANEL THAT 4 53 35 R ADIAT OR 33 4 46 5[...]

  • Page 33

    Generac ® Pow er Systems, Inc. 31 ITEM P ART NO . QTY . DESCRIPTION 1 0E8418 1 DUCT INT AKE MID AL 2 0E8414 1 DUCT DISCHARGE RH AL 3 0E8413 1 DUCT DISCHARGE LH AL 4 0C2454 62 SCREW TH-FRM M6-1 X 16 N W A Z/JS 5 0E7807 1 BAFFLE REAR BOTT OM 6 0E5902 1 POST CORNER LH REAR HSB AL 7 0E5903 1 POST CORNER RH REAR HSB AL 8 0E8387 1 BAFFLE REAR T OP 9 0E5[...]

  • Page 34

    32 Generac ® Pow er Systems, Inc. Section 8 - Exploded Views and P arts QUIET SOURCE ™ 40kW Liquid-cooled Generators Control Panel — Drawing No. 0E7 11 8-H[...]

  • Page 35

    Generac ® Pow er Systems, Inc. 33 ITEM P ART NO . QTY . DESCRIPTION 1 0E7195 1 CONTROL BO X HSB 2 0E7196 1 CO VER FR ONT P ANEL HSB 3 0E7197 1 CO VER TOP P ANEL HSB 4 0E7193 1 DECAL W ARNINGS HSB 5 0E7194 1 DECAL CONTROLS HSB 6 0E4494 1 SWITCH ROC DPDT ON-OFF-ON 7 082573 1 SWITCH R OCKER DPST 125V SPD 8 032300 2 HOLDER FUSE 9 022676 1 FUSE 15A X A[...]

  • Page 36

    Section 8 - Exploded Views and P arts QUIET SOURCE ™ 40kW Liquid-cooled Generators Engine — Drawing No. 0E81 21 -G 34 Generac ® Pow er Systems, Inc.[...]

  • Page 37

    ITEM P ART NO . QTY . DESCRIPTION 1 0E5048A 1 FLEXPLA TE 3.9L HSB 2 0E7477 1 MA CHINING 3.9L ENGINE AD APT OR 3 0E6703 1 CO VER FL YWHEEL ACCESS 4 0E8336 REF REWORK 3.9L CHR YSLER ENGINE 5 0E7841 2 GASKET THERMOST A T ADAPT OR 6 0E7254 1 MA CH THERM AD APT OR 3.9L CHR Y 7 0E7956 1 BRA CKET IGNITION COIL 8 0E7953 1 COIL IGNITION 3.9L CHR YSLER 9 047[...]

  • Page 38

    17 WATER PUMP 24 23 26 24 25 21 3 "A" 13 1 15 19 22 TO T HERM OS TAT HOUS IN G 10 4 10 20 0 5 16 16 2 14 8 15 7 14 18 6 9 1 7 14 O "A" Section 8 - Exploded Views and P arts QUIET SOURCE ™ 40kW Liquid-cooled Generators Radiator — Drawing No. 0E8 1 02-E 36 Generac ® Pow er Systems, Inc.[...]

  • Page 39

    ITEM P ART NO . QTY . DESCRIPTION 1 0D7825A 1 RADIA T OR COPPER BRASS 2 0D7174C 1 VENTURI,3.9L CR YSLR HSB 22"F AN 3 0E7640 1 RADIA TOR SUPPOR T L/H SIDE 4 0E7924 1 HOSE LOWER RADIA T OR 5 0F2853 1 HOSE, RADIA TOR UPPER, 3.9L 6 0D8252 1 F AN GUARD , T OP 7 0D8251 1 F AN GUARD , BO TT OM 8 0E0726 1 BRACKET , W A TER BO TTLE 1.5L MIT 9 076749 1 [...]

  • Page 40

    38 Generac ® Pow er Systems, Inc. 46 21 24 23 TO EN G INE 2 16 17 4 5 6 45 42 40 11 41 9 8 12 6 3 15 2 13 27 3 1 14 19 29 30 3 2 "B " TO "B " 13 36 3 7 38 20 19 18 35 3 4 M ANIF O LD INTAKE TO 44 43 25 22 6 1 39 33 Section 8 - Exploded Views and P arts QUIET SOURCE ™ 40kW Liquid-cooled Generators Fuel Syst em — Drawing No. [...]

  • Page 41

    Generac ® Pow er Systems, Inc. 39 ITEM P ART NO . QTY . DESCRIPTION 1 033212 4 SCREW HHC 5/16-18 X 1-1/4 G5 2 075580 1 FLANGE FUEL INLET 3 0E8365 1 ASSY REG. 3.9L N/G-LPV 1800RPM 4 039253 2 SCREW HHC M8-1.25 X 20 G8.8 5 022145 2 W ASHER FLA T 5/16 ZINC 6 022129 8 W ASHER LOCK M8-5/16 7 045771 2 NUT HEX M8-1.25 G8 YEL CHR 8 042907 2 SCREW HHC M8-1.[...]

  • Page 42

    40 Generac ® Pow er Systems, Inc. 4 15 7 17 8 7 1 18 20 3 1 30 5 21 19 L EAD S 6 2 14 12 24 9 22 * 2 3 13* 3 10 13 11 Section 8 - Exploded Views and P arts QUIET SOURCE ™ 40kW Liquid-cooled Generators Alternator — Drawing No. 0E5 1 46-B[...]

  • Page 43

    Generac ® Pow er Systems, Inc. 41 ITEM P ART NO . QTY . DESCRIPTION 1 0E5093A 1 RO T OR 390 30KW 1P DIRECT HSB 0E7413A 1 RO T OR 390 40KW 1P DIRECT HSB 2 0E5094A 1 STR-390--35AD1 HSB (382MM LONG)(3.0LFORD) 0E7412A 1 STR-390--40AD HSB (433MM LONG)(3.9L CHR YSLER) 3 0E5706 1 REAR BEARING CARRIER 390/DRCT 4 0E5048 REF FLEXPLA TE 3.0L FORD 0E5048A REF[...]

  • Page 44

    ITEM P ART NO . QTY . DESCRIPTION 1 0E8616 1 MUFFLER 7" X 9" X 21" 2.5" IN & OUT 2 0F1081 1 WYE, PIPE 3.9L CHR YSLER 3 0F1087 1 PIPE R/H SIDE 3.9L CHR YSLER 4 0E8026 1 PIPE L/H EXHA UST MANIFOLD 5 0E5914 1 BRA CKET MUFFLER 30" LG 6 0E8702 1 PIPE MUFFLER INLET 7 0E8727 1 PIPE MUFFLER OUT 8 036797 3 BOL T U 5/16-18 X 2.25[...]

  • Page 45

    Section 9 - Notes QUIET SOURCE ™ 40kW Liquid-cooled Generators Generac ® Pow er Systems, Inc. 43[...]

  • Page 46

    44 Generac ® Pow er Systems, Inc. Section 9 - Notes QUIET SOURCE ™ 40kW Liquid-cooled Generators[...]

  • Page 47

    Generac ® Pow er Systems, Inc. 45 Section 9 - Notes QUIET SOURCE ™ 40kW Liquid-cooled Generators[...]

  • Page 48

    Part No. 0E9042 Revision E (03/15/05) Printed in U.S.A. Section 1 0 – W arranty QUIET SOURCE ™ 40kW Liquid-cooled Generators GENER AC PO WER SY STEMS "TWO YEAR" LIMITED WARR ANTY FOR QU I E TS OU RCE™ "PR EP A CKAGED EMERGENCY AUT OMA TIC ST ANDBY GENER A T ORS" F or a period of two years from the date of original sale, Ge[...]