Français dropdown-ico

Graco Inc. 224-224 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Graco Inc. 224-224. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Graco Inc. 224-224 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Graco Inc. 224-224 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Graco Inc. 224-224 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Graco Inc. 224-224
- nom du fabricant et année de fabrication Graco Inc. 224-224
- instructions d'utilisation, de réglage et d’entretien de l'équipement Graco Inc. 224-224
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Graco Inc. 224-224 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Graco Inc. 224-224 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Graco Inc. en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Graco Inc. 224-224, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Graco Inc. 224-224, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Graco Inc. 224-224. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    0432 For use with Class  , Group D paint spray materials 0435 Part No. 235–893 shown I NSTRUCTIONS–P ARTS LIST 308–084 This manual contains IMPORT ANT W ARNINGS AND INSTRUCTIONS READ AND RET AIN FOR REFERENCE Rev . H Supersedes G Model PRO 4600SC  AUT OMA TIC ELECTROST A TIC AIR SPRA Y GUN 100 psi (7 bar) MAXIMUM WORKING PRESSURE U.S. P[...]

  • Page 2

      W ARNINGS SERIOUS BODIL Y INJUR Y , EXPLOSION, FIRE, OR ELECTROST A TIC SHOCK CAN OCCUR IF THE PRECAUTIONS BELOW ARE NOT FOLLOWED. READ AND UNDERST AND ALL INSTRUCTION MANUALS, T AGS, AND W ARNING LABELS BEFORE OPERA TING EQUIPMENT . ELECTROST A TIC EQUIPMENT SHALL ONL Y BE USED BY TRAINED, QUALIFIED PERSONNEL WHO SHALL BE[...]

  • Page 3

    308-084 3 FIRE, EXPLOSION, OR ELECTROST A TIC SHOCK HAZARD T o reduce the risk of fire, explosion, or electrostatic shock, which may result from electrical discharge, it is essential that: S All parts of the electrostatic system are properly grounded. S All personnel in or close to the spray area are properly grounded. S All electric[...]

  • Page 4

      T ABLE OF CONTENTS W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T erms 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation T ypical Installation 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . W arning Signs 5 . . . . . . . . . . . [...]

  • Page 5

      TYPICAL INST ALLA TION Non-Hazardous Area Hazardous Area Fig 1 01769 Controls Cabinet    Shut-off device for fluid only operation Bleed valve or 3 way solenoid Air Regulator Fan Atom Air Lines Grounded T urbine Air Hose (gray[...]

  • Page 6

    6 308-084 INST ALLA TION W ARNING Installing and servicing this equipment requires access to parts which may cause electrostatic shock or other serious bodily injury if work is not performed properly .  Do not install or service this equipment unless you are trained and qualified.  Be sure your installation complies with National, State and L[...]

  • Page 7

      INST ALLA TION To ensure a dry , clean air supply to the gun, install an air line filter and an air and water separator on the air lines. Dirt and moisture can ruin the appearance of your fin- ished workpiece and can cause the gun to malfunction. A combination air filter/moisture separator is shown in the AC[...]

  • Page 8

      INST ALLA TION Check the Electrical Grounding (See Fig 7 ) W ARNING Proper electrical grounding of every part of your system is essential. For your safety , read the warning section, FIRE, EXPLOSION, OR ELECTROST A TIC SHOCK HAZARD , on page 3. Ground the system as explained there. Then check your system as explained below[...]

  • Page 9

      OPERA TION W ARNING Pressure Relief Procedure To reduce the risk of serious bodily injury , including splashing in the eyes or on the skin, injury from moving parts or electrostatic shock, always follow this procedure when shutting of f the system, when checking or servicing any part of the spray system, whe[...]

  • Page 10

    10 308-084 OPERA TION Adjusting the T urbine Air Pressure W ARNING The fan and atomizing air MUST be on before turning on the turbine air . Actuating the turbine air without fan and atomizing air flow could damage the gun and may create hazardous operating conditions and result in serious injury and property damage. 1. Complete all the checks under[...]

  • Page 11

    308-084 1 1 MAINTENANCE Clean the Air Cap and Fluid Nozzle Equipment needed: Soft bristle brush (supplied) Solvent compatible with fluid being sprayed Procedure: 1. Follow the Pressure Relief Procedure W arning on page 9. 2. Remove the air cap assembly and gun shroud. 3. Clean the air cap, fluid nozzle, and front of the gun, using th[...]

  • Page 12

    12 308-084 MAINTENANCE Check for Fluid Leakage (See Fig 10 ) W ARNING If any fluid leakage from the gun is detected, stop spraying IMMEDIA TEL Y! Fluid leakage into the gun shroud could cause fire or explosion and result in serious bodily injury and property damage. During operation, periodically check the two manifold ex - haust tubes and both end[...]

  • Page 13

    308-084 1 3 SPRA Y P A TTERN TROUBLESHOOTING CHART W ARNING Installing and servicing this equipment requires access to parts which may cause electrostatic shock or other seri - ous bodily injury if the work is not performed properly . Do not install or service this equipment unless you are trained and qualified. To reduce the risk of[...]

  • Page 14

    14 308-084 GUN OPERA TION TROUBLESHOOTING CHART Worn fluid rod packings or fluid rod Replace fluid rod packings or rod. See page 23. Fluid rod worn or damaged Replace fluid rod. See page 23. W orn fluid seat Replace fluid nozzle and/or electrode. See page 19 and 20. Piston seal or o-ring damaged Replace seal and/or o-ring and lubricate. Loose resis[...]

  • Page 15

    308-084 1 5 ELECTRICAL TROUBLESHOOTING CHART PROBLEM CAUSE SOLUTION Improper distance between gun Adjust spraying distance to and workpiece 8 to 12 inches (203 to 305 mm). Parts poorly grounded Clean hangers, check for proper ground on conveyer or track. High booth exhaust velocity Reduce exhaust velocity within code limits. Atomizin[...]

  • Page 16

      ELECTRICAL TESTS The performance of the spray gun is directly af fected by the condition of the electrical components contained inside the gun. The electrical tests below can be used to determine the condition of the power supply (40) and the resistor stud (2) as well as the continuity of the electrical path between the[...]

  • Page 17

    308-084 1 7 ELECTRICAL TESTS T est Resistor Stud Resistance (See Fig 13 ) Remove the resistor stud. See Air Cap/Nozzle/Resistor Stud Replacement . Check the resistance between the black resistor stud ring contact (D) and the needle con- tact ring (E). Y ou may have to press down on the contact ring (D) in several places to get a good[...]

  • Page 18

    18 308-084 SERVICE W ARNING Installing and servicing this equipment requires access to parts which may cause electrostatic shock or other serious bodily injury if the work is not performed properly . Do not install or service this equipment unless you are trained and qualified. NOTE: Check all possible remedies in the T roubleshooting Charts before[...]

  • Page 19

    308-084 1 9 SERVICE Air Cap/Nozzle/Resistor Stud Replacement CAUTION BE SURE to hold the front end of the gun up while removing the nozzle and resistor stud. This helps drain the gun and prevent any paint or solvent left in the gun from entering the air passages. 1. Point the front end of the gun up while removing the fluid nozzle (1[...]

  • Page 20

      SERVICE Electrode Replacement 1. Remove the air cap, nozzle and resistor stud as described in Air Cap/Nozzle/Resistor Stud Replacement . 2. Unscrew and remove the fluid needle/electrode (28) with the electrode tool (47) provided. Be careful not to damage the contact wire. See Fig 17 . If the fluid rod turns, hold the ba[...]

  • Page 21

    308-084 2 1 SERVICE Barrel Removal 1. Carefully loosen the fluid fitting nut (21). Pull the tube (19) out of the fitting. Make sure both ferrules and the nut stay with the tube. See Fig 19 . 2. Remove the jam nut (25) and actuator arm (29). NOTE: The fluid nozzle must be in place when removing or installing the jam nut and actuator a[...]

  • Page 22

      SERVICE Barrel Installation 1. Be sure the gaskets (23 & 40a) and spring (1 1) are in place. See Fig 20 . Replace if damaged. 2. Place the barrel (10) over the power supply (40) and onto the gun body (39). Make sure the fluid rod spring (1 1) is seated properly . 3. T ighten the three socket head cap screws (15) opp[...]

  • Page 23

    308-084 2 3 SERVICE Fluid Packing Rod Removal and Repair NOTE: The fluid packing rod can be replaced as individual parts or as an assembly . If the assembly is purchased, it is pre-adjusted at the factory . 1. Remove the jam nut (25) and arm (29). See Fig 20 . 2. Remove the air cap assembly , fluid nozzle and resis - tor stud and ele[...]

  • Page 24

      SERVICE Fluid Packing Rod Removal and Repair (continued) 8. Place the fluid packing (3f), rod packing (3e), and housing (3a) on the fluid rod (3b) as shown in Fig 22 . 9. Lightly tighten the packing nut (3c). The packing nut is properly tightened when there is 2 lbs. (9 N) of drag force when sliding the packing housing [...]

  • Page 25

    308-084 2 5 SERVICE Fig 23 KEY F 3-wire Connector G Potentiometer 10 Gun Barrel 13 Retainer Ring 27 Alternator 27a O-Ring 27b Cushion 39 Gun Body 40 Power Supply 40a Gasket 40b Pad 40c Pad 40d Seal 40e Cushion 39 13 27a 27b 40a 40 27 F 10 40b 40c 40e G 40d 0450 Power Supply Removal and Replacement REP AIR NOTES: a. T o avoid a loss i[...]

  • Page 26

      SPRA Y GUN SERVICE NOTES Lubricate Lubricate Apply high strength (red) Loctite or equivalent to threads. Lubricate Lubricate T ighten Resistor Stud into nozzle to 10 in-lbs (1.15 N  m) T ighten Nozzle 1/8 to 1/4 turn past hand tight T orque Fitting to 25–35 in-lbs (2.8–4.0 N  m) CAUTION: Do not damage Needle E[...]

  • Page 27

    308-084 2 7 MANIFOLD SERVICE NOTES 0434 0434 Press fit This end 8.5-8.9” (215-225 mm) from manifold surface when properly assembled Standard o-ring is V iton. Optional EPR o-ring is provided with the man - ifold for compatibility with ketone solvents. Must be clean Press fit T ighten until hex bottoms against manifold Left-hand thr[...]

  • Page 28

      SPRA Y GUN P ARTS DRA WING DET AIL A 0433 See Detail A 3b 3 28 31 2 14 9 16 43 12 6 18 40e 40b 27a 27 27b 13 40c 40 40d 40a 23 22 42 15 10 36 30 19 25 29 REF 3 11 20 7 REF 19 21a 21b 5 21 39 36 17 1 4 8 32 24 41d 41j 41e 41g 41i 41b 41c 41h 41a 41f 41 REF NO. 3 Includes items 3a–3h 3a 3h 3c 3d 3e 0601 3f 3g[...]

  • Page 29

     308-084 2 9 SPRA Y GUN P ARTS LIST Part No. 224–224 Automatic Electrostatic Air Spray Gun, without shroud Includes items 1–17, 19–52 Part No. 235–893, Series A Air Spray Gun, with standard shroud Includes items 1–52 Part No. 235–894, Series A Air Spray Gun, with slotted shroud Includes items 1–52 REF NO. P ART NO[...]

  • Page 30

      MANIFOLD P ARTS DRA WING 0434 122 1 17d 1 17c 1 17h 1 17b 1 17g 1 17e 1 17f 11 8 11 0 11 4 111 11 6 106 104 104 11 3 11 5 107 108 109 101 121 11 2 124 103 MANIFOLD P ARTS LIST Part No. 224–094 Gun Manifold Includes items 101–124 REF NO. P ART NO. DESCRIPTION QTY 101 1 1 1–224 LENSE 1 103* 106–167 O-RING; perfluo[...]

  • Page 31

    308-084 3 1 PRO 4600HC CONVERSION KIT Part No. 237–301 PRO 4600HC Conversion Kit ; T o convert the PRO 4600SC  spray gun to the PRO 4600HC spray gun. The longer 20 in. (508 mm) fluid tube used by the HC gun provides increased spraying voltage when spray - ing highly conductive fluids. The kit must be ordered separately . It incl[...]

  • Page 32

      ACCESSORIES Accessories must be purchased separately . Use only GENUINE GRACO P ARTS AND ACCESSORIES. AIR AND FLUID LINE ACCESSORIES Air Pilot Paint Regulator 224–531 For controlling paint flow through the spray gun. Connects to mount assembly 235–094. 0331 Grounded Air Supply Hose 100 psi (7 bar) MAXIMUM WORKING PR[...]

  • Page 33

    308-084 3 3 ACCESSORIES Accessories must be purchased separately . Use only GENUINE GRACO P ARTS AND ACCESSORIES. GUN MOUNTING ACCESSORIES Gun Mount Assembly 235–094 01875 Bracket for mounting to a 1/2 inch (12.7 mm) rod, with a slot for mount - ing the air pilot fluid regulator 224–531. Gun Mount Assembly 224–118 For mounting [...]

  • Page 34

      ACCESSORIES Accessories must be purchased separately . Use only GENUINE GRACO P ARTS AND ACCESSORIES. CABLE ACCESSORIES Fiber Optic Cables Fiber Optic Cable Assembly For connection between gun manifold and display module or between bulkhead connector and display module. PA R T NO. LENGTH 224–680 6 ft (1.8 m) 224–681[...]

  • Page 35

       Safety W arning Signs Available at no charge from Graco. Must be ordered separately . PA R T NO. DESCRIPTION 180–060 W arning Sign (English) 180–061 W arning Sign (French) 180–062 W arning Sign (German) 180–063 W arning Sign (Spanish) Paint Resistance Meter 722–886 Used with 722–860 Paint Pro[...]

  • Page 36

    36 308-084 THE GRACO W ARRANTY AND DISCLAIMERS W ARRANTY Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workman - ship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser ’ s sole remedy for breach of this warranty , Graco will, for a [...]