Lenovo 6523 manuel d'utilisation

Installation and User Guide ThinkServer TS200 Machine T ypes: 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530[...]

[...]

ThinkS e rv e r T S2 00 T yp es 65 2 2, 652 3 , 652 4 , 65 2 5 , 65 2 6, 65 2 8 , 652 9 , a n d 653 0 In stall a ti o n a n d U s e r G ui d e[...]

Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 183 and the Warranty and Support Information document on the Lenovo ® ThinkServer Documentation DVD. First Edition (November 2009) © Copyright Lenovo 2009. Portions © Copyright International Business Machines Corpor[...]

Contents Safety ............................ v i i Chapter 1. Introduction ...................... 1 Notices and statements in this document ................ 2 Related documentation ...................... 3 Chapter 2. Server setup roadmap .................. 5 Chapter 3. What is included with your server ............. 7 Features and technologies ....[...]

Power and signal cables for internal drives ............. 5 4 Removing an adapter ...................... 5 5 Installing an adapter ....................... 5 7 Removing a PCI card ...................... 5 9 Installing a PCI card ....................... 6 0 Removing a USB embedded hypervisor flash device ........... 6 1 Installing a USB embedded hype[...]

Starting the Setup Utility .................... 1 1 0 Setup Utility menu choices ................... 1 1 0 Passwords ......................... 1 1 3 Using the Boot Manager program ................. 1 1 4 RAID controllers ........................ 1 1 5 Using the WebBIOS utility ................... 1 1 5 Using the ThinkServer EasyStartup program ....[...]

Diagnostics messages ..................... 1 7 8 Appendix A. Getting help and technical assistance .......... 1 7 9 Before you call ........................ 1 7 9 Using the documentation ..................... 1 7 9 Getting help and information from the World Wide W eb ......... 1 7 9 Calling for service ....................... 1 8 0 Using other ser[...]

Safety Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instal ací tohoto produktu si prectete prír ucku bezpecnostních instr ukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Lees voordat u dit product installeert eerst de veiligheidsvoor[...]

Antes de instalar este producto, lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här produkten. Important: Each caution and danger statement in this document is labeled with a number . This number is used to cross reference an English-language caution or danger statement with translated versions of the cauti[...]

Statement 1: DANGER Electrical current from power , telephone, and communication cables is hazardous. T o avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v[...]

Statement 2: CAUTION: When replacing the lithium battery , use only Part Number 33F8354 or an equivalent type battery . If your system has a module containing a lithium battery , replace it only with the same module type made by the same manufacturer . The battery contains lithium and can explode if not properly used, handled, or disposed of. Do no[...]

Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. v Use of controls or adjustment[...]

Statement 4: ≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. T o remove al[...]

Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service tec[...]

DANGER Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. T o avoid these hazards, ensure that your system electrical requirements do not exceed branch circuit protection requirements. Refer to the information that is provided with your device for electrical specifications. Statement 15: CAUTION: [...]

Chapter 1. Introduction This Installation and User Guide is intended to use with your Lenovo ® ThinkServer ™ TS200 (Machine T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530) server . This document contains information about: v Setting up and cabling the server v Starting and configuring the server v Installing options and replacing cust[...]

1 Model and machine type For a list of supported optional devices for the server , go to http://www .lenovo.com/thinkserver and click the Options tab. Notices and statements in this document The caution and danger statements that appear in this document are also in the multilingual Safety Information document, which is on the Lenovo ThinkServ[...]

Related documentation The Lenovo ThinkServer Documentation DVD contains documentation for the server in Portable Document Format (PDF). The Lenovo ThinkServer Documentation DVD requires the Adobe ® Reader 5.0 (or later) or xpdf, which comes with Linux ® operating systems. The following table describes the content and location of documentation tha[...]

4 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Chapter 2. Server setup roadmap The installation process varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configured and just needs to be connected to power and the network and started. In other cases, the server needs to have hardware features installed, requires hardware and firmware co[...]

6 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Chapter 3. What is included with your server The TS200 server package includes the server , power cords, the ThinkServer Documentation DVD, and software media. 1 Server 2 Power cords 3 Documentation and software media Features and technologies The TS200 server of fers the following features and technologies: v UEFI-compliant serve[...]

v Remote presence capability and blue-screen capture The remote presence feature provides the following functions: – Remotely viewing video with graphics resolutions up to 1600 x 1200 at 85 Hz, regardless of the system state – Remotely accessing the server , using the keyboard and mouse from a remote client – Mapping the CD or DVD drive, disk[...]

The command-line interface provides direct access to server management functions through the IPMI 2.0 protocol. Use the command-line interface to issue commands to control the server power , view system information, and identify the server . Y ou can also save one or more commands as a text file and run the file as a script. v Large data-storage ca[...]

Specifications The following information is a summary of the features and specifications of the server . Depending on the server model, some features might not be available, or some specifications might not apply . T able 2. Features and specifications Microprocessor: v Supports one Intel ® Xeon ® 3400 series quad-core microprocessor v Designed f[...]

T able 2. Features and specifications (continued) RAID controllers: v ServeRAID BR10il v ServeRAID-MR10i v ServeRAID-M1015 v ServeRAID M5015 v ServeRAID MR10is V AUL T Acoustical noise emissions: v Sound power , idling: 6.5 bels maximum v Sound power , operating: 6.5 bels maximum Environment: v Air temperature: – Server on: 10°C to 35°C (50.0°[...]

Reliability , availability , and serviceability Three important server design features are reliability , availability , and serviceability (RAS). The RAS features help to ensure the integrity of the data that is stored on the server , the availability of the server when you need it, and the ease with which you can diagnose and correct problems. The[...]

v W ake on LAN capability Chapter 3. What is included with your server 13[...]

14 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Chapter 4. Server controls, LEDs, and power This section describes the controls and light-emitting diodes (LEDs) and how to turn the server on and off. Front view The following illustrations show the controls, LEDs, and connectors on the front of the server models. The following is an illustration of the 3.5-inch SAS/SA T A hot-swap hard disk drive[...]

1 Simple-swap hard disk drive 6 Hard disk drive activity LED 2 DVD drive activity LED (green) 7 System error LED 3 Front information panel 8 USB 2 4 Power-on LED 9 USB 1 5 Power-control button 10 DVD-eject button DVD drive activity LED: When this LED is lit, it indicates that the DVD drive[...]

Fading on and off: The server is in a reduced-power state. T o wake the server , press the power-control button or use the IMM Web interface. See “Logging on to the Web interface” on page 125 for information on logging on to the IMM W eb interface. Hard-disk drive activity LED: When this LED is flashing, it indicates that a hard disk drive is i[...]

Rear view The following illustration shows the connectors and LEDs on the rear of the server . 1 USB 3 and 4 5 Serial (Com1) 2 USB 1 and 2 6 Power cord connector 3 Ethernet connectors 7 Ethernet transmit/receive activity LED (amber) 4 Video connector 8 Ethernet link status LED (green) USB 1-4 connecto[...]

System-board internal connectors The following illustrations show the internal connectors and switches on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs Chapter 4. Server controls, LEDs, and power 19[...]

1 DIMM 1 11 Fan 1 connector 21 Slot 2: PCIe2 x8, 25w 2 DIMM 2 12 Hard disk backplane configuration connector 22 Slot 1: PCIe2 x8, 25w 3 DIMM 3 13 Operator information panel connector 23 Battery 4 DIMM 4 14 Simple-swap HDD backplane signal connector 24 Power 2 connector 5 [...]

3 Ethernet connector 1 7 SW1 (NMI button) 4 USB connectors 1 and 2 System-board switches and jumpers The following illustration shows the switches and jumpers on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs The following table describes the jumpers on the system board. T able 3. System board jumpers Jumper num[...]

Important: 1. Before you change any switch settings or move any jumpers, turn off the server; then, disconnect all power cords and external cables. Review the information in “Installation guidelines” on page 29, “Handling static-sensitive devices” on page 31, and “T urning off the server” on page 28. 2. Any system-board switch or jumper[...]

T able 4. System-board LEDs (continued) LED Description Baseboard management controller heartbeat LED This LED flashes to indicate that the IMM is functioning normally . Standby power LED When this LED is lit, it indicates that the server is connected to ac power . The following table describes the LEDs on the system board and extender card and sug[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(T rained[...]

1 AC power LED 2 DC power LED 3 Fault LED 4 Fault LED 5 Power LED The following table describes the problems that are indicated by various combinations of the power-supply LEDs and the power-on LED on the front information panel and suggested actions to correct the detected problems. Chapter 4. Server controls, LEDs, a[...]

T able 5. Power-supply LEDs Power-supply LEDs Description Action Notes AC DC Error Off Of f Off No ac power to the server or a problem with the ac power source 1. Check the ac power to the server . 2. Make sure that the power cord is connected to a functioning power source. 3. T urn the server off and then turn the server back on. 4. If the problem[...]

the server is connected to ac power , the power-control button becomes active (the power-on LED flashes slowly). Y ou can turn on the server by pressing the power-control button. The server can also be turned on in any of the following ways: v If a power failure occurs while the server is turned on, the server will restart automatically when power [...]

T urning off the server When you turn off the server and leave it connected to ac power , the server can respond to requests to the service processor , such as a remote request to turn on the server . While the server remains connected to ac power , one or more fans might continue to run. T o remove all power from the server , you must disconnect i[...]

Chapter 5. Installing and replacing optional devices This chapter provides detailed instructions for installing optional hardware devices in the server . Installation guidelines Before you install optional devices, read the following information: v Read the safety information that begins on page vii, “Working inside the server with the power on?[...]

devices. However , you must turn off the server before performing any steps that involve removing or installing adapter cables or non-hot-swap optional devices or components. v Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the server , open or close a latch, and so on. v Orange on a [...]

v Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirts before working inside the server; do not wear cuff links while you are working inside the server . v Do not allow your necktie or scarf to hang inside the server . v Remove jewelry , such as bracelets, necklaces, rings, and loose-fitting wrist watches. v Remove item[...]

Server components The following illustration shows the major components in the server . 1 Cover 10 SA T A hard disk drive (some models) 2 Non-hot-swap power supply 11 Hot-swap hard disk drive (some models) 3 System board 12 Front adapter-support bracket 4 DIMM 13 Drive cage 5 Rear system fan [...]

Attention: Operating the server for more than 30 minutes with the side cover removed might damage server components. For proper cooling and airflow , replace the side cover before turning on the server . 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devi[...]

3. Position the lip on the bottom edge of the side cover on the ledge on the bottom of the chassis; then, rotate the cover up to the chassis. Press down on the cover release latch and push the cover completely closed until it latches securely into place. 4. Lock the side cover . 5. Reconnect the external cables and power cords; then, turn on the at[...]

5. Lift the lower bezel to disengage the two bottom tabs from the chassis. Set the lower bezel aside. Chapter 5. Installing and replacing optional devices 35[...]

6. Carefully pull the two bezel clips 1 on the left side of the upper bezel away from the chassis; then, rotate the upper bezel to the right side of the server to disengage the two right-side tabs from the chassis. Set the upper bezel aside. For instructions for replacing the two-piece bezel, see “Installing the lower bezel” and “Instal[...]

2. Rotate the top of the lower bezel up to the chassis; then, press the blue release tab on the right side of the lower bezel and completely close the lower bezel until it locks securely into place. 3. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server . Installing the upper bezel T o install th[...]

6. If you are instructed to return the DIMM, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a memory module The following notes describe the types of dual inline memory modules (DIMMs) that the server supports and other information that you must consider when you install DIMMs (s[...]

where: ggg is the total capacity of the DIMM (for example, 1GB, 2GB, or 4GB) e is the number of ranks 1 = single-rank 2 = dual-rank 4 = quad-rank ff is the device organization (bit width) 4 = x4 organization (4 DQ lines per SDRAM) 8 = x8 organization 16 = x16 organization wwwww is the DIMM bandwidth, in MBps 8500 = 8.53 GBps (PC3-1066 SDRAMs, 8-byt[...]

v The following table lists the supported UDIMM population. T able 6. Supported UDIMM population per channel DIMMs slots per channel DIMMs installed in each channel DIMM type DIMM speed Ranks per DIMM (any combination) 2 1 Unbuffered DDR3 ECC 1066, 1333 single-rank, dual-rank 2 2 Unbuffered DDR3 ECC 1066, 1333 single-rank, dual-rank v The following[...]

v The following table lists the supported RDIMM population. T able 9. Supported RDIMM population per channel DIMMs slots per channel DIMMs installed in each channel DIMM type DIMM speed Ranks per DIMM (any combination) 3 1 Registered DDR3 ECC 1066, 1333 single-rank, dual-rank 3 2 Registered DDR3 ECC 1066, 1333 single-rank, dual-rank 3 3 Registered [...]

T o install a DIMM, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and peripheral devices and disconnect the power cords and all external cables, if necessary . 3. Remove the cover (see “Removing the side cover” on page 32). 4. Locate the[...]

If you have other devices to install or remove, do so now; otherwise, go to “Completing the installation” on page 67. Removing and installing internal drives See “Specifications” on page 10 for information about the types of drives that the server supports and other important information. The following figure shows the locations of the driv[...]

The following notes describe the types of drives that the server supports and other information that you must consider when installing a drive: v Make sure that you have all the cables and other equipment that is specified in the documentation that comes with the drive. v Select the bay in which you want to install the drive. v Check the instructio[...]

1 Release buttons 2 Drive retainer clip 7. Remove the drive retainer clip from the side of the drive. Save the clip to use when you install the replacement drive. 8. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a DVD drive [...]

Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. v Use of controls or adjustment[...]

1 Release buttons 2 Drive retainer clip 5. Push the drive into the bay . 6. Connect the power and signal cables to the drive. Note: Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and dual inline memory modules (DIMMs). 7. Install the upper bezel (see “Installing the up[...]

1 EMC shield 2 T ape drive 3 Drive retainer clip 9. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a tape drive T o install a tape drive, complete the following steps: 1. If you are replacing a removed drive with a new [...]

8. Set any jumpers or switches on the drive according to the documentation that comes with the drive. 9. Remove the drive retainer clip from the side of the drive cage of bay 1 or bay 2. Slide the drive retainer clip to the front to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive. 1[...]

T o remove a hot-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. Note: Y ou do not have to turn off the server to remove hot-swap drives from the hot-swap drive bays. 2. Remove the lower bezel (see “Removing the two-piece bezel” on page 34).[...]

T able 13. IDs of the hot-swap drives (models with four drive bays) Drive bay ID 40 51 62 73 Installing a hot-swap hard disk drive This procedure applies only to server models that have hot-swap hard disk drives. Before you install a hot-swap hard disk drive, read the following information: v The hot-swap drives must be either all SAS hard disk dri[...]

1. T ouch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 2. Make sure that the drive tray handle is in the open position. 3. Align the drive assembly with the guide rails in the bay; then, carefully slide the dri[...]

Removing a simple-swap hard disk drive This procedure applies only to server models that have simple-swap SA T A hard disk drives. Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before you remove or install a simple-swap hard disk drive. T o remove a simple-swap hard disk drive, complete the foll[...]

Installing a simple-swap hard disk drive This procedure applies only to server models that have simple-swap SA T A hard disk drives. Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server you remove or install a simple-swap hard disk drive. T o install a simple-swap hard disk drive, complete the followin[...]

v The drives that are preinstalled in the server come with power and signal cables attached. If you replace any drives, remember which cable is attached to which drive. v When you install a drive, make sure that one of the signal cable drive connectors is connected to the drive and that the connector at the other end of the signal cable is connecte[...]

7. Remove the expansion-slot screw 2 at the rear of the adapter 3 if any . 8. Carefully grasp the adapter by its top edge or upper corners. And pull the adapter from the server . Attention: Expansion-slot covers must be installed in all empty slots. This maintains the electronic emissions standards of the computer and ensures proper ven[...]

Installing an adapter The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter . Adapter that the server supports might vary , depending on your server model. v Locate the documentation that comes with the adapter and follow those instructions in addition to[...]

6. Remove the screw that secures the expansion-slot cover to the chassis. Store the expansion-slot cover and screw in a safe place for future use. Note: Expansion-slot covers must be installed on all vacant slots. This maintains the electronic emissions standards of the server and ensures proper ventilation of server components. 1 Rear adapte[...]

8. If you are installing a full-length adapter , remove the blue adapter guide (if any) from the end of the adapter . 1 Adapter guide 9. Carefully grasp the adapter by the top edge or upper corners, and align it with the expansion slot guides; then, press the adapter firmly into the expansion slot. Move the adapter directly from the static-pr[...]

Attention: T o avoid breaking the retaining clips or damaging the adapter connector , open and close the clips gently . 5. Carefully grasp the end of the adapter and pull it out of the connector . 6. If you are instructed to return the adapter , follow all packaging instructions, and use any packaging materials for shipping that are supplied to you[...]

9. T ake the other end of the signal cable that is attached to the drive backplane section for drive bays 0 through 3 (as labeled on the front of the drive cage) and connect it to the connector that is closest to the battery on the PCI card. 10. Replace the hard disk drive fan assembly: a. Insert the hard disk drive fan assembly retaining tab over [...]

5. Align the flash device with the connector on the system board and push it into the connector until it is firmly seated. 6. Press down on the retaining latch to lock the flash device into the USB connector . 7. Reconnect the power cord and any cables that you removed. 8. Install and lock the side cover (see “Installing the side cover” on page[...]

4. If you are instructed to return the virtual media key , follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the virtual media key T o install the virtual media key , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines?[...]

Removing a hot-swap power supply This procedure applies only to server models that have hot-swap power supplies. See “Installing a non-hot-swap power supply” on page 98 for information about the removal of a non-hot-swap power supply . When you remove or install a hot-swap power supply , observe the following precautions. Statement 8: CAUTION: [...]

T o remove a hot-swap power supply , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. Disconnect the power cord from the power supply that is to be removed. 3. Press down on the release lever 1 and pull the power supply 2 out of the bay , using the hand[...]

1 Release lever 2 Hot-swap power supply 2. Using the handle, push the power supply toward the front of the chassis until it locks into place. 3. Connect one end of the power cord into the connector on the back of the power supply and connect the other end of the power cord into a properly grounded electrical outlet. 4. Make sure that bo[...]

4. Thread the cable through the rope clip and around an object that is not part of or permanently secured to the building structure or foundation, and from which the cable cannot be removed. Fasten the cable ends together with a lock. After you add the security cable, make sure that it does not interfere with other cables that are connected to the [...]

68 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

2. Install the lower bezel: a. Insert the two bottom tabs on the lower bezel into the matching holes in the front of the chassis. b. Rotate the top of the lower bezel up to the chassis; then, press the blue release tab on the right side of the lower bezel and completely close the lower bezel until it locks securely into place. Chapter 5. Installing[...]

Reinstalling the side cover If you removed the side cover , reinstall it. Note: The rear adapter-retention bracket rests against the server side cover . Y ou might find it easier to lay the server on its side to replace the side cover . T o reinstall the side cover , complete the following steps: 1. Make sure that all cables, adapters, and other co[...]

Connecting the cables Attention: T o prevent damage to equipment, connect the power cords last. If the server cables and connector panel have color-coded connections, match the color of the cable end with the color of the connector . For example, match a blue cable end with a blue panel connector , a red cable end with a red connector , and so on. [...]

72 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Chapter 6. Installing and replacing customer replaceable units Removing the rear system fan Attention: v Replace a failed fan within 48 hours. v T o ensure proper cooling and airflow , do not operate the server for more than 30 minutes with the side cover removed. T o remove the rear system fan, complete the following steps: 1. T urn off the server[...]

Installing the rear system fan Attention: v Replace a failed fan within 48 hours. v T o ensure proper cooling and airflow , do not operate the server for more than 30 minutes with the side cover removed. T o install the rear system fan, complete the following steps: 1. The replacement fan comes with the rubber grommets installed 1 ; however ,[...]

Removing the hard disk drive fan assembly This procedure applies only to server models that have a hard disk drive fan assembly . Attention: v Replace a failed fan within 48 hours. v T o ensure proper cooling and airflow , do not operate the server for more than 30 minutes with the side cover removed. T o remove the hard disk drive fan assembly , c[...]

9. Pull out on the hard disk drive fan assembly release tabs; then, rotate the assembly away from the drive cage slightly . 1 Release tabs 2 Hard disk drive fan assembly 3 Slot 10. Remove the cable from the slot on the hard disk drive fan assembly; then, rotate the assembly away from the drive cage and remove the assembly from the[...]

1 Release tabs 2 Hard disk drive fan assembly 3 Slot 2. Route the hard disk drive signal and power cables through the slots on the edge of the hard disk drive fan assembly . Make sure that the cables will not be pinched between the hard disk drive assembly and the hard disk drive backplane when the assembly is installed. 3. Rotate[...]

5. Connect the hard disk drive fan assembly cable to the system board (see “System-board internal connectors” on page 19 for the location of the hard disk drive fan connector). 6. Reinstall the hard disk drives. Note: Before you continue, check all internal power cables to be sure that they are connected to the system board and other optional d[...]

1 Retaining tab 2 Drive cage release tab 3 Locating pins 4 Simple-swap backplate 5 Retaining latch 1 1. Lift the simple-swap backplate out of the lower lip on the drive cage and set it aside. 12. If you are instructed to return the simple-swap backplate, follow all packaging instructions, and use any packaging material[...]

1 Retaining tab 2 Drive cage release tab 3 Locating pins 4 Simple-swap backplate 5 Retaining latch 2. T ilt the top of the simple-swap backplate toward the drive cage and over the locating pins until the retaining latch is engaged securely . 3. Press and hold the retaining tab on top of the cage; then, rotate the drive[...]

Removing the SAS/SA T A hard disk drive backplane This procedure applies only to hot-swap server models with a SAS/SA T A hard disk drive backplane installed on the back of the hard disk drive cage. T o remove the SAS/SA T A hard disk drive backplane, complete the following steps: 1. Read the safety information that begins on page vii and “Instal[...]

10. T ilt the top of the hard disk drive backplane away from the drive cage until it is clear of the locating pins. 1 1. Lift the SAS/SA T A hard disk drive backplane out of the lower lip on the drive cage and set it aside. 12. If you are instructed to return the SAS/SA T A hard disk drive backplane, follow all packaging instructions, and use any p[...]

6. Install the hard disk drive fan assembly onto the hard disk drive cage (see “Installing the hard disk drive fan assembly” on page 76). 7. Install the hot-swap hard disk drives that you removed from the hard disk drive cage (see “Installing a hot-swap hard disk drive” on page 51). 8. Install the lower bezel (see “Installing the lower be[...]

1. Position the front end of the front-panel assembly in the channel above drive bay 1 on the left side of the chassis. 2. Push the front-panel assembly 1 toward the front of the chassis until it clicks into place. 3. Reroute and connect the front-panel assembly cable to the system board (see “System-board internal connectors” on page 19 [...]

7. Squeeze the spring clips 1 on the sides of the front USB connector assembly and pull the assembly out of the back of the housing. 8. Carefully pull the front USB cable out of the opening in the chassis. 9. If you are instructed to return the front USB connector assembly , follow all packaging instructions, and use any packaging materials f[...]

9. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server . Removing the rear adapter retention bracket T o remove the rear adapter-retention bracket, complete the following steps: 1. T urn off the server and all attached devices; then, disconnect all power cords and external cables. 2. Unlock and r[...]

Removing the front adapter-retention bracket T o remove the front adapter-retention bracket, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Unlock and remove t[...]

5. Disconnect the cables from the power-supply cage to the system board and all internal components. 6. Remove the four black screws that secure the power-supply cage to the chassis; then, slide the cage toward the front of the server to disengage the retaining clips 1 from the top of the chassis and lift the cage out of the chassis. 7. If yo[...]

2. Install the four screws that secure the power-supply cage to the chassis. 3. Connect the cables from the power-supply cage to the system board and all internal components (see “System-board internal connectors” on page 19 for the locations of the internal connectors). 4. Reinstall both hot-swap power supplies (see “Removing the hot-swap po[...]

CAUTION: When replacing the lithium battery , use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer . If your system has a module containing a lithium battery , replace it only with the same module type made by the same manufacturer . The battery contains lithium and can explode if not properly used, handled, or[...]

Removing a ServeRAID BR10-il controller T o remove the ServeRAID BR10-il controller , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables. Note: When you disconnect the[...]

plastic standoff. 3. Connect the signal cable to the SAS/SA T A controller . 4. Install and lock the side cover (see “Installing the side cover” on page 33). 5. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server . Removing an optional ServeRAID-MR10i SAS/SA T A controller T o remove a ServeR[...]

Attention: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. T o install a ServeRAID-MR10i adapter , complete the following steps: 1. Read the safety information beginning[...]

7. Press the ServeRAID-MR10i adapter firmly into the connector on the system board. 8. Reconnect the cables to the new ServeRAID-MR10i adapter . Removing an optional ServeRAID-MR10is V AUL T SAS/SA T A controller T o remove a ServeRAID-MR10is SAS/SA T A adapter , complete the following steps: 1. Read the safety information beginning on page vii, an[...]

1 Battery 2 Battery carrier 3 RAID adapter 4 Connector for battery carrier b. Press the battery carrier into the connector on the ServeRAID adapter until it is firmly connected. c. Secure the battery carrier to the ServeRAID adapter with the screws that came with the battery pack. 4. T urn the ServeRAID-MR10is adapter so tha[...]

2 PCI slot 5. Press the ServeRAID-MR10is adapter firmly into the connector on the system board. 6. Reconnect the cables to the new ServeRAID-MR10is adapter . Make sure that the ServeRAID-MR10is SAS/SA T A adapter is cabled. 7. Rotate the rear adapter-retention bracket to the closed (locked) position. 8. Install the side cover (see “Installi[...]

T o remove a non-hot-swap power supply , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Unlock and remove the side cover (see “Removing the side cover” on [...]

Installing a non-hot-swap power supply This procedure applies only to server models that have a non-hot-swap power supply . See “Removing the hot-swap power supply cage” on page 87 for information about the installation of a hot-swap power supply . T o install a non-hot-swap power supply , complete the following steps: 1. Position the power sup[...]

Removing the microprocessor and fan sink T o remove the microprocessor and fan sink, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables. 3. T urn the server on its sid[...]

c. T ip the top of the fan sink toward the front of the server while you slide it away from the lower flange of the retention module; then, remove it from the server . After removal, place the fan sink on its side on a clean, flat surface. Attention: The microprocessor retention latch is spring-loaded when the microprocessor is in place. Releasing [...]

Installing a microprocessor and fan sink T o install the microprocessor , complete the following steps: 1. T ouch the static-protective package that contains the microprocessor to any unpainted metal surface on the server . Then, remove the microprocessor from the package. 2. Remove the protective cover , tape, or label from the surface of the micr[...]

a. Make sure that the fan sink retention lever is in the fully open position. Important: Be careful when you handle the microprocessor and fan sink. Do not contaminate the thermal material between them. b. Slide the bottom edge of the fan sink under the lower flange of the retention module; then, place the top of the fan sink onto the top of the re[...]

Note: v Read the Safety information on page vii. v Read the “Installation guidelines” on page 29. T o replace damaged or contaminated thermal grease on the microprocessor and fan sink, complete the following steps: 1. Place the fan sink on a clean work surface. 2. Remove the cleaning pad from its package and unfold it completely . 3. Use the cl[...]

Removing the system board T o remove the system board, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables. 3. T urn the server on its side so that it is lying flat, wi[...]

9. Remove the eight screws (seven in front and one in rear) 1 that secure the system board to the chassis. 10. Slide the system board toward the front of the server to disengage the tabs on the fan sink mounting bracket from the slots on the bottom of the chassis; then, carefully lift the system board out of the server . 1 1. Remove the fan c[...]

12. If you are instructed to return the system board, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the system board T o install the system board, complete the following steps: 1. T ouch the static-protective package that contains the system board to any unpainted metal surface [...]

5. Install the eight screws (seven in front and one in rear) that secure the system board to the chassis. 6. Install any of the following components that you removed from the system board: v The fan connector covers. v Hypervisor key (see “Installing a USB embedded hypervisor flash device” on page 61). v Virtual media key (see “Installing the[...]

108 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Chapter 7. Configuring the server The following configuration programs come with the server: v Setup Utility The Setup Utility (formerly called the Configuration/Setup Utility program) is part of the server firmware. Use it to change the startup-device sequence, set the date and time, and set passwords. For information about using this program, see[...]

T able 14. Server configurations and applications for configuring and managing RAID arrays (continued) Server configuration RAID array configuration (before operating system is installed) RAID array management (after operating system is installed) ServeRAID-MR10i SAS/SA T A Controller (LSI 1078) installed MegaRAID Storage Manager (MSM), MegaRAID BI[...]

Utility , the changes are reflected in the system summary; you cannot change settings directly in the system summary . – Product Data Select this choice to view the system-board identifier , the revision level or issue date of the firmware, the integrated management module and diagnostics code, and the version and date. v System Settings Select t[...]

- Network Configuration Select this choice to view the system management network interface port, the IMM MAC address, the current IMM IP address, and host name; define the static IMM IP address, subnet mask, and gateway address; specify whether to use the static IP address or have DHCP assign the IMM IP address; save the network changes. - Reset IM[...]

v User Security Select this choice to set, change, or clear passwords. See “Passwords” for more information. This choice is on the full and limited Setup Utility menu. – Set Power-on Password Select this choice to set or change a power-on password. For more information, see “Power-on password” on page 1 14. – Clear Power-on Password Sel[...]

password has access to only the limited Setup Utility menu; the user can set, change, and delete the power-on password, if the system administrator has given the user that authority . Power-on password If a power-on password is set, when you turn on the server , the system startup will not be completed until you type the power-on password. Y ou can[...]

RAID controllers The following table lists the various utilities available to configure RAID controllers before an operating system is installed. T able 15. RAID utilities RAID configuration utility Description Location Where to find more information EasyStartup RAID configuration utility v For use with all factory-supported RAID controllers v Auto[...]

1. After you turn on the power and when the computer is starting, you are prompted to press Ctrl + H when the following message is displayed: Copyright© LSI Logic Corporation Press <Ctrl><H> for WebBIOS 2. Select an adapter from the list. 3. Click Start . The main W ebBIOS utility interface is displayed. Y ou can toggle between the phy[...]

New Configuration Clears the existing configuration and lets you create a new configuration. Add Configuration Retains the existing storage configuration and adds new drives to it (this does not cause any data loss). 3. Click Next . 4. Select a configuration mode from the following options: Custom Configuration In this mode, you can control all att[...]

The EasyStartup program has the following features: v Self-booting DVD v Easy-to-use, language-selectable interface v Integrated help system v Automatic hardware detection v RAID configuration utility v Device drivers provided based on the server model and detected devices v Selectable partition size and file system v Support for multiple operating[...]

If you continue to the main program interface, you will have the following selectable options: v Compatibility notes: This selection provides information about the RAID controllers, operating systems, and server configurations supported by that version of the EasyStartup program. v User Guide: This selection provides information about the features [...]

– Integrated Mirroring Enhanced (IME) with hot-spare support (also known as RAID 1E) Use this option to create an integrated mirror enhanced array of three to eight disks, including up to two optional hot spares. All data on the array disks will be deleted. – Integrated Striping (IS) (also known as RAID 0) Use this option to create an integrate[...]

4. T o highlight the drive that you want to format, use the Up Arrow and Down Arrow keys. T o scroll left and right, use the Left Arrow and Right Arrow keys or the End key . Press Alt+D. 5. T o start the low-level formatting operation, select Format and press Enter . Creating a RAID array of hard disk drives T o create a RAID array of hard disk dri[...]

v Save response file: This task gives you the option of saving the information on a diskette or USB device as a response file for future installations on similarly configured Lenovo servers. v Start installation: This task starts the actual installation process. First, the disk is prepared using the disk and partition information you specified. The[...]

v SAS firmware is stored in ROM on the integrated RAID controller on the system board. v Major components contain vital product data (VPD) code. Y ou can select to update the VPD code during the UEFI code update procedure. The following items are downloadable at http://www .lenovo.com/support: v Diagnostic programs v IMM firmware v Ethernet firmwar[...]

The IMM supports the following basic system management features: v Environmental monitor with fan speed control for temperature, voltages, fan failure, power supply failure, and power backplane failure. v LED indicators to report errors that occur with fans, power supplies, microprocessor , hard disk drives, and system errors v DIMM error assistanc[...]

identify the server , and perform other management functions. Any standard T elnet client application can access the SOL connection. Using the remote presence capability and blue-screen capture The remote presence and blue-screen capture features are integrated functions of the integrated management module (IMM). These integrated functions allow yo[...]

2. On the Login page, type the user name and password. If you are using the IMM for the first time, you can obtain the user name and password from your system administrator . All login attempts are documented in the event log. Note: The IMM is set initially with a user name of USERID and password of P ASSW0RD (passw0rd with a zero, not a the letter[...]

v The server is not a domain controller . However , it is recommended to have the server join a domain. v The account that you use to log in and to install the Core Server has Administrator privileges on the server with full read/write access. Ideally , this account is also a Domain Administrator account. This account will be used to create the ini[...]

v ASP .NET v ASP v CGI v Server Side Includes v Windows Authentication v IIS 6 Metabase Compatibility Note: When you select ASP .Net or ASP , a dialog box displays the additional role services required. Click Add Required Role Services . 6. Click Install . Note: If IIS is already installed and certain Role Services are still required, expand Roles [...]

Chapter 8. T roubleshooting This chapter describes the diagnostic tools that are available to help you solve problems that might occur in the server . If you cannot diagnose and correct a problem by using the information in this chapter , see Appendix A, “Getting help and technical assistance,” on page 179 for more information. T roubleshooting[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(T rained[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(T rained[...]

Keyboard, mouse, or pointing-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v [...]

Memory problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded[...]

Microprocessor problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is [...]

Monitor problems Some monitors have their own self-tests. If you suspect a problem with your monitor , see the documentation that comes with the monitor for instructions for testing and adjusting the monitor . v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listi[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(T rained[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(T rained[...]

Power problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded [...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(T rained[...]

Software problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preced[...]

2. Check for loose cables in the power subsystem. Also check for short circuits, for example, if a loose screw is causing a short circuit on a circuit board. 3. Remove the adapters and disconnect the cables and power cords to all internal and external devices until the server is at the minimum configuration that is required for the server to start [...]

Solving undetermined problems If the diagnostic tests did not diagnose the failure or if the server is inoperative, use the information in this section. If you suspect that a software problem is causing failures (continuous or intermittent), see “Software problems” on page 140. Damaged data in CMOS memory or damaged firmware can cause undetermi[...]

v System-event log: This log contains all IMM, POST , and system management interrupt (SMI) events. Y ou can view the system-event log through the Setup Utility and through the Dynamic System Analysis (DSA) program (as the IPMI event log). The system-event log is limited in size. When it is full, new entries will not overwrite existing entries; the[...]

4. Click Downloads and drivers to download firmware updates. If IPMItool is installed in the server , you can use it to view the system-event log. Most recent versions of the Linux operating system come with a current version of IPMItool. Y ou can view the IMM event log through the Event Log link in the integrated management module (IMM) Web interf[...]

POST error codes When you turn on the server , it performs a series of tests to check the operation of the server components and some optional devices in the server . This series of tests is called the power-on self-test, or POST . If a power-on password is set, you must type the password and press Enter , when you are prompted, for POST to run. If[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded b[...]

Note: After you exit from the stand-alone memory diagnostic environment, you must restart the server to access the stand-alone memory diagnostic environment again. 5. Select gui to display the graphical user interface, or select cmd to display the DSA interactive menu. 6. Follow the instructions on the screen to select the diagnostic test to run. I[...]

T o save the DSA log to a file on a diskette or to the hard disk, click Save Log on the diagnostic programs screen and specify a location and name for the saved log file. Notes: 1. T o create and use a diskette, you must add an optional external diskette drive to the server . 2. T o save the test log to a diskette, you must use a diskette that you [...]

Appendix A. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This section contains information about where to go for additional information about Lenovo and Lenovo products, what t[...]

Calling for service During the warranty period, you can get help and information by telephone through the Customer Support Center . These services are available during the warranty period: v Problem determination - T rained personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the pro[...]

Service methods and procedures vary by country , and some services might not be available in all countries. International W arranty Service is delivered through the method of service (such as depot, carry-in, or on-site service) that is provided in the servicing country . Service centers in certain countries might not be able to service all models [...]

182 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Leno[...]

estimated through extrapolation. Actual results may vary . Users of this document should verify the applicable data for their specific environment. T rademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Lenovo logo ThinkServer The following terms are trademarks of International Business Machi[...]

Lenovo makes no representation or warranties regarding non-Lenovo products and services, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. These products are of fered and warranted solely by third parties. Some software might differ from its retail version (if available) and might not inclu[...]

L ’etiquette du système respecte la Directive européenne 2002/96/EC en matière de Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les dispositions de retour et de recyclage applicables aux systèmes utilisés à travers l’Union européenne. Conformément à la directive, ladite étiquette précise que le produit [...]

T able 17. Limits for particulates and gases (continued) Contaminant Limits 1 ASHRAE 52.2-2008 - Method of T esting General V entilation Air-Cleaning Devices for Removal Efficiency by Particle Size . Atlanta: American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. 2 The deliquescent relative humidity of particulate contamina[...]

Battery return program This product may contain a lithium or lithium ion battery . Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly . Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http:[...]

batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt récupérée en fin de cycle de vie selon cette norme. In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life. The label on the battery may also i[...]

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Class A emission compliance statement This Class A digital[...]

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG (früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über die elektromagnetische V erträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022 Klasse A ein. Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu i[...]

Japan V oluntary Control Council for Interference (VCCI) statement T aiwan Class A warning statement People’s Republic of China Class A warning statement Korea Class A warning statement 192 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide[...]

Index A acoustical noise emissions 1 1 adapter hot-plug devices 92 installing 57 hot-plug 92 PCI card installing 60 removing 55 requirements 57 scanning order 57 ServeRAID-MR10i 92 ServeRAID-MR10is installing 94 administrator password 1 13, 1 14 Advanced Settings Utility (ASU) program, overview 126 Advanced Settings Utility program, overview 126 AS[...]

diskette drive (continued) removing 44 display problems 135 documentation DVD 3 drive cables 54 removable-media 47, 48 drive bays, internal 43 drives bay 1, 2, or 3 installing 45 hot-swap SAS cabling 55 hot-swap SA T A cabling 55 hot-swap, removing 49, 51 Simple-swap SA T A cabling 55 simple-swap, removing 54 simple-swap, removing 53 DSA log 143, 1[...]

H H8 heartbeat LED 24 handling static-sensitive devices 31 hard disk drive diagnostic tests, types of 131 formatting 120 problems 130 status LED 17 hard disk drives hot-swap SAS or SA T A, installing 51 hot-swap SAS or SA T A, removing 49 simple-swap SA T A, installing 54 simple-swap SA T A, removing 53 hard-disk drive activity LED 17 heat output 1[...]

LEDs (continued) rear of server 18 LEDs and controls on the front of the server 15 logs system-event message 144 lower bezel installing 69 removing 34 LSI Configuration program 1 19 M management, systems 7 memory specifications 10 memory module installing 38 order of installation 42 memory modules removing 37 memory problems 133 menu choices in Set[...]

reliability 12 remote presence feature functions 8 using 125 removing adapter 55 battery 89 CD drive 44 connector 62 cover 32 DIMMs 37 diskette drive 44 DVD drive 44 fan hard disk drive, assembly 75 rear 73 fan sink 99 front USB connector assembly 84 front-panel assembly 83 hot-swap drives 49 hot-swap power supply cage 87 hot-swap SAS or SA T A dri[...]

system board (continued) removing 104 switches and jumpers 21 system reliability guidelines 30 system-board error LED 23 system-error LED 17 system-event log 143 system-information LED 17 system-locator LED 17 systems management 7 T tape drive installing 45, 48 remove 47 temperature 1 1 test log, viewing 177 tests, hard disk drive diagnostic 131 th[...]

[...]

Printed in USA[...]