LG Electronics IP LDK-20 manuel d'utilisation
- Voir en ligne ou télécharger le manuel d’utilisation
- 80 pages
- 4.8 mb
Aller à la page of
Les manuels d’utilisation similaires
-
Flat Panel Television
LG Electronics 32LG20
20 pages 7.86 mb -
Microwave Oven
LG Electronics LTM9000W
26 pages 0.27 mb -
Cell Phone
LG Electronics CU320
1 pages 0.26 mb -
Flat Panel Television
LG Electronics 32/37/42/47/55LD6***
289 pages 28.15 mb -
Air Conditioner
LG Electronics LAN121CNM
71 pages 7.26 mb -
Refrigerator
LG Electronics LRT 2232
33 pages 1.01 mb -
Car Satellite TV System
LG Electronics 32LE3
220 pages 18.18 mb -
Cell Phone
LG Electronics II
245 pages 2.59 mb
Un bon manuel d’utilisation
Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation LG Electronics IP LDK-20. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel LG Electronics IP LDK-20 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.
Qu'est ce que le manuel d’utilisation?
Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation LG Electronics IP LDK-20 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.
Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.
Donc, ce qui devrait contenir le manuel parfait?
Tout d'abord, le manuel d’utilisation LG Electronics IP LDK-20 devrait contenir:
- informations sur les caractéristiques techniques du dispositif LG Electronics IP LDK-20
- nom du fabricant et année de fabrication LG Electronics IP LDK-20
- instructions d'utilisation, de réglage et d’entretien de l'équipement LG Electronics IP LDK-20
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes
Pourquoi nous ne lisons pas les manuels d’utilisation?
Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage LG Electronics IP LDK-20 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles LG Electronics IP LDK-20 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service LG Electronics en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées LG Electronics IP LDK-20, comme c’est le cas pour la version papier.
Pourquoi lire le manuel d’utilisation?
Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif LG Electronics IP LDK-20, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.
Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation LG Electronics IP LDK-20. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.
Table des matières du manuel d’utilisation
-
Page 1
IP LDK-20 Installation Manual I I P P L L D D K K 2 2 0 0 INST ALLA TION MANUAL[...]
-
Page 2
IP LDK-20 Installation Manual R R E E V V I I S S I I O O N N H H I I S S T T O O R R Y Y ISSUE DATE CONTENT S OF CHANG ES REMARK ISSUE 1.0 ISSUE 1.1 2005.3 2005.5 Initial Release Add Expansion Modules and VMIBE/AAFBE[...]
-
Page 3
IP LDK-20 Installation Manual i T T A A B B L L E E O O F F C C O O N N T T E E N N T T S S ■ IMPORTANT SAFETY INSTRUCTIONS ... .................................................... 1 Safety re quirements ......................... ........................................................... ........................ ........ 1 ■ PRECAUTION .......[...]
-
Page 4
IP LDK-20 Installation Manual ii 4.1 Unp acking ............................ ................................................... ................................... .......... 47 4.2 Open ing an d closing the fron t cover ................ ............................................ ....................... 48 4.2.1 Openi ng the front cover ........[...]
-
Page 5
IP LDK-20 Installation Manual Introduction 1 ■ Important Safety Instructions Safety requirements When using your telephone equip ment, basic safety pre cautions should a lways be followed to redu ce the risk of fire, electric sh ock and oth er personal i njury, incl uding the fol lowing: • Please re ad and underst and all instr uctions. • Fol[...]
-
Page 6
IP LDK-20 Installation Manual Introduction 2 ■ Precaution • Keep the syst em away from heati ng applianc es and elect rical noise ge nerating devic es such as fluoresc ent lamps, motors a nd televisi ons. These noise s ources c an interfer e with the perf ormanc e of the IP LDK-20 System. • This syste m should be kept fr ee of dust, moisture [...]
-
Page 7
IP LDK-20 Installation Manual Introduction 3 ■ The Structure of Manual This install ation manu al is desi gned to provid e as gene ral inform ation for th e IP LDK-20 Sys tem. It provides instructio ns for installin g the hardware, and pro gramming the IP LDK-2 0 System using keys et. This manual cont ains the following sections: Section 1. I ntr[...]
-
Page 8
IP LDK-20 Installation Manual Introduction 4 SECTION 1. INTR ODUC TION 1.1 The IP LD K -20 Sy stem highlight s Features of the IP LDK-20 Syst em include: • Flexib le arch itecture • Opti onal LAN Interf ace • S table & en hanced voic e features • S imple install ation & effic ient system ma nagement - Remote admin th rough BRI conne[...]
-
Page 9
IP LDK-20 Installation Manual Introduction 5 1.3 System Components ITEM OPTION BO ARD DESCRIPTI ON KSU Key Service Unit PSU Pow er Supply Uni t, 90W MBUB Main Board Unit (2B RI, 4DKT , 2DKT/SLT, and 2S LT) CO boards Central Office Line interface boards (L COB, STIB,CBIB) Main Board EXT boards Extension boards (DTIB , SLIB) LCOB Loop Start CO Interf[...]
-
Page 10
IP LDK-20 Installation Manual Introduction 6 1.4 Specifications 1.4.1 General spec ifications ITEM DESCRIPTIO N SPECIF ICATION AC Voltage In put 230 +/-10% Volt AC @47-63Hz AC Pow er 90W AC Input F use 1.25A @ 25 0Volt A C PSU DC Output Voltag e +5, -5, +30Volt DC AC Voltage In put 230 +/-10% Volt AC @47-63Hz AC Input Fuse 1A @ 250V olt AC AC Adapt[...]
-
Page 11
IP LDK-20 Installation Manual Introduction 7 1.4.2 System Capacity DESCRIPT ION CAPACITY /BOARD TOTAL Time Slots 96 CO Line Port s 4/MBUB(BRI) 4/LCOB or 4/STIB 8/VOIM Max. 16 (Analog CO, ISDN BRI and/or IP tr unk) Max direct Station connec tions 8/MB UB 8/DTIB or 8/SLIB 8/DTIM, 8 SLIM, or 8/VOIM Max. 24 Max LAN po rt 1/LANU 1 Max MODEM Channel 1/MO[...]
-
Page 12
IP LDK-20 Installation Manual KSU Insta llation 8 SECTION 2. KSU INSTALLATION 2.1 Pre-Inst allation Please read the f ollowing guid elines conc erning inst allation an d connecti on before installi ng the IP LDK-20 System. Be sure also to comply with applica ble local regulations. 2.1. 1 Safe ty ins t allati on in structi ons When inst alling t he [...]
-
Page 13
IP LDK-20 Installation Manual KSU Insta llation 9 2.2 KSU Inst allation 2.2.1 Unpacking Open the box and verify the items shown i n Figure 2.2.1 are included: Figure 2.2.1 Unp acking Key service uni t Tie cable Anchor plug Scre w Fuse Power cord Mounting template Battery cable Manual[...]
-
Page 14
IP LDK-20 Installation Manual KSU Insta llation 10 2.2.2 KSU exterior and dimension Figure 2. 2.2 shows t he exterio r and dim ensions of the KSU: Figure 2.2.2 KSU exterior and dimension[...]
-
Page 15
IP LDK-20 Installation Manual KSU Insta llation 11 2.2. 3 KS U wi t h e x p a nsion m o du l e exterio r and dim en sion Figure 2. 2.3 shows t he exterio r and dim ensions of the KSU: Figure 2.2.3 KSU with expan sion module exterior and di mension[...]
-
Page 16
IP LDK-20 Installation Manual KSU Insta llation 12 2.2.4 Opening and closing the front cover 2.2.4.1 Opening the front cover 1. Turn the scre w counter-cl ockwise to loos en as shown i n Figure 2.2. 4.1. 2. Lift the front cover in the direction of the arrow as shown: Figure 2.2.4. 1 Openi ng the front co ver[...]
-
Page 17
IP LDK-20 Installation Manual KSU Insta llation 13 2.2.4.2 Closing the front cover Insert the fr ont cover into the s lot on the KS U as show in Fig ure 2.2.4.2. Then put the f ront cover down on th e KSU in the di rection of the arr ow, as shown. Turn the screws clockwis e to tighten, as in the Figure. Figure 2.2.4.2 Cl osing th e front co ver ※[...]
-
Page 18
IP LDK-20 Installation Manual KSU Insta llation 14 2.2.5 Frame ground connection It is very important th e frame of the IP LDK-2 0 system is grounded: 1. Tu rn the screw counter-clo ck wise to loosen. Then insert the gro unding wire. 2. Tighten the screw. Th en connect the groundi ng wire to grou nd source as shown in Figur e 2.2.5. Figure 2.2.5 Gr[...]
-
Page 19
IP LDK-20 Installation Manual KSU Insta llation 15 2.2. 6 Po wer Supply Unit (PSU) installation Before install ation, make su re that the KSU not p lugged int o an outlet. T he PSU is locate d at the left-most ar ea of the KSU, and is capabl e of providi ng three ki nds of power sou rces to MBUB thro ugh the 7PIN connec tor, CN19 (ref er to the fol[...]
-
Page 20
IP LDK-20 Installation Manual KSU Insta llation 16 2.2.7 External backup batteri es installation In case of powe r failure, the e xternal bac kup batteries automaticall y maintain un interrupted p ower for th e IP LDK-20 system. The ext ernal batteries must provide 24 Volts DC. This is gener ally accomp lished by connecti ng two 12 Volt batteri es [...]
-
Page 21
IP LDK-20 Installation Manual KSU Insta llation 17 2.2.8 KSU mounting 2.2.8.1 Wall mounting 1. Install 3 anchor pl ugs in the wall usin g the mounting templ ate included for accu rate plac ement (Fig ure 2.2.8.1a). 2. Attach the mou nting template with the incl uded 3 scre ws. 3. Hook the KSU ont o the scre ws, making sure that the system sli des d[...]
-
Page 22
IP LDK-20 Installation Manual KSU Insta llation 18 Figure 2.2.8. 1b KSU Wall Mounti ng ※ Note : Be careful not to drop the KSU.[...]
-
Page 23
IP LDK-20 Installation Manual KSU Insta llation 19 2.2.8.2 Rack mounting 1. Attach the rac k bracket to the bot tom of the IP LDK-20 syste m as shown in Figu re 2.2.8.2a, a nd attach it to the system sec urely by tighteni ng the sc rews cl ockwise. Figure 2.2.8. 2a Rack Brac ket 2. To attach the IP LDK-20 system to the rack, affix t he bracket with[...]
-
Page 24
IP LDK-20 Installation Manual Board Installation 20 SECTION 3. BOARD INSTALLATION 3.1 Inst allatio n of the Boards Prior to Boar d Installation, the following s hould be cons idered: CAUTI ON • Power must be turned OFF. • To protect the system from static electricity , do not touch th e boards. To di scharge static, touch a grounded object, or [...]
-
Page 25
IP LDK-20 Installation Manual Board Installation 21 3.2 MBUB (Main Board Un it) Descript ion The MBUB controls co mmunication between the pe ripheral interfaces, supervises all resour ces in the system, controls the g ain adjustment of the PCM signal, generates the system tones, and ma nages system call processing . The MBUB (Fig ure 3.2a) inc orpo[...]
-
Page 26
IP LDK-20 Installation Manual Board Installation 22 Figure 3.2b Connection The MBUB is inst alled in the KSU a nd provi des various k inds of conn ectors and RJ 45 modular j acks for the connection of peripher al boards an d miscell aneous func tions (r efer to the f ollowing Table ). Connector/Modular Jack/S w itch Functions SWITCH/ CONNECTOR FUNC[...]
-
Page 27
IP LDK-20 Installation Manual Board Installation 23 3.2.1 Modular Jack(MJ1~MJ3) Pin Assignment 3.2.1.1 MBUB MJ1(CO) T Mode CONNECTOR PI N NUMBER NO SIGNAL NAME FUNCTION 1,2,7,8 Rese rved 3 TX+ Transmit Data 4 RX+ Receive Data 5 RX- Receive Data RJ45 6 TX- Transmit Data Figure 3.2.1. 1a T Mode(Basic BRI Line Conn ector and Termin ating Resistors) NT[...]
-
Page 28
IP LDK-20 Installation Manual Board Installation 24 S Mode CONNECTOR PI N NUMBER NO SIGNAL NAME FUNCTION 1,2,7,8 Rese rved 3 RX+ Receive Data 4 TX+ Transmit Data 5 TX- Transmit Data RJ45 6 RX- Receive Data Figure 3.2.1.1b S Mode(Basic BRI Line Connector and Termin ating Resistors) SW5 and SW6 : 1,2 Pin Setting(The Defaul t = All On Position) TERM I[...]
-
Page 29
IP LDK-20 Installation Manual Board Installation 25 - CN21: SET FOUR 2PIN J UMPERS AS SHOW N IN THE AB OVE TABLE ACCOR DING TO EACH MO DE. 3.2.1.2 MBUB MJ2 & MJ3(Extension) MBUB MJ2 (EXTENSION) CONNECTOR PIN NUMBE R NO SIGNAL NAME 1,2,3 Reserv ed 4,5 DKT-R, DKT-T RJ45 6,7,8 Reserv ed MBUB MJ3-1 , 2 (EXTENSION) CONNECTOR PIN NUMBE R NO SIGNAL NA[...]
-
Page 30
IP LDK-20 Installation Manual Board Installation 26 5-6 RESE RVED 3.2.1.3 MJ4 Pin Assignment MBUB CONNECTOR PIN NUMBE R NO SIGNAL NAME 1,2 Relay 1-R, Relay1-T 3,4 Relay 2-R, Relay2-T 5,6 EXT_PAGE-R, EX T_PAGE-T RJ45 7,8 Ala rm-R, Alarm-T 3.2.1.4 SW3 Functions and LED Indications SWITCH FUNCTION OFF ON(DEFAUL T) 3-1 Admi nist ration P rogrammi ng Ac[...]
-
Page 31
IP LDK-20 Installation Manual Board Installation 27 GREE N IN-USE 3.2.1.5 CN22 Pin assignment MBUB CONNECTOR P IN NUMBER NO SIGNAL NAME FUNCTION 1 RESERVED 2 TD Transmitted Data 3 RD Received Data 4 DSR Not used 5 SG Signal Ground 6 DTR Not used 7 CTS Not used 8 RTS Not used RS-232C 9 RESERVED PC CONNECTOR P IN NUMBER NO SIGNAL NAME FUNCTION 1 RESE[...]
-
Page 32
IP LDK-20 Installation Manual Board Installation 28[...]
-
Page 33
IP LDK-20 Installation Manual Board Installation 29 3.3 Inst allation of the CO Line Boa rd BOARD PORT CON NECTOR TYPE DESCRIPTIO N CABLE RE MARK LCOB 2 ports (4 LCO) RJ45 Loop Start CO Li ne Interf ace 2 wire STIB 2 ports (2 BRI) RJ45 ISDN Basic Rat e Interface (2B+ D) 4 wire Switched T or S CBIB 2 p orts ( 1 BRI+2 LCO) RJ45 ISDN Basic Rate Interf[...]
-
Page 34
IP LDK-20 Installation Manual Board Installation 30 3.3.1.1 Pin Assignment LCOB CONNECTOR PIN NUMBE R NO SIGNAL NA ME 1,2 C O-R , CO-T 3 Res erv ed 4,5 C O-R , CO-T RJ45 6,7, 8 Re ser ve d CONNECTOR FUN CTIONS CONNECTOR FUNCTION REMARK CN2 and CN3 PRCPTU4 or PRU4 conn ection CN1, CN2 and CN3 CPCU4 conne ction MJ1 2 ports RJ45 type CO line con necti[...]
-
Page 35
IP LDK-20 Installation Manual Board Installation 31 PRCPTU4 (PR and CPT detection Unit) Descripti on The PRCPTU4 c an be optional ly mounted on LCO B, and pr ovides f our polarity rev ersal dete ction for call met ering, four call pro gress tone d etection t o support ACNR featur e (Automatic Called Num ber Redial ). Figure 3.3.1. 2b PRCPTU4 CPCU4 [...]
-
Page 36
IP LDK-20 Installation Manual Board Installation 32 3.3.2 STIB (Basic Rate Interface Board: Selectable S/ T interface) Descript ion STIB should be install ed on t he LCOB/STI B/CBIB connec tor, and s upports T- interface or S-interfac e. The 1s t BRI port can be operat ed to T-mode and S-mod e and the 2nd port can onl y be set to T-mode. Figure 3.3[...]
-
Page 37
IP LDK-20 Installation Manual Board Installation 33 3.3.2.1 Pin assignment T MODE CONNECTOR PI N NUMBER NO SIGNAL NAME FUNCTION 1,2,7,8 Rese rved 3 TX+ Transmit Data 4 RX+ Receive Data 5 RX- Receive Data RJ45 6 TX- Transmit Data Figure 3.3.2.1a T Mode(Basic STIBI Line Connector and Termi nating Resistors) NT1(NT - BOX ) 3 6 4 5 RX+ RX - TX+ TX STI [...]
-
Page 38
IP LDK-20 Installation Manual Board Installation 34 S MODE CONNECTOR PI N NUMBER NO SIGNAL NAME FUNCTION 1,2,7,8 Rese rved 3 RX+ Receive Data 4 TX+ Transmit Data 5 TX- Transmit Data RJ45 6 RX- Receive Data Figure 3.3.2.1b S Mode(Basi c STIBI Lin e Connector and Terminating Resistors) LED INDIC ATIONS STATUS LED ON OFF LINE NO. REMARK RED ERROR LED1[...]
-
Page 39
IP LDK-20 Installation Manual Board Installation 35 3.3.2.2 Line Connector and Terminating Resistors SW 1 AND S W4’S 1, 2 P IN SETTING : DE FAULT = ALL ON POS ITION TERM INAT I NG R ESI ST O R S LINE NO RJ45 TYPE JACK SWITCH PIN1, 2 ON PIN3, 4 OFF REMARK Line 1 MJ1 SW4 Terminati on Open Line 2 MJ1 SW1 Terminati on Open T OR S SW ITCH SE T T ING S[...]
-
Page 40
IP LDK-20 Installation Manual Board Installation 36 3.3.3 CBIB (CID Loop Start CO line + Basic Rate Interface Board) Descript ion The CBIB can be installe d on the LCOB/STIB/CBIB connector, and provides 2 CO/P BX Loop Start CO Line int erfaces that suppor t pulse/DTMF signal and ISDN BRI T-mode in terface. CO Inte rface contains r ing and loop curr[...]
-
Page 41
IP LDK-20 Installation Manual Board Installation 37 3.3.3.1 Pin Assignment CBIB 1’ST PORT FOR BRI T-MODE CONNECTOR PI N NUMBER NO SIGNAL NAME FUNCTION 1,2,7,8 Rese rved 3 TX+ Transmit Data 4 RX+ Receive Data 5 RX- Receive Data RJ45 6 TX- Transmit Data CBIB 2’ ND PORT FOR L CO CONNECTOR PIN NUMBE R NO SIGNAL NA ME 1,2 C O-R , CO-T 3 Res erv ed 4[...]
-
Page 42
IP LDK-20 Installation Manual Board Installation 38 3.3.3.2 Add-On Boards PRU2 (Polarity Reversal de tection Unit) Description The PRU2 can be optionally m ounted on CBI B, and provid es Polarit y Revers al detection fo r call meter ing. It also provide s four on-hook conn ection paths for SMS. PRCPTU2 (PR and CPT detection Unit) Description The PR[...]
-
Page 43
IP LDK-20 Installation Manual Board Installation 39 3.4 Inst allat ion of the Extension Board BOARD PORT CON NECTOR TYPE REMA RK DTIB4 4 DKT ports RJ45 Digita l Terminal In terface : 4 ports DTIB8 8 DKT ports RJ45 Digita l Terminal In terface : 8 ports SLIB4 4 SLT ports RJ45 Si ngle line telephone In terface : 4 ports SLIB8 8 SLT ports RJ45 Si ngle[...]
-
Page 44
IP LDK-20 Installation Manual Board Installation 40 3.4.2 DTIB8 (Digital Terminal I nterface Board) Description DTIB8 can be insta lled on the SLIB/DT IB connect or, and p rov id es 8 Digit al Keyset p orts. It als o provides 2-wire connections to D igital Keys ets. It has modul e connect ors, MJ1 and MJ2, t hat are us ed to connect Di gital Keys e[...]
-
Page 45
IP LDK-20 Installation Manual Board Installation 41 3.4. 3 SLIB 4 (Sing le Line Interf ace Boar d) Description SLIB4 can be installed o n the SLIB/DTIB c onnector, an d provides 4 SLT ports, an d 2 DTMF receivers. The SLIB4 and SLT are conn ected with a RJ45 Mod ular Jack, MJ3. Figure 3.4.3 S LIB4 3.4.3.1 Pin assignment SLIB4 CONNECTOR PI N NUMBER [...]
-
Page 46
IP LDK-20 Installation Manual Board Installation 42 3.4. 4 SLIB 8 (Sing le Line Interf ace Boar d) Description SLIB8 can be installed t he SLIB/ DTIB connector, and p rovides the 8 SLT ports and 2 DTMF rec eivers. T he SLIB8 and SLT are conn ected wit h a RJ45 Modul ar Jack, MJ 2 & MJ3. Figure 3.4.4 S LIB8 3.4.4.1 Pin assignment SLIB8 CONNECTOR[...]
-
Page 47
IP LDK-20 Installation Manual Board Installation 43 3.5 Other Boar d Installations 3.5.1 VMIBE ( Voice Mail Inter face Board Enhanc ed) Description The VMIBE can be installed on the VMIB/AAFB connec tor, and pro vides system announcemen t, ACD/UCD announceme nt, and Use r Greeting. Fig ure 3. 5.1 V MI BE ITEM RECORD/P LAY MOH Channel 3 channels 1 c[...]
-
Page 48
IP LDK-20 Installation Manual Board Installation 44 3.5.2 AAFBE(Auto Attendant Function Board Enhanced) Description The AAFBE can be installe d on the VMIB/AAFB connector, an d provides syst em announcem ent and ACD/UCD announcement. Figure 3.5.2 AAFBE ITEM RECORD/PLAY MOH Channel 3 channels - Max record time: Sys tem /t ime s ta mp User re cord ti[...]
-
Page 49
IP LDK-20 Installation Manual Board Installation 45 3.5.3 LANU (LAN interface Unit) Description LANU shoul d be installe d on the LANU conn ector, and pr ovides 1 LAN p ort of 10Base-T networki ng. RJ45 Mod ular Jack, MJ1, is used to interface wi t h the Wide Area Netw ork (WAN) or PC, and has two LED s that indicate the operati onal state of the L[...]
-
Page 50
IP LDK-20 Installation Manual Board Installation 46 3.5.4 MODU (MODEM function Unit) Description MODU shoul d be installe d on the MODU con nectors , and provid es an analo g modem connect ion. It s upports Bell, ITU-T, V.34, V.32BIS, V.90 Prot ocol at 3 00bps, up t o 33Kbps sp eed rate, an d automatic r ate negoti ation. Figure 3.5.4 MODU[...]
-
Page 51
IP LDK-20 Installation Manual Board Installation 47 SECTION 4. EXPANSION MODULE INSTALLATION IPLDK-20 pr ovides t hree kinds of expans ion modul es, VOI M, DTIM and S LIM. MODUL E PORT CON NECTOR TYPE DESCRIPTION CABLE REMARK VOIM 1 port RJ45 Voic e Over I nternet Protoc ol interf ace 4 wire SLIM 4 ports RJ45 Single Li ne Telepho ne interf ace: 8 S[...]
-
Page 52
IP LDK-20 Installation Manual Board Installation 48 4.2 Opening an d closing t he front cover 4.2.1 Opening the front cover 1. Turn the scre w counter-cl ockwise to loos en as shown i n Figure 4.2. 1. 2. Lift the front cover in the direction of the arrow as shown: . Figure 4.2.1 Op ening the front co ver[...]
-
Page 53
IP LDK-20 Installation Manual Board Installation 49 4.2.2 Closing the front cover 1. Insert the front cover into the slot on a modul e as show in Figure 4. 2.2. 2. Then put the front cover down on a modul e in the directio n of the arrow, as shown. 3. Turn the screws cl ockwise to t ighten, as in t he Figure. Figure 4.2.2 Cl osing the front co ver [...]
-
Page 54
IP LDK-20 Installation Manual Board Installation 50 4.3 Opening and c losi ng the front cover 4.3.1 Connecting Expansion Module to KSU 1. Insert the expansi on module into t he slot of bas ic KSU as sho w in Figure 4.3. 1. 2. Turn the screws cl ockwise to t ighten, as i n the Figure. Figure 4.3.1 Connectin g an expansion module[...]
-
Page 55
IP LDK-20 Installation Manual Board Installation 51 4.3.2 Wall mounting The KSU with an ex pansion mo dule is mount ed on the wall in the sam e way with basic KS U and an expans ion module itself is not mounted on the wall as shown in Figure 4.3.2. Figure 4.3.2 Wall mounting of KS U with an expan sion module ※ Note : Be careful not to drop the KS[...]
-
Page 56
IP LDK-20 Installation Manual Board Installation 52 4.3.3 Rack Mounting 1. Attach the rack bracket t o the bottom of an ex pansion module as sh own in Figur e 4.3.3.1. Figure 4.3.3.1 Rack bracket 2. Attach it to an modul e securely by t ightenin g the screws clockwise, a s in the Figu re. Figure 4.3.3.2 Tightening Rack bracket[...]
-
Page 57
IP LDK-20 Installation Manual Board Installation 53 3. To attach an expansi on module t o the rac k, affix t he bracket with the 4 s crews prov ided (Fig ure 4.3.3. 4). 4. Connect an e xpansion m odule with the b asic KSU by a f lat ca ble packed in t he pac kage type2, as in the Fi gure. Figure 4.3.3.4 Modu le Rack Mounting ※ Note: The flat cabl[...]
-
Page 58
IP LDK-20 Installation Manual Board Installation 54 4.4 External backup batteries connection In case of powe r failure, the e xternal bac kup batteries automaticall y maintain un interrupted p ower for th e IP LDK-20 system. The ext ernal batteries must provide 24 Volts DC. This is gener ally accomp lished by connecti ng two 12 Volt batteri es in a[...]
-
Page 59
IP LDK-20 Installation Manual Board Installation 55 4.5 VOIM (V oice over Internet Prot ocol Interface Modu le) inst allation Descript ion The VOIM can be instal led on the basic KSU and provides the Ethern et interface f or S/W applicatio ns and VoIP features with optional VoIP daughter bo ard. The VOIM has the capacity for maximum 8 channels with[...]
-
Page 60
IP LDK-20 Installation Manual Board Installation 56 Figure 4.5.2 VOI B The VOIB is instal led in the VOIM and provide s various kinds of connector s and RJ45 modular jacks for the connection of peripher al boards an d miscell aneous func tions (r efer to the f ollowing Table ). Various switches and connectors functions Switch / Connector Functions [...]
-
Page 61
IP LDK-20 Installation Manual Board Installation 57 LED indications LED Functions Remark LD1 DSP HINT int errupt LED (ON: A ctive, OFF: Idle) LD2 Periodic toggl e – ON: 1 sec., OFF: 1 sec. LD3 Chan nel8 Seize i ndicatio n LED (ON: Bus y, OFF: Idle) LD4 Chan nel7 Seize i ndicatio n LED (ON: Bus y, OFF: Idle) LD5 Chan nel6 Seize i ndicatio n LED (O[...]
-
Page 62
IP LDK-20 Installation Manual Board Installation 58 4.5.2 VOIU(Voice over Internet Protocol Interface Unit) Descript ion The VOIU can b e installed o n the VOIB thro ugh CN2 and C N3 and provi des the Eth ernet inte rface for S/W applications an d 4 VoIP channels. Figure 4.5.2. 1 VOIU Installation[...]
-
Page 63
IP LDK-20 Installation Manual Board Installation 59 4.6 SLIM(SL T Interfac e Module) Installation Descript ion The SLIM provides the ei ght (8) ports of SLT interfac e and two DTMF receive rs. The connection bet ween the SLIM and Singl e Line Tel ephone is performed t hrough RJ 45 Modula r Jacks, MJ1. SLIM can be inst alled on bas ic KSU. Figure 4.[...]
-
Page 64
IP LDK-20 Installation Manual Board Installation 60 4.7 DTIM(Digit al T erminal Interface Module) Descript ion The DTIM provid es Digit al terminal i nterface of 8 ports . It also provides 2 -wire conn ection to Digital K eysets. It has module connec tors, MJ1, whic h is used to c onnect Di gital Keyset li nes to the DTI M. DTIM can be installed on[...]
-
Page 65
IPLDK-20 Installation Manual Te rmina l Co nnect ion 61 SECTION 5. TE RMINAL CONNECTION 5.1 T erminal Models Various types of digit al terminals are used with IP LDK-20 MBUB/DTIB4/DTIB 8 as listed and shown below: MODEL DESCRIPTION LDP-7004N 8 Flexible Button Normal LDP-7004D 4 Flexible Button Disp lay LDP-7008D 8 Flexible Button Disp lay LDP-7016D[...]
-
Page 66
IPLDK-20 Installation Manual Te rmina l Co nnect ion 62 5.2 T erminal C abling D istan ce Figure 5.2 Termi nal Cabling Distance[...]
-
Page 67
IPLDK-20 Installation Manual Te rmina l Co nnect ion 63 5.3 Keyset Connection 5.3. 1 Digit al Key set The following illustrates how to conne ct the Digital Keyset to your system: Figure 5.3.1 Digital Keyse t Connection 5.3.1.1 Pin Assignment CONNECTOR TY PE PIN NUMBE R NO SIGNAL N AME 1-2 RESERV ED 3 TIP 4 RING RJ11 5-6 RESERV ED 5.3. 2 S L T The f[...]
-
Page 68
IPLDK-20 Installation Manual Te rmina l Co nnect ion 64 5.4 Connecting Additional T erminals MBUB provides c onnections for 1 external music so urce, 1 external page port, 2 relay cont acts, and an alar m/door- bell input monitor through the PJ1 audio jack and a MJ4 RJ45 Mod ular Jack. Figure 5.4.1 Additional T erminal Connection 5.4. 1 Ext e rnal [...]
-
Page 69
IPLDK-20 Installation Manual Starting the IP LDK-20 System 65 SECTION 6. STARTING THE IPLDK-20 SYSTEM 6.1 Before S t arting t he IP LDK -20 System The DIP switch (SW1 ) of Memory Back up Battery sh ould be t urned ON befo re install ing the MB UB, to protect system data in the case of a power failur e. To prepa re for prepro gramming, pe rform the [...]
-
Page 70
IPLDK-20 Installation Manual Starting the IP LDK-20 System 66 6.2.1.1 Button explanation There are ma ny kinds of DK TUs capable of c onnectin g to the IP LDK-20 s ystem. Figure 6.2.1 sho ws a model of the LDP-7024D and illustrates e ach button. Detailed DKTU information for this and other keysets is describ ed in the DKTU User G uide and Installa [...]
-
Page 71
IPLDK-20 Installation Manual Starting the IP LDK-20 System 67 6.2.2 Entering programming mode To enter Programming Mode, perform th e following Steps: Lift the handset OR Pre ss the [MON] button on the ADMI N station, and hear ICM di al tone. 1. Press the [TRANS/P GM] button a nd dial * # . 2. Confirmation t one shoul d be hear d. 3. Enter the AD[...]
-
Page 72
IPLDK-20 Installation Manual Starting the IP LDK-20 System 68 6.2.3 Pre-programming Location PGM-Na tion Code & Site Name (PGM10 0) ※ NOTE : The 4th pole of the DI P switch (SW 3) on the MPB must be turned ON. Procedure Nation Code To program the Nation code, perform the foll owing Steps: 1. Pres s [Trans/PGM] + PGM N u m ber(100), then [Flex[...]
-
Page 73
IPLDK-20 Installation Manual Starting the IP LDK-20 System 69 International Calling Codes NATION CODE NATI ON CODE NATION CODE America 1 Argentina 5 4 Australia 61 Bahrain 973 Banglade sh 880 Belgiu m 32 Bolivia 591 Bra zil 55 Brunei 673 Burma 95 Cameroon 237 Chile 56 China (Ta iwan) 886 CIS 7 Colombia 57 Costa Ric a 506 Cyprus 357 Czech 42 Denmark[...]
-
Page 74
IPLDK-20 Installation Manual Starting the IP LDK-20 System 70 6.2.3.1 RACK SLOT ASSIGNMENT (PG M 101) 1. Pres s [Trans/PGM] + 101 2. Enter slot number(2 digits ). 3. Pres s [ FLEX1 ] 4. Enter Board T ype code( 2 digits). Press [HO LD/SAVE] to accept change. STA CODE COL CODE STA & COL CODE Etc CODE DTIB4 DTIB8 SLIB4 SLIB8 11 12 13 14 LCOB2 LCOB[...]
-
Page 75
IPLDK-20 Installation Manual Starting the IP LDK-20 System 71 6.2.3.3 Numbering Plan Type (PGM 104) PROC ED UR E 1. Pres s [Trans/PGM] + 104 , then enter the Number Plan Type (Refer to following Table, press 1 digit ). Press [HO LD/SAVE] to accept change. Number Plan Type NUMBER SET TYPE / PRESS # I NTERCOM RANGE DEFAULT REMARK 1 10 – 3 7 Yes As [...]
-
Page 76
IPLDK-20 Installation Manual Starting the IP LDK-20 System 72 6.2.3.4 FLEXIBLE NUMBERING PLAN (PGM 105) PROC ED UR E To set your flexible numbering plan, perform the fo llowing Steps: 2. Pres s [Trans/PGM] + 105 , then enter the stat ion range (dial start and end s tation n umbers). Press [HO LD/SAVE] to accept change Numbering Plan D etail STATION[...]
-
Page 77
IPLDK-20 Installation Manual Starting the IP LDK-20 System 73 6.2.3.5 Flexible Numbering Plan (PGM 106-107) PROC ED UR E Plan A (106 ) 1. Pres s [Trans/PGM] + 106 , then press th e Flexible Button you wish to program (1-24). Enter the c ode (ref er to follo wing Tabl e). Press [HO LD/SAVE] to accept change. Flex Numberi ng Plan A(PGM 106) FLEX ITEM[...]
-
Page 78
IPLDK-20 Installation Manual Starting the IP LDK-20 System 74 Flex Numb ering Plan B (PGM 107) FLEX ITEM DEFAULT VALUE (AT NUMBER ING PLAN TYPE 1 ) 1 Alarm Reset 565 2 Group Call Pick-Up 566 3 UCD Group DND 568 4 Night Ans wer 569 5 Call Park Location Range 601 – 608 6 Direct Call Pick-Up 7 7 Access C O Line Group 801 – 808 (8 + CO Group N umbe[...]
-
Page 79
IPLDK-20 Installation Manual Starting the IP LDK-20 System 75 6.2.3.6 IP setting for System (PGM 108) PROC ED UR E IP Name (Use the # to skip) 1. Pres s [Trans/PGM] + 108 , then press [FLEX1]. Enter the c ode ( max. 16 c haract ers). Press [HO LD/SAVE] to accept change. Server IP Address 1. Pres s [Trans/PGM] + 108 , then press th e [ FLEX2 ] butto[...]
-
Page 80
IP LDK-20 Installation Manual Troubleshooting 76 SECTION 7. T ROUBLESHOOTING PROBLEM CAUSE / SYMPTOM SOLUTION Power short cir cuit in some board (s) Sys tem po wer f ail ur e LD6 LED lig ht on the MBUB is OFF or blinking Exchange the ma lfunctioning board for on e in good working condition. Dust each bo ard. Check the PSU fuse. Replace the PSU with[...]