Français dropdown-ico

Makita 2030S manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Makita 2030S. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Makita 2030S ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Makita 2030S décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Makita 2030S devrait contenir:
- informations sur les caractéristiques techniques du dispositif Makita 2030S
- nom du fabricant et année de fabrication Makita 2030S
- instructions d'utilisation, de réglage et d’entretien de l'équipement Makita 2030S
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Makita 2030S ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Makita 2030S et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Makita en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Makita 2030S, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Makita 2030S, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Makita 2030S. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    312 mm (12-9/32") MODEL 2030s Auto feed Manual feed Auto feed Manual feed No load speed (RPMI 9,000 INSTRUCTION MANUAL Cutting width Max. cutting depth Feed rateimin Imml Imml lml 3.0 (118") for stock 0 - 150 (0'' ~ 5-29132"1 wide 1 5 (1/16"1 for stock 150 ~~ 240 15-29/32" ~ 9-7/16"] wide 1.0 13/64'] for[...]

  • Page 2

    For Your Own Safety Read Instruction Manual Before Operating Planer-Jointer GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar to it. 2. KEEP GUARDS IN PLACE and in working order. 3. REMOVE ADJUSTING[...]

  • Page 3

    16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and namepl[...]

  • Page 4

    VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T[...]

  • Page 5

    FOR JOINTER 1. Maintain the proper relationships of infeed and outfeed table surfaces and cutterhead blade path. 2. Do not perform jointing operations on material shorter than 140 mm (5-1/2 inches), narrower than 19 mm (3/4 inch), or less than 12.7 mm (112 inch) thick. 3. Do not perform planing operations on material shorter than 140 mm (5-1/2 inch[...]

  • Page 6

    Movement and transport of planer-jointer When moving the tool, hold it as shown in the figure. When transporting it by vehicle, secure with a rope or other substantial means to prevent tipping or movement. Positioning the planer-jointer Locate the tool in a well lit and level place where you can maintain good footing and balance. Bolt it to the wor[...]

  • Page 7

    AUTO-PLANER FUNCTIONS: Dimensional adjustment Raise the table by turning the crank handle clockwise until the indicator plate points to the scale graduation indicating the de- sired finished dimension. One full turn of the crank handle moves the table 2 mm (3/32") up or down. The scale has inch graduations on its right side and metric graduati[...]

  • Page 8

    Operation Determine the depth of cut as described before. Insert the workpiece flat on the table top. When cutting a long or heavy workpiece, lift up its end slightly at the start and the end of the cut to avoid goug- ing or sniping at the extreme ends of the work p i ece. 3 Two rollers are provided on top of the tool to enable quick, effotless ret[...]

  • Page 9

    JOINTER FUNCTIONS: Extension support table The extension support table is convenient for cutting long workpieces. Install it on the outfeed table and semi-tighten the four hex bolts. Extend the legs and hook the arms over the screw using the hook (A). Then tighten the screws securely. Adjust the table height using the knobs so that the extension su[...]

  • Page 10

    Adjusting the fence angle I ClamD screw (A) 7 Hex bolts (A) The fence angle can be adjusted at any angle from 0’ to 45’. Loosen the clamp screws (A) and (B) and pull the fence out slightly. Then tighten the clamp screws (A) and (B). Loosen the hex bolts (A) and (B) and tilt the fence according to your work. Then tighten the hex bolts (A) and (B[...]

  • Page 11

    Beveling To cut a bevel, set the fence at the required angle and run the workpiece across the blades while keeping it firmly against the fence and tables. Carefully maintain flush, steady con- tact with the fence while making the cut. REPLACING THE PLANER BLADES Dull blades can cause a rough finish, an overload of the motor and dangerous kickback o[...]

  • Page 12

    AUTO-PLANE R 1. Removing the blades Loosen the hex bolt which secures the chip cover and open the chip cover. Open the safety cover over the jointer and rotate the drum by turning the knob until the drum can be locked in the position whereby the blade installa- tion bolts face upward. The magnetic holder has a different shaped claw on each side. Us[...]

  • Page 13

    2. Installing the blades Provide a flat wood block approx. 300 mm (1 1-13/16") long and 100 mm (3-15/16") wide. Place the blade and set plate on the wood block so that the blade locating lug of the set plate rests in the groove of the blade. Adjust the set plate so that both ends of the blade protrude approx. 1 mm (3/64") beyond the [...]

  • Page 14

    Install the other blade as described above. Rotate the drum slowly while pressing the lock plate to make sure there is nothing abnormal. Then close the chip cover and secure using the hex bolt. CAUTION : 0 Do not tighten the blade installation bolts without the blade locating lug of the set plate correctly resting in the groove of the blade. This m[...]

  • Page 15

    JOINTER 1. Removing the blades CAUTION : Always close the chip cover over the auto-planer before removing the blade. Lower the infeed table fully by turning the depth adjusting knob clockwise. Loosen the hex bolt which secures the safety cover rod and lift off the safety cover. Set the fence angle at 0' and push the fence fully toward the auto[...]

  • Page 16

    2. Installing the blades Provide a flat wood block approx. 150 mm (5-29/32") long and 100 mm (3-1 5/16") wide. Place the blade and set plate on the wood block so that the blade locating lug of the set plate rests in the groove of the blade. Adjust the set plate so that both ends of the blade do not protrude from the ends of the set plate.[...]

  • Page 17

    Lock the drum in the position whereby the blade edge faces upward. Place the triangular rule flat on the outfeed table. Turn the adjusting screws until the blade edge just contacts the triangular rule. After adjusting both adjusting screws, pull the lock pin to unlock the drum. Rotate the drum by turning the knob clockwise to make sure the blade pr[...]

  • Page 18

    Install the other blade as described above. Re-install the safety cover in its original position and be sure that the safety cover works properly and briskly. CAUTION : Do not tighten the blade installation bolts without the blade locating lug of the set plate correctly resting in the groove of the blade. This may cause damage to the blade and pote[...]

  • Page 19

    REMOVING OR INSTALLING THE JOINTER CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the jointer. The jointer can be easily removed from the auto-planer. You can carry it by yourself. 1. Removing the jointer Loosen the right and left knobs. Pull the jointer toward you as shown in the figure. The join[...]

  • Page 20

    Loosen the clamp screws which secure I the fence. Remove the fence. Align the line on the coupling with the pointer on the frame of the jointer. Coup1 ing s Line eoin t e r Align the two shafts of the jointer with the mating holes in the auto-planer. Push the jointer toward the auto-planer until the frame of the jointer contacts that of the auto- p[...]

  • Page 21

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes c Remove and check the carbon brushes re- 1 gularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes shoul[...]

  • Page 22

    ACCESSOR I ES ATTENTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade 0 Magnetic holder 0 Key Par[...]

  • Page 23

    Mar-22-’94 US 312 mm (12-9/32”) Model 2030s PLANER-JOINTER 23[...]

  • Page 24

    24[...]

  • Page 25

    Note: The switch and other part configurations may differ from country to country. 25[...]

  • Page 26

    MODEL 2030s MACHlNE 74 1 75 1 76 1 11 1 78 1 79 1 80 1 81 16 82 2 84 1 85 1 86 1 87 1 88 1 89 1 90 1 91 2 92 1 93 1 94 1 95 2 96 1 97 1 98 1 99 1 100 1 101 1 102 1 103 2 104 1 105 2 106 1 107 1 108 1 109 1 111 1 1 110 8 'v0M $& DESCRIPTION Mar.-22-'94 US $& DESCRIPTION MA( 1 2 3 4 5 6 1 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 2[...]

  • Page 27

    MODEL 20305 Mar-22-'94 US MACHINE 147 1 Hex Flange Head Bolt M6x17 148 1 Leg 149 1 Foot 150 1 Base Cover 151 1 Pan Head Screw M5x16 IWith Washer) 152 4 Spring Pin 6 36 153 1 Base 154 4 Cap 20 155 1 Drum cover 158 1 Retaining Ring S 12 157 1 SpringPin4-16 158 1 Spring Pin 4-32 159 1 Rod 12-95 160 1 Torsion Spring 14 161 2 Bedplate 162 1 Adlust [...]

  • Page 28

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Poiicy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh[...]