Multi-Tech Systems ISI5634PCI/4/8 manuel d'utilisation

ISI5634PCI/4/8 User Guide[...]

User Guide Model ISI5634PCI/4/8 P/N S0000109, Revision D This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2001 by Multi-Tech Systems, Inc. Multi- Tech Systems, Inc. makes no representation or warranties with respect to the contents[...]

Contents Chapter 1—Introduction and Description ........................... 5 Introduction ............................................................................................ 6 How to Use This Manual ........................................................................ 8 ISI5634PCI Applications ........................................[...]

Linux Driver for ISI5634PCI-4/8 ............................................................. 6 0 LINUX: Pre-Installation Issues ........................................ 6 0 LINUX: Copy driver fr om the media ............................... 6 1 LINUX: Driver installation and loading ......................... 6 2 LINUX: Set baud rate ...............[...]

Chapter 1—Introduction and Description[...]

6 ISI5634PCI/4/8 User Guide Introduction Welcome to the world of data communications. You have acquired one of the finest intelligent data and fax modems available today from one of Americas oldest and most respected modem manufacturersMulti- Tech Systems, Inc. The new Intelligent Serial Interface card, model ISI5634PCI is a multiport serial [...]

7 Chapter 1—Introduction and Description digital to analog only once before it reaches your modem. Upstream transmissions and transmissions between client modems are limited to data rates of 33.6 Kbps, as are downstream transmissions that are converted more than once on the telephone network. Note: Though these modems are capable of 56 Kbps downl[...]

8 ISI5634PCI/4/8 User Guide The processor, along with 256K bytes of RAM, works to allocate resources dynamically to the most active port. The ISI then generates one interrupt for an entire block of information and transfers the block to the systems microprocessor. The ISI5634PCI has eight Mini RJ-11 jacks. It is a 3/4 size add-on card that suppo[...]

9 Chapter 1 — Introduction and Description What Is in Your Modem Package? Your modem package has several components. Make sure you have them all before trying to operate your modem. Your package should include:  One ISI5634PCI/4 card  One ISI5634PCI/EC auxiliary module (or extender card; part of the ISI5634PCI/8 model only)  Four m[...]

10 ISI5634PCI/4/8 User Guide Technical Specifications Computer Requirements  Pentium ® - based PC or compatible with PCI Bus Architecture  One of these operating systems: Microsoft Windows 2000, NT v. 3.51 or v. 4.0; Windows 95, Windows 98 and Windows Me; Novell Netware versions 3.x and 4.x., SCO Open Server 5; Linux.  A CD-ROM drive. [...]

Chapter 2 — Hardware Installation[...]

12 ISI5634PCI/4/8 User Guide Introduction Included in this chapter are two sets of instructions for installing the Multi-Tech ISI5634PCI card in your PCI bus personal computer. The first set of instructions is for installing the ISI5634PCI card. The second set contain instructions for installing the ISI5634PCI card and the auxiliary module. Safety [...]

13 Chapter 2 — Hardware Installation 4 . To avoid damaging the ISI5634PCI card and your PC, make sure your computer and any peripheral equipment connected to it are turned off. The ISI5634PCI can be installed in any Pentium equivalent PCI bus computer. 5 . Remove the cover of your computer as instructed in your computers documentation. 6 . Loc[...]

14 ISI5634PCI/4/8 User Guide Installing the ISI5634PCI card WITH the auxiliary module: 1 . The auxiliary module attaches to the ISI5634PCI card. If you already have this card installed, you must remove it from the PC to install the auxiliary module. 2 . Before handling the ISI5634PCI card or the auxiliary module, discharge any static in your body b[...]

15 Chapter 2 — Hardware Installation 7 . Before installing the ISI5634PCI card, carefully line up the pin-out connectors of the ISI5634PCI card with the pin-out connectors of the auxiliary module. See figure below. Mounting screws Mounting posts Pin-out connectors 8 . Press gently but firmly to seat the module onto the card. 9 . Fasten the mounti[...]

16 ISI5634PCI/4/8 User Guide 1 1 . Fasten the retaining bracket to computer chassis and replace cover. 1 2 . Plug one end of the phone cable into each modems LINE jack and the other end into a phone line wall jack. 1 3 . Turn on the power to the computer. You now are ready to install the software/drivers. Note: The LINE jack is not interchangeab[...]

Chapter 3 — Software/Driver Installation[...]

18 ISI5634PCI/4/8 User Guide Introduction The ISI5634PCI card ships with drivers for each of the following operating systems: Windows ® 2000, Windows NT, Windows 95, Windows 98, Windows Me, Novell Netware versions 3.x and 4.x, SCO Open Server 5, and Linux. This chapter describes the installation of these drivers. In most cases, you will receive th[...]

19 Chapter 3 — Software/Driver Installation handling the ISI5634PCI board (the board should be kept in its shipping bag until used). During installation, handle the ISI5634PCI circuit card by its edges and keep one hand in contact with the PC chassis. 3 . Turn on the PC and start Windows 2000. 4 . Insert the ISI driver CD-ROM into the CD-ROM driv[...]

20 ISI5634PCI/4/8 User Guide 6 . The Install Hardware Device Drivers screen appears. Select "Search for a suitable driver ..." and click Next . 7 . The Locate Driver Files screen appears (Windows 2000 is seeking the driver for the ISI5634PCI card). Select CD-ROM drives and click Next .[...]

21 Chapter 3 — Software/Driver Installation 8 . The Driver File Search Results screen appears. Click Next . 9 . A progress screen will appear briefly while files are being copied.[...]

22 ISI5634PCI/4/8 User Guide 1 0 . A completion screen will appear. Click Finish . 11. Immediately after the ISI driver installation has been completed, another Found New Hardware screen will appear briefly indicating that the MultiTech ISI Port has been detected.[...]

23 Chapter 3 — Software/Driver Installation A second sequence of installation wizard screens appears. This sequence of screens deals with the setting up of ISI ports. The first screen in this sequence is the Found New Hardware Wizard -- Welcome screen. The Found New Hardware -- MultiTech ISI Port screen will appear once for each modem on th[...]

24 ISI5634PCI/4/8 User Guide 13. The Locate Driver Files screen appears (Windows 2000 is seeking the ISI Port device driver). Select CD-ROM drives and click Next . 14. The Driver Files Search Results screen will indicate that the isiport.inf file has been found on the CD-ROM. Click Next .[...]

25 Chapter 3 — Software/Driver Installation 1 5 . A completion screen will appear. It will indicate that the first MultiTech ISI Port has been set up successfully. Click Finish . Notice that the auto-detection facility of Windows 2000 will repeat the ISI Port installation sequence 3 more times for ISI5634PCI-4, or 7 more times for ISI[...]

26 ISI5634PCI/4/8 User Guide ISI5634PCI for Windows 2000: Installing Modems to COM Ports Pre-Requisite: Installation of Windows 2000 driver software must be completed before you can install the modems of the ISI5634PCI card. 1. Go to Start | Settings | Control Panel | Phone and Modem Options . 2. The Location Information screen appears. Enter the a[...]

27 Chapter 3 — Software/Driver Installation 4 . At the Install New Modem screen, click on "Don't detect my modem ... " and click Next . 5 . If the software driver CD-ROM (or other media, in cases of using drivers downloaded from the MultiTech web site) is not already in the appropriate disk drive in the PC, insert it now. 6. The Ad[...]

28 ISI5634PCI/4/8 User Guide 7. The Install from Disk screen will appear. Type or browse for the file path of the modem software (for example, E:servcarddriverswin2000). Click OK . 8. The Install New Modem screen will appear. Highlight ISI5634PCI -8 PCI 56K Modem. Click Next .[...]

29 Chapter 3 — Software/Driver Installation 9. The Install New Modem - port list screen will appear. Highlight the COM ports on which you want modems to be installed. You must allocate 4 ports for the ISI5634PCI-4, or 8 ports for the ISI5634PCI-8. Click Next . 10. A progress screen will appear as modem installation begins.[...]

30 ISI5634PCI/4/8 User Guide 11. Screens denoting the installation of modems to specific COM ports will appear for each modem installed. 1 2 . A completion screen will appear. Click Finish .[...]

31 Chapter 3 — Software/Driver Installation 13. The Phone and Modems Options screen ( Modems tab) will re- appear and display the modems that have just been assigned to COM ports. Installation of modems to COM ports in Windows 2000 is now complete. Remove ISI5634PCI Driver (Windows 2000) 1. Go to Start | Settings | Control Panel . 2. Click on Add[...]

32 ISI5634PCI/4/8 User Guide ISI5634PCI for Windows 2000: Installing ISI Manage- ment Software (server OSs only) If you are using a Windows 2000 Server operating system ("Server" or "Advanced Server"), you must decide whether you want to use the MultiTech ISI Management Software in conjunction with your ISI5634PCI board. The ISI[...]

33 Chapter 3 — Software/Driver Installation Installing the ISI5634PCI Card in Windows NT 3.51/4.0 The following procedure describes how to install the ISI5634PCI in a system operating Microsoft Windows NT 3.51 or 4.0 for use with Remote Access Service (RAS) server and other communications/fax server type applications. These procedures apply to bo[...]

34 ISI5634PCI/4/8 User Guide 5 . Click Start , Settings , Control Panel , and then double-click Network . In the Network dialog box, click the Adapters tab. Click Add . 6 . The Select Network Adapter dialog box appears. Click Have Disk .[...]

35 Chapter 3 — Software/Driver Installation 7 . The Insert Disk dialog box appears. Type in or browse for the path (file directory location) of the Windows NT driver (for example, E:servcarddriverswinntsetup.exe). C l ick OK . 8 . The Select OEM Option dialog box appears. Click OK . The driver files will be copied from the installation CD-ROM[...]

36 ISI5634PCI/4/8 User Guide 1 1 . The ISI Cards dialog box appears again showing the port resource allocation that has just been made. To add additional ISI5634PCI cards, click Add and repeat step 10. After the last ISI card has been added, click Close in the ISI Cards dialog box. 12. T h e Multi-Tech 8-port PCI Card appears in the Network Adapter[...]

37 Chapter 3 — Software/Driver Installation 1 3 . After bindings are reviewed and stored, the Network Settings Change dialog box appears. Click Yes to reboot your system. The ISI5634PCI now is installed in Windows NT and you are ready to install modems. Installing Modems to COM Ports in Windows NT 1 . Click Start | Settings | Control Panel , and [...]

38 ISI5634PCI/4/8 User Guide 4 . The Install New Modem - Models dialog box appears. Highlight ISI5634PCI-8 PCI 56K Modem and click Next . 5 . Select ports for modem use.  For the ISI5634PCI-4, you should have reserved four ports during driver installation. Highlight four ports in the list.  For the ISI5634PCI-8, you should have reserved[...]

39 Chapter 3 — Software/Driver Installation 6 . After the modems install to the ports, click Finish to return to the General tab. 7. To view COM port assignments (and make changes if necessary), use the Modem Properties dialog box.[...]

40 ISI5634PCI/4/8 User Guide 8. When finished, close the Modem Properties dialog box. The message below appears asking if you want to configure Dial-Up Networking. Click Yes . 9 . The Remote Access Setup dialog box appears. Click Add . 10. Each COM port appears in a separate Add RAS Device dialog box. To add the highlighted device, click OK .[...]

41 Chapter 3 — Software/Driver Installation 1 1 . The Remote Access Setup dialog box displays again. Repeat steps 9 and 10 until all modems are added. 1 2 . When all modems have been added, click Continue . 13. After bindings have been reviewed and stored, you will be prompted to re-start your computer. Click Yes . You have completed installation[...]

42 ISI5634PCI/4/8 User Guide Removing ISI5634PCI Driver in Windows NT 3.51/4.0 1 . Click Start , Settings , Control Panel , and then double-click Network . 2 . The Network dialog box appears. Click the Adapters tab. 3 . Select Multi-Tech 4, 8, 16-port ISI Card, and then click Remove . 4 . To complete an uninstall, reboot your computer. ISI5634PCI S[...]

43 Chapter 3 — Software/Driver Installation 6. (Follow either 6A or 6B, but not both.) A. From Windows Explorer, open the 95-98-Me directory on the CD-ROM (for example, E:SERVCARDDRIVERS95-98- MESETUP.EXE) or floppy drive that contains the ISI driver file. Highlight the file setup.exe . B. From the Start menu, go to Run . Browse to the path o[...]

44 ISI5634PCI/4/8 User Guide 9. Under Select Type of Card , do not check the Install ISA Card box. Click Next . 10. A completion screen appears. 11. When prompted to restart your computer, click Yes and click OK . 1 2 . During the re-start process, Windows 95/98/Me will detect the ISI5634PCI card. The Add New Hardware Wizard screen will appear. Cli[...]

45 Chapter 3 — Software/Driver Installation 13. The next screen asks, What do you want Windows to do? Click on Search for the best driver for your device. Click Next . 14. When asked for the location at which Windows 95/98/Me should search for the new driver, check Specify a Location and enter the path (file directory location) of the driver. 15.[...]

46 ISI5634PCI/4/8 User Guide 1 8 . To view the COM ports, click Control Panel and double-click System . The System Properties dialog box appears. The MultiTech PCI ISI Card is located under Multi Port Adapter . Click Ports (COM & LPT) to view the ports. Click OK to close.[...]

47 Chapter 3 — Software/Driver Installation Installing Modems to COM Ports in Win 95 /98/Me 1 . Click Start , Settings , Control Panel , and then double-click the Modems icon. I n the General tab, click Add . 2 . The Install New Modem dialog box will appear. Check the box marked "Don't detect my modem; I will select it from a list . &qu[...]

48 ISI5634PCI/4/8 User Guide 3 . The Install New Modem - Manufacturers dialog box appears. In the Manufacturers list, scroll down and highlight "MultiTech Systems." In the Models list, highlight the modem type used on the ISI board. Highlight "ISI5634PCI-8 PCI 56K Modem" and click Next . 4 . The Install New Modem dialog box appe[...]

49 Chapter 3 — Software/Driver Installation 5. When installing the first ISI modem, the Location Information screen will appear (it does not appear when additional modems or terminal adapters are installed). Fill in the appropriate area code and phone number information. 6 . After the modem installs to the port, click Finish.[...]

50 ISI5634PCI/4/8 User Guide 7 . Return to the General tab to view COM port assignments (and make changes if necessary). 8 . Click Add and repeat installation steps 27 to install modems (one at a time)  to the last three modem ports of the ISI5634PCI-4, OR  to the last seven modem ports of the ISI5634PCI-8.[...]

51 Chapter 3 — Software/Driver Installation Removing the ISI5634PCI Driver (Windows 95/98/Me) 1 . Click Settings , Control Panel , and then double-click Add/Remove Programs . 2 . From the list box, select MultiTech ISI Driver Device . 3 . Click Add/Remove and follow screen instructions. NetWare Driver Installation Multi-Tech Systems provides AIO [...]

52 ISI5634PCI/4/8 User Guide If you have downloaded the ISI driver from the MultiTech web site onto a diskette, use this command: COPY A:NOVELLAIOISIX.NLM F:SYSTEM To load the driver, go to the system or PC console (where the ISI card is installed) and enter the following at the prompt: LOAD AIOISIX [port= W ] [interrupt= X ] [name= Y ] [note= Z[...]

53 Chapter 3 — Software/Driver Installation This present installation section is task-oriented with minimal explanation of procedural steps. The section Multi-Tech Installation Script, which immediately follows this section, presents additional details to aid in installation. To install from CD-ROM: # mount -r /dev/cd0 /mnt # cd /mnt # cd servcar[...]

54 ISI5634PCI/4/8 User Guide 4. Copy the untarred (inflated or non-compressed) files to a floppy disk # cd /isi/unifiedinstimg301 #scosh - Select Manager . - Select Archive . - Select Create . - Press space bar to highlight tmp/ and usr/ directories. - Press <ENTER> to copy. - Make sure Device is pointed to the floppy disk. - Make sure that t[...]

55 Chapter 3 — Software/Driver Installation 5. Select as the Media Device Floppy Disk Drive. 6. Select Continue . 7. Highlight Multi-Tech ISA/PCI ... and select Install . 8. Enter Y (yes) to continue installing the ISI driver. 9. As many as four ISI cards can be installed in the server. Regardless of how many cards you will install in[...]

56 ISI5634PCI/4/8 User Guide 1. This text appears on the screen: You can install up to 4 ISA/PCI cards in a system. The PCI cards will be autodetected on bootup [ISI5634PCI is a PCI card, i.e., it has a PCI bus]. Enter the number of ISA cards you want to install and configure on your system (0-4): Select 0 if your computer has a PCI bus. This tells[...]

57 Chapter 3 — Software/Driver Installation ISICOM. The default prefix for the tty ports is ttyl. The default prefix for the printer is prnl. Is this acceptable? (y/n/ q). For most users, its best to select y , which entails accepting the default values. Then proceed to step 4. Details for use of non-default port/printer values . The /dev dire[...]

58 ISI5634PCI/4/8 User Guide printing). Specify a unique printer base name (printer parameters are outlined in the Multi_Setup Utility section in this manual ). Printer base name selected: _________________ When you have specified the device base name and the printer base name, press ENTER to continue. 4 . The confirmation screen lists the values y[...]

59 Chapter 3 — Software/Driver Installation Activating Ports in SCO Open Server 5 SCO Open Server 5 provides a device database that monitors the activity of serial ports through which users can log onto the host. If your ISI ports are used by terminals (e.g., to allow users to log onto your host), you must create an entry in the systems device[...]

60 ISI5634PCI/4/8 User Guide 5 . Repeat this command for each port you want to activate, using the lower case letter for local terminal use or upper case for modem control. Note: Only one of the options (e.g., modem control or local terminal access) should be enabled for any port at one time. For example, you cannot enable ttyl1a and then enable tt[...]

61 Chapter 3 — Software/Driver Installation issued from time to time. The 'make' utility, GNU C compiler, and the kernel sources need to be installed on your system. If any of these are missing, the compilation will fail. Most later Linux OSs install these elements automatically . LINUX: Copying the driver from the media The Linux drive[...]

62 ISI5634PCI/4/8 User Guide NOTE: To read from a DOS formatted floppy, a kernel with support for the FAT file system (either statically linked in the kernel or as modules) is required. Steps for copying the driver from a floppy: 1. Linux floppy disks are in ext2 format. 2. Insert Linux driver in drive A: and mount floppy drive. > mount -t ext2 [...]

63 Chapter 3 — Software/Driver Installation To view busy IRQs, enter: cat /proc/interrupts You must load the driver before you can load the firmware. You can load the driver manually using the 'insmod' utility. For ISI cards with the ISA bus, the I/O base address and the IRQ required by the card also need to be passed as parameters to i[...]

64 ISI5634PCI/4/8 User Guide first port on the first card). Save the configuration for a particular port using the 'save setup as' menu option as, for example, '1a' for the port / dev/ttyM1a. To connect to the port /dev/ttyM1a using minicom the next time, ' minicom 1a ' needs to be executed. LINUX: TTY Devices Created [...]

65 Chapter 3 — Software/Driver Installation - /dev/ttyM4a TO /dev/ttyM4h for the fo urth card Devices mapped for modem cards (ISI5634PCI-4 and ISI5634PCI-8 cards): For ISI5634PCI-4 cards (4 ports): - /dev/ttyM1a to /dev/ttyM1d for modem ports. For ISI5634PCI-8 cards (8 ports): - /dev/ttyM1a to /dev/ttyM1h for modem ports . LINUX -- Dial-in config[...]

66 ISI5634PCI/4/8 User Guide Note: A base I/O address of 0, e.g., ISIBaseX=oxo, or omission of these parameters for any card X, disables that particular card. Miscellaneous: Device files corresponding to ports on the ISI5634PCI cards are created in the /dev folder . Use ttyMxy for normal ports and cumxy for corresponding callout ports. The letter x[...]

67 Chapter 3 — Software/Driver Installation  rm ttyM1 *  rm ttyM2 *  rm ttyM3 *  rm ttyM4 * RedHat Linux 6.2/7.0 RPM Drivers for ISI5634PCI-4/8 Server Cards This installation procedure applies only to RedHat Linux versions 6.2 and 7.0. The standard ISI5634PCI Linux installation procedure (Linux Driver for Multi-Tech ISI[...]

68 ISI5634PCI/4/8 User Guide 3. List the RPM files on the CD-ROM using this command: ls LINUX-RPM: Copying the driver from a floppy The ISI driver .rpm file can be copied from a DOS formatted floppy using the 'mcopy' command if the 'mtools' have been installed. For RPM version 6.2, issue the command ' mcopy a:isicom-1.1-3.s[...]

69 Chapter 3 — Software/Driver Installation RPM, you will need to use the --force option in the RPM command as in step 5b below. 5a. For RPM version 6.2: Copy the RPM to a temporary folder. In this example, well use /isi. Installation is in three parts, building the isicom-smp.spec file from the source file, then building the actua[...]

70 ISI5634PCI/4/8 User Guide LINUX-RPM: Verifying the ports To test the installation, you can use the terminal program minicom. Use the command  minicom -s  to set up the tty port that you will use to communicate. 1. In the Configuration window, select Serial Port Setup. 2. Select A to set the Serial Device (for example, /dev/ttyM[...]

71 Chapter 3 — Software/Driver Installation For the ISI5634PCI-8, it uses the following: - /dev/ttyM1a TO /dev/ttyM1h for the first card - /dev/ttyM2a TO /dev/ttyM2h for the second card - /dev/ttyM3a TO /dev/ttyM3h for the third card - /dev/ttyM4a TO /dev/ttyM4h for the fourth card Devices mapped for modem cards (ISI5634PCI-4 and ISI5634PCI-8 car[...]

72 ISI5634PCI/4/8 User Guide HOWTO) explains in detail the procedure for configuring a Linux machine as a PPP server. This information is also available at http://www.interweft.com.au/other/ppp-howto/ppp-howto.html. The documentation in the PPP-HOWTO is directly applicable to ISI ports. Removing the ISI Driver (Linux-RPM) 1 . T o remove the ISI dri[...]

73 Chapter 3 — Software/Driver Installation  To load a custom configuration that was saved using the &W command, use ATZ . Note that the Z command must be in a command string by itself.  For a Macintosh, the initialization should include the &D0 command.  If you dont want the modem to always answer the phone, add S0=0 to the s[...]

74 ISI5634PCI/4/8 User Guide References ISI5634PCI User Guide The ISI5634PCI Quick Start Guide is a condensed version of this User Guide in printed form. It is especially intended for use during installation. The Quick Start Guide is also on the ISI CD-ROM. If you have any problems getting your modem to work, please consult this User Guide before c[...]

Chapter 4 AT Commands, S-Registers, & Result Codes[...]

76 ISI5634PCI/4/8 User Guide AT Commands AT commands are used to control the operation of your modem. They are so called because each command must be preceded by the characters AT to get the AT tention of the modem. AT commands can be issued only when the modem is in command mode or online command mode. The modem is in command mode whenever it is n[...]

77 Chapter 4 — AT Commands, S-Registers, Result Codes connecting to another modem. For a table of valid result codes, see Result Codes at the end of this chapter. You can issue several commands in one line, in what is called a command string . The command string begins with AT and ends when you press ENTER. Spaces to separate the commands are opt[...]

78 ISI5634PCI/4/8 User Guide Command: C n Carrier Control Values: n = 1 Default: 1 Description: C0 Transmit carrier always off. (Not supported.) C 1 Normal transmit carrier switching (included for back- ward compatibility with some software). Command: D s Dial Values: s = dial string (phone number and dial modifiers) Default: none Description: Dial[...]

79 Chapter 4 — AT Commands, S-Registers, Result Codes Command: DS= y Dial Stored Telephone Number Values: n = 03 Default: none Description: Dial a number previously stored in directory number y by the &Zy=x command. Example: ATDS=3 Command: E n Echo Command Mode Characters Values: n = 0 o r 1 Default: 1 Description: E 0 Do not echo keyboar[...]

80 ISI5634PCI/4/8 User Guide I 1 1 Display diagnostic information for the last modem con- nection, such as DSP and firmware version, link type, line speed, serial speed, type of error correction/data compression, number of past retrains, etc. Command: N n Modulation Handshake Values: n = 0 o r 1 Default: 1 Description: N 0 Modem performs handshake [...]

81 Chapter 4 — AT Commands, S-Registers, Result Codes Command: S r = n Set Register Value Values: r = S-register number; n varies Default: None Description: Set value of register S r to value of n , where n is entered in decimal format. E.g., S0=1 . Command: S r ? Read Register Value Values: r = S-register number Default: None Description: Read v[...]

82 ISI5634PCI/4/8 User Guide Command: X n Result Code Selection Values: n = 0  7 Default: 4 Description: X 0 Basic result codes ( e.g., CONNECT ); does not look for dial tone or busy signal. X 1 Extended result codes ( e.g., CONNECT 46000 V42bis ); does not look for dial tone or busy signal. X 2 Extended result codes with NO DIALTONE ; does not [...]

83 Chapter 4 — AT Commands, S-Registers, Result Codes Command: &C n Data Carrier Detect (DCD) Control Values: n = 0 or 1 Default: 1 Description: & C 0 Forces the DCD circuit to be always high. & C 1 DCD goes high when the remote modems carrier signal is detected, and goes low when the carrier signal is not detected. Command: &D[...]

84 ISI5634PCI/4/8 User Guide Command: &J n Auxiliary Relay Control Values: n = 0 Default: 0 Description: & J 0 The auxiliary relay is never closed. & J 1 Not supportedresponds ERROR . Command: &K n Flow Control Selection Values: n = 0, 3, or 4 Defaults: 3 Description: & K 0 Disable flow control. & K 3 Enable CTS/RTS hardw[...]

85 Chapter 4 — AT Commands, S-Registers, Result Codes Command: &T n V.54 Test Commands Values: n = 0 , 1 , 3 o r 6 Default: None Description: & T 0 Abort. Stop any test in progress. & T 1 Local analog loopback test. & T 3 Local digital loopback test. & T 6 Remote digital loopback test. Note: To stop a test, you must use the es[...]

86 ISI5634PCI/4/8 User Guide Command: &Zy =x Store Dialing Command Values: y = 03 (callback security disabled) or 029 (callback security enabled) x = Dialing command Default: None Description: Stores dialing command x in memory location y . Dial the stored number using the command ATDS=y . See also the #CBSn command. For callback security[...]

87 Chapter 4 — AT Commands, S-Registers, Result Codes Command: K n Break Control Values: n = 05 Default: 5 Description: Controls the response of the modem to a break received from the computer, the remote modem, or B command. Response is different for each of three different states. Data mode. The modem receives the break from the computer: [...]

88 ISI5634PCI/4/8 User Guide Command: N n Error Correction Mode Selection Values: n = 05, or 7 Default: 3 Description: N 0 Non-error correction mode with data buffering (buffer mode; same as &Q6 ). N 1 Direct mode. N 2 MNP reliable mode. If the modem cannot make an MNP connection, it disconnects. N 3 V.42/MNP auto-reliable mode. The[...]

89 Chapter 4 — AT Commands, S-Registers, Result Codes Description: V 0 Disable the appending of the protocol result code to the DCE speed. V 1 Enable the appending of the protocol result code to the DC E speed. V 2 Same as V1 . Command: X n XON/XOFF Pass-Through Values: n = 0 o r 1 Defaults: 0 Description: X 0 Modem responds to and disc[...]

90 ISI5634PCI/4/8 User Guide % D C 1 The modem ignores AT commands. Note: The modem responds to AT%DC for 10 seconds after power-up. Command: %E n Fallback and Fall Forward Control Values: n = 0, 1, or 2 Default: 2 Description: % E 0 Disable fallback and fall forward. % E 1 Enable fallback, disable fall forward. % E 2 Enable fallback and fall forwa[...]

91 Chapter 4 — AT Commands, S-Registers, Result Codes Command: #CBD n Callback Delay Values: n = 0255 Default: 1 5 Description: Sets the length of time (in seconds) that the mod em waits before calling back the remote modem. Command: #CBF? C allback Failed Attempts Display Values: n / a Description: Requests the number of failed callback passw[...]

92 ISI5634PCI/4/8 User Guide #CBP0 N o parity. #CBP1 Odd parity. #CBP2 Even parity. Command: #CBRy Callback Security Reset Values: y = 029 Default: None Description: Clears password &phone number in y memory location. Command: #CBS n Callback Enable/Disable Values: n = 0, 1, 2, or 3 Default: 0 Description: #CBS0 D isable callback security. #[...]

93 Chapter 4 — AT Commands, S-Registers, Result Codes to ten command character. Then press ENTER. Used mostly to issue hangup command: +++ATH<cr> . Command: %%%AT<cr>R e m ote Configuration Escape Sequence Values: n / a Description: Initiates remote configuration mode while online with remote modem. The remote configuration escape cha[...]

94 ISI5634PCI/4/8 User Guide About DTMF DTMF (dual tone multi frequency) is the signal to the phone company that you generate when you press an ordinary telephones touch keys. In the United States and perhaps elsewhere, its known as Touchtone phone (formerly a registered trademark of AT&T). DTMF has generally replaced loop disconnec[...]

95 Chapter 4 — AT Commands, S-Registers, Result Codes Dual Tone Multi-frequency (DTMF) was a technique proposed by the phone company to replace pulse dialing to make dialing faster and more reliable. In anticipation to adding other customer services, 6 additional digits were included, totaling 16 digits. Most commercial phones only in[...]

96 ISI5634PCI/4/8 User Guide S5 decimal 032 8 ( ^ H) Sets ASCII code for the backspace 33127 character. Values greater than 32 disable backspace. S6 seconds 265* 2* Sets time the modem waits after it goes off-hook before it begins to dial the telephone number. S7 seconds 1255* 50* S e t s ti m e t h e modem waits for a carrier signal be[...]

97 Chapter 4 — AT Commands, S-Registers, Result Codes which the modem attempts to connect. 0 = maximum modem speed 1 = reserved 2 = 1200/75 bps 3 = 300 bps 4 = reserved 5 = 1200 bps 6 = 2400 bps 7 = 4800 bps 8 = 7200 bps 9 = 9600 bps 10 = 12000 bps 11 = 14400 bps 12 = 16800 bps 13 = 19200 bps 14 = 21600 bps 15 = 24000 bps 16 = 26400 bps 17 = 2880[...]

98 ISI5634PCI/4/8 User Guide 12 = 52000 bps 13 = 54000 bps 14 = 56000 bps S42 decimal 0 1 1 Enables/disables the 56K auto rate. When 56K auto is disabled, fallback to V.34 is also disabled. 0 = disable; 1 = enable. S43 decimal 0 1 1 For testing and debugging only. Enables/disables V.32bis start-up auto mode operation. 0 = disable; 1 = enable.[...]

99 Chapter 4 — AT Commands, S-Registers, Result Codes Result Codes In command mode, ISI5634PCI modems can send responses called result codes to your computer. Result codes are used by communications programs and can also appear on your monitor. Terse Ve rbo se Description 0O K Command executed 1 CONNECT Modem connected to line 2R I N G Ring signa[...]

100 ISI5634PCI/4/8 User Guide 7 8 * CONNECT 48000 Connected at 48000 bps, 56K rate 7 9 * CONNECT 50000 Connected at 50000 bps, 56K rate 8 0 * CONNECT 52000 Connected at 52000 bps, 56K rate 8 1 * CONNECT 54000 Connected at 54000 bps, 56K rate 8 2 * CONNECT 56000 Connected at 56000 bps, 56K rate 8 8 DELAYED Delay is in effect for the dialed number 8 [...]

Chapter 5 W ar r anty , Ser vice, and T ech Suppor t[...]

102 ISI5634PCI/4/8 User Guide Software User License Agreement The ISI drivers and firmware are licensed by Multi-Tech Systems, Inc. to the original end-user purchaser of the product, hereafter referred to as Licensee . The License includes the distribution diskette, other accompanying programs, and the documentation. The ISI drivers and firmware, h[...]

103 Chapter 5 — Warranty, Service, and Tech Support Licensee agrees to implement sufficient security measures to protect Multi-Tech Systems, Inc. proprietary interests and not to allow the use, copying or transfer by any means, other than in accordance with this agreement. Licensee agrees that any breach of this agreement will be damaging to M[...]

104 ISI5634PCI/4/8 User Guide Limited Warranty Multi-Tech Systems, Inc. ( MTS ) warrants that its products will be free from defects in material or workmanship for a period of two years from the date of purchase, or if proof of purchase is not provided, two years from date of shipment. MTS MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, AND ALL IMPL[...]

105 Chapter 5 — Warranty, Service, and Tech Support Tech Support Multi-Tech has an excellent staff of technical support personnel available to help you get the most out of your Multi-Tech product. If you have any questions about the operation of this unit, call 1-800- 972-2439. Please fill out the information below and have it available when you [...]

106 ISI5634PCI/4/8 User Guide Service If your tech support specialist decides that service is required, your unit may be sent (freight prepaid) to our factory. Return shipping charges will be paid by Multi-Tech Systems. Include the following with this product:  A description of the problem.  Return billing and return shipping addresses.  C[...]

Appendices[...]

108 ISI4608 Owner's Manual Appendix ARegulatory Information FCC Regulations for Telephone Line Interconnection 1 . This equipment complies with part 68 of the Federal Communications Commission Rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number. This information must[...]

109 Appendix A - Base I/O Address Switch Settings operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service. 7 . If trouble is experienced with this equipment (the model of which is indicated below) please contact MultiTe[...]

110 ISI4608 Owner's Manual Class A Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This [...]

111 Appendix A - Base I/O Address Switch Settings Canadian Limitations Notice: Ringer Equivalence Number Notice: The ringer equivalence number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface, The termination on an interface may consist of any combinati[...]

112 ISI4608 Owner's Manual Fax Branding Statement The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains the following information:  Date and time the message is sent  Identification of th[...]

113 Appendix A - Base I/O Address Switch Settings New Zealand Telecom Warning Notice Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should NOT contact the Telecom Faults Service. [...]

114 ISI4608 Owner's Manual[...]

Index[...]

116 ISI5634PCI/4/8 User Guide Index Symbols 11-bit mode 90 56K operation digital loss when used with PBX 98 disabling the auto rate 98 maximum connect speed 97 A abort timer 96 activating ports in SCO 59 Answer command 77 Asynchronous Communications Mode command 84 Asynchronous W ord Length com- mand 90 A T commands 76113 #CBA 90 #CBD 91 #CBF? 9[...]

117 Index Q8 0 S= 81 S? 81 T8 1 V8 1 W8 1 X8 2 Y8 2 Z8 2 autoanswer 76, 9 5 Auxiliary Relay Control command 84 B backspace character, setting 96 base I/O address 10 baud rates 10 Bell 212A mode 77 blacklisting 89 Break Control command 87 break signal 87 bus types 10 C cables 10 Callback Attempts command 90 Callback Delay command 91 Callback Failed [...]

118 ISI5634PCI/4/8 User Guide Data Carrier Detect command 83 Data Compression Control com- mand 89 data mode 76, 80 Data Set Ready Control command 8 4 Data T erminal Ready command 8 3 DCD Control command 83 default settings 8 3 diagnostic information, displaying 80 Dial command 78 Dial Stored T elephone Number command 79 dial string modifiers 78 di[...]

119 Index installation activating ports in SCO Open Server 5 59 hardware 12 ISI5634PCI driver in Linux 60 in Netware 51 in SCO 52 in Windows 2000 18 in Windows 95/98/Me 42 in Windows NT 33 modems to COM ports in Netware 52 in SCO 59 in Windows 2000 26 in Windows NT 37 Linux 65 Linux-RPM 71 software/drivers in Linux 62 in Netware 51 in SCO Open Serv[...]

120 ISI5634PCI/4/8 User Guide modem install Linux 64 Linux RPM 70 Netware 52 SCO 59 Windows 2000 26 Windows 95/98/Me 47 Windows NT 37 Modem Port Flow Control com- mand 86 Modem Reset command 82 modems activating ports SCO 59 installing to COM ports Linux 65 Linux-RPM 71 Netware 52 SCO 59 Windows 2000 27 Windows 95/98/Me 47 Windows NT 37 Modulation [...]

121 Index Result Codes Enable/Disable com- mand 80 retrain 82 Return Online to Data Mode com- mand 80 rings, setting number of 95 ROM checksum 79 S S-registers 95113 reading 81 S0 95 S1 95 S10 96 S108 98 S11 96 S2 95 S28 96 S3 95 S30 96 S35 96 S36 96 S37 96 S38 97 S4 95 S42 98 S43 98 S48 98 S5 96 S6 96 S7 96 S8 96 S89 98 S9 96 setting 81 safety [...]

122 ISI5634PCI/4/8 User Guide T tech support 105 technical specifications 10 temperature 10 testing the modem 85 T one Dialing command 81 tones, dialing 96 Transmit Break command 86 U uninstall ISI driver Linux 66 Linux RPM 72 Netware 52 SCO 60 Windows 2000 31 Windows 95/98/Me 51 Windows NT 42 V V .22 mode 77 V .22bis Guard T one Control com- mand [...]