Français dropdown-ico

Pelco DX8000 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Pelco DX8000. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Pelco DX8000 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Pelco DX8000 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Pelco DX8000 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Pelco DX8000
- nom du fabricant et année de fabrication Pelco DX8000
- instructions d'utilisation, de réglage et d’entretien de l'équipement Pelco DX8000
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Pelco DX8000 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Pelco DX8000 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Pelco en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Pelco DX8000, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Pelco DX8000, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Pelco DX8000. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    DX8000 Hard Drive Upgrade Installation to a Four-Drive System C1609M (6/04) Digital Video Recorder DX8000[...]

  • Page 2

    Protecting people and property in a million locations worldwide.[...]

  • Page 3

    C1609M (6/04) 1 Introduction The following instructions serve as a guide for upgrading the storage capacity of the DX8000 Series digital video recorder (DVR). Included are step-by-step directions for installing one to three additional hard disk drives in the DX8000 using the DX8000-UP250 hard disk upgrade kit. The following illustrates how to upgra[...]

  • Page 4

    2 C1609M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and T ools Needed sections. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shutti[...]

  • Page 5

    C1609M (6/04) 3 Figure 2. Removing Power Cord from Unit[...]

  • Page 6

    4 C1609M (6/04) Figure 3. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective m[...]

  • Page 7

    C1609M (6/04) 5 Prepare Unit for Drive Installation IMPORT ANT : If this upgrade requires the replacement of the DX8000’ s primary hard disk drive (drive 1 nearest the CD/DVD drive), refer to the instructions for replacing the primary drive (manual number C1606M). This manual should be included with this upgrade kit if a primary drive replacement[...]

  • Page 8

    6 C1609M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section. a. Remove the two top-most screws on the left and right side panels of the DX8000. Ref[...]

  • Page 9

    C1609M (6/04) 7 COMPONENT LA YOUT Figure 5 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity . POWER SUPPLY DIMM SOCKETS (RAM) CPU VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE FRONT CROSS-BRACE MOTHERBOARD IDE CONNECT[...]

  • Page 10

    8 C1609M (6/04) Move the Front and Rear Cross-Braces 1. Unscrew and lift out both the front and rear cross-braces. Moving these parts out of the way will make it easier for you to access the hard drive mounting baskets and PCI Slot 6. a. Use a Phillips-head screwdriver to remove the two flat-head screws that secure each cross-brace. Refer to Figure[...]

  • Page 11

    C1609M (6/04) 9 b. Carefully place each cross-brace across the rear section of the unit. Refer to Figure 6. WARNING: Do not disconnect the wires or remove the front cross-brace entirely from the unit— doing so may cause damage to the fan’ s power connection. Figure 7. Placing Front and Rear Cross-Braces Out of the Way[...]

  • Page 12

    10 C1609M (6/04) Disconnect the Data and Power Cables When removing data and power cables, pull the connectors straight out. Do not rock connectors back and forth or remove a connector by pulling it by its wires. 1. Remove the IDE data cables from the hard drives, CD-RW drive, and motherboard: a. Carefully pull the plastic tab of each cable connect[...]

  • Page 13

    C1609M (6/04) 11 2. Remove the power connectors from the hard drives. 2 Figure 9. Removing Hard Drive Power Connections[...]

  • Page 14

    12 C1609M (6/04) REMOVE THE DRIVE MOUNT BASKETS 1. Remove hard drive mounting basket(s): a. Using a Phillips-head screwdriver , unfasten the four screws that attach each drive basket to the chassis. Refer to Figure 10. b. Gently lift the basket up and out with drive(s) attached. Be careful not to force the basket free or to disturb other components[...]

  • Page 15

    C1609M (6/04) 13 Install Additional Drive(s) NOTE: This upgrade kit includes up to four Pelco-certified hard disk drives. Using any other hard disk drives with the DX8000 voids the manufacturer’ s warranty for this product. PREP ARE THE DRIVES Plan where the drives will go before you install them: a. Drives should be installed in order from right[...]

  • Page 16

    14 C1609M (6/04) MOUNT THE ADDITIONAL DRIVES 1. Mount the hard disk drives in the drive baskets. Refer to Figure 12 below . a. Make sure drives are mounted in the baskets so that access to connectors is not blocked. b. Attach each drive to the basket using the two screws that came with the upgrade kit. c. T ighten the screws securely but do not ove[...]

  • Page 17

    C1609M (6/04) 15 2. Mount the drive baskets back into the chassis: a. Align the baskets and press down firmly to ensure that they fit flush against the top of the chassis bracket. Refer to Figure 13. b. Secure the drive baskets to the chassis using four screws each. Figure 13. Replacing Drive Baskets[...]

  • Page 18

    16 C1609M (6/04) DATA CONNECTOR MASTER/SLAVE JUMPER POWER CONNECTOR PIN 1 SET THE MASTER / SLA VE JUMPERS Each hard drive must be configured as either a master or slave device to operate correctly . A jumper is used to configure a pair of connected hard drives to operate in a master/slave relationship. A jumper is a small plastic part that slides o[...]

  • Page 19

    C1609M (6/04) 17 Figure 15. Setting Drive Jumpers MASTER 1 SLAVE 2 MASTER 3 SLAVE 4 CD-RW FRONT OF DVR JUMPER SLAVE SETTING MASTER SETTING[...]

  • Page 20

    18 C1609M (6/04) INST ALL THE DX8000-EXD IDE EXTENDER CARD 1. Locate PCI slot 6 on the system motherboard. This is the expansion slot that is farthest from the unit’ s power supply . Refer to Figure 16. Figure 16. Location of PCI Slot 6[...]

  • Page 21

    C1609M (6/04) 19 2c 2a 2. Remove the slot cover from PCI slot 6: a. Using a Phillips-head screwdriver , remove the screw that fastens the slot cover to the chassis. b. Retain this screw for use in step 5. c. Remove the slot cover from PCI slot 6. Figure 17. PCI Slot 6 Slot Cover 3. Carefully remove the DX8000-EXD adapter card from its static-safe p[...]

  • Page 22

    20 C1609M (6/04) 5. Install the DX8000-EXD extender card in PCI slot 6: a. Carefully move aside any cables blocking access to PCI slot 6. b. Insert the DX8000-EXD extender card in PCI slot 6. Refer to Figure 18. c. Press down firmly to ensure that the card is fully seated into the PCI slot. NOTE: Avoid using excessive force when inserting the card [...]

  • Page 23

    C1609M (6/04) 21 5d d. Using the screw you removed in step 2, secure the extender card to the chassis. Refer to Figure 19. Figure 19. Securing the DX8000-EXD IDE Extender Card[...]

  • Page 24

    22 C1609M (6/04) RECONNECT DA T A AND POWER CABLES IMPORT ANT : Data and power connectors fit together only one way . All connectors are keyed to ensure that they are inserted in the proper orientation. Examine the drive, motherboard and cable connectors before installation so that connectors are properly aligned. Make sure connectors are seated in[...]

  • Page 25

    C1609M (6/04) 23 Figure 20. Installing the CD-RW Data Cable to the Extender Card 1b 1 a IDE1[...]

  • Page 26

    24 C1609M (6/04) 2. Using one of the straight data cables that came with your upgrade kit, connect Hard Drive 1 and Hard Drive 2 to the primary IDE connector on the system motherboard: a. Connect the straight data cable to Hard Drive 1 and Hard Drive 2 according to the example shown in Figure 21. b. Connect the straight data cable to the primary (b[...]

  • Page 27

    C1609M (6/04) 25 4. Connect the hard drive power connectors according to the diagram in Figure 22. 4 4 Figure 22. Installing Hard Drive Power Connectors[...]

  • Page 28

    26 C1609M (6/04) Reassemble the Unit 1. Replace the front and rear cross-braces, and secure them with the flat-head screws you set aside earlier . Refer to Figure 23. Figure 23. Replacing Front Cross-Brace[...]

  • Page 29

    C1609M (6/04) 27 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 24. Figure 24. Replacing Chassis Cover[...]

  • Page 30

    28 C1609M (6/04) 3. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 4. Plug the power cord back into the power supply and then into the wall. 5. T urn on the power switch and allow the unit to start up and find the new hard disks. This may take up to five minutes. ON[...]

  • Page 31

    C1609M (6/04) 29 Initialize the New Drives to Store Data 1. While the DX8000 starts, the built-in setup program will automatically detect the newly installed drives and reconfigure the basic settings of the unit to make use of the increased storage capacity . No action by the user is necessary during this step. 2. After the unit has detected and pr[...]

  • Page 32

    30 C1609M (6/04) b. For each drive listed, click the Not Used button. Refer to Figure 27. A drop-down menu appears. There may be more than one drive listed, as shown in the figure below . Figure 27. Opening Drive Options Menu c. For each drive listed, select the Allocation option from the drop-down menu. Figure 28. Selecting Allocation Option for E[...]

  • Page 33

    C1609M (6/04) 31 d. Click Begin Allocation. Figure 29. Initializing Drive Allocation e. The following warning appears. Click Y es. Figure 30. Format Warning Dialog Box[...]

  • Page 34

    32 C1609M (6/04) f. Wait while the DX8000 prepares the newly installed drives for video storage. Y ou will see the following progress bar while the formatting is underway . Figure 31. PDB Database Creation Progress Bar 4. After the storage allocation procedure is complete, the DX8000 will reboot automatically and the unit will be ready to resume se[...]

  • Page 35

    PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models[...]

  • Page 36

    Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. Windows is a registered trademark of Microsoft Corporation. C1609M (6/04) W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/[...]