Toshiba A10 Series manuel d'utilisation

T OSHIBA Satellite A10 Series Port able Personal Computer User ’ s Manual[...]

Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein. TOSHIBA Satellite A10 Series Portable Personal Computer User’s Manual [...]

FCC information Product Name : Satellite A10 Model number : PSA10 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference [...]

FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 . This device may not cause harmful interference. 2 . This device must accept any interference received, including interference that may cause undesired operation. Cont act Address: TOSHIBA America Information Systems, Inc. 974[...]

Modem warning notice Conformity St atement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an uncon[...]

Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give yo[...]

Jap an regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, t[...]

Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, opera- tional and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does n[...]

3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Canada: 1353A-L4AINT Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. [...]

Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only[...]

ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) ❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a ) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been succe[...]

General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The T[...]

TEAC CD-ROM drive CD-224E, CD- RW/DVD-ROM drive DW-224E safety instruction CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, [...]

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PROD- UCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to th[...]

VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUN[...]

3. To prevent direct exposure to the laser beam, do not try to open the enclosure. CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contac[...]

vermeiden darf das Gerät nicht geöffnet werden. ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling. APPARATET BOR KUN [...]

HIT ACHI DVD-ROM drive GDR-8082 safety instruction CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the perf[...]

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the [...]

VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUN[...]

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the [...]

ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling. APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARA[...]

xxiii T able of Content s Preface Manual contents ............................................................................. xxxi Conventions ................................................................................... xxxii Abbreviations .................................................................................... xxxii Icons ....[...]

xxiv Communications ................................................................................. 1 - 7 Security .............................................................................................. 1 - 7 S o f t w a r e ............................................................................................. 1 - 7 Special features[...]

xxv Restoring the preinstalled software from the Product Recovery CD-ROM ....................................................... 3-12 Chapter 4 Operating Basics Pointing devices ................................................................................ 4 - 1 Using the Touch Pad .................................................................[...]

xxvi Chapter 5 The Keyboard Typewriter keys ................................................................................. 5 - 1 F1 … F12 function keys ..................................................................... 5 - 2 Soft keys: Fn key combinati ons ........................................................ 5 - 2 Emulating keys on enha[...]

xxvii Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7 - 1 Accessing HW Setup ......................................................................... 7 - 1 HW Setup window .............................................................................. 7 - 1 Supe[...]

xxviii CD-RW/DVD-ROM drive ................................................................... 9-14 DVD-R/-RW drive .............................................................................. 9-16 Diskette drive .................................................................................... 9-18 PC card .....................................[...]

xxix Appendix I Parts Numbers .................................................................................... I-1 Glossary Index[...]

xxx[...]

xxxi Preface Congratulations on your purchase of the Satellite A10 series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A10 series computer. It[...]

xxxii Chapter 4, Operating Basics , includes instructions on using the following devices: Touch Pad, USB diskette drive, optical media drives, modem, wireless communica- tion features, LAN. It also provides tips on care of the computer, diskettes and CD/ DVDs. Chapter 5, The Keyboard , describes special keyboard functions including the keypad overl[...]

xxxiii Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbo[...]

xxxiv[...]

xxxv General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text o[...]

xxxvi Central Processing Unit ("CPU") Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions: 1. use of certain external peripheral products 2. use of battery power instead of AC power 3. use of certain multimedia games or videos with special effects 4. use of standard t[...]

I NTRODUCTION Chapter 1 Introduction Equipment checklist .......................................................................... 1 - 1 Hardware ............................................................................................ 1 - 1 S o f t w a r e ........................................................................................[...]

I NTRODUCTION[...]

1-1 I NTRODUCTION Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not prein- stalled by TOSHIBA. Equipment checklist Carefully unpack your[...]

1-2 User's Manual I NTRODUCTION • Online manual ❑ Product Recovery CD-ROM Document ation • Satellite A10 Series Portable Personal Computer User's Manual • Microsoft Windows XP manual package • Instruction Manual for Safety & Comfort • End User License Agreement Features The computer uses TOSHIBA’s advanced Large Scale In[...]

1-3 I NTRODUCTION Memory Slots 128, 256 or 512 MB memory modules can be installed in the two memory slots for a maximum of 1 GB system memory. Video RAM Allocated a part of System Memory dynamically. (Limit of graphics memory is 32MB at 128MB of System Memory, Limit of Graphics memory is 64MB at more than 256MB of System Memory) Power Battery pack [...]

1-4 User's Manual I NTRODUCTION • CD-ROM Mode 1, Mode 2 • CD-ROM XA Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 DVD-ROM drive Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12cm(4.72") DVDs wit[...]

1-5 I NTRODUCTION DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at u[...]

1-6 User's Manual I NTRODUCTION Pointing device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer. Ports Parallel Some models are equipped with a parallel port for parallel printer or other parallel device (ECP compatible).Note that some models are not equipped with this port. External [...]

1-7 I NTRODUCTION Special features Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in[...]

1-8 User's Manual I NTRODUCTION Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Display automatic This feature automatically cuts off power to the internal power off display when there is no input from the keyboard or pointing device for a time[...]

1-9 I NTRODUCTION Battery save mode This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver. Panel power off/on This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. You [...]

1-10 User's Manual I NTRODUCTION HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To start the utility, click the Windows Start button and click Control Panel. In the Control Panel, select the TOSHIBA HW Setup icon. TOSHIBA Console TOSHIBA Console is a[...]

1-11 I NTRODUCTION Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory expansion A 128, 256 or 512 MB memory module (PC2100, DDR) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. [...]

1-12 User's Manual I NTRODUCTION[...]

T HE G RAND T OUR Chapter 2 The Grand T our Front with the display closed ........................................................... 2 - 1 Left side .............................................................................................. 2 - 2 Right side ........................................................................................[...]

T HE G RAND T OUR[...]

T HE G RAND T OUR 2-1 Chapter 2 The Grand T our This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. Figure 2-1 Front of the computer with display close[...]

User's Manual T HE G RAND T OUR 2-2 Wireless Slide this switch toward the left of the computer to turn communication off Wireless LAN function. Slide it toward the right of switch the computer to turn on the functions (Wireless LAN model or Wireless LAN ready model only). CAUTION: Set the switch to off in airplanes and hospitals. Check the wir[...]

T HE G RAND T OUR 2-3 Right side Headphone jack This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automati- cally disabled. PC card slot A PC card slot can accommodate one 5 mm Type II card. You can install any industry standard PC card such [...]

User's Manual T HE G RAND T OUR 2-4 DVD-R/-RW drive Some models are equipped with a full-size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run CD/DVDs without using an adaptor.You can also write CD/DVDs. Modem jack In areas where an internal modem is installed as standard equipment, there is a modem jack t[...]

T HE G RAND T OUR 2-5 Link indicator This indicator glows green when the computer is connect- (green) ed to a LAN and the LAN is functioning properly. Parallel port Some models are equipped with a Centronics-compatible, 25-pin parallel port that is used to connect a parallel printer or other parallel device.This port supports Extended Capabilities [...]

User's Manual T HE G RAND T OUR 2-6 Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Figure 2-5 The underside of the computer Battery release Slide this latch to release the battery pack for removal. latch For detailed information on removing the battery packs,refer to[...]

T HE G RAND T OUR 2-7 Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle. Figure 2-6 The front with the display open Display hinge The displ[...]

User's Manual T HE G RAND T OUR 2-8 Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Power button Press the power button to turn the computer’s power on and off. Touch Pad A Touch Pad located slightly in the left from the center of the palm res[...]

T HE G RAND T OUR 2-9 keyboard indicators CD-ROM This indicator glows green when the computer is drive accessing a diskette in the diskette drive or a disk in the CD-ROM,DVD-ROM, DVD-R/-RW or CD-RW/DVD-ROM drive. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key in[...]

User's Manual T HE G RAND T OUR 2-10 Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard . Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights [...]

T HE G RAND T OUR 2-11 NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 o while it is operating. 2. Do not set anything on top of the diskette drive. Fixed optical media drive CD-ROM drive Some models are equipped with a full-size,CD-ROM drive. ROM d[...]

User's Manual T HE G RAND T OUR 2-12 DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly. Code Region 1. Canada, United States 2. Japan, Europe, South Africa, Middle East 3. Southeast Asia, East Asia[...]

T HE G RAND T OUR 2-13 Code Region 1. Canada, United States 2. Japan, Europe, South Africa, Middle East 3. Southeast Asia, East Asia 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6. China DVD-R/-RW drive Some models are equipped with a full- size D[...]

User's Manual T HE G RAND T OUR 2-14 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6. China Universal AC adaptor The universal AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adju[...]

G ETTING S TARTED Chapter 3 Getting S t arted Setting up your work space .............................................................. 3 - 1 General conditions .............................................................................. 3 - 2 Placement of the computer ................................................................. 3 - 2 Seatin[...]

G ETTING S TARTED[...]

3-1 G ETTING S TARTED Chapter 3 Getting S t arted This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort . This guide, which is included with the computer, expl[...]

User's Manual G ETTING S TARTED 3-2 General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑ Make sure the AC power cord connects to an outlet that is close t[...]

3-3 G ETTING S TARTED Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. Figure 3-1 Posture and positioning of the computer ❑ Place your chair so that the keyboard is at or slight[...]

User's Manual G ETTING S TARTED 3-4 Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ❑ Avoid placing the computer in front of bright ligh[...]

3-5 G ETTING S TARTED Connecting the universal AC adaptor Attach the universal AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The universal AC adaptor can be connected to any po[...]

User's Manual G ETTING S TARTED 3-6 Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1 . Slide the display latch on the front of the computer to the right. 2 . Lift the panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display p[...]

3-7 G ETTING S TARTED 2 . Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power S t arting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can cl[...]

User's Manual G ETTING S TARTED 3-8 3 . Click start then click Turn Off Computer . From the Turn Off Computer menu select Turn Off . 4 . Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature sa[...]

3-9 G ETTING S TARTED Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4 . See Chapter 5, Keyboard , for details. To enter Hibernation mode, follow the steps below. 1 . Click start . 2 . Select Turn Off Computer . 3 . Open the Turn Off Computer dialog box. Hibernate is not displayed. 4 . Press the Shift key. The Standby [...]

User's Manual G ETTING S TARTED 3-10 CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. St andby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the pow[...]

3-11 G ETTING S TARTED ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature. ❑ You can use the panel power off feature. Executing standby NOTE: You can also enable Standby by pressing Fn + F3 . See Chapter 5, Keyboard , for details. You can enter stan[...]

User's Manual G ETTING S TARTED 3-12 Rest arting the computer Certain conditions require that you reset the system. For example, if: ❑ You change certain computer settings. ❑ An error occurs and the computer does not respond to your keyboard commands. There are three ways to reset the computer system: 1 . Click start then click Turn Off Co[...]

O PERATING B ASICS Chapter 4 Operating Basics Pointing devices ................................................................................ 4 - 1 Using the Touch Pad .......................................................................... 4 - 1 Using the USB diskette drive ............................................................ 4 - 2 Con[...]

O PERATING B ASICS Moving the computer ...................................................................... 4-23 Heat dispersal .................................................................................. 4-24[...]

O PERATING B ASICS 4-1 Chapter 4 Operating Basics This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication, and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Pointing devices The compu[...]

User's Manual O PERATING B ASICS 4-2 Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44- megabyte or 720-kilobyte d[...]

O PERATING B ASICS 4-3 Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1 . Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing [...]

User's Manual O PERATING B ASICS 4-4 Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1 . a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. Figure 4-3 Pressing the DVD-ROM eject button b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power [...]

O PERATING B ASICS 4-5 2 . Pinch the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3 . Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DV[...]

User's Manual O PERATING B ASICS 4-6 CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Be careful to keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4 . Press gently at the center of the CD/DVD until you feel it click into pla[...]

O PERATING B ASICS 4-7 Writing CDs on CD-RW/DVD-ROM drive CAUTIONS: 1. When the drawer pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the drawer fully open. 2. Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the drawer, the CD/DVD could fly off the spindle and [...]

User's Manual O PERATING B ASICS 4-8 Before writing or rewriting Please observe the following points when you write or rewrite the data. ❑ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. C D - R : TAIYO YUDEN CO., LTD. Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORA[...]

O PERATING B ASICS 4-9 ❑ Do not perform any of the following actions: • Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. • Start a communication application such as a modem. • Apply impact or vibration to the PC. • Install, remove or connect external devices, including the [...]

User's Manual O PERATING B ASICS 4-10 ❑ Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents. ❑ Damage that may be caused by using third[...]

Read/write function chart Disc type C D - R CD -R W DVD-R DVD-RW DVD-RAM DVD+R DVD+RW Read Write Drag’n Drop CD*1 No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No *1 Software supplied with the product can be used for writing to a disc. Writing CD/DVDs on DVD-R/-RW drive O PERATING B ASICS 4-11[...]

User's Manual O PERATING B ASICS 4-12 ❑ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-RW disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. C D - R : TAIYO YUDEN CO., [...]

O PERATING B ASICS 4-13 Writing CD/DVDs on DVD-R/-RW drive ❑ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data. Before writing or rewriting Please observe the following points when [...]

User's Manual O PERATING B ASICS 4-14 ❑ Make sure writing or rewriting is completed before going into standby/ hibernation. ❑ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand. ❑ Keep mobile phones and other wireless communication d[...]

O PERATING B ASICS 4-15 Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1 . Store your CD/DVDs in the container they came in to protect them and keep them [...]

User's Manual O PERATING B ASICS 4-16 6 . Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields. Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. NOTE: The internal modem does not sup[...]

O PERATING B ASICS 4-17 3 . Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4 . Select a region from the region menu or a telephony location from t[...]

User's Manual O PERATING B ASICS 4-18 Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the[...]

O PERATING B ASICS 4-19 Figure 4-11 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1. Modem speed is slow or commu[...]

User's Manual O PERATING B ASICS 4-20 ❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s. (Revision A, Revision A/B combo type) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1Mbit/s. (Revision B) ❑ Automatic Transmit Rate Select mechanism in the t[...]

O PERATING B ASICS 4-21 Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communi- cation functions. Indicator status Indication Ind ica to r off Wireless communication switch is set to off. Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an applica- tion. If[...]

User's Manual O PERATING B ASICS 4-22 Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 me[...]

O PERATING B ASICS 4-23 CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1 . Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2 . Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting fr[...]

User's Manual O PERATING B ASICS 4-24 ❑ Close all port covers. ❑ Use the carrying case when transporting the computer. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Yo[...]

T HE K EYBOARD Chapter 5 The Keyboard Typewriter keys ................................................................................. 5 - 1 F1 … F12 function keys ..................................................................... 5 - 2 Soft keys: Fn key combinati ons ........................................................ 5 - 2 Emulating ke[...]

T HE K EYBOARD[...]

5-1 T HE K EYBOARD Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s key- board layout your computer is conf[...]

User's Manual 5-2 T HE K EYBOARD F1 … F12 function keys The function keys, not to be confused with Fn , are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked [...]

5-3 T HE K EYBOARD Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard is smaller and has [...]

User's Manual 5-4 T HE K EYBOARD Hot keys Hot keys ( Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press Fn + F1 t[...]

5-5 T HE K EYBOARD Standby: When you press Fn + F3 , the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4 , the computer enters Hibernation. To avoid entering Hibernation unexpectedly, a [...]

User's Manual 5-6 T HE K EYBOARD LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver. NOTE:[...]

5-7 T HE K EYBOARD Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “ F number ” key. To start the TOSHIBA Accessibility Utility, click start , point to All Programs , point to TOSHIBA Utilities and click Accessibility . Windows special keys The [...]

User's Manual 5-8 T HE K EYBOARD Numeric mode To turn on the Numeric mode, press Fn + F11 . The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay T emporarily using normal keyboard (overlay on) While using the overlay, [...]

5-9 T HE K EYBOARD T emporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn . 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric en[...]

User's Manual 5-10 T HE K EYBOARD[...]

P OWER AND P OWER -U P M ODES Chapter 6 Power and Power-Up Modes Power conditions ............................................................................... 6 - 1 Power indicators ............................................................................... 6 - 2 Battery indi cators ...........................................................[...]

P OWER AND P OWER -U P M ODES[...]

P OWER AND P OWER -U P M ODES 6-1 Chapter 6 Power and Power-Up Modes The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions T[...]

6-2 User's Manual P OWER AND P OWER -U P M ODES Table 6-1 Power conditions continued Power on Power off (no operation) A C Battery • Operates adaptor charge is • LED: Battery off no t above low DC IN off connected battery trigger point Battery • O perates charge is • L E D : Battery below low flashes orange battery DC IN off trigger po[...]

P OWER AND P OWER -U P M ODES 6-3 No light Under any other conditions, the indicator does not light. NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is o[...]

6-4 User's Manual P OWER AND P OWER -U P M ODES Battery p ack When the universal AC adaptor is not connected, the computer’s main power source is a removable lithium-ion battery, also referred to in this manual as the battery pack. You can purchase additional battery packs for extended use of the computer away from an AC power source. Before[...]

P OWER AND P OWER -U P M ODES 6-5 **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key to set Date/Time. CAUTION: The computer’s RTC battery is a nickel metal hydride battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or[...]

6-6 User's Manual P OWER AND P OWER -U P M ODES 3 . Never short-circuit the battery pack by contacting the terminals with a metal object. A short-circuit can cause fire or otherwise damage the battery pack and possibly cause injury. To avoid accidental short-circuit, always wrap the battery pack in plastic and cover the terminals with electric[...]

P OWER AND P OWER -U P M ODES 6-7 Care and use of the battery pack 3 . Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture. 4 . Keep the battery pack out or reach of infants and children. It can cause injury[...]

6-8 User's Manual P OWER AND P OWER -U P M ODES 2 . To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power for an extended[...]

P OWER AND P OWER -U P M ODES 6-9 Charging time (hours) Battery type Power on Power off Battery pack 3600mAh 3 . 5 t o 9 o r l onger about 2.6 4400mAh 4 t o 1 1 o r longer about 2.6 RTC battery 8 Doesn’t charge NOTE: The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the c[...]

6-10 User's Manual P OWER AND P OWER -U P M ODES Monitoring battery cap acity Remaining battery power can be monitored in the Power Save Modes window in Power Saver. NOTES: 1. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The com- puter needs this time to check the battery’s rem[...]

P OWER AND P OWER -U P M ODES 6-11 Care and use of the battery pack ❑ How much charge the battery contained to begin with. ❑ How you use optional devices, such as a PC card, to which the battery supplies power. ❑ Enabling Standby mode conserves battery power if you are frequently turning the computer off and on. ❑ Where you store your progr[...]

6-12 User's Manual P OWER AND P OWER -U P M ODES 4 . Connect the universal AC adaptor to the computer and the power cord to a power outlet. The DC IN indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged. If the DC IN indicator does not glow, power is not being supplied. Ch[...]

P OWER AND P OWER -U P M ODES 6-13 3. In Hibernation mode, data will be lost if you remove the battery and disconnect the universal AC adaptor before the save is completed. Wait for the Built-in HDD indicator to go out. 4. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of th[...]

6-14 User's Manual P OWER AND P OWER -U P M ODES CAUTIONS: 1. The battery pack is a lithium-ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recom- mended by TOSHIBA as replacements. 2. Do not touch the latch while ho[...]

P OWER AND P OWER -U P M ODES 6-15 S t arting the computer by p assword To start up the computer with the user password, follow these steps: 1 . Turn on the power as described in Chapter 3, Getting Started . The following message appears: Password = NOTE: At this point, the hotkeys Fn + F1 to F5 do not work. They will function after you enter the p[...]

6-16 User's Manual P OWER AND P OWER -U P M ODES Panel power off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. NOTE: If the panel power off function is enabled and you use Shut down Windows, do not[...]

HW S ETUP Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7 - 1 Accessing HW Setup ......................................................................... 7 - 1 HW Setup window .............................................................................. 7 - 1 [...]

HW S ETUP[...]

7-1 HW S ETUP AND P ASSWORDS Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer. NOTE: If the supervi[...]

User's Manual 7-2 HW S ETUP AND P ASSWORDS General This window displays the BIOS version and contains two buttons: Default and About . Setup This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings. About Click About to display the HW Setup version. Password User Password This optio[...]

7-3 HW S ETUP AND P ASSWORDS 4 . If character strings match, the password is registered and the display changes to: The password was registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1 . Select Not Registered to display the following prompt: Enter Password: 2 . Ent[...]

User's Manual 7-4 HW S ETUP AND P ASSWORDS Key FD After you set a password, you can create a Key FD (diskette). If you forget the user password, the Key FD lets you bypass the password function. NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost. To create a Key FD follow the steps below. 1 . Turn off th[...]

7-5 HW S ETUP AND P ASSWORDS Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional . ECP Sets the port type to Extended Capabilities Port ([...]

User's Manual 7-6 HW S ETUP AND P ASSWORDS Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically CPU power consumption and clock speed Switchable automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) Always High CPU power[...]

7-7 HW S ETUP AND P ASSWORDS To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2 . The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD, Network (LAN), PC (ATA) card boot. NOTE: A bar will appear only under the selected device. 3 . Use the left/right cursor keys to highligh[...]

User's Manual 7-8 HW S ETUP AND P ASSWORDS HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD −> −> −> −> −> PC Card (Default) HDDs are searched for[...]

7-9 HW S ETUP AND P ASSWORDS USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled . Enabled Enables the USB KB/Mouse Legacy Emulation. (Default) Disab[...]

User's Manual 7-10 HW S ETUP AND P ASSWORDS Supervisor p assword Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:Program FilesTOSHIBAWindows UtilitiesSVPWTool . In the SVPWTool directory, open the readme.htm file.[...]

O PTIONAL D EVICES Chapter 8 Optional Devices PC cards ............................................................................................. 8 - 2 Inserting a PC card ............................................................................. 8 - 2 Removing a PC card ........................................................................[...]

O PTIONAL D EVICES[...]

8-1 O PTIONAL D EVICES Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ❑ PC cards ❑ Memory expansion Power devices ❑ Battery pack ❑ Universal AC adap[...]

User's Manual 8-2 O PTIONAL D EVICES PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC card[...]

8-3 O PTIONAL D EVICES Removing a PC card To remove the PC card, follow the steps below. 1 . Click the Safety Remove Hardware icon on the Task Bar. 2 . Click PC card . 3 . Press the PC card eject button to extend it. 4 . Press the extended eject button to pop the card out slightly. 5 . Pinch the PC card and remove it. Figure 8-2 Removing the PC car[...]

User's Manual 8-4 O PTIONAL D EVICES Memory exp ansion You can install additional memory in the computer’s memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. CAUTION: 1. Use only memory modules approved by TOSHIBA. 2. Do not try to install or remove a memory module under the [...]

8-5 O PTIONAL D EVICES Memory expansion Figure 8-3 Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module’s connectors into the computer’s connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection. CAUTION: Do not touch the connectors on the memory module or on the compute[...]

User's Manual 8-6 O PTIONAL D EVICES Figure 8-4 Installing the memory module 8. Seat the cover and secure it with a screw. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes . 10. Turn the power on and make sure the added memory is recognized. Open System Properties in the Control Panel and click the General tab. R[...]

8-7 O PTIONAL D EVICES Figure 8-5 Removing the memory module 6 . Seat the cover and secure it with a screw and replace the battery pack. Battery p ack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. [...]

User's Manual 8-8 O PTIONAL D EVICES External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1 . Turn the computer off. 2 . Connect the monitor to the external monitor port. 3 . Turn the monitor?[...]

8-9 O PTIONAL D EVICES TV e. Select Television icon. f . Select the Video Standard list box and select the format that your TV supports. *Please select one of them, NTSC-M, NTSC-J or PAL-B from the Video Standard list box though there are lots of selections. Changing the resolution to 640x480 for TV If you want to change the resolution into 640x480[...]

User's Manual 8-10 O PTIONAL D EVICES Figure 8-7 The Adapter window (4 ) Select a resolution from the menu. Figure 8-8 Resolution menu[...]

8-11 O PTIONAL D EVICES Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the back side of the computer. Figure 8-9 Security lock Security lock[...]

User's Manual 8-12 O PTIONAL D EVICES[...]

T ROUBLESHOOTING Chapter 9 T roubleshooting Problem solving process ................................................................... 9 - 1 Preliminary checklist .......................................................................... 9 - 1 Analyzing the problem ........................................................................ 9 - 2 Hard[...]

T ROUBLESHOOTING[...]

9-1 T ROUBLESHOOTING Chapter 9 T roubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Re[...]

User's Manual T ROUBLESHOOTING 9-2 ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify t[...]

9-3 T ROUBLESHOOTING Hardware If you cannot find a software problem, check your hard- ware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section di[...]

User's Manual T ROUBLESHOOTING 9-4 Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot P[...]

9-5 T ROUBLESHOOTING Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally shut down. Problem P rocedure Computer shuts down Leave the computer off until the computer and DC IN indicator reaches room temperature, then turn it back on. flashes orange If the computer is still too warm, the[...]

User's Manual T ROUBLESHOOTING 9-6 Battery If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicator and battery operation see Chapter 6, Power and Power-Up Modes . Problem Procedure Battery doesn’t The battery may be discharged. Connect the power the computer universa[...]

9-7 T ROUBLESHOOTING Hardware and system checklist Password Problem P rocedure Cannot enter Contact your dealer. or forgot password NOTE: For information on setting a password, refer to Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, The Keyboard . P[...]

User's Manual T ROUBLESHOOTING 9-8 • The way to replace the key-top Press the key-top until you hear a click after removing a metal spring from the key-top, hooking it to projecting parts and aligning the center of the key-top. Enter, Back Space, Shift and Space key P RESS FROM THE UPSIDE P ROJECTING P ART P ROJECTING P ART S PRING P ROJECTI[...]

9-9 T ROUBLESHOOTING • Follow the steps below when a plastic spring is out of place together with a key- top. 1. Remove the plastic spring from the key-top. 2. Attach the plastic spring to the key board with its flat face downward after confirming the direction. Hardware and system checklist F LAT FACE DOWNWARD[...]

User's Manual T ROUBLESHOOTING 9-10 3. Press from the upside until you hear a click after replacing the key-top to the right position. LCD p anel Problem P rocedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on They might have come from contact with the [...]

9-11 T ROUBLESHOOTING Hard disk drive Problem P rocedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD-ROM is in the optical media drive. Remove drive any diskette and/or CD-ROM and check Boot priority. Refer to Chapter 7, Boot Priority . There may be a problem with your operating system files. Refer to [...]

User's Manual T ROUBLESHOOTING 9-12 A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleani[...]

9-13 T ROUBLESHOOTING DVD-ROM drive For more information, refer to Chapter 4, Operating Basics . Problem P rocedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing [...]

User's Manual T ROUBLESHOOTING 9-14 Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: C D- D A, CD - Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD- EXTRA), CD-G (Audio CD only), Addressing Method 2 Check the region code on the DVD. I[...]

9-15 T ROUBLESHOOTING Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem. Make sure the others do not hardware configuration match[...]

User's Manual T ROUBLESHOOTING 9-16 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording. • Do not run or start other software[...]

9-17 T ROUBLESHOOTING Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem. Make sure the others do not hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: C D- D A, CD - [...]

User's Manual T ROUBLESHOOTING 9-18 Diskette drive For more information, refer to Chapter 4, Operating Basics . Problem Pr ocedure Drive does not There may be a faulty cable connection. Check operate the connection to the computer and to the drive. You cannot access Try another diskette. If you can access the the external 3 1/2" diskette,[...]

9-19 T ROUBLESHOOTING Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem P rocedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume Pad operation it[...]

User's Manual T ROUBLESHOOTING 9-20 USB mouse Problem Pr ocedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume mouse operation its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking Try changing the d[...]

9-21 T ROUBLESHOOTING USB Refer also to your USB device’s documentation. Problem P rocedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documenta- tion for information on checking the drivers. [...]

User's Manual T ROUBLESHOOTING 9-22 Sound system Refer also to documentation for your audio devices. Problem Pr ocedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices ,[...]

9-23 T ROUBLESHOOTING Modem Refer to the online help files for Appendix C and D . Problem P rocedure Communication Make sure the computer’s internal modem software can’t settings are correct. Refer to Phone and Modem initialize modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but c[...]

User's Manual T ROUBLESHOOTING 9-24 Character display In data transmission, make sure the parity bit becomes garbled and stop bit settings correspond with those during a of the remote computer. communication Check the flow control and communication protocol. You cannot receive Check the rings before auto answer setting in an incoming call your[...]

9-25 T ROUBLESHOOTING Wireless LAN If the following procedures do not restore LAN access, consult your LAN adminis- trator. For more information on wireless communication, refer to Chapter 4, Operat- ing Basics . Problem P rocedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. If problems persist,[...]

User's Manual T ROUBLESHOOTING 9-26 China TOSHIBA Computer Systems (Shanghai) Co., Ltd. Bldg. 33, No. 351, Jinzang Road, Pudong New Area, Shanghai, P.R. China 201206 Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01 Alexandra Technopark Singapore 119968 TOSHIBA support If you require any additional help using your computer or if[...]

9-27 T ROUBLESHOOTING United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA In Europe Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany France TOSHIBA Systèms France S.A. 7, Rue Ampère B.P. 131, 92804 Pu[...]

User's Manual T ROUBLESHOOTING 9-28[...]

A PPENDIXES Appendixes Appendix A Specifications ........................................................................... A - 1 Appendix B Display Controller and Modes .............................................. B - 1 Appendix C AT Commands .......................................................................... C - 1 Appendix D S-registers[...]

A PPENDIXES[...]

A PPENDIX A A-1 Appendix A S pecifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 332 (w) x 293 (d) x 33/40 (h) millimeters (not including parts that extend beyond the main body) Weight 2.9 kilograms, configured with: 15"XGA-TFT, CD-RW/ DVD-ROM drive, Modem, Wireless LAN Weight will vary wi[...]

A PPENDIX A A-2 User's Manual Built-in Modem Network control unit (NCU) Type of NCU A A Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: Full duplex system Fax: Half duplex Communication Data p[...]

B-1 A PPENDIX B Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the[...]

User's Manual B-2 A PPENDIX B Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, if your software supports both grap[...]

B-3 A PPENDIX B Appendix B Table1 Video modes (VGA) continued Video Type Resolution Character L C D CRT Scanning mode matrix colors colors frequency (pels) Vertical (Hz) D VGA 320 x 200 8 x 8 16 of 256K 16 of 256K 70 Grph Pels E VGA 640 x 200 8 x 8 16 of 256K 16 of 256K 70 Grph Pels F VGA 640 x 350 8 x 14 Mono Mono 70 Grph Pels 10 VGA 640 x 350 8 x[...]

User's Manual B-4 A PPENDIX B Table 2 Video modes (XGA) Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K 256/256K 60 (Virtual) 75 85 100 1400 x 1050 256/256K 256/256K 60 (Virtual) 75 85 160[...]

B-5 A PPENDIX B Appendix B Table 2 Video modes (XGA) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K 64K/64K 60 (Virtual) 75 85 100 1400 x 1050 64K/64K 64K/64K 60 (Virtual) 75 85 1600 x 1200[...]

User's Manual B-6 A PPENDIX B Table 2 Video modes (XGA) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 16M/16M 16M/16M 6 0 75 85 100 800 x 600 16M/16M 16M/16M 6 0 75 85 100 1024 x 768 16M/16M 16M/16M 6 0 75 85 100 1280 x 1024 16M/16M 16M/16M 60 (Virtual) 75 85 100 1400 x 1050 16M/16M 16M/16M 60 (Virtual) 75 85 [...]

B-7 A PPENDIX B Table 3 Video modes (Super XGA+) Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K 256/256K 60 75 85 100 1400 x 1050 256/256K 256/256K 60 75 85 1600 x 1200 256/256K 256/256K 60 (V[...]

User's Manual B-8 A PPENDIX B Table 3 Video modes (Super XGA+) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K 64K/64K 60 75 85 100 1400 x 1050 64K/64K 64K/64K 60 75 85 1600 x 1200 64K/[...]

B-9 A PPENDIX B Appendix B Table 3 Video modes (Super XGA+) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 16M/16M 16M/16M 6 0 75 85 100 800 x 600 16M/16M 16M/16M 6 0 75 85 100 1024 x 768 16M/16M 16M/16M 6 0 75 85 100 1280 x 1024 16M/16M 16M/16M 60 75 85 100 1400 x 1050 16M/16M 16M/16M 60 75 85 1600 x 1200 16M/16M 1[...]

User's Manual B-10 A PPENDIX B[...]

C-1 A PPENDIX C Appendix C A T Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT [...]

User's Manual C-2 A PPENDIX C A Answer command This command instructs the modem to go off-hook and answer an incoming call. B n Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). [...]

C-3 A PPENDIX C ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S = n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. E n Echo command This command controls whether or not the characters [...]

User's Manual C-4 A PPENDIX C L n Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0 ) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode This command turns the speaker on or off. M0 The speaker is off. M1 The spe[...]

C-5 A PPENDIX C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Re[...]

User's Manual C-6 A PPENDIX C T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. V n DCE response format This command controls whether result codes (including call progress and negotiation progress me[...]

C-7 A PPENDIX C X 5 Enable Enable O K , R I NG , NO CARRIER, ERROR, NODIAL TONE, BUSY , CONNECT <RA TE>, RRING , NO BONGTONE, DELA YED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The m odem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone[...]

User's Manual C-8 A PPENDIX C &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise & D n DTR control This command interprets how[...]

C-9 A PPENDIX C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard [...]

User's Manual C-10 A PPENDIX C &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result [...]

C-11 A PPENDIX C Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. N0 Buffer mode. No error control. N1 Direct mode. N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also [...]

User's Manual C-12 A PPENDIX C Vn Protocol result code V0 Disable protocol result code appended to DCE speed. V1 Enable protocol result code appended to DCE speed (default). Result Codes: OK n=0,1 ERROR Otherwise % B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted i[...]

D-1 A PPENDIX D Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails. You can also customize certain AT commands such as the escape [...]

User's Manual D-2 A PPENDIX D S 0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: rings S 1 Rin[...]

D-3 A PPENDIX D S 4 Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: A SC II S 5 Command line editing character (user defined) This [...]

User's Manual D-4 A PPENDIX D S 7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer). In originate mode, the timer is reset upon detection of an answer to[...]

D-5 A PPENDIX D S3 7 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 r eserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 r eserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 120 00 bps S37 = 11 144 00 bps S37 = 12 168 00 bps S37 = 13 192 00 bps S37 = 14 216 00 bps S37 = 15 240 00 bps[...]

User's Manual D-6 A PPENDIX D A T command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description O K 0 Command executed CONNECT 1 Modem connected to line R I N G 2 A ring signal has been detected NO CARRIER 3 Modem lost carrier signal, or does not detect carrier signal, or does not [...]

D-7 A PPENDIX D Result Code Numeric Description DELAYED* 2 8 8 Delay is in effect for the dialed number BLACKLISTED* 2 8 9 Dialed number is blacklisted BLACKLIST FULL* 2 9 0 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error c[...]

User's Manual D-8 A PPENDIX D[...]

E-1 A PPENDIX E Appendix E V .90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary c[...]

User's Manual E-2 A PPENDIX E Table E-1 Result codes for a V.90 connection No. Result code Description 7 0 CONNECT 32000 EC* Connection at 32000 bps 7 2 CONNECT 36000 EC* Connection at 36000 bps 7 4 CONNECT 40000 EC* Connection at 40000 bps 7 6 CONNECT 44000 EC* Connection at 44000 bps 7 8 CONNECT 48000 EC* Connection at 48000 bps 8 0 CONNECT [...]

E-3 A PPENDIX E * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V 4 2 V.42 error control only NoEC N o error control protocol [...]

User's Manual E-4 A PPENDIX E[...]

F-1 A PPENDIX F Appendix F Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Inst alling the internal modem NOTE: The internal modem is preinstalled. The following i[...]

F-2 User's Manual A PPENDIX F 9 . Secure the cover with one screw. Removing the internal modem To remove the internal modem, follow the steps below. 1 . Save your data and turn off the computer. 2 . Disconnect the AC adaptor and any other peripheral device. 3 . Turn the computer upside down and remove the battery pack. 4 . Remove one screw sec[...]

G-1 A PPENDIX G Appendix G Wireless LAN Card Specifications Form Factor - Mini PCI TypeIII Capability - I EEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance. Network Operating - Microsoft Windows® Networking System Media [...]

G-2 User's Manual A PPENDIX G - Band2.4GHz (2400-2483.5 MHz) (Revision B) Modulation Technique - DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) - OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM- 64QAM (Revision A, Turbo Mode) The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at lower Transmit [...]

G-3 A PPENDIX G When installing Wireless LAN Cards, the channel configuration is managed as follows: ❑ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can[...]

G-4 User's Manual A PPENDIX G Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850 MHz Note Channel ID 42 5210 U S only *1 50 5250 U S only *1 58 5290 U S only *1 152 5760 U S only *1 160 5800 U S only *1 *1: Available Area: US (USA, CANADA) only[...]

H-1 A PPENDIX H Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm 2 Current r[...]

H-2 User's Manual A PPENDIX H The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada United Kingdom Australia Europe BS approved UL approved CSA approved AS approved Approved by the appropriate agency[...]

A PPENDIX I I-1 Appendix I Part s Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, and communication devices.[...]

User’s Manual A PPENDIX I Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice. Celeron 1.80 C1.80 14"TFT-XGA 14X 128[...]

Glossary-1 G LOSSARY Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP : accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic [...]

Glossary-2 G LOSSARY analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical discipline[...]

Glossary-3 G LOSSARY B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system com- mands or executable files. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers[...]

Glossary-4 G LOSSARY capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. card: Synonym for board . See board. CardBus: An industry standard bus for 32-bit P[...]

Glossary-5 G LOSSARY components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instruc- tions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. c[...]

Glossary-6 G LOSSARY device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that ra[...]

Glossary-7 G LOSSARY escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction. Extended Capability Port: An industry standard that provides a data [...]

Glossary-8 G LOSSARY computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits info[...]

Glossary-9 G LOSSARY coating is etched into character forming segments with leads that extend to the edge of the glass. Applying a voltage between the glass sheets alters the brightness of the liquid crystal. LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip. 2) An integrate[...]

Glossary-10 G LOSSARY permanently storing information. Turning the computer’s power off does not alter data stored in nonvola- tile memory. numeric keypad overlay: A feature that allows you to use certain keys on the keyboard to perform numeric entry, or to control cursor and page move- ment. O OCR: Optical Character Recognition (reader). A techn[...]

Glossary-11 G LOSSARY P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relation- ship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detec[...]

Glossary-12 G LOSSARY S SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD cards: Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assis- tants. SIO: Serial Input/Output. The electronic methodology[...]

Glossary-13 G LOSSARY subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels indepen- dently, each may emit a different degree of brightness. See also pixel. synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that ha[...]

Glossary-14 G LOSSARY Glossary[...]

Index Index-1 I NDEX Index location of vents 2-2 settings 4-24 CPU, See Processor D Diskette drive 1-3 using 4-2 view 2-10 Display 1-5, 2-7 automatic power off 1-8 brightness decrease 5-5 brightness increase 5-6 opening 3-6 problems 9-10 selection 5-5 Documentation list 1-2 Drag'n Drop CD+DVD 1-10, 4-14 DVD Video Player 1-10 DVD-ROM drive 1-4,[...]

User's manual Index-2 I NDEX work habits 3-4 Expansion memory, See Memory F Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5 Fn + F7 ([...]

Index Index-3 I NDEX L LAN 1-7 connecting 4-22 disconnecting 4-22 jack 2-5 LAN active indicator 2-4 link indicator 2-5 problems 9-24 LCD, See Display, Video modes and Monitor external Level 2 cache, See Cache memory Lock security, See Security lock M Media care CD/DVDs 4-15 diskettes 4-15 Memory 1-3 expansion 1-11, 8-4 installing 8-4 problems 9-21 [...]

User's manual Index-4 I NDEX keyboard 9-7 LAN 9-24 LCD panel 9-10 memory expansion 9-21 modem 9-23 monitor external 9-22 mouse, USB 9-20 overheating power down 9-5 password 9-7 PC card 9-18 pointing device 9-19 power 9-4 real time clock 9-25 self test 9-4 sound system 9-22 support from TOSHIBA 9-26 system start-up 9-3 Touch Pad 9-19 USB 9-21 W[...]

Index Index-5 I NDEX Wireless LAN 1-7 problems 9-25 using 4-19[...]