Toshiba SATELLITE PRO S200 manuel d'utilisation

[CONFIDENTIAL] Toshiba Personal Computer TECRA A9 Series ( TECRA S5 / TECRA P5 /Satellite Pro S200 ) Maintenace Manual TOSHIBA CORPORATION File Number 960-633[...]

ii [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Copyright © 2007 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Toshib[...]

TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer TECRA A9,S5,P5,Satellite Pro S200. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs)[...]

iv [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the TECRA A9,S5,P5, Satellite Pro S200 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes ho[...]

TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only [...]

vi [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ... 1-1 1.2 System Unit Block Diagram .....................................................................[...]

TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] vii Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... 3-4[...]

viii [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Chapter 4 Replacement Procedures 4.1 Overview ................................................................................................................... 4-1 4.2 Battery pack .................................................................................................[...]

TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] ix Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ................................................................................................ B-1 Appendix C Pin Assignments.....[...]

x [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[...]

[CONFIDENTIAL] Chapter 1 Hardware Overview[...]

1 Hardware Overview 1-ii [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[...]

1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-iii Chapter 1 Contents 1.1 Features................................................................................................................... ....1-1 1.2 System Unit Block Diagram ..........................................................................[...]

1 Hardware Overview 1-iv [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Figures Figure 1-1 Front of the computer ....................................................................................1- 6 Figure 1-2 System un it configuration..............................................................................1- 7 Figure 1-3[...]

1.1 Features 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-1 1.1 Features The Toshiba TECRA A9(S5,P5,Satellite Pro S200) Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Sem iconductor (CMOS) technology extensively to provide compact size, minim um weight, low pow[...]

1 Hardware Overview 1.1 Features 1-2 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)  HDD The computer has a 2.5-inch SATA HDD. The following capacities are available. • • • /80/100/120/160 GB  USB FDD A 3.5-inch USB FDD accommodates 2HD (1.44MB) or 2DD (720KB) disks.  Optical Drive A CD-ROM drive, DVD-ROM&CD-R/[...]

1.1 Features 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-3  Universal Serial Bus (USB2.0) Three USB ports are provided. The ports comply with the USB2.0 standard, which enables data transfer speeds 40 times faster than USB1.1 standard. USB1.1 is also supported.  IEEE 1394 port The computer comes with[...]

1 Hardware Overview 1.1 Features 1-4 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)  Docking interface port The docking interface port enables connection of an optional Express Port Replicator. It provides additional features as follows: • RJ45 LAN jack • External monitor port • DC IN 15V jack • Security lock slot • [...]

1.1 Features 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-5  Internal modem The computer contains a MDC, enabling data and fax comm unication. It supports ITU-T V.90 (V.92). The transfer rates are 56 Kbps for data reception, 33.6 Kbps for data transmission, and 14,400 bps for fax transmission. However, t[...]

1 Hardware Overview 1.1 Features The front of the computer is shown in figure 1-1. Figure 1-1 Front of the computer 1-6 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[...]

1.1 Features 1 Hardware Overview The system unit configuration is shown in figure 1-2. Figure 1-2 System unit configuration TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-7[...]

1 Hardware Overview 1.2 System Unit Block Diagram 1.2 System Unit Block Diagram Figure 1-3 is a block diagram of the system unit. Figure 1-3 System unit block diagram 1-8 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[...]

1.2 System Unit Block Diagram 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-9 The system unit is composed of the following m ajor components:  Processor • Intel ® Core TM 2 Duo Processor • Core speed: • • 2.40GHz (T7700) /2.20GHz (T7500) / 2.00GHz (T7300) In the case of Processor which built in 4[...]

1 Hardware Overview 1.2 System Unit Block Diagram 1-10 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)  Intel 965GM/GML (Crestline-GM (North Bridge)) • Features: – Meorom Processor System Bus Supports – PCI Express Based Graphics Interface – System Memory supports :DDR2-533 ／ DDR2-667, 4GB m ax. – DMI(Direct Media In[...]

1.2 System Unit Block Diagram 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-11  Cardbus controller (TI PCI8412ZHK) − PCI Interface(PCI Rev.2.2) − SD IO Controller(Ver.1.1) − CardBus / Ultra media Controller (Yenta Ver.2.2:1 socket) − SD/MMC(SDHC Ver. 1.2 revised edition) , Memory Stick, Memory Sti[...]

1 Hardware Overview 1.2 System Unit Block Diagram 1-12 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)  PSC (Power Supply Controller) • One TMP86FS49AUG chip is used. • This controller controls the power sources.  Clock Generator • IDT 9LPR501PGLFT is used. • This device generates the system clock.  Modem Controlle[...]

1.2 System Unit Block Diagram 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-13  Wireless LAN • One PCI-Ex MiniCard • Intel Kedron a/b/g or a/b/g/n • Supports Wireless Comm unication SW • Supports W-LAN via PCMCIA (Euro : GSM/GPRS)  Super I/O • SMSC LPC47N217 -JV chip is used. • This gate ar[...]

1 Hardware Overview 1.3 3.5-inch Floppy Disk Drive (USB External) 1.3 3.5-inch Floppy Disk Drive (USB External) The 3.5-inch FDD is a thin, high-performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD is shown in figure 1-4. The specifications for the FDD are listed in Table 1-1. Figure 1-4 3.5-inch [...]

1.4 2.5-inch Hard Disk Drive 1 Hardware Overview 1.4 2.5-inch Hard Disk Drive The removable HDD is a random access non-volatile storage device. It has a non-rem ovable 2.5-inch magnetic disk and mini-W inchester type magnetic heads. The computer supports a 80GB, 120GB or 160GB. The HDD is shown in figure 1-5. Specifications are listed in Table 1-2.[...]

1 Hardware Overview 1.5 Optical Drive (ODD) 1-16 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 1.5 Optical Drive (ODD) 1.5.1 CD-ROM Drive The CD-ROM drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD-ROM. The specifications of the CD-ROM are described in Table 1-2. Table 1-2 CD-ROM drive specifications Specificati[...]

1.5 Optical Drive (ODD) 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-17 1.5.2 DVD-ROM & CD-R/RW Drive The DVD-ROM & CD-R/RW drive accomm odates either 12 cm (4.72-inch) or 8 cm (3.15- inch) CD-ROM, DVD-ROM and CD-R/RW. The specifications of the DVD-ROM & CD-R/RW drive are described in Table 1-4.[...]

1 Hardware Overview 1.5 Optical Drive (ODD) 1-18 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 1.5.3 DVD-Super Multi Drive The DVD Super Multi drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD-ROM, DVD-ROM, CD-R, CD-RW, DVD-R, DVD+R, DVD-RW, DVD+RW , DVD- RAM, DVD-R DL and DVD+R DL. The specifications are listed [...]

1.6 Keyboard 1 Hardware Overview 1.6 Keyboard The keyboard is mounted 85(US)/87(UK) keys that consist of character key and control key, and in conformity with JIS. The keyboard is connected to mem brane connector on the system board and controlled by the keyboard controller. Figure 1-6 is a view of the keyboard. See Appendix E about a layout of the[...]

1 Hardware Overview 1.7 TFT Color Display 1.7 TFT Color Display The TFT color display consists of 15.4-inch WXGA/WXGA+ LCD m odule and FL inverter board. 1.7.1 LCD Module The LCD module used for the TFT color display uses a backlight as the light source and can display a maximum of 16M colors with 1,280 x 800 or 1,680x1050 resolution. The Intel Cre[...]

1.7 TFT Color Display 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-21 1.7.2 FL Inverter Board The FL inverter board supplies a high frequency current to illuminate the LCD module. Table 1-5 lists the FL inverter board specifications. Table 1-5 FL inverter board specifications Item Specifications G71C0006A11[...]

1 Hardware Overview 1.8 Power Supply 1-22 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 1.8 Power Supply The power supply supplies many different voltages to the system board and perform s the following functions: 1. Judges that the DC power supply (AC adapter) is connected to the computer. 2. Detects DC output and circuit malfun[...]

1.8 Power Supply 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-23 Table 1-6 Power supply output rating (1/4) Use Voltage (V) Name CK-EYV M-E3V Clock Gen 3.3 P3V 1.05 1R05-P1V 1.5 1R05-P1V CPU 0.55-1.325 PPV 1.05 1R05M-E1V 1.05 1R05-P1V 1.25 1R25M-E1V 1.25 1R25-P1V 1.5 1R5-P1V 1.8 1R8-B1V 1.05 IGD-PGV (G)MCH [...]

1 Hardware Overview 1.8 Power Supply 1-24 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table 1-6 Power supply output rating (2/4) Use Voltage (V) Name 3.3 P3V 5 P5V 3.3 SB-P3V ODD 5 SB-P5V 3.3 P3V HDD 5 P5V Card Cont. 3.3 P3V 3.3 MCVCCA-PYV PC Card 5 MCVPPA-PYV 5 P5V PC Card PS 3.3 P3V SD Card 3.3 FM-P3V SD Card PS 3.3 P3V 1.5 C[...]

1.8 Power Supply 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-25 Table 1-6 Power supply output rating (3/4) Use Voltage (V) Name SIM Card 3.3 UIMPWR-E3V 1.5 1R5-P1V Robson 3.3 P3V SPI 3.3 LAN-E3V MDC 3.3 E3V EC/KBC 3.3 S3V Touch Pad 5 SP-P5V LED 5 M5V 3.3 E3V TPM 3.3 P3V Accelerometer 3.3 S3V 3.3 FS-E3V Fin[...]

1 Hardware Overview 1.8 Power Supply 1-26 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table 1-6 Power supply output rating (4/4) Use Voltage (V) Name 1.2 1R2-P1V 1.8 1R8-P1V 3.3 P3V GPU 1.0-1.1 PGV VRAM 1.8 1R8-P1V 5 FL-P5V LCD 3.3 PNL-P3V 5 P5V LCD PS 3.3 P3V DVI Transmitter 2.5 2R5-P2V 4.7 A4R7-P4V AMP 5 SND-P5V 4.7 A4R7-P4V [...]

1.9 Batteries 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-27 1.9 Batteries The computer has three types of batteries as follows:  Main battery pack  RTC battery The battery specifications are listed in Table 1-7. Table 1-7 Battery specifications Battery name Material Output voltage Capacity battery G[...]

1 Hardware Overview 1.9 Batteries 1-28 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 1.9.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The microprocessor controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer. Th[...]

1.9 Batteries 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-29 1.9.3 RTC battery The RTC battery provides power to keep the current date, time and other setup information in memory while the com puter is turned off. Table 1-9 lists the charging time and data preservation period of the RTC battery. Table 1-9 [...]

1 Hardware Overview 1.10 AC Adapter 1-30 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 1.10 AC Adapter The AC adapter is also used to charge the battery. Table 1-10 lists the AC adapter specifications. Table 1-10 AC adapter specifications Parameter Specification G71C0006Q210 (2-pin) G71C0006R210 (3-pin) Power 75W (Peak 90W) Input[...]

1.10 AC Adapter 1 Hardware Overview TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 1-31[...]

[CONFIDENTIAL] Chapter 2 Troubleshooting Procedures[...]

2 Troubleshooting Procedures 2-ii [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[...]

2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 2-iii Chapter 2 Contents 2.1 Troubleshooting ..........................................................................................................2- 1 2.2 Troubleshooting Flowchart ......................................................................[...]

2 Troubleshooting Procedures 2-iv [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 2.8 Display Troubleshooting ..........................................................................................2-42 Procedure 1 External Monitor Check .............................................................2-42 Procedure 2 Diagnostic Tes[...]

2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] 2-v 2.16 Fingerprint sensor Troubleshooting .........................................................................2-59 Procedure 1 Setting Windows Log-ON password .........................................2-60 Procedure 2 Registrati on of fingerprint....[...]

2 Troubleshooting Procedures 2-vi [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Figures Figure 2-1 Troubleshooti ng flowchart ..................................................................................2-3 Figure 2-2 Printer port LED board ....................................................................................[...]

2.1 Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-1 2 2.1 Troubleshooting Chapter 2 describes how to determine if a Fi eld Replaceable Unit (FRU) in the com puter is causing the computer to malfunction. The FRUs covered are: 1. Power Supply 6. Display 11. Wireless LAN 2. System Boa[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2-2 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determ ining which FRU malfunctions. Before going through the flowchart steps, check the following:  Ask the user if a password is registe[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (1/2) TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-3[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (2/2) 2-4 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633)[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-5 If the diagnostics program cannot detect an erro r, the problem may be intermittent. The Running Test program should be executed severa l times to isolate the problem . Check the Log Utilities function to confirm which d[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-6 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) 2.3 Power Supply Troubleshooting The power supply controls many functions and components. To determ ine if the power supply is functioning properly, star t with Procedure 1 and continue with the other Procedures as [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-7 Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Table 2-3 Error code Error cod[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-8 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) Check 1 Compare the patterns in the hexadeci mal error code to the tables below.  AC Adaptor Error code Meaning 10h AC Adaptor output voltage is over 16.5V. 11h Express Port Replicator voltage is ove r 16.5V. 12h[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-9  1R5-C1V output (P62) Error code Meaning 60h 1R5-C1V voltage is over 2.15V wh en the computer is powered on/off. 61h 1R5-C1V voltage is 1.275V or less when the computer is powered on. 62h 1R5-C1V voltage is 1.275V [...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-10 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633)  1R9-B1V output (P66:MUX- CH0) Error code Meaning A0h 1R9-B1V voltage is over 2.40V when the computer is powered on/off. A1h 1R9-B1V voltage is 1.53V or less when the com puter is powered on. A2h 1R9-B1V voltage [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-11  1R9-B1V output (P66:MUX- CH1) Error code Meaning E0h 1R9-B1V voltage is over 2.40V when the computer is powered on/off. E1h 1R9-B1V voltage is 1.53V or less when the com puter is powered on. E2h 1R9-B1V voltage i[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-12 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Check 2 In the case of error code 10h or 12h:  Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If the cables are connected correctly, go to the follo[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connection Check The power supply wiring diagram is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from the wall outlet. Check the power cable for breaks. If the power cord is damaged, c onnect a new AC power cord[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-14 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Procedure 4 Charge Check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the pow er. If you cannot turn on the [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-15 Procedure 5 Replacement Check The system board processor module m ay be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures . Check the connection betw[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-16 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) 2.4 System Board Troubleshooting This section describes how to determ ine if th e system board and CPU are defective or not functioning properly. Start with Procedure 1 an d continue with the other procedures as ins[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-17 Procedure 1 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it.  If an error[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-18 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Check 2 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) th rough (17), (22) or (23) appears, go to Procedure 4[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Procedure 2 Serial Port Check (Boot Mode) Check the D port status by a serial port test. Th e tool for serial port test is shown below. Figure 2-2 A set of tool for serial port test The test procedures are follows: 1. Connect the RS-232C cross-cable to th e connector CN34200 of the syste[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-20 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Table 2-5 Serial port (Boot mode) error status (1/9) D port Status Test item Contents Boot Block Permission of A20 and clear of software reset bit Prohibition of APIC Initialization of MCH, ICH Initialization of Sup[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-21 Table 2-5 Serial port (Boot mode) error status (2/9) D port Status Test item Contents F0B9h Saving of key scan code Setting of TASK_1ms_TSC FAN control Sound initialization (for BEEP sound) System speaker permission [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-22 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Table 2-5 Serial port (Boot mode) error status (3/9) D port Status Test item Message Renewal of a microcode （ Only support model ） Prohibition of cache Permission of L1/L2 cache in FlashROM area Initialization o[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-23 Table 2-5 Serial port (Boot mode) error status (4/9) D port Status Test item Contents (F103h) Check of memory configuration change (Resume error LED=73H) RAM area checksum check in system BIOS (Resume error LED=79H) [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-24 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Table 2-5 Serial port (Boot mode) error status (5/9) D port Status Test item Contents (F106h) Check of parameter block A Permission of SMI except auto-off function Control of e xcess of rated input power Battery dis[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-25 Table 2-5 Serial port (Boot mode) error status (6/9) D port Status Test item Contents F108h PCI bus initialization (connection of DS Bus) Initialization of LAN information WakeUp factor check F109h Task generation fo[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-26 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Table 2-5 Serial port (Boot mode) error status (7/9) D port Status Test item Contents F10Fh INIT_SYSTEM (Initialization of system) Storing of CMOS error information to IRT_ERR_STS_B UF Timer initialization start EC [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-27 Table 2-5 Serial port (Boot mode) error status (8/9) D port Status Test item Contents (F11Dh) I/O LOCK Processing (For models supporting I/O LOCK) Opening of BM (Only model which is supporting the finger point leader[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-28 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Table 2-5 Serial port (Boot mode) error status (9/9) D port Status Test item Contents (F11Fh) HW initialization befo re Boot, Waiting for initialization completion Notifies the DVI connection status to VGA BIOS (For[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-29 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Di agnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more inform ation on how to perform these tests. 1. Syste[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-30 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Procedure 4 Replacement Check The system board connectors may be disconnect ed. Disassemble the com puter following the steps described in Chapter 4, Replacement Procedures and perform Check 1. Check 1 Visually chec[...]

2.5 USB FDD Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-31 2.5 USB FDD Troubleshooting This section describes how to determine if the USB FDD is functioning properly. Perf orm the steps below starting with Procedure 1 a nd continuing with the other procedures as required. Procedu[...]

2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting 2-32 [CONFIDENTIAL] TECRA A9(S5/P5/ S200) Mainten ance Manual ( 960-633) Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, tu rn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation about th e diagnost[...]

2.5 USB FDD Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connector Check and Replacement Check The USB FDD is connected to the System Board. Check 1 When using the USB port, make sure the USB FDD cable is firmly connected to CN4612 , CN4611 or CN4610 on the System board. If any of the connections are loose, re connect firmly and repeat [...]

2 Troubleshooting Proce dures 2.6 HDD Troubleshooting 2-34 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) 2 2.6 HDD Troubleshooting This section describes how to determine if the HDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required. Procedure 1: M[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-35 Procedure 2 Partition Check Insert the Toshiba MS-DOS system disk and restart the computer with U key holding down. Perform the following checks: Check 1 Type C: and press Enter . If you cannot change to drive C, go to Check [...]

2 Troubleshooting Proce dures 2.6 HDD Troubleshooting 2-36 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) Procedure 3 Format Check The computer’s HDD is formatted using the low level format program and the MS-DOS FORMAT program. To format the HDD, start with Check 1 below and perform the other steps as required. Check 1 Form[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-37 Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more inform[...]

2 Troubleshooting Proce dures 2.6 HDD Troubleshooting Procedure 5 Connector Check and Replacement Check The HDD may be disconnected, or the HDD or the system board may be dam aged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the HDD is firmly connect[...]

2.7 Keyboard and Dual point Troubleshooting 2 Troubleshooting Procedure TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-39 2.7 Keyboard and Dual point Troubleshooting To determine if the computer’s keyboard or touch pad is functioning properly, perform the following procedures. Start with Procedure 1 an d continue with the ot[...]

2 Troubleshooting Procedures 2.7 Keyboard and Dual point Troubleshooting Procedure 2 Connector Check and Replacement Check The keyboard, Dual point or sensor/switc h board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: 1. If the keyboard[...]

2.7 Keyboard and Dual point Troubleshooting 2 Troubleshooting Procedure TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-41 Check 5 The system board may be dam aged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures .[...]

2 Troubleshooting Procedures 2.8 Display Troubleshooting 2.8 Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Te st Program Execution Check Proce[...]

2.8 Display Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-43 If the connection is loose, reconnect firmly and re start the computer . If there is st ill an error, go to Procedure 4. Procedure 4 Replacement Check The FL, FL inverter board, LCD module, and system board are connected [...]

2 Troubleshooting Procedures 2.9 Optical Drive Troubleshooting 2-44 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) 2.9 Optical Drive Troubleshooting This section describes how to determ ine if the optical drive (Super Mul ti drive) in the Slim Select Bay is functioning pr operly. Perform the steps below starting with Procedure[...]

2.9 Optical Drive Troubleshooting 2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The optical drive (Super Multi drive) is connected to the system board. The connecto rs may be disconnected from the system board or m ay be damaged. Disassemble the com puter following the steps described in Chapter 4, Replacement Proce[...]

2 Troubleshooting Procedures 2.10 Modem Troubleshooting 2-46 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) 2.10 Modem Troubleshooting This section describes how to determine if the computer’s modem is functioning properly. Perform the steps below starting with Procedure 1 and continui ng with the other procedures as require[...]

2.10 Modem Troubleshooting 2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The Modem is installed as a MDC (Modem Da ughter Card). If the modem malfunctions, there may be a bad connection between the MDC and the system board. Or the MDC, system board or their connectors might be damaged. Disassemble the computer follo[...]

2 Troubleshooting Procedures 2.11 LAN Troubleshooting 2.11 LAN Troubleshooting This section describes how to determine if the computer’s L AN is functioning properly. Perform the steps below starting with Procedure 1 and continue with the other procedures as required. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Ch[...]

2.12 Bluetooth Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-49 2.12 Bluetooth Troubleshooting This section describes how to determ ine if th e computer’s Bluetooth is functioning properly. Perform the steps below starting with Procedure 1 and continui ng with the other procedure[...]

2 Troubleshooting Procedures 2.12 Bluetooth Troubleshooting Procedure 2 Connection Check The Bluetooth function wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the Bluetooth mod[...]

2.12 Bluetooth Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-51 Procedure 3 Replacement Check The Bluetooth antenna, Bluetooth module, sound board and system board are connected to the circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for[...]

2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting 2-52 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) 2.13 Wireless LAN Troubleshooting This section describes how to determine if the computer’s Wireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other p[...]

2.13 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Procedure 2 Antenna Connection Check The wireless LAN wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the wireless[...]

2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting 2-54 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633) Procedure 3 Replacement Check The wireless LAN antenna, wireless LAN board a nd the system board are connected to the circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, f[...]

2.14 Sound Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-55 2.14 Sound Troubleshooting This section describes how to determine if the computer’s sound f unctions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures a[...]

2 Troubleshooting Procedures 2.14 Sound Troubleshooting Procedure 2 Connector Check The sound function-wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: 1. If the speakers do not work correctly, perf[...]

2.14 Sound Troubleshooting 2 Troubleshooting Procedures TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3)[CONFIDENTIAL ] 2-57 Procedure 3 Replacement Check Check 1 If the speakers do not sound properly, the speaker may be defective or damaged. Replace it with a new one. If the speake rs still do not work properly, go to Check 3. Check 2 If the Bu[...]

2 Troubleshooting Procedures 2.15 Bridge media Slot Troubleshooting 2.15 Bridge media Slot Troubleshooting This section describes how to determine if the computer's Bridge m edia functions are functioning properly. Perform the steps below star ting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Check on Win[...]

2.16 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures 2.16 Fingerprint sensor Troubleshooting CAUTION : To delete the account for confir ming the fingerprint operation, it is necessary to log on by the account wi th the management authority. If the password has been set to log on, ask the Log-ON password to the user. To check if the[...]

2 Troubleshooting Procedures 2.16 Fingerprint sensor Troubleshooting Procedure 1 Setting Windows Log-ON password 1. Open [User Account] from [Control Panel]. 2. Click [User Account]. 3. Click the icon of the account (user’s na me) that you want to set the password. 4. Click “Create Account”. 5. Type a password in “Type a new password”. 6.[...]

2.16 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures [User's Passport] appears in “Ent er your password”. Click [Next]. When the finger print has been enrolled, [U ser’s Password] appear s. Slide your finger enrolled or type the password. Click [Next] . 5. Type the Windows logon password in “Enter your password” and [...]

2 Troubleshooting Procedures 2.16 Fingerprint sensor Troubleshooting 6. Confirm that the box of [Run interactive tu torial] is checked (when proceeding wit seeing Tutorial) and click [Next]. 7. Watch the Video carefully, click [Next]. 2-62 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc e Manual (960- 633)[...]

2.16 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures 8. Put lightly your finger on the fingerprint sens or at the right side of the touchpad panel and slide your finger sideways Slide your finger four times. Four boxes ar e filled with fingerprints. At this time, when you click the [Replay video], you can watch the video that you h[...]

2 Troubleshooting Procedures 2.16 Fingerprint sensor Troubleshooting When you have failed in any time of four tim es reading and want to practice again, click [Try again]. When you have fully su cceeded in four times of reading, the message of “ Fully succeeded” appears. 9. Click [Next]. The displa y of [User’s Fingers] 10. Click the box you [...]

2.16 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures Put lightly the first joint of your finger you wa nt to enroll on the fi ngerprint sensor and slide your finger sideways. Enroll your finger three times. Every tim e your finger has been successfully enrolled, one box is checked. When your finger has been successfully enrolled th[...]

2 Troubleshooting Procedures 2.16 Fingerprint sensor Troubleshooting 13. Type a backup password two times in the fo llowing display. (This password is different from the password of Windows logon.) 14. Click [Next]. The [Finish] display appears. 15. Click [Finish], “Welcome” display appears. 2-66 [ CONFIDENTIAL] TECRA A9(S5/P5/S2 00) Maintenanc[...]

2.16 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures Procedure 3 Authentication of fingerprint 1. Turn on the computer to start up Windows. 2. In the Windows logon window, put lightly the first joint of your finger registered and slide your finger sideways. When authenticated, [Success] is displayed in the fingerprint authenticatio[...]

2 Troubleshooting Procedures 2.16 Fingerprint sensor Troubleshooting Procedure 4 Connector Check and Replacement Check The Fingerprint sensor cable is connected to the connector CN9650 on th e Fingerprint sensor board and connector CN9550 on the system board. Check 1 Check the Fingerprint sensor cable is firmly connected to the connector CN 9650 on[...]

[CONFIDENTIAL] Chapter 3 Tests and Diagnostics[...]

3 Tests and Diagnostics 3-ii [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Ma nual (960-633 ) 3[...]

3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3) [CONFIDENTIAL] 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ................................................................................. 3[...]

3 Tests and Diagnostics 3-iv [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Ma nual (960-633 ) 3.21 Head Cleaning .......................................................................................................... 3-4 8 3.21.1 Function Description .......................................................................... 3-48 3.21.2 Operati[...]

3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance M anual (960-63 3) [CONFIDENTIAL ] 3-v 3.30 BIOS SETUP ........................................................................................................... 3-86 3. 30.1 Function Description .......................................................................... 3-86 3. 30.2 Accessin[...]

3 Tests and Diagnostics 3-vi [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Ma nual (960-633 )[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disks. There are Service Pro[...]

3 Tests and Diagnostics 3.1 The Diagnostic Test 3-2 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)  NDP TEST  EXPANSION TEST  CD-ROM/DVD-ROM TEST  ERROR RETRY COUNT SET [FDD & HDD] Other tests are:  Wireless LAN TEST (Wireless LAN TEST disk)  LAN/Modem/Bluetooth/IEEE1394 TEST (LAN/Modem/Bluetooth/IEEE1394 TE[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-3 3.1.2 H/W (Hardware) initial information setting tool The H/W initial inform ation setting tool consists of the following programs.  Initial configuration  DMI information save  DMI information recovery  System configura[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3.2 Executing the Diagnostic Test To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the USB floppy disk drive. 2. Turn on the computer while pressing U key. The following menu appears. Repair test program 1 Repair Main 2 Repair Initial config set 3 Repair[...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2.1 Diagnostics menu (T&D) To execute this program, press 1 Repair Main and press Enter in the startup menu, press Enter . The following menu appears. TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC TEST 2 –[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST 3 - KEYBOARD TEST 4 - DISPLAY TEST 5 - FLOPPY DISK [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Select the option you want to execute and press Enter . When you select 1- SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT : XXXXX WRITE DATA : [...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-8 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Selecting YES of ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]] 1: Test end 2: Conti[...]

3.3 Setting of the hardware configuration 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-9 3.3 Setting of the hardware configuration To execute this program, 2, Repair Initial config set and press Enter in the startup m enu, press Enter and follow the directions on the screen. The H/W initial inform atio[...]

3 Tests and Diagnostics 3.3 Setting of the hardware configuration 3-10 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 7. “ Create DMIINFO TXT (Y/N) ? ” is displayed. Press Y , then the DMI information (text data) is written to the Floppy disk, etc. • Setting of the HWSC • Setting of the UUID • Display of the DMI informa[...]

3.4 Heatrun Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-11 3.4 Heatrun Test To execute this program, press 3 , Repair Heatrun and press Enter in the startup menu, press Enter . After selecting this test, the same subtests as 3.23 Running Test are executed successively. For more details on the pro[...]

3 Tests and Diagnostics 3.5 Subtest Names 3-12 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 3.5 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF Geyserville Quick[...]

3.5 Subtest Names 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-13 Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 6 PRINTER ［ It is not supported ］ 01 02 03 Ripple pattern Function Wraparound 7 ASYNC 01 02 03 FIR/SIR Point to point (send) FIR/SIR Point to point (receive) Wrapar[...]

3 Tests and Diagnostics 3.6 System Test 3-14 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 3.6 System Test To execute the System Test, select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 ROM checksum Th[...]

3.6 System Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-15 Subtest 04 Quick charge This subtest checks the status for the quick charge. Subtest 05 DMI read This subtest displays the information in the Flash-ROM in the following format. *** DMI Data Display Ver X.XX *** Model Name : XXXXXXXXXXX Ver[...]

3 Tests and Diagnostics 3.7 Memory Test 3-16 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 3.7 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Conventional me[...]

3.8 Keyboard Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-17 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed k[...]

3 Tests and Diagnostics 3.9 Display Test 3.9 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA This subtest writes the constant data (AAh and 55h) to the [...]

3.9 Display Test 3 Tests and Diagnostics Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [Mode 117 1024*768 64K] [Mode 118 1024*768 16M] The dis[...]

3 Tests and Diagnostics 3.9 Display Test 3-20 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Subtest 06 “H” pattern display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH[...]

3.10 Floppy Disk Test 3 Tests and Diagnostics 3.10 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD because the contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Ent[...]

3 Tests and Diagnostics 3.10 Floppy Disk Test 3-22 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : ke[...]

3.11 Printer Test 3 Tests and Diagnostics 3.11 Printer Test NOTE : Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : An IBM compatible printer must be connected to the system to execute this test. Also, printer port wraparoun[...]

3 Tests and Diagnostics 3.11 Printer Test Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wraparound NOTE : To execute thi[...]

3.12 Async Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-25 3.12 Async Test To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 and 02[...]

3 Tests and Diagnostics 3.13 Hard Disk Test 3-26 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 or[...]

3.13 Hard Disk Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-27 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest. HARD DISK TEST XXXXXX[...]

3 Tests and Diagnostics 3.13 Hard Disk Test 3-28 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder and then reads the data while moving from cylinder to cylinder. (Tests the data interference in the neighbor trac[...]

3.14 Real Timer Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-29 3 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01[...]

3 Tests and Diagnostics 3.14 Real Timer Test 3-30 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments, m aking sure the date and time are displayed in the following form at: Curren[...]

3.15 NDP Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-31 3.15 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 NDP This test checks the following functions of NDP:  Control word  Status word  Bus ?[...]

3 Tests and Diagnostics 3.16 Expansion Test 3-32 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wrap around [ It is not supported ] CAUTION : PCMCIA wraparound test is [...]

3.16 Expansion Test 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-33 Subtest 02 RGB monitor ID NOTE: To execute this subtest, an external monitor with monitor ID function is required. Connect the external monitor to the PC for the test of ID acquisition. The judgment of acquisition is based on the panel[...]

3 Tests and Diagnostics 3.17 CD-ROM/DVD-ROM Test 3-34 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.17 CD-ROM/DVD-ROM Test NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01 or ABEX TEST CD-ROM TCDR-702 and DVD-ROM TEST DISK TSD-1. For the subtest 04, use a CD-RW on the market. Subtest 01 Sequential r[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-35 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the DIAGNOSTIC TEST. Table 3-2 Error codes and error status names (1/3) Device name Error code Error status name (Comm[...]

3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3-36 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD - R[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-37 Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DMA[...]

3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status 3-38 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an e[...]

3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-39 Table 3-4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used. “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1”[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-40 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.20 ONLY ONE TEST 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. ##################[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 1 Pressed key display When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function that causes the key’s di[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-42 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Subtest 2 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check. This test displays the response from the touch pad and touch pad switch. When moving your fing[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-43[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-44 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Subtest 3 Wireless comm unication switch This subtest checks if the Wireless comm unication switch works properly. If the test is started with the switch ON, following message appears in the display. Wireless communication switch is set [...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 5 LED This subtest checks if each LED lights properly. The following m essage appears in the display in order. Follow the instructions in the display to execute the test. [HDD Access LED test] Press any key and following message appears in the display. [Caps/Num/Overlay BT/W-LAN LED test] (1) Press[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST Press the Toshiba Presentation button after the following message appears. Step2 X 1 2 * * * . Press Function button (Presentation button) OK m essage appears in the display if the test ends without an error. Press any key return to each Steps if NG! or Press any key message apprears. If the test ends succ[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics Top (heaven surface) TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-47 Right side Left side Back Front When this subtest is selected, the following message appears in the display. The heaven surface establishes in the upper direction Press [Enter] key NOTE : Be sure to execute the test[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-48 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) When there is no defective during the all checks above, the following message appears in the display. Then press Enter and return to the Only One Test menu. ** Setting OK! ** Press [Enter] key When any trouble in the above setting is fou[...]

3.21 Head Cleaning 3 Tests and Diagnostics TECRA A8 /Satellite Pro A120 Maintenance Manual (960-573) [CONFIDENTIAL] 3-49 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operations 1. Selec[...]

3 Tests and Diagnostics 3.22 Log Utilities 3-50 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk, or output the data to a printer or th[...]

3.22 Log Utilities 3 Tests and Diagnostics 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, the error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED 001 FDD 01 0000 180 00001 00 00 0000 FDD-TIME OUT ER[...]

3 Tests and Diagnostics 3.23 Running Test 3-52 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02) 3. Display test (subtest 01) 4. Real timer test (subtest 02) [...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-53 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a fl[...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-54 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message. [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-55 3. COPY program (a) When COPY is selected, the following message appears. FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a m essage similar to the one[...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-56 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 4. DUMP program (a) When DUMP is selected, the following message appears. DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display wi[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-57 (k) The following message will appear. To finish the dum p, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No) [...]

3 Tests and Diagnostics 3.25 System Configuration 3-58 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-631) 3 3.25 System Configuration 3.25.1 Function Description NOTE : To display the system configuration, the write protect tab should be OFF position. If the tab is ON position, move the tab to OFF position and restart the test. Other[...]

3.23 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-59 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter . Then, the following system configuration appears in the display. System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX-XXXXXMHz Code = XX L2 Cache [...]

3 Tests and Diagnostics 3.26Wireless LAN Test Program (Intel -made b/g, a/b/g Setting up of REF PC) 3.26 Wireless LAN Test Program (Intel-made b/g, a/b/g Setting up of REF PC) For the test of Intel-made wireless LAN cards , configure the test environm ent as shown below with the following equipment. ・ AP （ which can operate on Windows XP a nd i[...]

3.26 Wireless LAN Test Program (Intel -made b/g, a/b/g Setting up of REF PC) 3 Tests and Diagnostics 2. Open “My Computer” window and click “My Network places” on the left column. 3. Click “View network connections” on the left column. 4. The “Network Connections” window appears. Double-click “Local Area Connection”. Network Con[...]

3 Tests and Diagnostics 3.26Wireless LAN Test Program (Intel -made b/g, a/b/g Setting up of REF PC) 5. Click “Install…” button on the “Local Area Connection Properties” window. Local Area Connection Properties window 6. Select “Protocol” on the “Select Network Component Type” window and click “Add…” button. Select Network Co[...]

3.26 Wireless LAN Test Program (Intel -made b/g, a/b/g Setting up of REF PC) 3 Tests and Diagnostics 8. When “Install From Disk” window appears, click “Browse…” and specify the created “Clx_Res” folder. Then Click “OK”. (For the test, “PACKET.INF” file is used.) Install From Disk window 9. The “Select Network Protocol” win[...]

3 Tests and Diagnostics 3.26Wireless LAN Test Program (Intel -made b/g, a/b/g Setting up of REF PC) After the completion of REF PC setup, restart the WINDOW S. Then perform the Responder test program for Windows (W TWINSVR.EXE) in the Clx_Res folder. ・ WTWINSVR.EXE Function : Transmitting/receiving of data to/from DUT via AP OS available : Window[...]

3.27 Wireless LAN Test Program on DUT PC( Intel-made) 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-65 3.27 Wireless LAN Test Program on DUT PC(Intel-made) 3.27.1 Wireless LAN Test Program (Intel-made :Golan) on DUT PC This section describes how to perform the wireless LAN transm itting-receiving test ([...]

3 Tests and Diagnostics 3.27Wireless LAN Test Program on DUT PC( Intel-made) 3-66 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-631) Press any key and return to the test m enu. If a defective is found during the test, NG message will appear in the display. Press any key and return to the test m enu. W hen a defective is detected in t[...]

3.27 Wireless LAN Test Program on DUT PC( Intel-made) 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-67 Subtest03 Antenna check & communication test of 11b m ode This subtest execute transmitting/receiving test in 802.11b mode using the main antenna first. If a defective is not found during the test,[...]

3 Tests and Diagnostics 3.27Wireless LAN Test Program on DUT PC( Intel-made) 3-68 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-631) Subtest05 Communication test of 11g m ode This subtest execute transmitting/receiving test in 802.11g mode using the main antenna. If a defective is not found during the test, OK message will appear in [...]

3.27 Wireless LAN Test Program on DUT PC( Intel-made) 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-69 3.27.2 Wireless LAN T est Program (Intel-made:Kedron) on DUT PC This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made 802.11 a/b/g or 802.11 a/b/g/n: kedron).[...]

3 Tests and Diagnostics 3.27Wireless LAN Test Program on DUT PC( Intel-made) 3-70 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-631) Press any key and return to the test m enu. W hen a defective is detected in the test, following typical cause is considered. • • • • • • Connection of wireless LAN card Using a wrong wirele[...]

3.27 Wireless LAN Test Program on DUT PC( Intel-made) 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-71 This subtest execute transmitting/receiving test in 802.11a mode using the main antenna. If a defective is not found during the test, OK message will appear in the display. Press any key and return to [...]

3 Tests and Diagnostics 3.27Wireless LAN Test Program on DUT PC( Intel-made) 3-72 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-631) Subtest05 Communication test of 11g m ode This subtest execute transmitting/receiving test in 802.11g mode using the main antenna. If a defective is not found during the test, OK message will appear in [...]

3.28 LAN/Modem/Bluetooth/ IEEE1394 Test Program 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-73 3.28 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Mode m/Bluetooth/IEEE139[...]

3 Tests and Diagnostics 3.28LAN/Modem/Bluetoot h/IEEE1394 Test Program Subtest01 (i82562 + ICHx) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear: [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error count = 00000 LOOPBACK TEST 100Mbps Auto-negotiation TxRx Tes[...]

3.28 LAN/Modem/Bluetooth/ IEEE1394 Test Program 3 Tests and Diagnostics Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear: Testing adaptor...hit <ESC> to abort. * External Loopback Test...PASSED Testing completed. * * Loop[...]

3 Tests and Diagnostics 3.28LAN/Modem/Bluetoot h/IEEE1394 Test Program 3-76 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-631) 3.28.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Denki Seisakusyo)” for the[...]

3.28 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3.28.3 Bluetooth test Preparation ・ For the test of Bluetooth function, use the Windows program installed on the target computer (computer to be tested). A responder device (device for transm itting/receiving data) is also needed. (A mobile phone with the Bluetooth function is[...]

3 Tests and Diagnostics 3.28 LAN/Modem/Bluetooth/IEEE1394 Test Program 5. Select “Diagnostics” tab and click “Run”. 6. Check the “Log” to confirm the test result. BT address of test computer BT address of responder device 7. When the BT (Bluetooth) address of the responder device appears, the Bluetooth card and antenna connection are OK[...]

3.28 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-79 3.28.4 IEEE1394 test To execute this test, press 4 and Enter . NOTE: IEEE1394 test is not supported for this model. NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference m[...]

3 Tests and Diagnostics 3.29 Sound Test program 3-80 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) 3.29 Sound Test program This section describes how to perform the Sound test. To execute the sound test, refer to the following description. Prepare a HDD and format it on DOS. Copy all files in the floppy disk in which the Sound t[...]

3.29 Sound Test program 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-81 To return to the Sound test menu, press 9 and Enter . Then following message will appear in the display. *********************************** ******** May I Restart ? ******* *********************************** Press any key to cont[...]

3 Tests and Diagnostics 3.29 Sound Test program 3-82 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Subtest 02 Sine wave This subtest is executed by loading the COM file (ADSIN.COM). The program expands sine wave data table from 16KB to 64KB, and creates the play data. Then it transfers the data between the DMA and the CODEC to pl[...]

3.29 Sound Test program 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-83 3.29.3 CD Sound (Standard) test To execute the CD Sound (Standard) test, press 3 and Enter . Insert the test media (TOSHIBA TEST CD-ROM or ABEX TEST CD-ROM) or music CD on the market (if the test media can not be prepared). Followi[...]

3 Tests and Diagnostics 3.29 Sound Test program 3-84 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Subtest 02 English Narration Selected this subtest, narration in English starts. For m ore details on the procedure, refer to the subtest01. Subtest 03 Test Tone A CAUTION: Before starting subtest03, be sure to set the sound at prop[...]

3.29 Sound Test program 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-85 3.29.3.2 Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ; test end [Ctrl]+[C] ; key stop SUB-TEST : XX PASS COUNT : XXXXX ERR[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-86 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 3.30 BIOS SETUP 3.30.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory (a) Total 2. System Date/Time (a) Date (MM-DD-YYYY) (b) Time (HH:MM:SS) 4. Password (a) User Password (b) Sup[...]

3.30 BIOS SETUP 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-87 8. Configuration (a) Device Config. 9. Battery (a) Battery Save Mode (b) PCI Express Link ASPM (c) Enhanced C-States 10. I/O ports (a) Serial 11. Drives I/O (a) Built-in HDD (b) Select Bay 12. PCI Bus (a) PCI Bus 13. Display (a) Power On D[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3.30.2 Accessing the BIOS SETUP Program Turn on the power while pressing ESC, the following menu appears. Check system. Then press [F1] key. Then press F1 . The following display appears. 3-88 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[...]

3.30 BIOS SETUP 3 Tests and Diagnostics Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to m ove between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between the two pages. 2. Press either the Space bar or Back Space to change the value. Accepting Chang[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-90 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Are you sure? (Y/N) The changes you made will cause the system to reboot. 2. To make other changes, press N . Repeat the steps above. 3. To accept the changes, press Y . NOTE: You can press Esc to quit at any time without saving changes. SE[...]

3.30 BIOS SETUP 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-91 SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. (a) Total This field displays the total amoun[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-92 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 4. HDD Password This option sets HDD password. HDD password is a security function to protect the built-in HDD. (a) HDD This item selects the hard disk to set HDD password. Built-in HDD Sets HDD password for the built-in HDD (b) HDD Passwor[...]

3.30 BIOS SETUP 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-93 5. Boot Priority This tab sets the priority for booting the computer and the priority for the built-in HDD or optional secondary HDD. (a) Boot Priority HDD → FDD → CD-ROM → LAN: The computer looks for bootable files in the following [...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-94 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 7. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) Core-Multi Processing NOTE: This is not displayed in PCs with a single core CPU. The Core M[...]

3.30 BIOS SETUP 3 Tests and Diagnostics Virtualization Technology (e) Auto Power On Use this option to set a time and date for automatic power on and enable or disable the ring indicator feature. Alarm Date Option appears only when Alarm Time is enabled. Set the parameters for the Auto Power On (automatic power on) function and the Wake-up on LAN i[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-96 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Critical Battery Wake-up Configures what action is taken when the remaining battery power is close to running out while the system is in Sleep Mode. This setting is only available when the Critical battery action within Power Options in Win[...]

3.30 BIOS SETUP 3 Tests and Diagnostics 8. Configuration This option displays the configuration method. (a) Device Config. The devices are initialized when the PNP OS loads. Setup by OS Initializes devices, which is needed to load an operating system. Operating system initializes other devices. (Default) All Devices All devices will be initialized.[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-98 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) NOTE: The brightness is when a AC adaptor is connected. When powered by a battery it is displayed as follows. Battery Save Mode = Full power : LCD Bright ness = Bright. Battery Save Mode = Low power: LCD Bright ness = Semi-Bright. (a) Batte[...]

3.30 BIOS SETUP 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-99 Battery optimized If the CPU becomes too hot, the processing speed is lowered. If the temperature is still too high, the fan turns on. When the CPU temperature falls to a normal range, the fan is turned off and the processing speed is incr[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-100 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 10. .I/O ports This option controls settings for the parallel port. NOTE: Do not assign the same interrupt request level and I/O address to the serial port and PC card. (a) Serial Use this option to set the COM level for the serial port. T[...]

3.30 BIOS SETUP 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-101 (c) SATA Controller Mode This feature sets the SATA Controller Mode. AHCI Sets AHCI which is the mode for VistaTM (default) Compatibility Sets the mode for legacy OS. Use this mode when the driver corresponding to AHCI is not used. 12. PC[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-102 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) 15. Legacy Em ulation. (a) USB KB/Mouse Legacy Emulation. Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/M[...]

3.30 BIOS SETUP 3 Tests and Diagnostics TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) [CONFIDENTIAL] 3-103 17. Security controller (a) TPM Disables the security controller called TPM (Trusted Platform Module). When the cursor is on the Enable ( Disable ) and the Space is pressed, message is displayed and the PC waits Y or N key input by the us[...]

3 Tests and Diagnostics 3.30 BIOS SETUP 3-104 [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[...]

Chapter 4 Replacement Procedures [CONFIDENTIAL][...]

4 Replacement Procedures 4-ii [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-iii Chapter 4 Contents 4.1 General .................................................................................................................... ... 4-1 4.2 Battery pack .......................................................[...]

4 Replacement Procedures 4-iv [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) 4.30.1 Replacing the 15.4-inch WXGA Samsung Fluorescent Lamp........... 4-96 4.30.2 Replacing the 15.4-inch WSXGA+ Samsung Fluorescent Lamp .... 4-100 Figures Figure 4-1 Removing the battery pack .................................[...]

4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-v Figure 4-28 Removing the microphone ........................................................................... 4-47 Figure 4-29 Removing the RGB board (1) ...................................................................... 4-4[...]

4 Replacement Procedures 4-vi [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.1 Overview 4 Replacement Procedures 4 Replaceme nt Procedure s 4.1 Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be removed before a particula[...]

4 Replacement Procedures 4.1 Overview 4-2 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Ma intenance Manual (960-633) Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions while working on the computer. DANGER: 1) Always use the genuine battery that is au[...]

4.1 Overview 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-3 Before You Begin Take note of the following points before starti ng work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for rem oving the battery pack is describe[...]

4 Replacement Procedures 4.1 Overview Disassembly Procedure Four main types of cable connector are used. Pressure plate connector • • • • Spring connector Back flip connector Normal pin connector For pressure plate connectors, slide the pressure plate holding tags on both sides of the plastic pressure plate on the connector and pull the cab[...]

4.1 Overview 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-5 Assembly Procedures After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembli[...]

4 Replacement Procedures 4.1 Overview Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE: Toshiba recommends that you use an electric screw driver fo[...]

4.1 Overview 4 Replacement Procedures Grip Color Some screws have a colored grip area to help you determine the length of the screw.  Even numbered length screws: Brown  Odd numbered length screws: Wh ite  Special length screw: Blue “Special length screw” means screws whose length is indicated in an integral number to the first decimal[...]

4 Replacement Procedures 4.2 Battery pack 4.2 Battery pack Removing the Battery pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack. 1. Turn off the p[...]

4.2 Battery pack 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-9 Installing the Battery pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handle[...]

4 Replacement Procedures 4.3 PC card 4.3 PC card Removing the PC card To remove the PC card, follow the steps below and refer to Figure 4-2. CAUTION: Before you remove the PC card, refer to the card’s documentation and to your operating system documentation for proper procedures and precautions. 1. Press the eject button for the PC card to extend[...]

4.4 Bridge media 4 Replacement Procedures 4.4 Bridge media Removing the Bridge media To remove the Bridge media, follow the steps below and refer to Figure 4-3. CAUTION: Before you remove the Bridge media, refer to the media’s documentation and to your operating system documentation for proper procedures and precautions. 1. Push the Bridge media [...]

4 Replacement Procedures 4.5 HDD 4.5 HDD CAUTION : When handling the HDD, do not press the top and bottom surface as shown by the arrow. Hold it by the sides. Removing the HDD To remove the HDD, follow the steps below and refer to Figure 4-4 to 4-6. 1. Turn the computer upside down. 2. Remove the following screws securing the HDD cover. 3. Insert y[...]

4.5 HDD 4 Replacement Procedures 4. Remove the HDD assembly from the connector of the HDD cable . Be careful not to damage the connector. HDD assembly HDD cable Figure 4-5 Removing the HDD assembly TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-13[...]

4 Replacement Procedures 4.5 HDD NOTE: The following steps describe how to disassemble the HDD assembly, however, do not disassemble if the HDD is working properly. 5. Place the HDD assembly on a flat surface, and remove the following screw s . • M3 × 4C FLAT HEAD screw × 4 6. Separate the HDD and HDD Holder . CAUTION: Do not apply pressure to [...]

4.5 HDD 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-15 Installing the HDD To install the HDD, follow the steps below and refer to Figure 4-4 to 4-6. CAUTION: Do not hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Install the HDD to the HDD Holder a[...]

4 Replacement Procedures 4.6 MDC/Memory module 4.6 MDC/Memory module Removing the MDC/Memory module To remove the MDC/mem ory module, follow the steps below and refer to Figure 4-7 and 4-8. 1. Loosen the screw and remove the memory module cover . 2. Open the left and right latches outside and remove the memory module(s) . CAUTION: When removing the[...]

4.6 MDC/Memory module 4 Replacement Procedures 3. Remove the following screws securing the MDC. • M2 × 4B BIND screw × 2 4. Lift the MDC straight above and remove it from the CN3010 on the system board. 5. Disconnect the MDC cable from the connector on the MDC. MDC CN3010 MDC cable M2 × 4B BIND Figure 4-8 Removing the MDC TECRA A9/TECRA S5/TEC[...]

4 Replacement Procedures 4.6 MDC/Memory module 4-18 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the MDC/Memory module To install the MDC/memory m odule, follow the steps below and refer to Figure 4-7 and 4-8. NOTE: When the power of the computer is turned on, the computer checks automaticall[...]

4.7 Keyboard 4 Replacement Procedures 4.7 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figure 4-9 to 4-11. 1. Turn over the computer. 2. Open the display and make it flat. 3. Insert your fingers into the slots on both sides and remove the keyboard holder . Keyboard holder Slot Slot Display Figure 4-9 Re[...]

4 Replacement Procedures 4.7 Keyboard 4. Remove the following screws securing the keyboard. • M2.5 × 4B FLAT HEAD screw × 2 5. Lift the top edge of the keyboard while releasing the hook and turn the keyboard face down on the palm rest. M2.5 × 4B FLAT HEAD M2.5 × 4B FLAT HEAD Hook Keyboard Figure 4-10 Removing the keyboard (1) 4-20 [CONFIDENTI[...]

4.7 Keyboard 4 Replacement Procedures 6. Remove the following screw and keyboard support plate . • M2.5 × 6B FLAT HEAD screw × 1 7. Disconnect the keyboard cable from the connector CN3230 on the system board and remove the keyboard . M2.5 × 6B FLAT HEAD Keyboard support plate Keyboard Keyboard cable CN3230 Figure 4-11 Removing the keyboard (2)[...]

4 Replacement Procedures 4.7 Keyboard 4-22 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the Keyboard To install the keyboard, follow the steps below and refer to Figure 4-9 to 4-11. 1. Place the keyboard face down on the palm rest. 2. Connect the keyboard cable to the connector CN3230 on the [...]

4.8 Bluetooth module 4 Replacement Procedures 4.8 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow the steps below and refer to Figure 4-12. 1. Disconnect the Bluetooth antenna cable from the Bluetooth module using an antenna coaxial cable disconnector. 2. Push the hook in the direction in the following figure a[...]

4 Replacement Procedures 4.8 Bluetooth module 4-24 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the Bluetooth module To install the Bluetooth module, follow the steps below and refer to Figure 4-12. 1. Connect the Bluetooth cable to the connector CN4400 on the system board. 2. Stick a new ins[...]

4.9 SW membrane 4 Replacement Procedures 4.9 SW membrane Removing the SW membrane To remove the SW m embrane, follow the steps below and refer to Figure 4-13 and 4-14. 1. Lift the switch cover up while pushing the portion shown in the figure below. Switch cover Figure 4-13 Removing the switch cover TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main[...]

4 Replacement Procedures 4.9 SW membrane 2. Disconnect the SW membrane cable from the connector CN9550 on the system board. 3. Push down the hook and slide the SW membrane in the direction in the figure below. 4. Remove the SW membrane . SW membrane Hook SW membrane cable CN9550 Figure 4-14 Removing the SW membrane Installing the SW membrane To ins[...]

4.10 Fan hood 4 Replacement Procedures 4.10 Fan hood NOTE : When repairing the PC, clean the fan hood and cooling fin with a vacuum cleaner and cotton sticks, and remove dusts with tweezers. Removing the Fan hood To remove the fan hood, follow the steps below and refer to Figure 4-15. 1. Peel off the insulator that prevents a waterdrop from enterin[...]

4 Replacement Procedures 4.10 Fan hood 4-28 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the Fan hood To install the fan hood, follow the steps below and refer to Figure 4-15. 1. Install the fan hood into the slot. 2. Stick a new insulator that prevents a waterdrop from entering the computer.[...]

4.11 Wireless LAN card 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-29 4.11 Wireless LAN card Removing the Wireless LAN card To remove the wireless LAN card, follow the steps below and refer to Figure 4-16 to 4-18. CAUTION: Do not try to remove the wireless LAN card with the c[...]

4 Replacement Procedures 4.11 Wireless LAN card Wireless LAN antenna cable (white, black and gray) M2x4B BIND Wireless LAN card Insulator (Three antenna cables) M2x4B BIND Wireless LAN card Insulator Wireless LAN antenna cable (white and black) (Two antenna cables) Figure 4-16 Removing the wireless LAN card 4-30 [CONFIDENTIAL] TECRA A9/TECRA S5/TEC[...]

4.11 Wireless LAN card 4 Replacement Procedures 5. Peel off the insulator that prevents a waterdrop from entering the computer. Insulator Figure 4-17 Removing the insulator 6. Pull out the wireless LAN antenna cables from the hole of the cover assem bly. 7. Pass the Bluetooth antenna cable and wireless LAN antenna cables from the hole of the cover [...]

4 Replacement Procedures 4.11 Wireless LAN card 4-32 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the Wireless LAN card To install the wireless LAN card, follow the steps below and refer to Figure 4-16 to 4-18. CAUTION: Be sure to switch the computer off before installing the wireless LAN car[...]

4.12 Optical drive 4 Replacement Procedures 4.12 Optical drive Removing the Optical drive To remove the optical drive, follow the steps below and refer to Figure 4-19 and 4-20. CAUTION: After removing the optical drive, do not put fingers inside the slot. It may cause injury. 1. Close the display and turn over the computer. 2. Remove the following [...]

4 Replacement Procedures 4.12 Optical drive 5. Remove the following screws and pushing plate . • M2 × 2.7C S-THIN HEAD screw × 2 6. Remove the following screw and mounting plate . • M2 × 3C S-THIN HEAD screw × 1 M2 × 3C S-THIN HEAD Mounting plate M2 × 2.7C S-THIN HEAD Pushing plate Figure 4-20 Disassembling the optical drive 4-34 [CONFIDE[...]

4.12 Optical drive 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-35 Installing the Optical drive To install the optical drive, follow the steps below and refer to Figure 4-19 and 4-20. 1. Set the mounting plate and secure it with the following screw . • M2 × 3C S-THIN HEAD s[...]

4 Replacement Procedures 4.13 Cover assembly and Base assembly 4 Replacement Procedu es 4.13 Cover assembly and Base assembly r Removing the Cover assembly and Base assembly To remove the cover assembly and base assem bly, follow the steps below and refer to Figure 4-21 and 4-22. 1. Close the display and turn over the computer. 2. Remove the follow[...]

4.13 Cover assembly and Base assembly 4 Replacement Procedures 4. Turn over the computer and open the display. 5. Disconnect the LCD cable, speaker cable , fingerprint sensor cable and touch pad cable from the connector CN5000 , CN6170 , CN 9550 and CN3240 on the system board. 6. Remove the following screws . • M2.5 × 6B FLAT HEAD screw × 3 7. [...]

4 Replacement Procedures 4.13 Cover assembly and Base assembly 4-38 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the Cover assembly and Base assembly To install the cover assembly and base assembly, follow the steps below and refer to Figure 4-21 to 4-22. 1. Place the cover assembly on the ba[...]

4.14 Touch pad 4 Replacement Procedures 4.14 Touch pad Removing the Touch pad To remove the touch pad, follow the steps below and refer to Figure 4-23 and 4-24. 1. Lift the tip portions up first and remove the touch pad cover while releasing latches. 2. Remove the following screw and touch pad assembly from the slot. • M2.5 × 10B FLAT HEAD screw[...]

4 Replacement Procedures 4.14 Touch pad 3. Turn over the touch pad assembly and peel off the glass tape and disconnect the touch pad cable from the connector on the touch pad assembly. Touch pad assembly Touch pad cable Glass tape Connector Figure 4-24 Removing the touch pad (2) 4-40 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main[...]

4.14 Touch pad 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-41 Installing the Touch pad To install the touch pad, follow the steps below and refer to Figure 4-23 and 4-24. 1. Connect the touch pad cable to the connector on the touch pad and stick the glass tape in place. 2. Tu[...]

4 Replacement Procedures 4.15 Fingerprint sensor board 4.15 Fingerprint sensor board Removing the Fingerprint sensor board To remove the fingerprint sensor board, follo w the steps below and refer to Figure 4-25 and 4-26. 1. Push the hook down and remove the fingerprint sensor board hold plate while sliding it from the guides in the direction of th[...]

4.15 Fingerprint sensor board 4 Replacement Procedures 3. Remove the fingerprint sensor board fixed with the double-sided tape and peel off the double-sided tape that prevents a waterdrop from entering the computer. 4. Disconnect the fingerprint sensor cable from the connector on the fingerprint sensor board. Fingerprint sensor board Fingerprint se[...]

4 Replacement Procedures 4.15 Fingerprint sensor board Installing the Fingerprint sensor board To install the fingerprint sensor board, follow the steps below and refer to Figure 4-25 and 4- 26. NOTE : When installing a new fingerprint sensor board, make sure that the insulators and gasket are placed as shown in the following figure. 1. Connect the[...]

4.16 RTC battery 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-45 4.16 RTC battery WARNING: When replacing the RTC battery, be sure to use a genuine battery authorized by Toshiba. Installing the wrong battery could cause a battery explosion or other damage. If the RTC battery i[...]

4 Replacement Procedures 4.16 RTC battery Removing the RTC battery To remove the RTC battery, follow the steps below and refer to Figure 4-27. 1. Peel off the glass tape . 2. Disconnect the RTC battery cable from the connector CN9300 on the system board and remove the RTC battery . RTC battery CN9300 Glass tape RTC battery cable Figure 4-27 Removin[...]

4.17 Microphone 4 Replacement Procedures 4.17 Microphone Removing the Microphone To remove the microphone, follow the steps below and refer to Figure 4-28. 1. Peel off the glass tape . 2. Disconnect the microphone cable from the connector CN6050 on the system board and remove the microphone from the slot of the base assem bly. Microphone Microphone[...]

4 Replacement Procedures 4.18 RGB board 4.18 RGB board Removing the RGB board To remove the RGB board, follow the steps below and refer to Figure 4-29 and 4-30. 1. Peel the insulator and take out the LAN jack from the slot. (Be careful, because the LAN jack cable is still connected to the connector on the back of the system board.) LAN jack Insulat[...]

4.18 RGB board 4 Replacement Procedures 2. Remove the cushion from the slot. 3. Disconnect the RGB board cable from the connector on the RGB board. (Be careful, because the RGB board cable is still connected to the connector on the back of the system board.) 4. Remove the RGB board while pushing the base assembly in the direction of the arrow in th[...]

4 Replacement Procedures 4.18 RGB board Installing the RGB board To install the RGB board, follow the steps below and refer to Figure 4-29 and 4-30. NOTE : When installing a new RGB board, make sure that the insulator and gaskets are placed as shown in the following figure. 1. Connect the RGB board cable to the connector on the RGB board. 2. Instal[...]

4.19 System board 4 Replacement Procedures 4.19 System board Removing the System board To remove the system board, follow the steps below and refer to Figure 4-31 to 4-33. 1. Remove the cable holder while pushing four hooks up. Cable holder Hook Hook Figure 4-31 Removing the cable holder TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Ma[...]

4 Replacement Procedures 4.19 System board 2. Disconnect the DC-IN jack from the connector CN8800 on the system board. 3. Peel off the glass tape and take out the HDD cable from the slot. (Be careful, because the HDD cable is still connected to the connector on the back of the system board.) 4. Remove the system board while releasing two latches . [...]

4.19 System board 4 Replacement Procedures CAUTION: When removing/installing the system board, handle the “Can be handled” areas and do not handle the “Can not be handled” area as shown in the figure below. Can not be handled Can be handled TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-53[...]

4 Replacement Procedures 4.19 System board 5. Peel the insulator and remove the modem jack and USB board from the slots. Modem jack USB board Insulator USB board cable Modem jack cable Figure 4-33 Removing the modem jack/USB board 4-54 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.19 System board 4 Replacement Procedures Installing the System board To install the system board, follow the steps below and refer to Figure 4-31 to 4-33. NOTE : When installing a new system board (front), make sure that the insulators, screws and CPU back plate assemblies are placed as shown in the following figure. (Front of the system board) T[...]

4 Replacement Procedures 4.19 System board NOTE : When installing a new system board (back), make sure that the insulators, gasket, screws and studs are placed as shown in the following figure. (Back of the system board) 4-56 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.19 System board 4 Replacement Procedures 1. Install the modem jack and USB board into the slot. 2. Arrange the modem jack cable and USB board cable to the guides and stick the insulator in place. 3. Install the system board while engaging two latches . CAUTION: When installing the system board, make sure that the wireless communication switch is [...]

4 Replacement Procedures 4.20 Battery lock/Battery latch 4.20 Battery lock/Battery latch Removing the Battery lock/Battery latch To remove the battery lock/battery latch, follow the steps below and refer to Figure 4-34. 1. Remove the battery lock cap while pushing latches inside to release them. 2. Remove the battery lock from the slot. Be careful [...]

4.20 Battery lock/Battery latch 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-59 Installing the Battery lock/Battery latch To install the battery lock/battery latch, follow the steps below and refer to Figure 4-34. 1. Insert the stick of battery lock into the spring . 2. Instal[...]

4 Replacement Procedures 4.21 HDD cable/LAN jack/RGB board cable 4.21 HDD cable/LAN jack/RGB board cable Removing the HDD cable/LAN jack/RGB board cable To remove the HDD cable/LAN jack/RGB board cable, follow the steps below and refer to Figure 4-35. 1. Turn over the system board. 2. Peel off the insulator and disconnect the HDD cable from the con[...]

4.21 HDD cable/LAN jack/RGB board cable 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-61 Installing the HDD cable/LAN jack/RGB board cable To install the HDD cable/LAN jack/RGB board cable, follow the steps below and refer to Figure 4-35. 1. Connect the LAN jack and RGB board c[...]

4 Replacement Procedures 4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU Removing the North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU To remove the North bridge (and GPU) heat sink/CPU heat sink/fan/CPU, follow the steps below and refer to Figure 4-36 to 4-40. 1. Remove [...]

4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 4 Replacement Procedures 3. Remove the following screws in the reverse order of the num bers marked on the North bridge holder and remove the North bridge hold plate . (In the case of the Built-in GPU model.) • M2 × 4B BIND screw × 3 4. Remove the North bridge heat sink . M2 × 4B BIND[...]

4 Replacement Procedures 4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 5. Remove the following screws in the reverse order of the num bers marked on the CPU hold plate. • M2 × 4B BIND screw × 3 6. Remove the CPU hold plate . 7. Peel off the acetate tape and disconnect the fan cable from the connector CN8771 on the system board. 8.[...]

4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 4 Replacement Procedures 9. Remove the fan hood . 10. Remove the following screws and separate the CPU heat sink and fan . • M2.5 × 4B FLAT HEAD screw × 2 Fan M2.5×4B FLAT HEAD M2.5×4B FLAT HEAD CPU heat sink Fan hood Figure 4-39 Removing the fan TECRA A9/TECRA S5/TECRA P5/Satellite [...]

4 Replacement Procedures 4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 11. Unlock the CPU by turning the cam counterclockwise on the CPU socket by 180 degrees with a flat-blade screwdriver. Figure 4-40 Removing the CPU 12. Remove the CPU . CAUTION: When removing the CPU, lift it up right above. Otherwise, pins of the CPU may be damage[...]

4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 4 Replacement Procedures Installing the North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU To install the North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU, follow the steps below and refer to Figure 4-36 to 4-42. 1. Make sure that the cam of the CPU socket is in the unlock (OPEN)[...]

4 Replacement Procedures 4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 4. Apply new grease on the CPU and North bridge using a special syringe as shown in the following figure. Apply quarter of scale (0.25ml) of grease evenly on the CPU chip and North bridge chip. When silicon grease is already applied to the CPU, wipe them off with a[...]

4.22 North bridge (and GPU) heat sink/CPU heat sink/Fan/CPU 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-69 12. Install the North bridge and GPU heat sink in place. (In the case of the GPU model.) 13. Install the North bridge and GPU hold plate on the North bridge and GPU heat[...]

4 Replacement Procedures 4.23 PC card slot 4.23 PC card slot Removing the PC card slot To remove the PC card slot, follow the steps below and refer to Figure 4-43. 1. Remove the following screws securing the PC card slot. • M2 × 3C S-THIN HEAD screw × 2 • M2 × 8C S-THIN HEAD screw × 2 2. Remove the PC card slot while pulling out the latch t[...]

4.24 LCD unit/FL inverter 4 Replacement Procedures 4 Replaceme nt Procedure s 4.24 LCD unit/FL inverter Removing the LCD unit/FL inverter To remove the LCD unit/FL inverter, follow the steps below and refer to Figure 4-44 to 4-46. 1. Open the display and make it flat. 2. Remove the mask seals and following screws securing the LCD m ask. • M2.5 ×[...]

4 Replacement Procedures 4.24 LCD unit/FL inverter 5. Peel off two glass tapes on the FL inverter. 6. Disconnect the cables from the both sides of FL inverter and remove the FL inverter . FL inverter Glass tape Cable Figure 4-45 Removing the FL inverter 4-72 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.24 LCD unit/FL inverter 4 Replacement Procedures 7. Remove two glass tapes securing the LCD cable and disconnect the LCD cable from the connector on the LCD unit. CAUTION : When removing the LCD cable, be careful not to damage the connector. 8. Remove the following screws and LCD unit . • M2 × 3C BIND screw × 4 CAUTION: When lifting up the to[...]

4 Replacement Procedures 4.24 LCD unit/FL inverter 4-74 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the LCD unit/FL inverter To install the LCD unit/FL inverter, follow the steps below and refer to Figure 4-43 to 4-45. 1. Install the LCD unit to the display cover and secure it with the follo[...]

4.25 Cover latch 4 Replacement Procedures 4.25 Cover latch Removing the Cover latch To remove the cover latch, follow the steps below and refer to Figure 4-47. 1. Remove the latch knob while pushing three hooks. 2. Remove the latch hook . CAUTION : Be careful not lose the spring . Latch knob Latch hook Spring Hook Hook Figure 4-47 Removing the cove[...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna 4.26 Wireless LAN antenna/Bluetooth antenna Removing the Wireless LAN antenna/Bluetooth antenna To remove the wireless LAN antenna/Bluetooth antenna, follow the steps below and refer to Figure 4-48. 1. Peel the insulator and peel off the acetate tapes securing the wireless LAN ant[...]

4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures Installing the Wireless LAN antenna/Bluetooth antenna To install the wireless LAN antenna/Bluetooth antenna, follow the steps below and refer to Figure 4-48. 1. Install the wireless LAN antennas (two or three) and Bluetooth antenna to the display cover. 2. Arrange the wireless LAN[...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna CAUTION: (Center right) Arrange the wireless LAN antenna cable (black) and Bluetooth antenna cable (brown) , and stick three acetate tapes in place. Wireless LAN antenna cable (black) Bluetooth antenna cable (brown) A cetate tape 1. Arrange the Bluetooth antenna cable (brown). 2. [...]

4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures CAUTION: (Lower right) Arrange the wireless LAN antenna cable (black) and Bluetooth antenna cable (brown) , and stick two acetate tapes in place. Wireless LAN antenna cable (black) Bluetooth antenna cable (brown) A cetate tape A cetate tape Ruled line Stand TECRA A9/TECRA S5/TECRA[...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna CAUTION: (Right side) Wireless LAN antenna (black cable) Bluetooth antenna cable (brown) Bluetooth antenna (brown cable) Wireless LAN antenna cable (black) A cetate tape A cetate tape 4-80 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures CAUTION: (Lower center) Secure the wireless LAN antenna cables and Bluetooth antenna cable with the insulator . Insulator Bluetooth antenna cable (brown) Wireless LAN antenna cable (black) Wireless LAN antenna cable (gray) Wireless LAN antenna cable (white) Insulator Wireless LAN [...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna CAUTION: (Lower center) Arrange the wireless LAN antenna cables (white and gray) and stick two acetate tapes in place. A cetate tape A cetate tape Wireless LAN antenna cable (gray) Wireless LAN antenna cable (white) Wireless LAN antenna cable (gray) Rubber cushion Rib Wireless LAN[...]

4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures CAUTION: (Upper left) Peel off the separators of the Wireless LAN antennas (white cable and gray cable) and stick the wireless LAN antenna (white cable and gray cable) to the display rear cover. Wireless LAN antenna (gray cable) Wireless LAN antenna (white cable) TECRA A9/TECRA S5[...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna CAUTION: (Left side) Arrange the wireless LAN antenna cables (white and gray) and stick three acetate tapes in place. Wireless LAN antenna cable (white) A cetate tape Wireless LAN antenna cable (gray) A cetate tape Wireless LAN antenna cable (gray) Wireless LAN antenna cable (whit[...]

4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures CAUTION: (Lower left) Arrange the wireless LAN antenna cable (black) and Bluetooth antenna cable (brown) , and stick two acetate tapes in place. A cetate tape A cetate tape Ruled line Wireless LAN antenna cable (gray) Wireless LAN antenna cable (white) Arrange the cables outside. [...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna CAUTION: (left side) Wireless LAN antenna cable (gray) Wireless LAN antenna cable (white) A cetate tape A cetate tape A cetate tape 4-86 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.27 LCD cable 4 Replacement Procedures 4.27 LCD cable Removing the LCD cable To remove the LCD cable, follow the steps below and refer to Figure 4-49. 1. Pass the LCD cable and the connector through the hole of the cover assembly and remove the LCD cable from the cover assem bly. LCD cable Connector Hole Hook Figure 4-49 Removing the LCD cable TEC[...]

4 Replacement Procedures 4.27 LCD cable 4-88 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) Installing the LCD cable To install the LCD cable, follow the steps below and refer to Figure 4-49. 1. Arrange the LCD cable to the hook of the cover assembly on the front. 2. Pass the LCD cable and the connector t[...]

4.28 Hinge 4 Replacement Procedures 4.28 Hinge Removing the Hinge To remove the hinge, follow the steps below and refer to Figure 4-50 and 4-51. 1. Remove the following screws . • M2.5 × 4B FLAT HEAD screw × 2 • M2.5 × 6C Tapping screw × 4 2. Stand the LCD mask and remove it. CAUTION : When standing the LCD mask, be careful not to hold the [...]

4 Replacement Procedures 4.28 Hinge 3. Remove the following screws securing the right hinge. • M2.5 × 4B FLAT HEAD screw × 1 • M2.5 × 6C Tapping screw × 1 4. Release two hooks and slide the right hinge inside to remove it through the hole. 5. Remove the following screw securing the left hinge. • M2.5 × 6C Tapping screw × 1 6. Release th[...]

4.28 Hinge 4 Replacement Procedures TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-91 Installing the Hinge To install the hinge, follow the steps below and refer to Figure 4-50 and 4-51. 1. Install the left hinge while engaging the hook and secure it with the following screw . • M2.5 × 6C Tapping scr[...]

4 Replacement Procedures 4.29 Speaker 4.29 Speaker Removing the Speaker To remove the speaker, follow the steps below and refer to Figure 4-52 to 4-54. 1. Peel off the insulator and pass the speaker cable through the hole of the cover assembly. 2. Remove the speakers from the slots and pass them through the holes of the cover assembly. Speaker (rig[...]

4.29 Speaker 4 Replacement Procedures Speaker (left) * Be careful of the direction, when installing. Hole Figure 4-53 Removing the speaker (2) 3. Separate the speakers (left and right) and speaker covers (left and right). Speaker cover * Be careful of the direction, when installing. Speaker (View from the back) Figure 4-54 Removing the speaker (3) [...]

4 Replacement Procedures 4.29 Speaker Installing the Speaker To install the speaker, follow the steps below and refer to Figure 4-52 to 4-55. 1. Install the speakers (left and right) to the speaker covers (left and right). 2. Arrange the speaker cable into the slot of the front of the cover assembly. 3. Pass the speakers through the holes of the co[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-95 4 4.30 Fluorescent Lamp This system uses LCD modules from the following suppliers. The procedure for replacing the fluorescent lamp is different for each LCD module. Refer to the appropriate procedure. Type P[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4.30.1 Replacing the 15.4-inch WXGA Samsung Fluorescent Lamp To replace the 15.4-inch WXGA Samsung fluorescent lam p, follow the steps below and refer to figures 4-56 to 4-59. Removing the fluorescent lamp 1. Remove the PCB cover. CAUTION : Handle with care not to damage COF of S/D ICs. PCB cover Figure[...]

4.30 Fluorescent Lamp 4 Replacement Procedure 2. Remove the yellow tapes, lamp-wire tape and Al tape. Lamp-wire tape Bottom Al tape Yellow tape (left) Yellow tape (right) Figure 4-57 Replacing Samsung fluorescent lamp (WXGA) (2) 3. Remove the top chassis from the m olded frame. CAUTION: Remove in the order of bottom hook and side hook. Figure 4-58 [...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4. Separate the panel assembly and backlight unit. CAUTION : Handle with care not to damage COF of S/D ICs. Panel assembly Figure 4-59 Replacing Samsung fluorescent lamp (WXGA) (4) 4-98 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633) [CONFIDENTIAL] 4-99 Assembling the fluorescent lamp The assembly procedure of the 15.4-inch Samsung fluorescent lam p is the reverse of the above disassembly procedure. Refer to figures 4-56 to 4-59. 1. Install the panel assembl[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4.30.2 Replacing the 15.4-inch WSXGA+ Samsung Fluorescent Lamp To replace the 15.4-inch WSXGA+ Samsung fluorescent lam p, follow the steps below and refer to figures 4-60 to 4-63. Removing the fluorescent lamp 1. Remove the PCB cover. CAUTION : Handle with care not to damage COF of S/D and G/D ICs. PCB [...]

4.30 Fluorescent Lamp 4 Replacement Procedure 2. Remove the white tapes, lamp-wire tape and Al tape. White tape (right) White tape (left) Lamp-wire tape Bottom Al tape Figure 4-61 Replacing Samsung fluorescent lamp (WSXGA+) (2) 3. Separate the top chassis and molded frame. CAUTION: Remove in the order of bottom hook and side hooks. Figure 4-62 Repl[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4. Separate the panel assembly and backlight unit. CAUTION : Handle with care not to damage COF of S/D and G/D ICs. Panel assembly Figure 4-63 Replacing Samsung fluorescent lamp (WSXGA+) (4) 4-102 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Ma intenance Manual (960-633) [C ONFIDENTIAL] 4-103 Assembling the fluorescent lamp The assembly procedure of the 15.4-inch Samsung fluorescent lam p is the reverse of the above disassembly procedure. Refer to figures 4-60 to 4-63. 1. Install the panel assem[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-104 [CONFIDENTIAL] TECRA A9/TECRA S5/TECRA P5/Satellite Pro S200 Main tenance Manual (960-633)[...]

[CONFIDENTIAL] Appendices[...]

Appendices App-ii [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[...]

Appendices TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CONFIDENTIAL] App-iii Appendix Content s Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ................................................................................................. B-1 B.1 Sys[...]

Appendices App-iv [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.22 J6051 External m icrophone connector (6-pin) ................................................... C-21 C.23 CN6170 Speaker connector (4-pin) .................................................................... C-21 C.24 J6310 Headphone connector (6-pin) .........[...]

Appendices TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CO NFIDENTIAL] App-v Appendix H EC/KBC rew rite Procedur es....................................................................... H-1 Appendix I Reliability ........................................................................................................ .I - 1[...]

Appendices App-vi [CONFIDENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Figures Figure B-1 System board ( FDBGS* ) layout (front) ....................................................... B-1 Figure B-2 System board ( FDBGS* ) layout (back) ....................................................... B-3 Figure B-3 GN board ( FDBGN* ) layout (f[...]

Appendices TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CO NFIDENTIAL] App-vii T able C-9 MDC interface connector (12-pin) ................................................................. C-16 T able C-10 Modem connector (4-pin)............................................................................... C-16 T able C-11 Keyboard interface [...]

Appendices App-viii [CONFIDENTIAL] TECRA A9( S5/P5/S200) Maintenance Manual (960-633) T able C-38 Serial connector (9-pin) .................................................................................. C-29 T able C-39 S-V ideo connector (4-pin) .............................................................................. C-29 T able D-1 Scan [...]

Appendix A Handling the LCD Module Appendices Appendix A P Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it [...]

Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface.[...]

Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. TECRA M9([...]

Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. A-4 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance [...]

Appendix A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These m aterials can release gas that can damage the panel’s polarization. TECRA M9(S5/P5/S200) [...]

Appendices Appendix A Handling the LCD Module A-6 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[...]

Appendix B Boar d Layout Appendices Appendix B Board Layout B.1 System Board (FHMLS*) Front View Figure B-1 System board (FHMLS*) layout (front) TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CO NFIDENTIAL] B-1[...]

Appendices Appendix B Boar d Layout B-2 [CONFIDENTIAL] TECRA A9( S5/P5/S200) Maintenance Manual (960-633) Table B-1 System board (FHMLS*) connectors (front) Number Name CN21 10 PC card interface connector CN2600 Mini PCI Express interface connector (Wireless LAN) CN3230 Keyboard interface connector CN3240 Dual Point interface connector CN3490 (Debu[...]

Appendix B Boar d Layout Appendices B.2 System Board (FHMLS *) Back View Figure B-2 System board (FHMLS*) layout (back) TECRA A9(S5/P5/S200) Maintenance Manual (960-633) [ CONFIDENTIAL] B-3[...]

Appendices Appendix B Boar d Layout B-4 [CONFIDENTIAL] TECRA A9( S5/P5/S200) Maintenance Manual (960-633) Table B-2 System board( FHMLS*) ICs and connectors (back) Number Name IS1050 CPU socket IC1200 Intel 965GM/GML (Northbridge) IC1600 ICH8-M(Southbridge) IC5000 nVIDIA G8M CN1400 SO-DIMM0 connector A CN1410 SO-DIMM0 connector B CN1810 ODD interfa[...]

Appendix B Boar d Layout Appendices B.3 Serial & RGB Board (FHMLR*) Front View (front) Figure B-3 Serial & RGB Board (FHMLR*) layout (front) Table B-3 Serial & RGB (FHMLR*) connectors (front) Number Name CN5080 RGB interface connector CN9600 System board interface connector CN9601 Serial interface connector TECRA A9(S5/P5/S200) Maintena[...]

Appendices Appendix B Boar d Layout B.4 Fingerprint sensor Board (FHMLF*) Front and Back View (front) (back) Figure B-4 Fingerprint sensor Boar d (FHMLF*) layout (front/back) Table B-4 Fingerprint sensor B oard (FHMLF*) connector (front) Number Name CN9650 System board interface connector B-6 [CONFIDENTIAL] TECRA A9( S5/P5/S200) Maintenance Manual [...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-1 Appendix C Appendix C Pin Assignments System board (FHMLS*) C.1 CN1400 SO-DIMM0 connector (200-pin) Table C-1 SO-DIMM0 connector (200-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRVREF-B0V I 2 GND - 3 GND - 4 ADQ04-B1P I/O 5 A[...]

Appendices Appendix C Pin Assignments C-2 [CONFID ENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Table C-1 SO-DIMM0 connector (200-pin) (2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 63 ADQ29-B1P I/O 64 ADQ24-B1P I/O 65 GND - 66 GND - 67 ADM3-B1P I 68 ADQS3-B1N I/O 69 N.C. - 70 ADQS3-B1P I/O 71 GND - 72 GND - 73 ADQ30-B1P I/O 74 [...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-3 Table C-1 SO-DIMM0 connector (200-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 133 GND - 134 ADQ37-B1P I/O 135 ADQ38-B1P I/O 136 ADQ34-B1P I/O 137 ADQ39-B1P I/O 138 GND - 139 GND - 140 ADQ41-B1P I/O 141 ADQ44-B1P I/O 142 ADQ45-B1[...]

Appendices Appendix C Pin Assignments C-4 [CONFID ENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) C.2 CN1410 SO-DIMM1 connector (200-pin) Table C-2 SO-DIMM1 connector (200-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRVREF-B0V I 2 GND - 3 GND - 4 BDQ01-B1P I/O 5 BDQ04-B1P I/O 6 BDQ00-B1P I/O 7 BDQ05-B1P I/O 8 GND - 9 GND[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-5 Table C-2 SO-DIMM1 connector (200-pin) (2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 63 BDQ29-B1P I/O 64 BDQ28-B1P I/O 65 GND - 66 GND - 67 BDM3-B1P I 68 BDQS3-B1N I/O 69 N.C. - 70 BDQS3-B1P I/O 71 GND - 72 GND - 73 BDQ31-B1P I/O 74 BD[...]

Appendices Appendix C Pin Assignments C-6 [CONFID ENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) Table C-2 SO-DIMM1 connector (200-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 135 BDQ35-B1P I/O 136 BDQ32-B1P I/O 137 BDQ33-B1P I/O 138 GND - 139 GND - 140 BDQ43-B1P I/O 141 BDQ40-B1P I/O 142 BDQ46-B1P I/O 143 BDQ45-B1P I/O 14[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-7 C.3 CN1810 ODD interface connector (50-pin) Table C-3 ODD interface connector (50-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 - 2 - 3 - 4 - 5 RLTRS3&RSTIDB O 6 PDD08-P3P I/O 7 PDD07-P3P I/O 8 PDD09-P3P I/O 9 PDD06-P3P I/O 10 PDD[...]

Appendices Appendix C Pin Assignments C-8 [CONFID ENTIAL] TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633) C.4 CN1900 HDD(SATA) interface connector (11-pin) Table C-4 HDD(SATA) interface connector (11-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 ZSATT0-P1P O 2 ZSATT0-P1N O 3 GND - 4 ZSATR0-P1N I 5 ZSATR0-P1P I 6 GND - 7 P3V - 8 GND - 9 [...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-9 C.5 CN2110 PC card interface connector (70-pin) Table C-5 PC card interface connector (70-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 2 ACAD00-PYP I/O 3 ACAD01-PYP I/O 4 ACAD03-PYP I/O 5 ACAD05-PYP I/O 6 ACAD07-PYP I/O 7 ACCBE[...]

Appendices Appendix C Pin Assignments C-10 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.6 IS2150 Bridge Media interface connector (46-pin) Table C-6 Bridge Media interface connector (46-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SDCD-P3N O 2 GND - 3 MSDAT1-P3P I/O 4 MSSDIO-P3P I/O 5 - 6 GND - 7 - 8 MSCLK-P3P I/O 9 G[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-11 C.7 CN2300 Docking interface connector (133-pin) Table C-7 Docking interface connector (133-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DCOUT I 2 DCOUT I 3 DOCDT1-S3N O 4 GND - 5 NC - 6 NC - 7 NC - 8 NC - 9 GND - 10 ZUSBDC-E3[...]

Appendices Appendix C Pin Assignments C-12 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table C-7 Docking interface connector (133-pin) (2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 69 ZBIDCN-EXN 70 ZBIDCP-EXP 71 DCOUT I 72 DCOUT I 73 PWRSW-S3N O 74 DDCON-P5P I 75 NC - 76 NC - 77 GND - 78 GND - 79 GND - 80 NC - 81 GND - 8[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-13 Table C-7 Docking interface connector (133-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O A1 GND - A2 GND - A3 DSKDC - A4 - 1T GND - 2T GND - 3T GND - 4T GND - 5T GND - 6T GND - 7T GND - 8T GND - 9T GND - 10T GND - 11T GND - 12T G[...]

Appendices Appendix C Pin Assignments C-14 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.8 CN2600 Mini PCI Express I/F connector (W-LAN)(52-pin) Table C-8 Mini PCI Express interface connector (52-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PEWAKE-E3N O 2 P3V I 3 WCHDAT-P3P O 4 GND - 5 WCHCLK-P3P O 6 1R5-P1V I 7 MPEXRQ[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-15 C.9 CN2650 Mini PCI Express I/F connector(Robson) (52-pin) Table C-9 Mini PCI Express interface connector (52-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 2 P3V 3 4 GND 5 6 1R5-P1V 7 ROBXRQ-P3N I 8 9 GND 10 11 XPEROB-P0N I 12 13 XPE[...]

Appendices Appendix C Pin Assignments C-16 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.10 CN3010 MDC interface connector (12-pin) Table C-10 MDC interface connector (12-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 2 NC - 3 AZSDO1-P3P I/O 4 NC - 5 GND - 6 E3V I 7 AZSYC1-P3P 8 GND - 9 (IC3010-1) I/O 10 GND - 11 A[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-17 C.12 CN3240 Dual Point interface connector (8-pin) Table C-12 Dual Point interface connector (8-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SP-P5V - 2 SPX-PXP O 3 SPY-PXP O 4 SP-GND - 5 GND - 6 IPDCLK-P5P I/O 7 IPDDAT-P5P I/O 8 P5V[...]

Appendices Appendix C Pin Assignments C-18 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.15 CN4230 IEEE 1394 interface connector (4-pin) Table C-15 IEEE 1394 interface connector (4-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 ZTPB0-P3N I/O 2 ZTPB0-P3P I/O 3 ZTPA0-P3N I/O 4 ZTPA0-P3P I/O 1T GND - 2T GND - 3T GND - 4T GN[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-19 C.17 CN4440 Bluetooth2 interface connector (20-pin) Table C-17 Bluetooth2 interface connector (20-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 2 ZUSBB2-E3P I/O 3 ZUSBB2-E3N I/O 4 WCHCL2-P3P O 5 BTMDL2-P3N I 6 BTRST2-S3N O 7 WC[...]

Appendices Appendix C Pin Assignments C-20 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.20 CN5000 LCD interface connector (40-pin) Table C-20 LCD interface connector (40-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 FL-P5V I 2 FL-P5V I 3 FL-P5V I 4 NC - 5 GND - 6 GND - 7 GND - 8 (BRT2DA-S3P) - 9 (BRT10-P5P) - 10 (BRT0)[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-21 C.21 CN6050 Internal microphone connector (2-pin) Table C-21 Internal microphone connector (2-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 (IMICIN-PXP) I 2 A-GND - C.22 J6051 External microphone connector (6-pin) Table C-22External [...]

Appendices Appendix C Pin Assignments C-22 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.24 J6310 Headphone connector (6-pin) Table C-24 Headphone connector (6-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 A-GND - 2 HEADL-PXP O 3 HEADR-PXP O 4 DETCTA-P4N O 5 A-GND - 6 NC - C.25 CN8771 FAN interface connector (4-pin) Tab[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-23 C.28 CN9300 RTC Battery connector (3-pin) Table C-28 RTC Battery connector (3-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 (R3V) - 2 NC - 3 GND - 1T GND - 2T GND - C.29 CN9500 Serial & RGB board(FHMLR*) I/F connector (40-pin) Ta[...]

Appendices Appendix C Pin Assignments C-24 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.30 CN9540 Web Camera interface connector (3-pin) Table C-30 Web Camera interface connector (3-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 P5V - 2 ZUSBCM-E3N I 3 ZUSBCM-E3P I 4 GND - 5 GND - 6 GND - C.31 CN9550 Fingerprint sensor b[...]

Appendix C Pin Assignments Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] C-25 Serial & RGB board (FHMLR*) C.33 CN5080 RGB interface connector (15-pin) Table C-33 RGB interface connector (15-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRED-PXP O 2 MGRN-PXP O 3 MBLU-PXP O 4 NC - 5 GND - 6 GND - 7 GND - 8 G[...]

Appendices Appendix C Pin Assignments C-26 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) C.35 CN9601 Serial interface connector (9-pin) Table C-35 Serial interface connector (9-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DCD-PYN I 2 RXD-PYN I 3 TXD-PYN O 4 DTR-PYP O 5 GND - 6 DSR-PYP I 7 RTS-PYP O 8 CTS-PYP I 9 RING-PYP[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] D- 1 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E[...]

Appendices Appendix D Keyboard Scan/Character Codes D-2 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 ¦ 2B AB 5D F0 5D *2 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] D- 3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75[...]

Appendices Appendix D Keyboard Scan/Character Codes D-4 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc Refer to table 2-25 126 Pause Refer to table 2-25 202 Fn [...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] D- 5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL [...]

Appendices Appendix D Keyboard Scan/Character Codes D-6 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[CONFIDENTIAL] D- 7 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D [...]

Appendices Appendix D Keyboard Scan/Character Codes D-8 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual (960-633) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm on * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix E Key Layout Appendices 4 Appendix E Key Layout 4.31 E.1 United Kingdom (UK) Keyboard Figur e E-1 UK keyboard 4.31 E.2 United States (US) Keyboard Figur e E-2 US keyboard TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CO NFIDENTIAL] E-1[...]

Appendices Appendix E Key Layout E-2 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[...]

Appendix F W iring diagrams Appendices 4 Appendix F Wiring diagrams F.1 RGB Monitor Loopback Connector Figur e F-1 RGB Monitor Loopback Connector F.2 RS-232C Loopback Connector Figur e F-2 RS-232C Loopback Connector TECRA A9(S5/P5/S200) Maintenance Manual (960-633) [CONFIDENTIAL] F-1[...]

Appendices Appendix F W iring diagrams F.3 RS-232C direct connection cable (9-pin to 9-pin) Figur e F-3 RS-232C direct connection cable (9-pin to 9-pin) F.4 RS-232C direct connection cable (9-pin to 25-pin) Figur e F-4 RS-232C direct connection cable (9-pin to 25-pin) F-2 [CONFIDENTIAL] TECRA A9( S5/P5/S200) Maintenance Manual (960-633)[...]

Appendix F W iring diagrams Appendices F.5 LAN Loopback Connector Figur e F-5 LAN Loopback Connector TECRA A9(S5/P5/S200) Maintenance Manual (960-633) [CONFIDENTIAL] F-3[...]

Appendices Appendix F W iring diagrams F-4 [CONFIDENTIAL] TECRA A9( S5/P5/S200) Maintenance Manual (960-633)[...]

Appendix G BIOS r ewrite procedur es Appendices 4 Appendix G BIOS rewrite procedures This Appendix explains how to rewrite th e system BIOS program when you update the system BIOS. Tools T o rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk for the com puter that has renewed BIOS data. Rewriting the BIOS 1. Set the syste[...]

Appendices Appendix G BIOS r ewrite procedur es G-2 [CONFIDE NTIAL] TECRA A9( S5/P5/S200) Maintenance Manual (960-633)[...]

Appendix H EC/KBC r ewrite procedur es Appendices TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CO NFIDENTIAL] H-1 4 Appendix H EC/KBC rewrite procedures This Appendix explains how to rewrite th e EC/KBC system program when you update the EC/KBC system. Tools T o rewrite the EC/KBC, you need the following tool:  EC/KBC rewriting disk for the[...]

Appendices Appendix H EC/KBC r ewrite procedur es H-2 [CONFIDE NTIAL] TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[...]

Appendix I Reliability Appendices TECRA A9(S5/P5/S200) Maintenance Manual (960-633)[CO NFIDENTIAL] I-1 4 Appendix I Reliability The following table shows MTBF (Mean T ime Between Failures). Table I-1 MTBF Time (hours) MTBF 5161[...]

Appendices Appendix I Reliability I-2 [CONFIDENTIAL]TECRA A9(S5/P5/S200) Maintenance Manual ( 960-633)[...]