Aiwa 586IVX manuale d’uso

586IV X Re v . 2 + System Boar d Use r ’ s Manua l - 32970703 -[...]

FCC Statement on Class B This equipment has been tested and found to comply with the limits fo r a Class B digital device, pursuant to Part 15 of the FCC rules. Thes e limits are designed to provide reasonable protection against harmful in - terference when the equipment is operated in a residential installation . This equipment generates, uses and[...]

Table of Content s Chapter 1: Introductio n ............................................................ 5 Features and Specification s .................................................. 6 Package Checklis t .............................................................. 8 Chapter 2: Hardware Installatio n ...........................................[...]

4 Save & Exit Setu p ........................................................ 5 3 Exit Without Savin g ....................................................... 5 4 Desktop Management Interface (DMI ) .................................... 5 6 System Error Repor t .......................................................... 5 4 IDE Device Driver s ..[...]

5 The 586IVX is a Pentiu m  processor-class system board supportin g Intel Pentiu m  Processor with MMX Technology and Intel Pentiu m  pro - cessors running at 75MHz, 90MHz, 100MHz, 120MHz, 133MHz, 150MHz, 166MHz and 200MHz frequencies. The 58 6 IV X also support s Cyri x  6x86 ™ P120+/P133+/P150+/P166+ and AMD-K5 PR75/PR90 / PR100/PR[...]

6 Features and Specification s Processo r • Intel Pentiu m  Processor with MM X  Technology - 166/20 0 • Intel Pentiu m  75/90/100/120/133/150/166/200MH z • Future Pentiu m  OverDrive processo r • Cyri x  6x86 ™ P120+/P133+/P150+/P166 + • AMD-K5 PR75/PR90/PR100/PR120/PR133/PR16 6 Chipse t • Intel 82430VX PCIse t Cache M[...]

7 • Soft Power supporte d PCI IDE Interfac e • PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up t o 16.6MB/sec. ) • DMA Mode 2 Bus Master IDE (data transfer rate up to 22.2MB/sec. ) • Bus mastering reduces CPU utilization during disk transfe r • ATAPI IDE CD-ROM supporte d Integrated I/ O • Two NS16C550A-compatible high speed U[...]

8 Package Checklis t The 586IVX package contains the following items : • The 586IVX system boar d • The 586IVX user ’ s manua l • One 40-pin IDE hard disk cabl e • One 34-pin floppy disk drive cabl e • One IDE driver diskett e • Five spare jumper s If any of these items are missing or damaged, please contact you r dealer or sales repr[...]

9 Chapter 2 Hardware Installatio n This chapter summarizes the steps to install the 586IVX system boar d into your system unit. It also includes a description of the area in whic h you must work and directions for memory installation. Before installin g the system board, obtain the memory you plan to install. Refer to th e System Memory section for[...]

10 Static Electricity Precaution s 1 . To prevent electrostatic build-up, leave the board in its anti-stati c bag until you are ready to install it . 2 . Wear an antistatic wrist strap . 3 . Do all preparation work on a static-free surface with the syste m board components facing up . 4 . Hold the system board by its edges only. Be careful not to t[...]

11 2 . Remove the system unit cover. Refer to the manufacturer ’ s instruc - tions if necessary . 3 . Detach all connectors from the old system board and remove ex - pansion cards seated in any expansion slots . 4 . Loosen the screws holding the original system board and remov e the board from the system. Save the screws . 5 . Remove the 586IVX f[...]

12 Board La you t square denotes pin 1 U29 ISA Slot 4 ISA Slot 3 ISA Slot 2 ISA Slot 1 PCI Slot 4 PCI Slot 3 PCI Slot 2 PCI Slot 1 S oc k e t 7 S oc k e t 7 Pin 1 1 2 4 3 JP7 1 5 6 2 1 5 6 2 JP2 JP3 1 2 4 3 JP4 JP5 J8 Primary IDE Secondary IDE J11 J12 82438VX J10 Floppy JP12 JP 11 JP10 J9 ATX Power Connector JP1 J3 BIOS 82371S B 82438VX SRA M Batte[...]

13 Jumper s JP2-JP5, JP7, JP10-JP1 2 Intel, Cyrix and AMD processor s JP1 - CMOS clea r JP13 - Password clea r Socket s SM1 to SM4 - SIMM socket s U29 - ZIF socke t J 2 - USB 1 por t J 4 - USB 2 por t J 8 - IrDA connecto r J 9 - Fan connecto r J1 0 - FDD connecto r J1 1 - Primary IDE HDD connecto r J1 2 - Secondary IDE HDD connecto r J1 3 - ATX pow[...]

14 SIM M The SIMM (Single In-line Memory Module) sockets are divided into tw o banks on the system board, Bank 0 and Bank 1. Each bank consists o f 2 SIMM sockets . You will need either 2 or 4 pieces of SIM modules, depending on th e amount of memory you intend to install. The system board will not wor k if you install 1 or 3 pieces. Make sure you [...]

15 The table below summarizes the bank locations and modules neede d for the corresponding memory sizes . Memory Siz e 8M B 8M B 16M B 16M B 16M B 24M B 24M B 32M B 32M B 40M B 40M B 48M B 48M B 64M B 64M B 64M B 72M B 72M B 80M B 80M B 96M B 96M B 128M B Bank 0 SIMM 1 1MBx3 2 — 2MBx3 2 — 1MBx3 2 1MBx3 2 2MBx3 2 4MBx3 2 2MBx3 2 1MBx3 2 4MBx3 2 [...]

16 Cache Memor y The 586IVX system board can support 256KB pipeline burst, direct ma p write-back cache SRAM. Your system board may come with 256K B cache mounted at locations U11 and U17 of the system board . 1 . Position the SIMM above the socket with the “ notch ” in the modul e aligned with the “ key ” on the socket . 2 . Seat the modul[...]

17 CPU Installatio n The 586IVX allows for easy installation of CPUs. Make sure all jumpers ar e set correctly before applying power or you may damage the CPU or syste m board. Use a needle-nosed plier to move the jumpers if necessary . Jumpers JP10, JP11 and JP12 are used to set the external bus clock o f your processor. Refer to the following pag[...]

18 Jumper Settings for Intel Processor s Voltage s 2.7 V 2.8 V 2.9 V 3.3V * (VR/STD ) 3.5 V (VRE ) JP 2 1-3, 2-4 O n 1-3, 2-4 O n 1-3, 2-4 O n 3-5, 4-6 O n 3-5, 4-6 O n JP 3 1-2 O n 3-4 O n 5-6 O n 3-4 O n 3-4 O n JP 4 3-4 O n 3-4 O n 3-4 O n 3-4 O n 1-2 O n JP 7 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 O n 1-2, 3-4 O n Intel Processor s [...]

19 Jumper Settings for Cyrix 6x86 Processor s JP1 0 1-2 O n 2-3 O n 1-2 O n 1-2 O n JP1 1 1-2 O n 1-2 O n 2-3 O n 1-2 O n JP1 2 1-2 O n 1-2 O n 1-2 O n 2-3 O n JP 5 3-5 On, 2-4 O n Cyrix CPU s P120 + P133 + P150 + P166 + Ext. Bu s CL K 50MH z 55MH z 60MH z 66MH z Cyrix CPU s P120+/P133+ / P150+/P166 + Freq. Rati o 2 x Voltage s 2.7 V 2.8 V 2.9 V 3.[...]

20 Jumper Settings for AMD-K5 Processor s Voltage s 2.7 V 2.8 V 2.9 V 3.3V * (VR/STD ) 3.5 V (VRE ) JP 2 1-3, 2-4 O n 1-3, 2-4 O n 1-3, 2-4 O n 3-5, 4-6 O n 3-5, 4-6 O n JP 3 1-2 O n 3-4 O n 5-6 O n 3-4 O n 3-4 O n JP 4 3-4 O n 3-4 O n 3-4 O n 3-4 O n 1-2 O n JP 7 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 O n 1-2, 3-4 O n P-Ratin g PR7 5 P[...]

21 Installing Upgrade CPU s The 586IVX is equipped with a 321-pin Zero Insertion Force (ZIF) socket at location U29 of the system board. Refer to page 12 for th e location of the ZIF socket. This socket is designed for easy removal o f an old CPU and easy insertion of an upgrade CPU. The ZIF socke t allows you to carefully place the new CPU into it[...]

22 Lifting the Handl e 2 . Once the lever is completely up, remove the old CPU carefully b y lifting it straight out of the socket. You are now ready to insert th e new CPU . 3 . Position the CPU above the ZIF socket. Make sure pin 1 of th e CPU is aligned with pin 1 of the socket. Lower the chip until th e pins are inserted properly in their corre[...]

23 4 . Push the handle down until the handle locks into place. The to p plate will slide forward. You will feel some resistance as pressur e starts to secure the CPU in the socket. This is normal and will no t damage the CPU. However, if the handle is not completely closed , damage to the CPU and/or system board may result . Positioning the CPU Abo[...]

24 least 3 of 4 sides of the processor and heatsink must be at least 0. 2 inches. All cables (for floppy drive, hard drive, CD-ROM, etc.) must b e routed clear of the CPU and its airspace . Fan Exhaus t The CPU must be kept cool by using a fan with heatsink. The tempera - ture of the air entering the fan/heatsink cannot exceed 4 5 o C (11 3 o F) . [...]

25 Built-in Port s The 586IVX system board is equipped with two serial ports, one paralle l printer port, one shrouded floppy disk header, two shrouded IDE har d disk headers, and two USB ports. Refer to page 12 for the locations o f the built-in connectors and pin 1 of those connectors . PS/ 2 Mous e PS/ 2 K/ B USB 1 USB 2 Parallel Printe r COM 2 [...]

26 I/O Addres s 3BC-3BE He x 378-37 A Hex (default ) 278-27 A He x Serial Port s The 586IVX is equipped with two serial ports at locations CN5 (COM 2 ) and CN6 (COM 1) of the system board. These built-in serial ports ar e RS-232C asynchronous communication ports with 16C550A-compatibl e UARTs that can be used with modems, serial printers, remote di[...]

27 IDE Hard Disk Interfac e The 586IVX system board is equipped with two shrouded PCI ID E headers that will interface four Enhanced IDE (Integrated Drive Elec - tronics) hard disk drives . Note : Only Enhanced IDE hard drives or ATAPI CD-ROMs can be connecte d to the IDE interface . Connecting the IDE Hard Disk Interfac e To prevent improper IDE c[...]

28 Heade r Note : An IDE cable with a standard 40-pin connector (without the keyin g mechanism) can be installed in the shrouded PCI IDE header. Be ex - tremely careful to match the colored edge of the ribbon with pin 1 of th e header . Connecting the Hard Disk Cabl e 1 . If you are connecting two hard drives, install the 40-pin connector o f the I[...]

29 We recommend that you use Enhanced IDE hard drives from the sam e manufacturer. In a few cases, drives from two different manufacturer s will not function properly when used together. The problem lies in th e hard drives, not the 586IVX system board . Preparing an IDE Drive for Us e IDE disk drives are already low-level formatted, with any bad-t[...]

30 Installing Expansion Card s The 586IVX system board is equipped with 3 dedicated PCI slots, 3 dedicated 16-bit ISA slots and 1 shared PCI/ISA slot. All PCI slots ar e bus masters. Refer to page 12 for the locations of the expansion slots .[...]

31 Chapter 3 Software Installatio n After you power up your system, the BIOS message appears on you r screen and the memory count begins . After the memory test, the following message will appear on the screen : Press DEL to enter setu p If the message disappears before you respond, restart your system o r press the “ Reset ” button located on [...]

32 MODE Auto Auto Auto Auto Use the arrow keys to highlight the option you want and press <Enter> . The following describes each of these options . Note : The settings on the BIOS setup screens on the following pages are fo r reference only. Some of the settings will vary according to your system ’ s configuration and should not be referred[...]

33 Dat e The date format is <day>, <month>, <date>, <year> . Da y Mont h Dat e Yea r Displays a da y , from Sunday to Saturda y Displays the month, from January to Decembe r Displays the date, from 1 to 3 1 Displays the yea r, from 1900 to 209 9 Tim e The time format is <hour>, <minute>, <second>. The time [...]

34 Note : Choosing an incorrect type might cause your system to format the flopp y disk improperl y , and you will not be able to access your data . Drive A and Drive B These categories identify the types of floppy disk drives installed. Th e following are the options for drives A and B . Non e 360K, 5.25 in . 1.2M, 5.25 in . 720K, 3.5 in . 1.44M, [...]

35 Vide o This category selects the type of video adapter used for the primar y system monito r. Although secondary monitors are supported, you do no t have to select the type in Setup. The default setting is EGA/VG A (BIO S default, Setup default) . EGA/VG A CGA 4 0 CGA 8 0 Mon o Enhanced Graphics Adapter/Video Graphics Arra y . For EGA , VGA, SVG[...]

36 BIOS Features Setu p The BIOS Features Setup allows you to configure your system for basi c operation. Some entries are defaults required by the system board , while others, if enabled, will improve the performance of your system o r let you set some features according to your preference . Bas e Memor y Extende d Memor y Othe r Memor y This refe[...]

37 ! WARNING ! Disk boot sector is to be modifie d Type “ Y ” to accept write or “ N ” to abort writ e Award Software, Inc . After seeing this message, if necessary, you will be able to run an anti - virus program to locate and remove the problem before any damage i s done . Many disk diagnostic programs which attempt to access the boot sec[...]

38 A, C C, A CDROM, C, A C, CDROM, A The system will first search for a floppy drive and then a hard disk drive . The system will first search for a hard disk drive an d then a floppy drive . The system will first search for a CD-ROM drive, then a hard disk drive and then a floppy drive . The system will first search for a hard disk drive, then a C[...]

39 Boot Up NumLock Statu s This allows you to determine the default state of the numeric keypad . By default, the system boots up with NumLock on . The function of the numeric keypad is the number keys . The function of the numeric keypad is the arrow keys . O n Of f Security Optio n This category allows you to limit access to your system and Setup[...]

40 Enable d Disable d Video shadow is enabled . Video shadow is disabled . C8000-CBFFF Shadow to DC000-DFFFF Shado w These categories determine whether option ROMs will be copied t o RAM . Chipset Features Setu p This section gives you instructions on how to configure the syste m based on the specific features of the chipset. The chipset manages bu[...]

41 Power Managemen t This category allows you to select the type (or degree) of power savin g by changing the length of idle time that elapses before each of th e following modes are activated: Doze Mode, Standby Mode, and Sus - pend Mode . No power management. Disables the Doze, Standby an d Suspend modes . Minimum power management. Doze Mode = 1 [...]

42 Video Off Metho d This determines the manner in which the monitor is blanked . MODEM Use IR Q This category is used to set an IRQ channel (IRQ 3, 4, 5, 7, 9, 10 o r 11) for the modem installed in your system . Doze Mode, Standby Mode, Suspend Mode and HDD Power Dow n These Green PC power saving categories are user configurable onl y when the Pow[...]

43 IRQ3-IRQ15 ( Wake Up Events in Doze & Standby and Powe r Down & Resume Events ) These are I/O events whose occurrence can prevent the system fro m entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything which occurs to a device which is configured as enabled, even when the [...]

44 Resources Controlled B y The Award Plug and Play BIOS has the capacity to automatically con - figure all of the boot and Plug and Play compatible devices . The system will automatically detect the settings for you. Th e categories that follow will not be shown on the PNP/PCI Con - figuration screen . This allows you to set the IRQ/DMA (you have [...]

45 Primary IDE INT# and Secondary IDE INT # The Primary and Secondary IDE INT# categories are used to select th e PCI interrupt (A, B, C, or D) that is associated with the connected har d drives . Load BIOS Default s The “ Load BIOS Defaults ” option loads the troubleshooting default val - ues permanently stored in the ROM chips. These settings[...]

46 On-Chip Primary PCI IDE and On-Chip Secondary PCI ID E These categories allow you to enable or disable the primary and sec - ondary IDE controller. The default is Enabled. Select Disabled if yo u want to add a different hard drive controller . Integrated Peripheral s IDE HDD Block Mod e Enable d Disable d The IDE HDD uses the block mode. The sys[...]

47 PCI Slot IDE 2nd Channe l This allows you to designate an IDE controller card inserted into one o f the PCI slots as your secondary IDE controller . The IDE controller card is designated as the secondary ID E controller . No IDE controller card occupying any of the PCI slots . Enable d Disable d Onboard FDD Controlle r Enables the onboard floppy[...]

48 Uses the COM 2 serial port . HP mode IrDA . SHARP mode IrDA . Standar d HPSI R ASKI R Onboard Parallel Por t Selects the I/O address and IRQ for the onboard parallel port . Disables the onboard parallel port . 378H/IRQ 7 3BCH/IRQ 7 278H/IRQ 5 Disable d Parallel Port Mod e Selects the parallel port mode according to the type of printe r device co[...]

49 Type in the password. You are limited to eight characters. When done , the message below will appear : Confirm Password : You are being asked to verify the password. Type in exactly the sam e password. If you type in a wrong password, you will be prompted t o enter the correct password again . To delete or disable the password function, highligh[...]

50 ROM PCI/ISA BIOS CMOS SETUP UTILITY AW ARD SOFT WARE, INC. HARD DISKS TYPE SIZE CYLS HEAD RECOMP LANDZ SECTOR MODE Primary Master: Select Primary Master Option (N=Skip): N OPTIONS SIZE CYLS HEAD RECOMP LANDZ SECTOR MODE 2 (Y) 853 827 32 0 1653 63 LBA 1 853 1654 16 65535 1653 63 Normal 3 853 827 32 65536 1653 63 Large Note: Some OS (like SCO-UNIX[...]

51 If you set your HDD to Normal mode, the maximum accessible HDD wil l be 528 megabytes even though the physical size of the HDD may b e greater than that . LBA (Logical Block Addressing) Mod e LBA mode is a HDD accessing method to overcome the 528 megabyt e limitation. The number of cylinders, heads and sectors shown on th e screen may not be the[...]

52 HDD Low Level Forma t The HDD Low Level Format utility is designed as a tool to save yo u time formatting your hard disk. It automatically looks for the necessar y information of the drive you selected. This utility also searches for ba d tracks and lists them for your reference. Highlight this option and pres s <Enter>. A screen similar t[...]

53 Save & Exit Setu p When all the changes have been made, highlight “ Save & Exit Setup ” and press <Enter>. The message below will appear : Save to CMOS and Exit (Y/N)? N Type “ Y ” and press <Enter>. The modifications you have made will b e written into the CMOS memory, and the system will reboot. You wil l once again[...]

54 Play BIOS. Additional information, such as ISA based peripherals, which may not be automatically detected, can be manually recorded i n the DMI pool by using the Add DMI menu. The DMI pool data is the n verified or updated whenever the system hardware or setup is altered . Running the DMI Utilit y To run the DMI utility, type: DMICFG.EXE. You ca[...]

55 Edit DM I 1 . Use the ← o r → arrow keys to select the Edit DMI menu . 2 . Highlight the item on the left screen that you would like to edit b y using the ↑ or ↓ arrow keys, then press <Enter> . 3 . The cursor will move to the screen you select allowing you to edi t information. The screen will also display the auto-detected inform[...]

56 System Error Repor t When the BIOS encounters an error that requires the user to correc t something, either a beep code will sound or a message will be dis - played in a box in the middle of the screen and the message, PRES S F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will b e shown in the information box at the bottom. Enter Setup to c[...]

57 Error Message s One or more of the following messages may be displayed if the BIO S detects an error during the POST. This list indicates the error message s for all Awards BIOSes : CMOS BATTERY HAS FAILE D The CMOS battery is no longer functional. It should be replaced . CMOS CHECKSUM ERRO R Checksum of CMOS is incorrect. This can indicate that[...]

58 Hard Disk(s) fail (08 ) Sector Verify failed . Keyboard is locked out - Unlock the ke y The BIOS detects that the keyboard is locked. Keyboard controller i s pulled low . Keyboard error or no keyboard presen t Cannot initialize the keyboard. Make sure the keyboard is attache d correctly and no keys are being pressed during the boot . Manufacturi[...]

59 Chapter 4 T roubleshooting Checklis t This chapter of the manual is designed to help you with problems tha t you may encounter with your personal compute r . To efficiently troubleshoot your system, treat each problem individuall y . This is t o ensure an accurate diagnosis of the problem in case a problem ha s multiple causes . Some of the most[...]

60 Hard Driv e Hard disk failure . 1 . Make sure the correct drive type for the hard disk drive has bee n entered in the BIOS . 2 . If the system is configured with two hard drives, make sure th e bootable (first) hard drive is configured as Master and the secon d hard drive is configured as Slave . Excessively long formatting period . 1 . If your [...]

61 3 . Verify that the attached serial device works by attaching it to a seria l port that is working and configured correctl y . If the serial devic e does not work, either the cable or the serial device has a problem. I f the serial device works, the problem may be due to the onboard I/ O or the address setting . 4 . Make sure the COM port settin[...]

62 SIM M 1MBx3 2 2MBx3 2 4MBx3 2 8MBx3 2 Bran d Fujits u OK I OK I NE C Micro n T I Micro n Micro n NE C Hitach i Fujits u Mitsubish i Hitach i NE C NE C NE C Chip Numbe r 81C1000A-7 0 M51440A-7 0 M511000B-7 0 424400-6 0 40447-6 0 TMS4400DJ-7 0 MT4C4007-70 (EDO ) MT4C4007-60 (EDO ) 4218165-60 (EDO ) 7400AS-7 0 8117400-7 0 422A06-7 0 5117400AS-7 0 4[...]

63 Memory Address Ma p Addres s Nam e Functio n 0000000 t o 640KB Syste m System Board Memor y 009FFF F Board RA M 00A0000 t o 128KB Vide o Reserved for Graphic s 00BFFF F Display Memor y Display Memor y 00C0000 t o 160KB I/ O Reserved for ROM o n 00E7FF F Expansion RO M I/O Adapter Car d 00E8000 t o 96KB ROM o n System Board BIO S 00FFFF F the Sys[...]

64 Note : The I/O address hex 0000 to 00FF are reserved for the system boar d I/O. Hex 0100 to 03FF are available on the I/O channels . I/O Address Ma p I/O Addres s Functio n 0000-001 F DMA Controller 1, 8237A- 5 0020-003 F Interrupt Controller 1, 8259A, Maste r 0040-005 F Time r , 8254- 2 0060-006 F 8742 (Keyboard Controller ) 0070-007 F Real-tim[...]

65 Appendix C Connector s Connector s J 2 J 4 J 8 J 9 J1 0 J1 1 J1 2 J1 3 CN 1 CN 5 CN 6 CN 7 USB 1 connecto r USB 2 connecto r IrDA connecto r Fan connecto r Floppy disk drive connecto r Primary IDE hard disk drive connecto r Secondary IDE hard disk drive connecto r ATX power LE D HD LE D Green LE D ATX power switc h Green switc h Reset switc h AT[...]

66 CN 8 CN 9 PL 1 PS/2 mouse por t Game por t ATX power connecto r J8 J11 J12 J10 J9 PL1 J13 CN6 CN5 J4 CN1 CN8 J2 CN7[...]

67 Pi n 1 2 3 Functio n Groun d +12 V Groun d Pin Assignment s J8 - Infrared connecto r Pi n 1 2 3 4 5 Functio n IRT X GN D IRR X IRR 3 VC C J9 - Fan connecto r[...]

68 J1 3 Pin 1 Pin 2 +5 V Groun d Pin 1 Pin 2 +5 V Signa l Pin 1 Pin 2 +5 V Signa l Pin 1 Pin 2 Signa l Groun d Pin 1 Pin 2 Signa l Groun d Pin 1 Pin 2 Signa l Groun d Pin 1 Pin 2 Pin 3 Pin 4 Signa l N.C . Groun d +5 V Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 +5 V N.C . Groun d Keylock Signa l Groun d HD-LE D (Primary/Secondar y IDE LED ) G-LE D (Green LED ) S[...]