Cisco Systems 15600 manuale d’uso

CH A P T E R 17-1 Cisco ONS 15600 Procedure Guide, R8.0 17 DLPs E100 to E199 Note The terms "Unidirectional Path Swit ched Ring" and "UPSR" may appear in Cisco lit erature. These t erms do not refer to using Cisco ONS 15xxx products in a unidirectio nal path switched ring conf iguratio n. Rather , these terms, as w ell as "[...]

17-2 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E101 Apply a Lock On in a 1+1 Group If the Force switch is successful, CTC sh ows both por ts as [FORCE T O PR OTECT] (or [FORCE TO WORKING]). This indicat ion is sho wn whether or not the ON S 15600 system has been able to mov e traf f ic from one port to the other . If t[...]

17-3 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E102 Apply a Lockout in a 1+1 Group Step 6 Click Ye s in the conf irmatio n dialog box. The lock on has been applied and traf f ic ca nnot be s witched from t hat port. See the “DLP-E168 Clear a Lock On or Lockou t in a 1+1 Protection Group ” task on page 17-53 as need[...]

17-4 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E104 Initiate a Force Switc h to a Path Protection Circuit Step 2 Click the path you wa nt to switch and then cl ick Edit . Step 3 In the Edit Circuit windo w , click the P ath Protection Selectors tab . Step 4 In the Switch State column, click the row fo r the p ath you w[...]

17-5 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E105 Create a DCC Tunnel DLP-E105 Create a DCC Tunnel Note The ONS 15600 can support up to 64 DCC tunnels. T erminated SDCCs cannot be used as a DCC tunnel endpoint, and an SDCC that is used as a DCC tunnel endpo int cannot be terminated. Y ou must delete the terminated SD[...]

17-6 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E106 Clean Fiber Connectors Step 5 In the Destination area, complete the following: • Node—Choose the destination node. • Slot—Choose the destination slot. • Port—Choose the destination p ort. • Channel—Sho wn if you cho se DCC T unnel-D1-D3 as the tunnel t[...]

17-7 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E107 Clean the Fiber Adapters b. Place the connector tip at the top of the slot at a slight angle. In a single stroke, mo v e the connector do wn the wipe without li fting the connecto r from the wipe. Before lifting t he connector from the wipe, straighten the connector .[...]

17-8 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E108 Verify that a 1+1 Working Port is Active d. Remov e and insert the scrub t ool tip se v eral times to clean the f iber adapter . Step 3 T o remov e loose particles from the f iber adapter: a. Remove the dust cap from the rinse tool. Note If the absorb ent pad on t he [...]

17-9 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E109 Drill Holes to Anchor and Provide Access to the Bay Assembly c. Click Ye s in the con fi rmation dialog box. Step 4 V erify that the worki ng slot is carrying traf f ic (W orking/Active). Note If the slot is not acti v e, look for condi tions or alarms that might be p[...]

17-10 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E109 Drill Holes to Anchor and Provide Access to the Bay Assembly Figur e 1 7 -1 Floor T emplate Step 2 Use the corner indicators “C” to determine the closest recommended position of an adja cent 900-mm (35.4-inch) bay assembly . Step 3 Use a marking pen to mark th e [...]

17-11 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E110 Assign a Name to a Port DLP-E110 Assign a Name to a Port Step 1 Double-click the card that has the port you want t o provisio n. Step 2 Click the Pro visioning tab . Step 3 Click the Por t N a m e column for the port number you are assi gning a name to and enter the [...]

17-12 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E112 Provision a Half Circuit So urce and Destination on a BLSR or 1+1 • Re version time—If Re ve rti ve is check ed, click the Re v ersion time f ield and choose a re v ersion time from the drop-do w n list. The range is 0.5 to 12 .0 minutes. The def ault is 5.0 minu[...]

17-13 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E113 Provision a Half Circuit Source and Destination on a Path Protection DLP-E113 Provision a Half Circuit Source and Destination on a Path Protection Step 1 From the Node drop-do wn list, choose the node that will contain th e half circuit. Step 2 From the Slot drop -do[...]

17-14 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E114 Provision Section DCC Terminations DLP-E114 Provision Section DCC Terminations Step 1 In node vie w , click the Pr ovision ing > Comm Channels > SDCC tabs. Step 2 In the SDCC T erminations area, click Create . Step 3 In the Create SDCC T e rminations dialog box[...]

17-15 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E114 Provision Section DCC Terminations Step 8 If you check ed OSI, complete the follo wing st eps. If you checked IP o nly , continue with Step 9 . a. Click Next . b. Provisio n the follo wing fi elds: – Router—Choose the OSI rout er . – ESH—Sets the End System H[...]

17-16 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E115 Change the Se rvice State for a Port DLP-E115 Change the Service State for a Port Step 1 In node vie w , double-click th e card with the port(s) you wa nt to put in or out of serv ice. The card vie w appears. Step 2 Click the Pro visioning > Line tabs. Step 3 In t[...]

17-17 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E116 Remap the K3 Byte Step 8 Return to your ori ginating procedure (NTP). DLP-E116 Remap the K3 Byte Caution If you remap the K3 b yte, remap to the same e xtended b yte (Z2, E2, or F1) on ei ther side of the span. Step 1 In node vie w , double-click the card t hat conne[...]

17-18 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E120 Remove the Narrow CRMs Step 3 From the A uto-refresh drop-do wn list choose one of the follo wing opt ions: • None : This option disab les the auto-refresh feature. • 15 Seconds : This option sets the windo w auto-refresh to 15-secon d time interv als. • 30 Sec[...]

17-19 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E120 Remove the Narrow CRMs Figur e 1 7 -2 Nar r o w CRMs Step 2 Lift the cable rout er slightl y and pull it a way from th e bay . Step 3 Repeat this proc edure for the router on t he other side. Step 4 Unscrew and remo ve the cable radius pieces at the lo wer right and [...]

17-20 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E121 Replace the Existing 600-mm Ki ck Plates with 900-mm Kick Plates DLP-E121 Replace the Existing 600-mm Kick Plates with 900-mm Kick Plates Step 1 Using the screwdri ver , remove the f i ve scre ws located on the 600-mm (23.6- inch) kick plate on the front of the bay .[...]

17-21 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E123 Clear a Manual Switch on a Node Timing Refere nce This operation commands the node to switch t o the refe rence you ha ve selected if the SSM quality of the reference is not lo wer than the current timi ng reference. Step 4 Click the A pply bu tton. Step 5 Click Ye s[...]

17-22 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E124 Set the Optical Po wer Received Nominal Value DLP-E124 Set the Optical Power Received Nominal Value Step 1 In node vie w , double-click the O C-N card that you w ant to pro vision. The card vie w appears. Step 2 Click the Pro visioning > SONET Thr esholds tabs. St[...]

17-23 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E126 Provision the IIOP List ener Port on the CTC Computer • Other Constant—If Port 683 is not used, type the IIOP port specif ied b y your f ire wall ad ministrator . Step 3 Click Apply . Step 4 When the Change Netw ork Conf ig uration message appears, click Ye s . B[...]

17-24 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E127 Edit Path Protectio n Circuit Path Selectors DLP-E127 Edit Path Protection Circuit Path Selectors Step 1 Click the Circ uits tab . Step 2 In the Circuits tab, click th e path protection circuit that you w ant to edit. T o change the settings for multiple circuits, pr[...]

17-25 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E128 Change the Node Name, Date, Time, and Contact Information DLP-E128 Change the Node Name, Date, Time, and Contact Information Note Changing the date, time, or time zone might in validate node perf ormance monitoring counters. Step 1 In node vie w , click the Pr ovisio[...]

17-26 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E129 Enable Dialog Box Do-Not-Display Option DLP-E129 Enable Dialog Box Do-Not-Display Option Note If any user wh o has rights to perform an operation ( f or example, creating a circuit) selects the “Do not sho w this dialog again” check box on a dialo g box, the dial[...]

17-27 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E131 Change Security Policy on Multiple Nodes Step 3 In the User Lockout area, you can modify the following: • Failed Login s Before Lockou t—Choose the number of failed login attempts a user can mak e before the user is lock ed out from the node. Y ou can choose a va[...]

17-28 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E132 Change User Password and Security Levels for a Single Node • Manual Unlock b y Superuser—Check th is box if you w ant to allo w a user with Superuser p ri vile ges to manually unlock a user wh o has been locked out fro m a node. The user wil l remain locked out u[...]

17-29 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E133 Change User and Security Setting s for Multiple Nodes Note User settings t hat you chang ed during thi s task will not appear until that user logs off and logs back in again. Step 5 Return to your ori ginating procedure (NTP). DLP-E133 Change User and Security Settin[...]

17-30 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E135 Log Out a Us er on a Single Node DLP-E135 Log Out a User on a Single Node Step 1 In node vie w , click the Pr ovisioning > Securi ty > Active Logi ns tabs. Step 2 Choose the user you wa nt to log out. Step 3 Click Logout . Step 4 In the Logout User dialog box, [...]

17-31 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E137 Check the Network for Alarms and Conditions Step 7 Click OK . A conf irmation dial og box appears. Step 8 Click OK . Step 9 Return to your ori ginating procedure (NTP). DLP-E137 Check the Network for Alarms and Conditions Step 1 From the V ie w menu, choose Go T o Ne[...]

17-32 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E141 Disable Proxy Service Us ing Netscape (Win dows and UNIX) Note If your computer is running W indo ws XP , you can select Control P anel direct ly from the Start menu. Make sure that you are in Classic V iew before conti nuing with this proced ure. Step 2 In the Contr[...]

17-33 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E142 Install the Narrow CRMs DLP-E142 Install the Narrow CRMs Step 1 On the bottom left and bot tom right, install the cable radi us (2 scre ws). Step 2 Lift the right-si de narro w CRM and align it with the three scre w holes you wil l use to mount the CRM. Step 3 Use a [...]

17-34 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E143 Install the Wide CRMs DLP-E143 Install the Wide CRMs Note If you are installing CRMs o n more than one shelf, it is easiest to install t he lo west CRMs fir st. Note If your site uses under -floor cabling, mou nt the CRMs on the sides of the bay di rectly ne xt to th[...]

17-35 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E143 Install the Wide CRMs Figur e 1 7 -3 CRM Scr ew Holes (F r ont) Step 7 Align the front of the CRM k eyh oles with the scre ws and carefully slide the C RM down so it rests on the screws. T ighten the scre ws, starting with the bottom screw and proceedin g up to the m[...]

17-36 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E144 Use the Reinitialization Tool to Clear the Da tabase and Upload Software (Windows) Step 9 Repeat Steps 5 through 8 for the left-side CRM. Step 10 Return to your ori ginating procedure (NTP). DLP-E144 Use the Reinitialization Tool to Clear the Database and Upload Soft[...]

17-37 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E145 Connect the PDU Ground Cables to the PDU • Acti v ate/Re vert—Check this bo x to acti v ate the uploaded softw are (if the software is a later than the installed v ersion) or re v ert to the uploaded softw a re (if the software is earl ier than the installed vers[...]

17-38 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E145 Connect the PDU Gr ound Cables to the PDU Note A shunt is preinstalled betw een logic and frame grou nd to bond the two grounds. If you are providing a separate logic ground, remove this shunt on both sid es before installing the PDU frame ground. Figure 1 7 -5 Pow e[...]

17-39 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E146 Install Isolated Logic Ground DLP-E146 Install Isolated Logic Ground Step 1 Remov e the PDU safety co v er on the right side. Step 2 Remov e the metal shun t connecting the fr ame ground to the l ogic ground terminals. T erminal designations are marked on the top o f[...]

17-40 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E147 Check BLSR or Path Protection Alarms and Conditions DLP-E147 Check BLSR or Path Pr otection Alarms and Conditions Step 1 From the V iew menu , choose Go to Network V iew . V erify that all BLSR or path protecti on spans on the network map are green. Step 2 Click the [...]

17-41 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E152 Install Public-Key Security Certificate b. In the Set W est Protection Operation dia log box, choose C LEAR from the drop-do wn list. Cl ick OK . c. In the Conf irm BLSR Operation dialo g box, click Ye s . Step 5 T o clear a Force switch on the east line: a. Right-cl[...]

17-42 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E153 Changing the Maximum Number of Session Entries for Alar m History • Ye s —Removes t he modifi ed Jav a po licy f ile from yo ur PC. Choose this option only if you will log into ONS 15600s ru nning Softw are R1.1 or later . • No —Does not remov e the m odif ie[...]

17-43 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E154 Delete Alarm Severity Profiles Step 3 Click Apply and OK . Note Setting the Maximum History Entries v alue to t he high end of t he range uses more CTC memo ry and could impair CTC performance. Note This task changes the maximum history entries reco rded for CTC sess[...]

17-44 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E155 Enable Alarm Filtering Step 9 T o remo ve the alar m profi le from the Prov isioning > Alarm Prof iles > Alarm Prof ile Editor windo w , right-click the column o f the prof ile you d eleted and choose Remo ve fro m the shortcut menu. Note If a node and prof ile[...]

17-45 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E155 Enable Alarm Filtering Figur e 1 7 -7 Conditio ns Window Filt er Dialog Bo x Step 3 In the Sho w Se verity area, alarm se v erities appear . All of the applicable se verities are checked b y def ault. If a se v erity is chec ked, it ap pears in the alarm list . Note [...]

17-46 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E156 Modify Alarm and Condition Filtering Parameters DLP-E156 Modify Alarm and Condition Filtering Parameters Step 1 In the node, network , or card vie w , click the Alarms tab . Step 2 Click the Filter button at the lo wer -left of the bottom too lbar . The Alarm Filter [...]

17-47 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E157 Disable Alarm Filtering DLP-E157 Disable Alarm Filtering Step 1 In the node, network , or card vie w , click the Alarms tab . Step 2 Click the Filter tool at the lo wer -ri ght side of the bottom to olbar . Alarm filt ering is enabled if the t ool is selected and dis[...]

17-48 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E159 Manually Lock or Un lock a User on Multiple Nodes Step 6 Click OK . Step 7 Return to your ori ginating procedure (NTP). DLP-E159 Manually Lock or Unl ock a User on Multiple Nodes Step 1 From the V iew menu, chose Go T o Network V iew . Step 2 Click the Pro visioning [...]

17-49 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E160 Verify BLSR Extension Byte Mapping DLP-E160 Verify BLSR Extension Byte Mapping Step 1 In network vie w , double-click one of t he BLSR nodes with OC-N trunk cards t h at will be reconnected after a BLSR node remov al. Step 2 Double-click one OC-N BLSR trunk card to o[...]

17-50 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E161 Single Shelf Control Card Switch Test d. In node vie w , click the Maintenance > Pr eferr ed Copy tabs. e. From the Set Preferred d rop-down list, choose Copy B . Click Apply . f. Remov e the SSXC card from Slot 8. (The SSX C card faceplate e xtends to cover Slot [...]

17-51 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E163 Delete Circuits DLP-E163 Delete Circuits Step 1 Complete the “NTP-E69 Back Up th e Database” proced ure on page 14-4 . Step 2 In v estigate all network alarms and resolv e any problems that could be af fected by the circuit deletion. If necessary , refer to the C[...]

17-52 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E165 Change an OC-N Card Step 10 Complete the “NTP-E69 Back Up th e Database” proced ure on page 14-4 , if ne eded. Note If a schedule is established for database backup, you do not need to complet e a backup after e very circuit add ition and delet ion. Step 11 Retur[...]

17-53 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E167 Clear a Manual or Force Switch in a 1+ 1 Protection Group Step 6 Complete the “NTP-E11 Install the OC-N Cards” procedure on page 2-4 . Step 7 Return to your ori ginating procedure (NTP). DLP-E167 Clear a Manual or Force Switch in a 1+1 Protection Group Step 1 In [...]

17-54 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E169 Initiate a Lockou t on a Path Protection Path Step 2 In the Protection Groups ar ea, choose the protection grou p that contai ns the card you w ant to clear . Step 3 In the Selected Group area, choo se the card you want to clear . Step 4 In the Inhibit Switching area[...]

17-55 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E170 Clear a Switch or Lockout o n a Path Protection Circuit DLP-E170 Clear a Switch or Lockout on a Path Protection Circuit Step 1 Click the Circ uits > Cir cuits tabs. Step 2 Click the path you want to switch and click Edit . Step 3 In the Edit Circuit windo w , clic[...]

17-56 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E171 Verify Fan Operation Figure 17 -8 ONS 15600 Shelf with One Fa n T ra y and Air Filt er Remov ed Step 2 T o ensure the three front fa ns are op erating, carefully place your hand in the card cage two to three inches (50 to 76 mm) from the top o f the cage, palm up, to[...]

17-57 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E172 Install Fiber-Optic Cables for Path Protection Configurations DLP-E172 Install Fiber-Optic Cables for Path Protection Configurations Caution T o a void lo ss of traff i c, do not create a path protec tion usi ng two por ts on the same card. Y ou can create a path pro[...]

17-58 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E176 Edit Path Protection Dual-Ri ng Interconnect Circ uit Hold-Off Timer DLP-E176 Edit Path Protection Dual-Ri ng Interconnect Circuit Hold-Off Timer Note Cisco recommends that you set the DRI port HO T v alue to zero and the circuit pa th selector HO T v alue to a numbe[...]

17-59 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E177 Change Tunnel Type DLP-E177 Change Tunnel Type Step 1 From the V ie w menu, choose Go to Network V iew . Step 2 Click the Pro visioning > Overhead Cir cuits tabs. Step 3 Click the circuit tunnel that y ou want to con vert. Step 4 Click Edit . Step 5 In the Edit Ci[...]

17-60 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E179 Repair an IP Tunnel Step 1 From the V ie w menu, choose Go to Network V iew . Step 2 Click the Pro visioning > Overhead Cir cuits tabs. Step 3 Click the ov erhead circuit th at you wa nt to delete. Step 4 Click Delete . Step 5 In the conf irmation dial og box, cli[...]

17-61 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E180 Provision Path Trace on Circuit Source and De stination Ports DLP-E180 Provision Path Trace on Ci rcuit Source and Destination Ports Note This task assumes you are sett ing up path trace on a bidirectional circuit and setting up transmit strings at the circuit source[...]

17-62 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E180 Provision Path Trace on Ci rcuit Source and Destination Ports Figur e 1 7 -9 Selecting the Edit P ath T race Option b. In the New T ransmit String field , enter the circu it source transmit string. Enter a stri ng that makes the source port easy to identify , such as[...]

17-63 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E180 Provision Path Trace on Circuit Source and De stination Ports c. Click the Disable AIS and RDI if T IM-P is detected check box if you want to suppress the alarm indication si gnal (AIS) an d remote defect ind i cation (RDI) when the STS Path T race Identif ier Mismat[...]

17-64 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E181 Provision Path Trace on OC-N Ports The expect and receive strings are updated every fe w s econds if the Path T race Mo de f ield is set to Auto or Manual. Step 11 Click Close . The detailed circuit window indicates path trace with an M (manual path trace) or an A (a[...]

17-65 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E18 2 Create Logi n Node Gro ups Step 7 If you set the Path T race Mode f ield to Manual, enter the string that the OC-N port should recei ve in the Ne w Expected String f ield. T o do this, trace the circ uit path on the detail ed circuit w indow to determine whether the[...]

17-66 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E183 Delete a Node from t he Current Session or Login Group Figur e 1 7 -1 0 Login Node Gr oup Step 8 Return to your ori ginating procedure (NTP). DLP-E183 Delete a Node from t he Current Session or Login Group Step 1 From the V ie w menu, choose Go to Network V iew . Ste[...]

17-67 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E184 Configure the CTC Alerts Dialog Box for Automatic Popup DLP-E184 Configure the CTC Alerts Dialog Box for Automatic Popup Step 1 Click the CTC Alerts toolbar icon. Step 2 In the CTC Alerts dialog box, choose o ne of the follo wing: • All alerts —Sets the CTC Alert[...]

17-68 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E186 Remove Pa ss-through Connections Step 6 From the File menu, choose Exit . Step 7 In the conf irmation dial og box, click Ye s . Step 8 Return to your ori ginating procedure (NTP). DLP-E186 Remove Pass-through Connections Step 1 Log into the deleted node. Step 2 In th[...]

17-69 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E187 Delete a Node from a Specified Login Node Group DLP-E187 Delete a Node from a Specified Login Node Group Step 1 From the CTC Edit menu, choose Pr efer ences . Step 2 In the Preferences dialog box, click the Login Node Groups tab . Step 3 Click the login node group t [...]

17-70 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E189 Provision Line DCC Terminations • OOS,MT—Puts the circuit cross-connects in the OO S-MA,MT service state. This se rvice state does not interrupt traf fic flo w and allo ws loopb acks to be performed on the circuit, but suppresses alarms and conditions. Use the OO[...]

17-71 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E189 Provision Line DCC Terminations Note User can provision SDCCs an d LDCCs (Line DCC) on dif ferent ports . User can pro vision the SONET Line DCCs and SDCCs (when not used as a DCC termi nation by the ON S 15600) as DCC tunnels. See the “DLP-E105 Create a DCC T unne[...]

17-72 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E190 Provision a Proxy Tunnel – IIH—Sets the Intermediate System to In termed iate System Hello PDU propa gation frequency . The IS-IS Hello PDUs establish and maintain adj acencies between ISs. The default is 3 seconds. The range is 1 to 600 seconds. – IS-IS Cost?[...]

17-73 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E191 Provision a Firewall Tunnel Step 5 Continue with your originating pro cedure (NTP). DLP-E191 Provision a Firewall Tunnel Note If the proxy serv er is conf igured as proxy-o nly or is disabled, you canno t set up a f ire wall tunn el. Step 1 Click the Pro visioning &g[...]

17-74 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E192 Delete a Proxy Tunnel DLP-E192 Delete a Proxy Tunnel Step 1 Click the Pro visioning > Network > Proxy su btabs. Step 2 Click the proxy tunnel that you w ant to delete. Step 3 Click Delete . Step 4 Continue with your originating pro cedure (NTP). DLP-E193 Delete[...]

17-75 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E196 Change a Section DCC Termination DLP-E196 Change a Section DCC Termination Step 1 Click the Pro visioning > Comm Channels > SDCC tabs. Step 2 Click the SDCC that you want to change. Step 3 Click Edit . Step 4 In the SDCC T ermination Editor di alog box, complet[...]

17-76 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E198 Delete a Section DCC Termination • Far End i s Foreign— Check this box to specify that the LDCC termination is a no n-ONS node. • Far end IP—If you checked the Far End is Foreign ch eck box, type the IP address of the f ar-end node or lea ve the 0 .0.0.0 defa[...]

17-77 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E199 Delete a Line DCC Termination Step 4 Return to your ori ginating procedure (NTP).[...]

17-78 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E199 Delete a Line DCC Termination[...]