LG Electronics L227WT manuale d’uso

M ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. S ee the label attached on the product and give the information to your dealer when you ask for service. User ’ s Guide L227WT L227WTG L227WTP[...]

A1 This unit has been engineered and manufactur ed to ensure your personal safety , however impr oper use may result in potential electrical shock or fir e hazards. In order to allow the proper operation of all safeguards incorporated in this display , observe the following basic rules for its installation, use, and servicing. On Safety Use only th[...]

A2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventil[...]

A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before setting up the monitor, ensure that the power to the monitor, t[...]

A4 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on a flat surface. 4. Nip Latch inside, Take off the stand base from stand body. 5. Please pull the stand body lightly to separate it from the hinge body. 2. Place the monitor face down on the cushion or soft cloth. 3. Slide the Cable Deco Cover out from the stand body[...]

A5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~20˚ Ergonomic It is recommended that in order to maintain an ergonomic and c[...]

A6 Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form to . 1 3. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) NOTE ‘ Self Image Setting Function’?[...]

A7 Control Panel Functions ZOOMING At the current display, Use 'ez Zooming' Key, then the display resolution is transferred to the one step low resolution. Use 'ez Zooming' Key one more, the display is back to the original display. *Only One touch of ez-zoom, you can fine the best resolution you want and it is possible to magnif[...]

A8 Control Panel Functions This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off. Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO [...]

A9 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Scr een Display Control system. A short example is given below to familiarize you with the use of the contr ols. The following section is an outline of the available adj[...]

A10 NOTE The order of icons may differ depending on the model (A10~A15). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Scr een Display control, adjustment, and setting menus. To adjust the brightness, contrast and gamma of the screen PICTURE COLOR POSITION TRACKING SETUP Main menu Sub-menu A D Reference PR[...]

A11 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Y ou were intr oduced to the procedur e of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU B[...]

A12 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. PICTURE PICTURE PR[...]

A13 MENU : Exit : Decrease : Increase SET : Select another sub-menu On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows you to r[...]

A14 On Screen Display(OSD) Selection and Adjustment Press the button to reset immediately. If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled only when the input signal is an analog signal. SETUP To choose the language in which the co[...]

A15 On Screen Display(OSD) Selection and Adjustment Icons Menu Name Sub-menu Name Main menu Sub menu Description To adjust the USER sub-menu function, Press the SET Button MOVIE TEXT NORMAL USER When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen wi[...]

A16 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue or green? ● Is the power indicator amber? ● Do you[...]

A17 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results [...]

A18 T roubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driv[...]

A19 Specifications Display Sync Input Video Input Resolution Plug&Play Power Consumption (without speaker) Dimensions &Weight Tilt Range Swivel Range Power Input Environmental Conditions Stand Base Power cord 22 inches (55.8 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 22 inches viewable 0.282*0.282 mm pixel pitch Horizontal Freq[...]

A20 Specifications Preset Modes (Resolution) *Recommend Mode Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 2 3 4 5 6 7 8 9 10 11 *12 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1680 x 1050 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.9[...]

A21 Installing the W all mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. Kensington Security Slot Connected to a locking cable that can be purchased separately[...]

Digitally yours[...]