Texas Instruments CC2511 manuale d’uso

CC2511 Dongle CC2511 Dongle User Manual Rev. 1.0 SWRU082 Page 1 of 24[...]

CC2511 Dongle Table of contents 1 INTRODUCTION ...................................................................................................................... 3 2 ABOUT THIS MA NUAL .......................................................................................................... 3 3 DEFINITIONS ......................................[...]

CC2511 Dongle 1 Introduction Thank you for purchasing a SmartRF ® 04DK Development Kit. Please note that Chipcon uses th e term SmartRF ® 04DK as a collective term for all development kits on the SmartRF ® 04 platform. This development platform supp orts evaluation, development and prototyping using the SmartRF ® 04 products from Chipcon. Make [...]

CC2511 Dongle 4 Connecting CC2511 Dongle to SmartRF04EB. Please see the “CC2430DK_CC2 510_CC1110_User_Manu al” for more information on th e SmartRF04EB and how to use the CC25 10EM. Make sure to inst all SmartRF ® Studio before connecting the SmartRF04 EB to a PC. SmartRF ® Studio can be downloaded from the www. chipcon.com or www.ti.com/lpw [...]

CC2511 Dongle Figure 1 CC2511 Dongle powered from USB cable Figure 2 CC2511 Dongle powered from SmartRF0 4EB 6. Turn on the power on the SmartRF04EB. See Figure 3. Figure 3: SmartRF04EB Po wer switch, power on. The CC2511 can now be programme d with the Chipcon Flash Programmer software. Th e firmware on the CC2511 can al so be debugge d using the [...]

CC2511 Dongle 5 Using SmartRF04EB as an In-Circuit Emulator (ICE) The SmartRF04EB can be used as ICE f or the CC2511 To use the SmartRF04EB as I CE, the IAR Embedded Workbe nch software must be in stalled. The Embedded Workbench is a C-Co mpiler, Simulator, and ICE debugger. See the IAR Embedded Workbench documentation supplied with the kit for ins[...]

CC2511 Dongle 1 2 Figure 4: Recommended debug connector lay out (Top vie w) Figure 4 shows the required sig nal for a minimum connector layout. Figure 5: SmartRF04EB debug connector for deb ugging CC2511 Dongle / other external targ et systems 5.1 Debugging USB firmware When writing and debuggi ng USB firmware one should remember that when Windows [...]

CC2511 Dongle 5.2 Known problems When using the deb ug interface through the leve l-co nverter on the SmartRf04EB. (Shown in Figure 1 and Figure 2) it might become unstable. This problem is more li kely to occur a low voltages or with crosstalk in the cable at high interface speed. First make sure that the 10 pin flat cable used to connect the CC25[...]

CC2511 Dongle 6 CC2511 application examples This section describes the application examples avail able for the CC2511. Th ese application examples focus on how to use the USB on the CC2511. The examples is available both a s source code and ready-to - uploa d .hex files from the Chipcon web site . There are three CC2511 application examples. • Wi[...]

CC2511 Dongle 6.1 Wireless mouse / practical joke This application demonstrates the use of the CC2511Dongle a s a USB composite HID (Human Interface Device), with both keyboard and m ouse. The application will work on most operat ing systems. This application example uses the USB framework found in the CC2511 firmware lib rary to setup the USB on t[...]

CC2511 Dongle 6.2 Wireless USB to Serial port conv erter This application example is a wireless USB to serial port (RS232 ) converter. It creates a virtual serial port in Windows. Data sent to this virt ual serial port will be sent to the CC2511 Dongle over USB , then to CC2510 EM over radio and fina lly out on the seri al port on the CC2510 EM / S[...]

CC2511 Dongle When Windows have finished i nstalling the device, a new se rial port will appea r in the device manager in Windows. See Figure 9. Figure 9: Virtual serial port in Windows Devi ce manager The Windows driver will only work if the “Ti Wi reless USB to Serial” is assigned to COM1 to COM9. (In Figure 9 it is assigned to CO M6) If ther[...]

CC2511 Dongle 6.3 Wireless WinAmp remote contr ol This application example is a wi reless remote control for WinAmp media playe r. It is a two- way remote, which display the song info rmati on of the song played on the LCD screen on the SmartRF04EB. The communication betwe en the CC2511 Dongle and Wi nAmp is handled by a custom WinAmp plug-in. Henc[...]

CC2511 Dongle 8. If windows ask for the file “cudal.sys” o r “cudal98.sys”, point to “cud al.sys” or “cudal98.sys”. 9. Turn on the CC2510EM / SmartRF04EB. 10. The USB dongle may ha ve to be removed and reinserted once to the PC for the application to work. 6.3.3 Running the application 1. Start WinAmp, the gen_chipcon_remote plug-in[...]

CC2511 Dongle 7 USB development framework A versatile, efficient and easy to use USB development framework is available for the CC2511. The intension wit h this framework is to make USB development as q uick and easy as possible. The framewo rk includes a firmware fram ework for the embedded so ftware on the CC2511, and a Windows USB driver framewo[...]

CC2511 Dongle As shown in Figure 10 the USB library is divided into five modules: The USB Framew ork (usbfw ) contains all USB status i nformation and functions fo r initialization, device reset handling, and transfe rs on endpoint 0. It also contains basi c macros and functions for endpoint control and F IFO access. Vendor and class re quests are [...]

CC2511 Dongle The complete do cumentation of the CUDAL fram ework is available in a compressed HT ML file, “cudal.chm”, found in “C C2511DKpc_swCUDAL doc” 7.2.1 Windows USB driver licen se The Windows USB driver framework CUDAL is based on the USBIO driver from Thesycon. This driver is not free and requires a lice nce. Texas Instruments [...]

CC2511 Dongle 8 CC2511 Dongle hardware description Debug connecto r Line marking cutaway sect ion of the dongle PCB antenna CC2511 USB connecto r Button LED GPIO testpins Figure 11: CC2511 Dongl e top v iew Alternative debug connecto r Figure 12: CC2511 Dongl e back v iew 8.1 User Interface The CC2511 Dongle has one button an d one LED th at can be[...]

CC2511 Dongle 8.3 Debug connector The CC2511 Dongle has debug conn ector (P3) that is compatible with th e SoC debug connector on the SmartRF04EB. This enables the CC2511 Don gle to be programmed and debugged via the SmartRF04EB. The debug con nector and the test pins on the CC25 11 Dongle can be removed to redu ce its size. If that is done, progra[...]

CC2511 Dongle 9 CC2511 Dongle schematics Figure 13: CC2511 Dongl e schema tic, page 1 SWRU082 Page 20 of 24[...]

CC2511 Dongle Figure 14 CC2511 Dongle schema tic, page 2 SWRU082 Page 21 of 24[...]

CC2511 Dongle Figure 15 CC2511 Dongle schema tic, page 3 SWRU082 Page 22 of 24[...]

CC2511 Dongle Figure 16 CC2511 Dongle schema tic, page 4 SWRU082 Page 23 of 24[...]

CC2511 Dongle 10 Document history Revision Date Description/Changes 1.0 2006-07-06 Initial release SWRU082 Page 24 of 24[...]