Zanussi ZGF 782 CTX manuale d’uso

GAS HOB ZGF 782 CTN ZGF 782 CTX INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB IE[...]

2 Import ant Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Inst allation z This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions an[...]

3 For the User Content s For the Inst aller Important Safety Information 2 Description of the Hob 4 Operation 5 Maintenance and Cleaning 6 Something Not Working? 7 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V oltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive)[...]

4 1. Auxiliary Burner 2. Semi-rapid Burners 3. Ultra-rapid Triple-crown Burner 4. Rapid Burner 5. Control knobs Description of the Hob 2 1 4 3 2 5[...]

5 Operation Hob burners T o light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (Fig. 1, D) to be heated and the safety device to be switched off, otherwise the gas supp[...]

6 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water t[...]

7 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre. SYMPTOM  There is no spark when lighting the gas  The gas ring burns unevenly SOLUTION  Check that the unit is plugged in and the electrical supply is switched on  Check that th[...]

8 OVERALL DIMENSIONS Width: 680 mm Depth: 510 mm CUT OUT DIMENSIONS Width: 560 mm Depth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz supply , 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Fron[...]

9 FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 400 mm 100 mm 55 mm 50 mm 50 mm 600 mm 700 mm 400 mm 400 mm 100 mm 55 mm 600 mm 50 mm 50 mm FO 2369* FO 2231* Import ant safety requirement s This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Cu[...]

10 Inst allation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability , should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INS[...]

11 FO 2564 FO 2044 3 Dimensions are given in mm. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown [...]

12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 5[...]

13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all[...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

15 Commissioning When the hob has been fully inst alled it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas t ap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguis[...]

16 Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option rep air or replace the same FREE OF CHARGE for la[...]

17 This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: ?[...]

18[...]

19[...]

Grafiche MDM - Forlì 35687-7802 1 1/06 www .zanussi-electrolux.co.uk[...]