English dropdown-ico

Bosch TS2000 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Bosch TS2000, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Bosch TS2000 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Bosch TS2000. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Bosch TS2000 should contain:
- informations concerning technical data of Bosch TS2000
- name of the manufacturer and a year of construction of the Bosch TS2000 item
- rules of operation, control and maintenance of the Bosch TS2000 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Bosch TS2000 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Bosch TS2000, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Bosch service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Bosch TS2000.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Bosch TS2000 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    IMPOR T ANT : IMPOR T ANT : IMPOR T ANTE: Read Before Using Lire avant usage Leer antes de usar Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad TS2000 For English Parlez-vous français? ¿Habla español? See page 2 Voir page 9 Ver página 16 1-877-BOSCH99 (1-877-267-2499) www .boschto[...]

  • Page 2

    TS2000 TABLE SAW STAND PACKAGE CONTENTS: Item Qty. Part Description A (1) Upper Cross Bar B (1) Lower Cross Bar C (1) Kickback Bar D (1) Right Leg/Wheel Assembly E (1) Left Leg/Wheel Assembly F (1) Table Top You have purchased a Bosch Table Saw Stand TS2000. Designed for job site use. This unit sets up and folds quickly, and is easily loaded or unl[...]

  • Page 3

    -3- *Note: There are two (2) 8mm x 50mm Phillips head screws and two (2) 8mm lock nuts to be used only when attaching other branded table saws to the Bosch TS2000 stand. See page 6 for instructions. STAND ASSEMBLY HARDWARE (packaged in one bag) Item Qty. Part Description G 6 10mm x 100mm Hex Head Bolts H 2 10mm x 50 mm Hex Head Bolts I 6 8mm x 50 m[...]

  • Page 4

    Step 1 Attach Upper and Lower Cross Bars 1. Position lower cross bar on a flat surface as shown in figure A. 2 . Insert ends of upper cross bar into the lower cross bar and push downward as far as it will go. 3. Insert four (4) 8 mm x 50 mm Phillips Head Screws through the holes of the upper and lower cross bars, and securely tighten with four (4) [...]

  • Page 5

    Step 4 Attach Table Top 1. Locate the table top and position holes in end of table top with holes in upper cross bar as shown in figure D. 2. Place one (1) flat washer onto one (1) 10 mm x 100 mm bolt. 3 . Insert bolt through table top and place another (1) flat washer on bolt between table top and upper cross bar. 4. Insert bolt through upper cros[...]

  • Page 6

    For Mounting Bosch 4000 Table Saw to Stand 1. Using the diagram below, locate the Bosch 4000 mounting holes and position saw on stand as shown in figure F. 2. Place one (1) 6 mm flat washer onto one (1) 6 mm x 75 mm hex head bolt and insert bolt through mounting hole in table saw and through stand table top. 3 . Place one (1) 6 mm flat washer and s[...]

  • Page 7

    Operating Instructions -7- Fold Stand Upright Keep fingers clear of hinge points when folding or unfolding the stand. 1. Slightly lift stand by the black handle. 2. Rotate release lever down to clear locking pins. 3. With both hands on the handle, pull up and push forward on the stand, figure B, until it locks in the upright position, figure C. Low[...]

  • Page 8

    To level stand The stand is equipped with two adjustable feet for leveling the stand. To adjust: loosen wing nut and adjust the height of the foot by screwing the threaded shaft clockwise to raise foot or counter- clockwise to lower foot. Retighten wing nut securely. To reduce the risk of injury, periodically check that all fasteners are attached a[...]

  • Page 9

    Veuillez lire et bien comprendre tout le mode d’emploi. Le fait de ne pas respecter la totalité des instructions contenues dans ce mode d’emploi peut résulter en des blessures graves. Assemblez et serrez complètement tous les dispositifs de fixation nécessaires au montage de cette plateforme de support. Souvenez-vous également d’inspecte[...]

  • Page 10

    -10- ÉLÉMENTS DE QUINCAILLERIE POUR L’ASSEMBLAGE DE LA PLATEFORME DE SUPPORT (contenus dans un seul sac) Article Qté. Description de la pièce G (6) Boulons à tête hexagonale (10 mm x 100 mm) H (2) Boulons à tête hexagonale (10 mm x 50 mm) I (6) Vis à tête cruciforme Phillips (8 mm x 50 mm)* J (18) Rondelles plates de 10 mm K (2) Rondell[...]

  • Page 11

    Étape 2 Fixation des ensembles de pied/roue 1. Localisez l’ensemble de pied/roue de droite et placez-le sur le côté droit de l’ensemble de barre transversale supérieure/ barre transversale inférieure, tel que cela est illustré à la figure B. 2. Placez une (1) rondelle plate sur un (1) boulon de 10 mm x 100 mm et insérez-les dans l’ens[...]

  • Page 12

    Étape 4 Fixation du plateau de table 1. Localisez le plateau de table et alignez les trous dans l’extrémité du plateau de table avec les trous de la barre transversale supérieure, tel que cela est illustré à la figure D. 2. Placez une (1) rondelle plate sur un (1) boulon de 10 mm x 100 mm. 3. Insérez le boulon à travers le plateau de tabl[...]

  • Page 13

    Pour le montage de la scie à table Bosch 4000 sur la plateforme de support 1. En vous servant du diagramme ci-dessous, localisez les trous de montage sur la scie Bosch 4000 et positionnez cette dernière sur la plateforme de montage tel que cela est illustré à la figure F. 2. Placez une (1) rondelle plate de 6 mm sur un (1) boulon à tête hexag[...]

  • Page 14

    Pliage de la plateforme de support dans la position verticale Gardez vos doigts à distance des points d’articulation quand vous pliez ou dépliez la plateforme de support. 1. Soulevez légèrement la plateforme par la poignée noire. 2. Déplacez le levier de libération vers le bas en le faisant tourner pour dégager les goupilles de verrouilla[...]

  • Page 15

    -15- Mise de niveau de plateforme de support La plateforme de support est munie de deux pieds de nivellement réglables. Réglage : desserrez l'écrou à oreilles et ajustez la hauteur du pied en vissant la tige filetée dans le sens des aiguilles d'une montre pour relever le pied ou dans le sens inverse des aiguilles d'une montre po[...]

  • Page 16

    Lea y entienda todas las instrucciones. Si no se siguen todas las instrucciones que aparecen a continuación, el resultado podría ser lesiones corporales graves. Ensamble y apriete completamente todos los elementos de sujeción requeridos para esta base de soporte. Recuerde también comprobar ocasionalmente la base de soporte y asegurarse de que s[...]

  • Page 17

    -17- HERRAJES DE ENSAMBLAJE DE LA BASE DE SOPORTE (empacados en una bolsa) Artículo Cant. Descripción de la pieza G (6) Pernos de cabeza hexagonal de 10 mm x 100 mm H (2) Pernos de cabeza hexagonal de 10 mm x 50 mm I (6) Pernos de cabeza Phillips de 8 mm x 50 mm* J (18) Arandelas planas de 10 mm K (2) Arandela de estrella de 10 mm L (6) Tuercas d[...]

  • Page 18

    -18- Ensamblaje Paso 1 Acople las barras transversales superior e inferior 1. Posicione la barra transversal inferior sobre una superficie plana de la manera que se muestra en la figura A. 2. Introduzca los extremos de la barra transversal superior en la barra transversal inferior y empuje hacia abajo la barra superior para que los extremos entren [...]

  • Page 19

    -19- Paso 4 Coloque el tablero de la mesa 1. Localice el tablero de la mesa y posicione los agujeros ubicados en el extremo del tablero de la mesa de modo que coincidan con los agujeros ubicados en la barra transversal superior, de la manera que se muestra en la figura D. 2. Coloque una (1) arandela plana en un (1) perno de 10 mm x 100 mm. 3. Intro[...]

  • Page 20

    Para montar la sierra de mesa Bosch 4000 en la base de soporte 1. Utilizando el diagrama que se muestra más adelante, localice los agujeros de montaje de la sierra de mesa Bosch 4000 y posicione la sierra sobre la base de soporte de la manera que se muestra en la figura F. 2. Coloque una (1) arandela plana de 6 mm en un (1) perno de cabeza hexagon[...]

  • Page 21

    Pliegue la base de soporte en posición vertical Mantenga los dedos alejados de los puntos de bisagra cuando pliegue o despliegue la base de soporte. 1 . Levante ligeramente la base de soporte por el mango negro. 2. Gire la palanca de liberación hacia abajo para que no toque los pasadores de fijación. 3 . Ahora, con las dos manos en el asa, tire [...]

  • Page 22

    -22- Para nivelar la base de soporte La base de soporte está equipada con dos pies ajustables para nivelarla. Para ajustar los pies: Afloje la tuerca de fijación y ajuste la altura del pie enroscándolo en el sentido de las agujas del reloj para subirlo y en sentido contrario al de las agujas del reloj para bajarlo. Reapriete firmemente la tuerca[...]

  • Page 23

    -23-[...]

  • Page 24

    2 610 923 971 10/04 Printed in Taiwan LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from defects in material or workmanship for a period of one year from date of purchase. SELLER’S SOLE [...]