English dropdown-ico

Bunn H5EA PC manual

1
2
3
4
5
6
7
8
9
10
11

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Bunn H5EA PC, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Bunn H5EA PC one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Bunn H5EA PC. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Bunn H5EA PC should contain:
- informations concerning technical data of Bunn H5EA PC
- name of the manufacturer and a year of construction of the Bunn H5EA PC item
- rules of operation, control and maintenance of the Bunn H5EA PC item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Bunn H5EA PC alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Bunn H5EA PC, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Bunn service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Bunn H5EA PC.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Bunn H5EA PC item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    H5E-DV PC H5EA PC INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-[...]

  • Page 2

    2 39338 012609 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years part[...]

  • Page 3

    3 INTRODUCTION This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel above the dispense valve that indicates the status of the dispenser . This equipment is for indoor use, either wall-mounted or on a sturdy counter or shelf. ! WA RNING Ve ry Hot W ater Use With Care! 12593.0000 00831.0000 37881.0000 [...]

  • Page 4

    4 ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power sour ce until specified in Initial Set-Up. Refer to Data Plate on the Brewer , and local/national electrical codes to determine circuit requirements. Electrical Hook-Up CAUTION – Improper electrical installation will damage electronic com- ponents. 1. An electr[...]

  • Page 5

    5 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WA TER system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1 ⁄ 2 " or larger supply line. A shut-off valve should be installed in the line before the dis- penser . Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to redu[...]

  • Page 6

    6 INITIAL SET -UP CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the upper panel from the rear of the dispenser . 2. Make sure the toggle switch below the circuit board is set to the desired voltage (120 volts or 208/240 volts) and the red switc[...]

  • Page 7

    7 OPERA TING CONTROLS (a) VOLUME SELECTOR BUTTONS Press and release the button corresponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress. (b) AUTO STOP/MANUAL DISPENSE BUTTON Press and release button [...]

  • Page 8

    8 PROGRAMMING When power is applied to the dispenser , the display located on the bottom of the main circuit board will show the revision level of the software for 5 seconds, and then go to (-). While the tank is filling, the display will read (FIL). When the tank is full the display will return to (-). LEVEL 1 PROGRAMMING T ANK WA TER TEMPERA TUR[...]

  • Page 9

    9 3. Press and release the center button once more. The display will read H2 , then show either F AH (Degrees in Fahrenheit) or Cen (Degrees in Centigrade). 4. Press and release the (+) or (-) buttons to alternate between F AH and CEn . 5. T o Exit Level 2 Programming, press and release the Center Button twice more. The Display will show the Softwa[...]

  • Page 10

    10 WIRING DIAGRAMS J7-4 J7-1 L1 J2-10 MAIN CONTROL BOARD J2-1 J2-5 N.O. COM J4-1 J6-1 J1-11 J1-5 J1-1 PINK-22 J5-1 J5-3 GRN-18 BLK WHI J3-5 J3-8 J3-1 WHT -14 WHT -18 WHT -18 WHT -18 1800 W T ANK HEA TER GRN RED-14 BRN-14 WHI/VIO-14 VIO-18 BLK-18 WHI/BLU-18 WHI-18 4000 W T ANK HEA TER L2 N MASTER ON/OFF SWITCH BLK-14 RED-14 SCHEMA TIC WIRING DIAGRAM[...]

  • Page 11

    11 WIRING DIAGRAMS 39338 040309 J7-4 J7-1 L1 J2-1 MAIN CONTROL BOARD J2-10 J2-5 N.O. COM J4-1 J6-1 J1-11 J1-5 J1-1 PINK-22 J5-3 J5-1 GRN-18 BLK WHI J3-5 J3-1 J3-8 RED-18 RED-18 GRN/YEL RED-14 RED-14 VIO-18 BLK-18 WHI/BLU-18 WHI-18 4000 W T ANK HEA TER L2 EMI FIL TER BLK-14 RED-14 SCHEMA TIC WIRING DIAGRAM H5E A PC CE BLU-14 BLU-14 BLK-14 LIMIT THER[...]