English dropdown-ico

Cisco Systems 78-12510-02 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Cisco Systems 78-12510-02, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Cisco Systems 78-12510-02 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Cisco Systems 78-12510-02. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Cisco Systems 78-12510-02 should contain:
- informations concerning technical data of Cisco Systems 78-12510-02
- name of the manufacturer and a year of construction of the Cisco Systems 78-12510-02 item
- rules of operation, control and maintenance of the Cisco Systems 78-12510-02 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Cisco Systems 78-12510-02 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Cisco Systems 78-12510-02, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Cisco Systems service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Cisco Systems 78-12510-02.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Cisco Systems 78-12510-02 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    CHAPTER 5-1 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 5 Configuring the MGX RPM-PR This chapter describes how to complete a basic conf iguration of the MGX Route Processor Module (RPM-PR). It provides procedures for conf iguring A TM, Ethernet, and F [...]

  • Page 2

    5-2 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR T o connect a modem to the auxiliary port on the RPM-PR, see Chapter 3, “Installing the MGX RPM-PR. ” Booting the RPM-PR When the RPM-PR is boote[...]

  • Page 3

    5-3 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR RPM-PR Bootflash Precautions The RPM-PR bootf lash is used to store boot image, conf iguration and “run time” f iles. The Flash stores and access[...]

  • Page 4

    5-4 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR drwxrwxrwx 1 0 0 13312 May 11 15:47 ./ drwxrwxrwx 1 0 0 13312 May 11 17:10 ../ -rwxrwxrwx 1 0 0 2253552 May 11 15:47 mpsm_t1e1_030.000.004.016-P2.fw [...]

  • Page 5

    5-5 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Step 1 Enter show ip int brief to display your router IP interfaces. Router# show ip int brief Interface IP-Address OK? Method Status Protocol Switch[...]

  • Page 6

    5-6 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR switch autoSynch off ! ip kerberos source-interface any ip classless no ip http server ! ! ! line con 0 transport input none line aux 0 line vty 0 4 [...]

  • Page 7

    5-7 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Step 6 Enter show run to vie w your conf iguration. The conf iguration is similar to the one shown here. Router# show run Building configuration... C[...]

  • Page 8

    5-8 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Back Card Bay and Interface Port Numbers This section describes ho w to identify the back card bay and interface port numbers on the RPM-PR for all b[...]

  • Page 9

    5-9 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Router(config)# interface fastEthernet 1/1 Step 3 Y ou can assign an IP address and subnet mask to the interface with the ip addr ess conf iguration [...]

  • Page 10

    5-10 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR 0 input packets with dribble condition detected 5 packets output, 300 bytes, 0 underruns(0/0/0) 5 output errors, 0 collisions, 0 interface resets 0 [...]

  • Page 11

    5-11 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Router# config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# interface fastethernet 1/1 Router(config-if)# media-ty[...]

  • Page 12

    5-12 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 252/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepaliv[...]

  • Page 13

    5-13 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input error[...]

  • Page 14

    5-14 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration Router# show version Cisco Internetwork Operating System Software IOS (tm) RPM Software (RPM-JS-M), Version 12.2(3.3)T, MAINTENANCE INTERIM[...]

  • Page 15

    5-15 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration MA Test History :00 MA Test History :01 EPROM format version 4 EPROM contents (hex): 0x00:04 22 40 02 22 C0 46 03 20 00 1C 0A 02 82 49 13 0[...]

  • Page 16

    5-16 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms Router# If the connection fails,[...]

  • Page 17

    5-17 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Note After you enter the addred command, the switch resets the secondary card; therefore, the secondary ca[...]

  • Page 18

    5-18 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Note The standby card must not hav e any conf igurations and must not be conf igured. Therefore, do not pr[...]

  • Page 19

    5-19 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards 04 Empty --- --- --- --- 05 Empty --- --- --- --- 06 Failed/Empty AXSM_1OC48 MINOR NA NO REDUNDANCY 07 Act[...]

  • Page 20

    5-20 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Step 6 Continue this procedure from Step 2 for all remaining cards. Upgrading Non-redundant RPM-PR Cards T[...]