English dropdown-ico

Crimestopper Security Products RS-999TW1/TW2 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Crimestopper Security Products RS-999TW1/TW2, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Crimestopper Security Products RS-999TW1/TW2 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Crimestopper Security Products RS-999TW1/TW2. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Crimestopper Security Products RS-999TW1/TW2 should contain:
- informations concerning technical data of Crimestopper Security Products RS-999TW1/TW2
- name of the manufacturer and a year of construction of the Crimestopper Security Products RS-999TW1/TW2 item
- rules of operation, control and maintenance of the Crimestopper Security Products RS-999TW1/TW2 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Crimestopper Security Products RS-999TW1/TW2 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Crimestopper Security Products RS-999TW1/TW2, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Crimestopper Security Products service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Crimestopper Security Products RS-999TW1/TW2.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Crimestopper Security Products RS-999TW1/TW2 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    RS-900/RS-901 COOLSTART SERIES VII RS-999TW1/TW2 2-WAY PAGING SYSTEMS REMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION Congratulations on your choice of a Crimestopper CoolStart™ remote engine starter! This installation Handbook covers the following models: RS900 VII Remote Start & Keyless Entry System, RS901 Upgrade/Expan[...]

  • Page 2

    TABLE OF CONTENTS Pre-Installation Considerations……….………...……...……………………………………………………………….……2 Cautions & Warnings…….…………...….……..…..……………………………………………………………….…..……3 Wiring……..………………………[...]

  • Page 3

    INSTALLATION CAUTIONS & WARNINGS **FOR SAFETY REASONS, DO NOT INSTA LL in vehicles with MANUAL TRANSMISSIONS .** If accidentally left in gear, a remote started vehicle could become a self-propelled threat to life and property. DO NOT extend the Remote start ignition harness length. Mount the module so that main harness reaches all ignition swit[...]

  • Page 4

    WIRING PIN 3: YELLOW/BLACK FOR NEGATIVE IGNITION OUTP UT: (Relay and/or Module not included) YELLOW /BLA CK 85 86 30 87 3rd IGN (If n eeded ) IGN S W . OR AN T I - T H E F T / MODUL E +12V CONST A NT OR TRA NSPONDER Diode i solate if us ing bo th! PIN 3: YELLOW/BLACK: FOR ANTI-GRIND/STARTER DISABLE OUTPUT: (Relay not included) TO IGN 2 MOTOR ACC ST[...]

  • Page 5

    WIRING PIN 4: BROWN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT This output is programmable for two modes of operation. See Programming Option Section. Mode (1) DEFAULT: Provides a Ground pulse when button #3 (Trunk) on the remote transmitt er is pushed to activate a factory electric trunk release or other optional accessory. Mode[...]

  • Page 6

    WIRING PIN 5: GREEN: (-) START ACTIVATION INPUT, OEM INTERFACE or TURBO TIMER INPUT See descriptions & diagrams below. Mode (1) [Default (-) Neg. Start Activation] This wire allows a host (or parent) alarm’s or keyless entry system to activate a Remote Start by sending a 1-Second Negative signal to the Green input wire to trigger a remote eng[...]

  • Page 7

    WIRING PIN 6: GRAY: (-) NEGATIVE HOOD PIN SWITCH (REQUIRED FOR PROGRAMMING) Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we recommend one be installed. When this wire is grounded, the remote start is inhibited. If hood is opened on a remote started engine, the unit will imme[...]

  • Page 8

    WIRING: 7-PIN HIGH-CURRENT CONNECTOR BROWN: +12V STARTER OUTPUT 30A: Connect to circuit in the vehicle that has pow er ONLY while the STARTER MOTOR is CRANKING. GRAY: +12V ACCESSORY OUTPUT 30A: Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typically, this wire turns ON with the first position of t[...]

  • Page 9

    WIRING: 7-PIN HIGH-CURRENT CONNECTOR FUSE RED PINK/WHITE 30A FUSE RED 30A + - BROWN PINK FUEL ENGI NE BA TTE R Y PUMP ECU GRA Y + ST ARTER - COIL IGN OR AC C H/V/AC Diagram not to scal e, for il lustrat ion purp oses only . Y our v ehicle may dif fer . IGN 2 AC C 2 TOP WH IT E ST A RT 2 FUSE P A RKING LIGHTS IF N ECE SSAR Y 7-PI N Hig h Current Con[...]

  • Page 10

    POWER DOOR LOCK WIRING CONNECTOR PIN 1: BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for Positive Door Lock systems. CS-610S1: Af[...]

  • Page 11

    BASIC DOOR LOCK DIAGRAMS A FTERM A RKET M OTOR/DOO R LOCK WIRING REVERSE POL A RITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 30 87A 30 87A 30 87A 30 87A + L CUT UL CUT MA STER SWITCH NEGA T IVE TRIGGE R DOORLOCK WIRI NG POSITIVE TRIGGER DOORL OCK WIRING GREEN GREEN FUSED RED +12V R[...]

  • Page 12

    “SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “S mart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor each time a remote start is requested. IMPO[...]

  • Page 13

    TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. When following the steps, the unit will begin to flash the parking lights if you have the Red/White wire connected to a tach source. If lights do not flash, then try another wire until you locate a tach signal that will [...]

  • Page 14

    TACH PROGRAMMING & TACH SIGNALS INTRODUCTION Tach signals will vary in levels and frequencies depending on m any factors including the type of vehicle and the source of the signal. The signals from a vehicle’s injector wire and coil pac wire can vary greatly even on the same engine. The tach signal from an engine can also affected by other so[...]

  • Page 15

    TIMED CRANK MODE This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a timed cranking output combined with the use of the Red/Wh ite tach wire as an engine ON/OFF monitor. The Red/White Tach wire must still be used in this mode of operation. THIS FEATURE MUST BE PROGRAMMED BEFORE USE! TH[...]

  • Page 16

    DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit”. This may be needed for various reasons. If your vehicle does not have a viable “Wait to Start Circuit”, or you cannot locate and identify the circuit, then change your system to “Diesel Glow Plug [...]

  • Page 17

    OPTIONS PROGRAMMING To Engage Option Programming: 1. Open hood (If no hood pin switch is installed, then ground the Gray wire) 2. Turn Key to the ON position. (Do not start vehicle) 3. Press the program / valet button 5 times. After a few seconds the unit will flash the lights 5 times. 4. Push the valet/program button [again] the number of times th[...]

  • Page 18

    OPTIONS PROGRAMMING 11. N/A - Not used N/A – Not used 12. Yellow/Black Wire (-) (-) IGN output or (-) Anti-Grind Anti-Grind *IGN output 13. Horn Chirp Confirmation with 2 presses of Lock/Unlock ON or OFF OFF *ON 14. Unlock/Disarm with Trunk pop activation Trunk Pop & Unlock or Trunk Pop Only Trunk Pop & Unlock *Trunk Pop Only 15. Timed Cr[...]

  • Page 19

    OPTIONS PROGRAMMING OPTION DESCRIPTIONS: 1. Engine Monitoring: This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a Tach signal (RPM) or for Tachless mode that monitors voltage level. See pages 11-15 for more information and additional steps for actual Tach learning and Tach finder modes.[...]

  • Page 20

    OPTIONS PROGRAMMING 7. Horn Chirps on Remote Start: This option allows the unit to provide 3 short chirps when for audible confirmation of a remote start. The horn output wire mu st be connected for this feature. 8. Lock During/After Remote Start: This option controls whether the unit will automatically lock during and after a remote Start abort or[...]

  • Page 21

    OPTIONS PROGRAMMING 17. OEM Disarm / Unlock Pulse: Some vehicles (namely Nissan and VW) require a shorter setting prevent the vehicle from attempting to roll down the windows due to the length of the UNLOCK and/or DISARM pulses. Use this option to SHORTEN the OEM Disarm/Unlock Pulses should your vehicle require this. Symp tom: Windows will slightly[...]

  • Page 22

    900 VII TRANSMITTER / 999TW1/TW2 TRANSCEIVER CODE LEARNING Transmitter/Transceiver Code Learning: (Excludes RS901 model without remotes) Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be learned at time of programming!! These systems all[...]

  • Page 23

    2-VEHICLE OPERATION The RS-900VII system can be used for 2 vehicle operation. A single remote can control two independent vehicles with an identical systems installed. NOTE: The RS-900 and RS-999 systems ARE NOT interchangeable. An RS-900VII system remote CANNOT control an RS-999TW1/TW2 and vice versa! See diagram below on how to switch your remote[...]

  • Page 24

    TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY): The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for 5-6 seconds then turn key off. Unit is now out of valet mode and should remote start. If opti onal LED is installed, then it will be on solid when in Val[...]

  • Page 25

    JUMPER PIN DIAGRAMS Jumper pi ns are used to change/configure the operation of the on board multi-function output PINK/WHITE wire, the Parking Light WHITE wire and the PINK glow plug input wire. See the diagrams below for Jumper Pin configurations. JUMPER PLUG SID E VIEW JUM PER PINS JP1 JUMPERS: IGN 2 (DEF AUL T) AC C 2 (-) NEGA TIVE P A RKING LIG[...]

  • Page 26

    ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCA TIONS Blue Plug Black Plug RS-900 VII RS-999TW1 RS-999TW2 Color of plug and receptacle must match! ! 26[...]

  • Page 27

    TRANSMISSION PROGRAM P ARKING LIG HTS SW ITCH ECU RS900/901 ANT ENNA/RECEIVER PLUG LED (-) UNL OCK OUTPUT +12 V FOR RELA YS (-) LOCK OUTPUT ENGIN E ECU GREEN BLUE RED FUEL PUMP PINK RED BROWN GRA Y RED WH I TE +10A or -.5A OUTPUT IGN RED/W HIT E T ACH INPUT ORANGE/BLA CK: (-)HOOD SW IT CH GRA Y (+12 V) BRAKE PEDA L RESET BLACK PURPLE BROW N ORANGE:[...]

  • Page 28

    ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2004 Crimestopper Security Products[...]