Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Delta 34-814, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Delta 34-814 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Delta 34-814. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Delta 34-814 should contain:
- informations concerning technical data of Delta 34-814
- name of the manufacturer and a year of construction of the Delta 34-814 item
- rules of operation, control and maintenance of the Delta 34-814 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Delta 34-814 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Delta 34-814, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Delta service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Delta 34-814.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Delta 34-814 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
INSTRUCTION MANUAL UNISA W ® 10" Right Tilting Arbor Saw (Models 34-801, 34-806, 34-814, 36-812) P ART NO. 422-04-651-0064 (01-15-02) Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canad[...]
-
Page 2
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaution[...]
-
Page 3
3 ADDITIONAL SAFETY RULES FOR CIRCULAR SA WS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instru[...]
-
Page 4
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s pl[...]
-
Page 5
5 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause [...]
-
Page 6
6 OPERA TING INSTRUCTIONS FOREWORD The Delta Unisaw is a 10" right tilting arbor saw . The Delta Unisaw features set the standar ds in the table saw industry . UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be [...]
-
Page 7
7 ASSEMBL Y INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE SAW TO THE POWER SOURCE UNTIL THE SAW IS COMPLETEL Y ASSEMBLED AND YOU UNDERST AND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING BLADE TIL TING MECHANISM HANDLE 1. Install fiber washer (A) Fig. 3, on the blade tilting mechanism shaft (B). Install key (C), into shaft keyway . 2. [...]
-
Page 8
8 ASSEMBLING L VC ST ARTER BOX TO CABINET If you purchased the machine with magnetic push button electrical controls, the saw is shipped with the starter box completely wired to the switch and motor . However , the starter box must be mounted to the saw cabinet. T o assemble the starter box (A) Fig. 7, to the saw cabinet, proceed as follows: 1. Pla[...]
-
Page 9
9 ASSEMBLING GPE ON/OFF SWITCH 1. The GPE on/of f switch (A) Fig. 11, is shipped attached to a mounting bracket at the right side of the machine. 2. Loosely assemble switch and switch bracket (A) Fig. 12, to the inside front lip of extension table with 5/16- 18x1" flat head screw (D), 5/16" flat washer (E), and 5/16 hex nut (F) through ho[...]
-
Page 10
10 Fig. 16 Fig. 17 Fig. 19 A D B F A J Fig. 18 Fig. 20 Fig. 21 4. If an adjustment is necessary , loosen two screws (F) Fig. 17, and adjust splitter bracket (A) until it is aligned with the inside blade flange (B) Fig. 15. Tighten two screws (F). Loosely assemble scr ew and fastener plate (C), which were r emoved in STEP 3. 5. Insert threaded end o[...]
-
Page 11
11 Fig. 22 Fig. 23 Fig. 25 Fig. 24 Fig. 26 Fig. 27 A P B X Z Y 8. Assemble upper splitter bracket (M) Fig. 22, to lower bracket (L) using a 5/16-18x1" hex head screw (N) with 5/16" lockwasher and 5/16" flat washer . NOTE: Do not tighten screw (N) at this time. 9. Insert the front end of splitter (P) Fig. 23, inside the splitter mount[...]
-
Page 12
12 Fig. 28 Fig. 30 E Fig. 29 F ASTENING MOTOR CORD TO SA W FRAME 1. IMPORT ANT : T urn the blade tilting handwheel counterclockwise as far as it will go until the saw blade is in the 45 degree position. 2. IMPORT ANT : T urn the blade raising and lowering handwheel counterclockwise until the blade is at its lowest position. 3. Fasten motor cord (A)[...]
-
Page 13
13 Fig. 35 Fig. 36 ASSEMBLING RIP FENCE HOLDER BRACKETS Assemble the rip fence holder brackets (A) and (B) Fig. 37, to the four holes located in the left hand side of the saw cabinet using four #10x1/2" sheet metal screws supplied. Fig. 38 Fig. 37 A B ASSEMBLING DUST CHUTE ADAPTER The Unisaw is supplied with a dust chute connector to provide a[...]
-
Page 14
14 OPERA TING CONTROLS AND UNISA W ADJUSTMENTS ST AR TING AND STOPPING THE SA W T o start the machine, push “ON” button (A) Fig. 39. T o stop the machine, push “OFF” button (B). Fig. 39 A B LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the machine is not in use, the switch should be locked in the “OFF” position using a padl[...]
-
Page 15
15 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS Positive stops are pr ovided to quickly and accurately position the blade at 90 and 45 degrees to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the saw blade all the way to the top and tur n the blade tilting handwheel clockwise as [...]
-
Page 16
16 ADJUSTING T ABLE INSER T Place a straight edge (B) across the table at both ends of the table insert as shown in Fig. 46. The table insert (A) should always be level with the table. If an adjustment is necessary , tur n the adjusting screws (C), as needed, with allen wrench supplied. NOTE: THE MITER GAGE HANDLE CAN BE USED TO STORE THE ALLEN WRE[...]
-
Page 17
17 MAINTENANCE CHANGING THE SA W BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. NOTE: T wo wrenches are supplied with the saw for changing the saw blade; a box end wrench and open end wrench. 3. Remove table insert and raise saw blade to its maximum height. 4. Place the open end wrench (B) Fig. 50, on the flats of the saw arbor to keep the arbor[...]
-
Page 18
18 PROTECTING CAST IRON T ABLE FROM RUST T o clean and protect cast iron tables fr om rust, you will need the following materials: 1 pushblock from a jointer , 1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40 ® , 1 can of degreaser , 1 can of T opCote ® Aerosol. Apply the WD-40 and polish the table surface with the Scotch-Brite[...]
-
Page 19
19 Fig. 56 A Fig. 57 B Fig. 58 USING THE FENCE AS A CUT -OFF GAGE WARNING: WHEN USING YOUR UNIFENCE AS A CUT -OFF GAGE, MAKE SURE IT IS PROPERL Y SET UP AS DESCRIBED HERE. The fence can be used as a cut-off gage when cr oss cutting a number of pieces to the same length. IMPORT ANT : When using the fence as a cut-off gage, it is very important that [...]
-
Page 20
20 Fig. 61 USING AUXILIAR Y WOOD F ACING ON BIESEMEYER RIP FENCE It is necessary when performing special operations such as moulding to add wood facing (A) Fig. 62, to one or both sides of the rip fence, as shown. The wood facing is attached to the fence with two clamps (B). 3/4 inch stock is suitable for most work although an occasional job may re[...]
-
Page 21
21 Fig. 65 Fig. 66 G H W IMPORT ANT : For certain cutting operations such as dadoing and moulding where you ar e not cutting completely through the workpiece, the blade guar d and splitter assembly cannot be used. Loosen screws (G) and (H) Fig. 65. Lift up and swing blade guard and splitter assembly (W) Fig. 66, to the rear of the saw , and then ti[...]
-
Page 22
22 Fig. 69 Fig. 70 Fig. 71 A B C USING ACCESSOR Y DADO HEAD IMPORT ANT : THE BLADE GUARD AND SPLITTER ASSEMBL Y CANNOT BE USED WHEN DADOING OR MOULDING AND MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW . Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, a[...]
-
Page 23
23 CONSTRUCTING A FEA THERBOARD Fig. 74, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should be a straight piece of wood that is free of knots and cracks. Featherboar ds are used to keep the work in contact with the fence and table and help prevent kickbacks. Clamp the featherboar[...]
-
Page 24
24 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the fe[...]
-
Page 25
25 BLADE GUARD ACCESSORIES Deluxe Uniguar d ® Blade Guar d The Delta Model 34-976 Uniguard Blade Guar d with Splitter and Anti-kickback Fingers Fig. 77, is an accessory that can be used in place of the standard blade guard that is supplied with the Unisaw . The Delta Model 34-976 Uniguard Blade Guar d can be mounted to the Unisaw , the Unisaw with[...]
-
Page 26
26 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with[...]
-
Page 27
27 NOTES[...]
-
Page 28
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , POR T A-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SA W BOSS ® , SPEED-BLOC ® , SPEEDMA TIC [...]