Go to page of
Similar user manuals
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Delta 46-715, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Delta 46-715 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Delta 46-715. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Delta 46-715 should contain:
- informations concerning technical data of Delta 46-715
- name of the manufacturer and a year of construction of the Delta 46-715 item
- rules of operation, control and maintenance of the Delta 46-715 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Delta 46-715 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Delta 46-715, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Delta service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Delta 46-715.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Delta 46-715 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
INSTRUCTION MANUAL P ART NO. 903742 - 03-18-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 14" V ariable Speed W ood Lathe (46-715)[...]
-
Page 2
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop[...]
-
Page 3
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf[...]
-
Page 4
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA[...]
-
Page 5
5 ADDITIONAL SAFETY RULES FOR WOOD LA THES 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical connections.[...]
-
Page 6
6 Fig. A Fig. B GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER 2. Grounded, cor d-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts: If the machine is intended for use on a circuit that has an outlet that looks like[...]
-
Page 7
7 FOREWORD FUNCTIONAL DESCRIPTION NOTICE: The photo on the manual cover illustrates the curr ent production model. All other illustrations contained in the manual are r epresentative only and may not depict the actual color , labeling, or accessories and are intended to illustrate technique only . The Delta 46-715 14" adjustable speed wood lat[...]
-
Page 8
8 ASSEMBLING THE ST AND 1. Attach the two long tie bars (A) Fig. 3 (with the flanges up) to the center of each stand leg (B) by using eight carriage bolts through the legs and tie bars, secur ed by flat washers, lockwashers, and hex nuts. NOTE: Hand-tighten the hardwar e for further adjustment. 2. Attach two short tie bars (C) Fig. 3 (with the flan[...]
-
Page 9
9 HEADSTOCK SPUR CENTER The 46-715 comes with a faceplate attached. Before inserting the spur center in the spindle, remove this faceplate. Insert the knockout bar (A) Fig. 10 in the side hole of the spindle (B) Fig. 10 to hold the spindle in place. Use the supplied wrench (C) Fig. 10 to loosen the faceplate. Remove the faceplate (D) by turning it [...]
-
Page 10
10 ADJUSTING CLAMP ON TOOL REST T o adjust the tool rest clamping action, use a 15/16" wr ench to adjust the nut (A) Fig. 16 in the same manner as the headstock and tailstock. A TT ACHING ON/OFF SWITCH TO TOOL The "ON/OFF" switch comes unattached to the tool to protect it fr om damage in shipping. T o attach the "ON/OFF" Sw[...]
-
Page 11
11 ACTIV A TING THE SPINDLE IMPORT ANT : Unlock the spindle lock BEFORE operating the tool. The unlocked position is shown in Fig. 23A while the locked position is shown in Fig. 23B. CHANGING SPEED RANGES IMPORT ANT : Change speeds ONL Y when the tool is running. This tool provides variable rate spindle speeds fr om 600 to 2200 RPM. T o change spee[...]
-
Page 12
12 HOW TO TURN SPINDLES Spindle turning is the principal type of wood tur ning (chair and table legs, lamp stems, etc.) The turning of spindles can be done with either a scraping or cutting technique. The cutting technique, by virtue of faster wood removal and a cleaner surface, is the p r eferred method. Fig. 27 CENTERING THE WORK W ood stock for [...]
-
Page 13
13 TOOL REST POSITION Mount the tool rest in place about 1/8” away from the work and 1/8” above the work centerline (Fig. 32.) This position may vary to suit both you and the work. Place a guide mark on the tool rest shank as an aid to quick and accurate r esetting. Clamp the tool rest firmly befor e operating the lathe. Fig. 32 ROUGHING A CYLI[...]
-
Page 14
14 SMOOTHING A CYLINDER T o smooth a cylinder , use a large skew chisel. This requir es practice, but experience with this tool is very important. Place the cutting point near the c enter of chisel and high on the work (Fi g. 3 8). Sometimes, in striving for a certain position in relation to the work, the beginner will often overlook this all-impor[...]
-
Page 15
15 CUTTING A SHOULDER Use the parting tool first to reduce the wood to within 1/16” of the requir ed shoulder and diameter (Fig. 43). Clean the waste stock out with the gouge (Fig. 45A), then use the skew for the actual cutting of the shoulder (Figs. 45A and 45B), which is a duplication of squaring an end. The skew then makes the horizontal cut, [...]
-
Page 16
16 VEE GROOVES Cutting the vee groove demands much the same technique as the bead, except that the skew is hinged straight into the work without rotation (Fig. 51). Only one-half of the vee is made at a time, and one, two, or more cuts may be needed on each side to obtain the desired shape. As in all cutting with the skew , use the bevel next to th[...]
-
Page 17
17 Place the gouge on edge on the tool rest so that the grind of the chisel forms an approximate right angle with the work (Fig. 57). The chisel contacts the work at the center of the cutting edge. Hold the tool so that the centerline of the gouge is pointing directly towar d the center of the revolving stock. This starting position is important to[...]
-
Page 18
18 MOUNTING THE WORKPIECE TO THE F ACEPLA TE Fig. 63 shows direct mounting to the 3” faceplate along with attaching to the backing block. Because of the ease of setting up, use this mounting whenever the work permits. Hold lar ger pieces in the same way by using the 6” faceplate. When normal screw- fastenings interfere, mount the work on a back[...]
-
Page 19
19 8. Fig. 69 illustrates the rough cutting of the inside of a bowl. 9. Outboard turning is illustrated in Fig. 70. Note that the headstock (A) is turned 45 degrees and the tool rest auxiliary extension (B) is attached. Outboard turning generally is used for larger workpieces, but smaller work can be accomplished using this technique. MAINTENANCE B[...]
-
Page 20
20 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra[...]
-
Page 21
21 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with [...]
-
Page 22
22 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized ser[...]
-
Page 23
23 NOTES[...]
-
Page 24
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T[...]