Ford 2006 F-250 manual

Introduction 4 Instrument Cluster 12 W arning and control lights 12 Gauges 16 Entertainment Systems 20 AM/FM stereo 20 AM/FM stereo with CD 22 AM/FM stereo cassette with CD 25 AM/FM stereo with in-dash six CD 28 Climate Controls 33 Heater only 33 Manual heating and air conditioning 34 Automatic temperature control 36 Lights 39 Headlamps 39 T urn si[...]

Locks and Security 80 Keys 80 Locks 80 Seating and Safety Restraints 89 Seating 89 Safety restraints 96 Airbags 107 Child restraints 116 Tires, Wheels and Loading 128 T ire Information 131 T ire Inflation 132 V ehicle loading 146 T railer towing 153 T railer Brake Controller -Integrated 157 Recreational towing 163 Driving 165 Starting 165 Brakes 17[...]

Cleaning 241 Maintenance and Specifications 249 Engine compartment 251 Engine oil 254 Battery 258 Engine Coolant 260 Fuel information 266 Air filter(s) 284 Part numbers 286 Refill capacities 287 Lubricant specifications 290 Accessories 304 Index 307 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, rec[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company , Ford of Canada, and service and repair facilities may access vehicle diagnostic information through a direct connection [...]

Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury . Front seat mounted rear -facing child or inf[...]

Before you drive your vehicle, please read this Owner’ s Guide carefully . Y our vehicle is not a passenger car . As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover , personal injury or death. Be sure to read Driving off road in the Driving chapter . Using your ve[...]

Using your vehicle as a stationary power source (PTO) Refer to the Driving chapter for more information and guidelines for operating a vehicle equipped with an aftermarket power take-off system. Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are di[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag-Front Airbag-Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfunction S[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES Standard instrument cluster (manual transmission) Standard instrument cluster (automatic transmission) Amarillo instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your[...]

Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains on after starting the vehicle, have the respective system inspected immediately . If your vehicle is equipped with a diesel engine, it has a unique cluster , refer to Starting the engine in your 6.0 Liter Power Stroke Direct Injection T urbo Di[...]

after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your servicing authorized dealer . Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur . It will take you longer to stop the vehicle. Have the vehicle ch[...]

Four wheel drive low: Illuminates when four -wheel drive low is engaged. Four wheel drive indicator: Illuminates when four -wheel drive is engaged. Speed control: Illuminates when the speed control is activated. T urns off when the speed control system is deactivated. T urn signal: Illuminates when the left or right turn signal or the hazard lights[...]

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Amarillo instrument cluster Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop [...]

Odometer: Registers the total miles (kilometers) of the vehicle. • W ith Mini Message Center • W ith Full Message Center Refer to Message Center in the Drivers Controls chapter on how to switch the display from Metric to English. T rip odometer: Registers the miles (kilometers) of individual journeys. • W ith Mini Message Center Press and rel[...]

T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Standard instrument cluster Amarillo instrument cluster Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” an[...]

Battery voltage gauge (manual transmission only): Indicates the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range, have the vehicle’ s electrical system checked as soon as possible. T ransmission fluid temperature gauge (automatic transmission only): If the gauge is in the: [...]

AUDIO SYSTEMS AM/FM stereo system (if equipped) 1. / T uner: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Audio: Press to access select various settings. T reble: Press to adjust the treble setting. Use / / SEEK, SEEK . Bass: Press to adjust the bass setting. Use / / SEEK, SEEK . Balance[...]

3. Seek: Press to access the next/previous strong station or track. 4. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 5. AM/FM: Press to select AM/FM frequency band. 6. ON/OFF/V olume: Press to turn ON/OFF . T urn to increase/decrease volume. If the volume is se[...]

AM/FM stereo/single CD sound system (if equipped) 1. / T uner: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strong[...]

T reble: Press to adjust the treble setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for [...]

11. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 12. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. 13. Seek: Press to access the previous strong station or track. 14. AM/FM: Press to select AM/FM frequency band. 15. ON/O[...]

AM/FM stereo cassette/single CD sound system (if equipped) 1. / T uner: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Seek: Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 4. Menu: Press to toggl[...]

Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Press MENU to access and use / / SEEK to adjust. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed[...]

9. Repeat: Press to repeat the current CD track. 10. Fast forward: Press to manually advance in a CD track or cassette. 11. Rewind: Press to manually reverse in a CD track or cassette. 12. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. T ape: Insert a tape f[...]

19. CD slot: Insert a CD label side up. 20. Seek: Press to access the previous strong station or track. 21. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. When this radio is used in cargo vans where no rear speakers are installed in the vehicle, fading to the rear speakers will result in no audio output. Premi[...]

3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press MENU to access. Use / / SEEK to set. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less tha[...]

7. Comp (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 8. Repeat: Press to repeat the current CD track. 9. Fast forward: Press to manually advance in a CD track. 10. Rewind: Press to manually reverse in a CD track. 11. Memory presets: T o set a station: Select frequency band AM/FM; tune t[...]

17. LOAD: Press to load a CD, then select a slot number using the radio presets 1 through 6. If you don’t select a slot within 5 seconds, the radio shall choose the first available slot for you. Press and hold for 2 seconds to auto load up to six CDs. 18. CD eject: Press to eject a CD, then select the desired CD slot using the radio presets 1 thr[...]

• Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity or cold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, [...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control: : Distributes outs[...]

T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Modulate the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instr[...]

: Distributes outside air through the instrument panel vents, floor vents and center console vents (if equipped). O (OFF): Outside air is shut out and the climate system is turned off. : Distributes outside air through the floor vents. : Distributes outside air through the windshield defroster vents, floor vents and demister vents. : Distributes ou[...]

AUTOMATIC T EMPERATURE CONTROL SYSTEM (IF EQUIPPED) Press the AUTO and (floor/defrost) controls at the same time and hold for one second to switch between Fahrenheit and Celsius. 1. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . Engages automatically in AUTO, (defrost), [...]

6. (Floor): Distributes air through the floor vents. 7. (Panel/floor): Distributes air through the instrument panel vents, floor vents and center console vents (if equipped). 8. (Panel): Distributes air through the instrument panel vents and center console vents (if equipped). 9. OFF: Outside air is shut out and the climate control system is turned[...]

• T o improve the A/C cool down, drive with the windows slightly open for 2–3 minutes after start up or until the vehicle has been “aired out.” For maximum cooling performance in AUTO mode: • Press AUTO control and set to desired temperature. For maximum cooling performance using manual override modes: • Press (panel), A/C, with recircu[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also kee[...]

Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the , or position and the high beams are not turned on. In autolamp mode, the foglamps won’t be operational until lighting conditions warrant the activation of the headlamp/parklamp lighting. Pull headl[...]

High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move t[...]

V ertical and horizontal aim adjustment (sealed beam headlamps) The headlamps on your vehicle are intended to be aimed using mechanical aimers. If mechanical aimers are used and the cross-car sight line is in any way blocked, set the legs of the universal adaptor all to the same setting, such that the cross-car sight line is no longer blocked, per [...]

5. Locate the vertical adjuster (2) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down). 6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen. 7. On the wall or s[...]

• (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). 3. T urn on the low beam headlamps to illuminate the wall or sc[...]

T URN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. COURTESY/READING LAMPS (IF EQUIPPED) The dome lamp illuminates when any door is not completely closed, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is o[...]

BULBS Headlamp condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur . This condensation is normal and will clear within 45 minutes of headlamp operation. Replacing exterior bulbs Check the operation of all the bulbs frequently . Functi[...]

2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp is difficult, removing the four screws along the top of the grill will help provide more clearance. 4. Disconnect the electrical connector by[...]

Replacing park/turn and sidemarker lamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp [...]

Replacing headlamp bulbs (sealed beam) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp is difficult, removin[...]

Replacing park/turn/sidemarker bulbs (sealed beam) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp is diffic[...]

Replacing tail lamp/turn/backup lamp bulbs — F–250/F–350 only 1. Make sure the headlamp switch is in the OFF position and then open the tailgate to expose the lamp assemblies. 2. Remove the two bolts from the tail lamp assembly and carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs. 3. Rotate the bul[...]

Replacing cargo lamp and high-mount brakelamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the two screws and lamp assembly from vehicle as wiring permits. 3. Remove the bulb socket by rotating counterclockwise. 4. Pull the bulb straight out of the socket. Front clearance and identification lamp bulbs 1. Make sure the he[...]

Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. T wist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly . 3. Pull out the old bulb from the socket and push in the new [...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]

T RANSMISSION CONTROL T ow/Haul feature (5–speed automatic transmission) (if equipped) T o activate, press the transmission control switch (TCS) located on the gearshift. The TOW/HAUL indicator light will illuminate in the instrument cluster . The transmission will operate in all gears. Press the transmission control switch again to deactivate T [...]

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet for this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The auxiliary[...]

Press and hold the bottom part of the rocker switch to open the window . Press and hold the top part of the rocker switch to close the window . One touch down Allows the driver’ s window to open fully without holding the control down. Press completely down on AUTO and release quickly . Press again to stop. Window lock (if equipped) The window loc[...]

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Y our vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror . When the mirror detects bright light from front or behind, it will aut[...]

T ype A The mirror heating elements are designed to operate regardless of the geographic location of the vehicle. There is no switch to turn on, or other operator involvement required other than to start the vehicle. T ype B The spotter mirror , below the main mirror , is not heated and must be adjusted manually . Do not remove ice from the mirrors[...]

Clearance lamps (if equipped) Illuminates when the headlamps or parking lamps are switched on. This provides additional visibility of your vehicle to other drivers on the road. Fold-away mirrors The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the tr[...]

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 2.75 inches (70 mm) of maximu[...]

3. Press the SET ACCEL control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • V ehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to red[...]

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the COAST control until you get to the desired speed, then release the control. Y ou can also use the COAST control to operate the T ap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 k[...]

UPFITTER CONTROLS (IF EQUIPPED) Y our vehicle may be equipped with the Upfitter option package which will provide four switches, mounted in the center of the instrument panel, labeled AUX 1, AUX 2, AUX 3 and AUX 4. These switches will only operate while the ignition is in the 4 (ON) position, whether the engine is running or not. It is, however , r[...]

The relays and fuse in the glove box are coded as shown in the accompanying illustration. There will also be one power lead for each switch found as a blunt-cut and sealed wire located behind the passenger compartment fuse panel. They are coded as follows: Switch Circuit number W ire color Fuse AUX 1 1936 Orange with Light Green T race 30A AUX 2 19[...]

STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features • Press MODE to select AM, FM1, FM2, T APE or CD (if equipped). In Radio mode: • Press NEXT to seek/scan to the next strong station. In T ape mode: • Press NEXT to listen to the next selection on the tape. [...]

Press and release the control again to fully open. T o stop the one-touch open feature press either the AUTO or control again. T o close the moon roof: Press and hold the control until the glass panel stops at the “comfort” position. Press and hold the control again until the glass stops moving. When fully closed, the rear portion of the glass [...]

Note: The following warning messages will reappear after an ignition OFF-ON cycle has been completed. Door ajar: Displays when the ignition is in the ON position and any door is open. Check fuel cap: Displays when the fuel cap may not be properly installed. Continued driving with this display on may cause the Service engine soon warning light to co[...]

• The engine oil pressure is low . • The fuel gauge is at or near empty . Check trailer (if equipped): Displayed when a trailer connection becomes disconnected, either intentionally or unintentionally , and has been sensed during a given ignition cycle. Refer to Integrated trailer brake controller in the T ires, Wheels and Loading chapter for m[...]

Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer/Compass • T rip odometer/Odometer/Compass • Distance to Empty/Odometer/Compass • A verage Fuel Economy/Odometer/Compass • Engine hour meter/Odometer/Co[...]

degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error . Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2. T urn ignition to the ON position. 3. Start the engine.[...]

7. Press the RESET control to start the compass calibration function. 8. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWL Y TO CALIBRA TE display changes to CALIBRA TION COMPLETED. It will take up to five circles to complete calibration. 9. The compass is now calibrated. Distance to empty (DTE) Selecting this f[...]

• Differences in the automatic shut-off points on the fuel pumps at service stations • V ariations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record t[...]

1. ENGINE TEMP 2. TRANS TEMP 3. OIL PRESSURE 4. BRAKE FLUID LEVEL 5. DOOR AJAR 6. FUEL CAP 7. AIR FIL TER (diesel only) 8. FUEL LEVEL Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Autolocks This feature automatically locks all ve[...]

Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’[...]

W arning display Status Reduced engine power W arning cannot be reset Stop engine safely Low fuel level W arning returns after 10 minutes Low brake fluid level Low oil pressure Check engine temperature T railer disconnected W ater in fuel (diesel only) Check air filter (diesel only) Door ajar W arning returns after the ignition key is turned from O[...]

LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low and the brake system should be inspected immediately . Refer to Checking and adding brake fluid in the Maintenance and Specifications chapter . LOW OIL PRESSURE. Displayed when the engine oil pressure is low . If this warning message is displayed, check the level of the engine oil. Refer[...]

DA T A ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Odometer • Fuel flow • Fuel level • T rans temp • Fuel cap • Engine sensor • Brake fluid • Auto lock • Auto lamp delay Contact your authorized dealer as soon as possible if these messages occur on a regular bas[...]

T ailgate removal Y our tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw . Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45–degree angle. 5. Lift right side off of its hinge. 6. Lift left side off[...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Y our keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through[...]

CHILDPROOF DOOR LOCKS (IF EQUIPPED) • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatica[...]

• unlock the vehicle doors without a key . • lock all the vehicle doors without a key . • activate the personal alarm. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press and release to[...]

• the ignition is turned to the 4 (ON) position, • unlocking the vehicle using the keyless entry keypad, • or using the UNLOCK control on your remote entry transmitter (if equipped). This feature is initially deactivated, but may be activated by taking your vehicle to an authorized dealer . Sounding a panic alarm Press to activate the alarm. [...]

4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the battery down to ensure that the battery is fully seated in the battery housing cavity . 5. Snap the two halves back together . Note: Replacement of the battery will not cause the remote transmitter to become de[...]

8. W ithin 20 seconds, program the remote entry transmitter by pressing any button on the transmitter . Note: If more than 20 seconds have passed you will need to start the procedure over again. 9. The doors will again lock, then unlock, to confirm that this remote entry transmitter has been programmed. 10. Repeat Step 8 to program each additional [...]

KEYLESS ENTRY SYSTEM Y ou can use the keyless entry keypad to lock or unlock the doors without using a key . The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’ s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer . Y ou can also create [...]

The anti-scan feature will turn off after: • one minute of keypad inactivity . • pressing the control on the remote entry transmitter . • the ignition is turned to the 4 (ON) position. Unlocking and locking the doors using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code. Each number mus[...]

3. Close all the doors, liftgate and cargo doors. 4. Enter the 5-digit entry code. 5. Press and hold the 7 • 8. While holding the 7 • 8, press and release the 3 • 4. 6. Release the 7 • 8. The horn will chirp once when the system has been successfully deactivated. The horn will chirp twice (one short and one long chirp) when the system has b[...]

SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Head restraints The purpose of these head restraints is to help limit head mo[...]

Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the lever located at the bottom of the seatback to quickly fold the seatback forward. • Pull up on the lever located at the side of the seat cushion to recline the seatback and to return the sea[...]

40/20/40 front seat armrest and console (if equipped) T o release the armrest, pull forward on the strap and pull the armrest down. T o gain access to the storage compartment in your armrest, lift the latch to open the lid. The lid cannot be opened in the upright position. Lift up armrest to return it to a center seatback. 2006 F-250/350/450/550 (f[...]

Captain’ s chair (if equipped) • Lift the bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • T o recline the seatback, pull the release lever handle located on the side of the seat up. • Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward. Adj[...]

Press to raise or lower the rear portion of the seat cushion. • T ype A • T ype B • T ype A Press the control to move the seat forward, backward, up or down. • T ype B Press the control to move the seat forward or backward. 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Seating and Safety Restraints 93[...]

Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle. Heated seats (if equipped) T o operate the heated seats, do the following: • Push control to activate. • Push again to deactivate. The indicato[...]

REAR FOLDING SEAT SYSTEM WITH LOAD FLOOR (IF EQUIPPED) The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position. 1. Pull down the latch lever located on the bottom seat back to fold the seat back forward. 2. Pull up on the lever located on the side of the seat cushion to rotate the cushion up until it[...]

T o gain access to the cupholders and tray , pull down on the armrest. T o gain access to the 60/40 load floor , store the cushion in the upright locked position. Pull up on the straps located at the sides of the load floor , and rotate forward until resting on the carpet. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with y[...]

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]

2. T o unfasten, push the release button and remove the tongue from the buckle. The front outboard and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front outboard passenger and rear seat outboard safety belts have two types of locking modes described below: V ehicle sensitive mode This is the normal ret[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the a[...]

BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in the W orkshop Manual . Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Energy Man[...]

• 4–door Super Cab T o adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place. Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt prop[...]

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. • 1st row center seating position The lap belt does not adjust automatically . Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tong[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.[...]

If... Then... The driver’ s safety belt is buckled before the ignition switch is turned to the ON position... The BeltMinder 娂 feature will not activate. The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur eve[...]

Reasons given... Consider ... “The people I’m with don’t wear belts” Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed[...]

• the parklamps/headlamps are in OFF position T o reduce the risk of injury , do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE) 2. W ait until the safety belt warning light turns off. (Approximately 1 minute) • Step 3 must be complet[...]

Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary . All safety belt assemblies, including retractors, buc[...]

Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver , should always properly wear their safety belts, even [...]

Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. See your authorized dealer . The front passenger air bag is not designed to offer protection to an occupant in the center front seating position. Modifying or adding equipment to the front end of the vehicle (including frame, bumper , front end bod[...]

How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activatio[...]

If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators and airbags), • one or more impact and safing sensors, ?[...]

Passenger airbag ON/OFF switch (if equipped) An airbag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings. Failure to put the switch in a proper position can increase the risk of serious injury or d[...]

An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned off. Turning the passenger airbag back on The passenger airbag remains OFF until you turn it back ON. 1. Insert the ignition key [...]

If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . If a child in a rear facing infant seat must be transported in front, the passenger airbag must be turned OFF . This is because the back of the infant seat is too close to the inflating airbag an[...]

• the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’ s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger airbag to pose[...]

• the child has a medical condition that, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’ s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the ai[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. C[...]

Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child st[...]

The shoulder belt should cross the chest, resting snugly on the center of the shoulder . The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. The importance of[...]

• Review and follow the information presented in the Airbag supplemental restraint system (SRS) section in this chapter . • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from). • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make [...]

Installing child safety seats with combination lap and shoulder belts 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An airbag can kill or injure a child in a child seat. Child seats should NEVER be placed in the front seats, unless the passenger airbag switch is turned off, See Passenger airbag on/off switch [...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. T[...]

The SuperCab rear seat has three straps behind the top of the seat back that function as both routing loops for the tether straps and anchor loops. The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work prope[...]

installing the child seat. Refer to the Rear folding seat system with load floor section in this chapter for information on how to operate the rear seats. 5. Clip the tether strap to the anchor as shown. • Front seats (Regular Cab) • Front seat (SuperCab) • Rear seats (Crew Cab) If the tether strap is clipped incorrectly , the child safety se[...]

6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. 7. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. If the safety seat is not anchored properly , the risk of a child being[...]

3. Install the child safety seat tightly using the vehicle belts. Follow the instructions in this chapter . 4. T ighten the tether strap according to the child seat manufacturer’ s instructions. A single loop can be used to route and anchor more than one child seat. For example, the center loop can be used as a routing loop for a child safety sea[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on shifting procedures and maintenance can be found in your Owner’ s Guide .Y o u should become thoroughly familiar with this information before you operate your vehicle. On some 4W[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. T raction AA A B C[...]

• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 ps[...]

Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended[...]

Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the T ire Label or Safety Compliance Certification Label which is located on the B-Pillar or the edge of the driver’ s door . Failure to[...]

4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T -type/mini-spare tires (see T -T ype/Mini-Spare T ire Information section for description): Store and maintain at 60 psi (4.15 bars). For Full Size and Dissimilar spare tire[...]

Stay out of the trajectory (1) as indicated in the illustration. TIRE REPLACEMENT REQUIREMENTS Y our vehicle is equipped with tires designed to provide a safe ride and handling capability . Only use replacement tires and wheels that are the same size and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally[...]

INFORMATION CONTAINED ON THE TIRE SIDEWALL Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification and in case of a recall. I[...]

6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry . Y ou may find this information in your Owner’ s Guide. If not, contact a local tire dealer . Note: Y ou may not find this information on all tires because it is not required by federal law . 7. H: Indicates the tire’ s speed rating. The [...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For exa[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on either the T ire Label or Safety Compliance Certi[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

TIRE CARE Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding an[...]

• A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of [...]

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly , providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km). • Rear Wheel Dri[...]

• DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. W e do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair . After tire rotation, inflation pressures must be adjusted for the tires new position[...]

The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used, as chains may chip aluminum wheels. Follow these guidelines when using snow tire[...]

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label (vehicles exported outside the U.S. and Canada may not have a T ire Label) on the B-Pillar or the edge of the driver’ s door . Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD [...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Tires, Wheels and Loading 148[...]

GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the T ire Label or Safety Compliance Certification Label loca[...]

GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the T ire Label or Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The GVW must never exceed the GVWR. Exceeding the T[...]

Maximum Loaded T railer W eight – is the highest possible weight of a fully loaded trailer the vehicle can tow . It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your a[...]

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the avail[...]

Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this owner guide. Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower sp[...]

components carefully prior to and after any towing operation. Refer to T ransmission temperature gauge in the Instrument Cluster chapter for the transmission fluid temperature information. The following trailer towing charts apply to vehicles equipped with gasoline engines; for vehicles equipped with diesel engines, refer to your 6.0 Liter Power St[...]

Hitches Do not use hitches that clamp onto the vehicle’ s bumper or attach to the axle. Y ou must distribute the load in your trailer so that 10%–15% for conventional towing or 15%-25% fifth-wheel towing of the total weight of the trailer is on the tongue. Integrated hitch rating The standard integrated hitch has two ratings depending on mode o[...]

T owing trailers beyond the maximum tongue weight exceeds the limit of the towing system and could result in vehicle structural damage, loss of vehicle control and personal injury . Load equalizing hitch When hooking up a trailer using a load equalizing hitch, always use the following procedure: 1. Park the unloaded vehicle on a level surface. W it[...]

The braking system of the tow vehicle is rated for operation at the GVWR not GCWR. Integrated trailer brake controller (if equipped) Y our vehicle may be equipped with a fully integrated electronic T railer Brake Controller (TBC). When used properly , the TBC helps ensure smooth and effective trailer braking by powering the trailer’ s electric br[...]

3. GAIN setting display: Shows the current GAIN setting. This will illuminate when a trailer is connected, flash if the trailer becomes disconnected, or remain off if no trailer is connected. 4. OUTPUT bar graph: When the vehicle’ s brake pedal is pushed, or when the manual control is activated, green bar indicators will illuminate to indicate th[...]

5. In a traffic-free environment, tow the trailer on a dry , level surface at a speed of 20 – 25 mph (30 – 40 km/h) and squeeze the manual control lever completely . 6. If the trailer wheels lock-up (indicated by squealing tires), reduce the GAIN setting; if the trailer wheels turn freely , increase the GAIN setting. Repeat Steps 5 and 6 until [...]

Points to Remember: • Remember to adjust gain setting before using the TBC for the first time. • Readjust GAIN setting on the TBC (according to procedure above) whenever road, weather and trailer or vehicle loading conditions change from those that existed when the gain was initially set. • The sliding lever on the TBC should be used only for[...]

Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (112 km/h) during the first 500 miles (800 km) of trailer towing and don’t make full-throttle starts. • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed r[...]

• When turning make wide turns to allow trailer tires to properly clear any obstacles. • Be prepared for trailer sway due to buffeting when larger vehicles pass in either direction. • Refer to the Lubricant Specifications in this chapter for the proper axle lubricant. • Remember that regardless of the rear axle lubricant used, do not tow a [...]

Tires • All trailer tires should be of the same size, and construction. • Select tires that meet the trailer loading requirements. • Always check tow vehicle and trailer tire pressure before towing. Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above[...]

4x4 with manual shift transfer case: • Place the transfer case in N (Neutral). • Front hub locks are in the FREE position. 4x4 electronic shift transfer case vehicles with automatic transmissions: Regarding recreational towing or having your vehicle towed, 4x4 vehicles with electronic shift on the fly cannot be towed with any wheels on the grou[...]

STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. For vehicles equipped with a manual transmission, you must depress the ignition release lever to release t[...]

Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehi[...]

If starting a vehicle with an automatic transmission: 1. Make sure the parking brake is set. 2. Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor . 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Driving 167[...]

• T urn the key to 4 (ON) without turning the key to 5 (ST ART). 1 2 3 4 5 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Driving 168[...]

Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. Starting the engine 1. T urn the key to 4 (ON) without turning the key to 5 (ST ART). 2. T urn the key to 5 (ST ART), then release the key as s[...]

Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air . USING THE ENGINE BLOCK HEATER (IF EQUIPPED) Use of an engine block heater is strongly recommended if you live in a region wher[...]

Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a litt[...]

Parking brake T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated until the parking brake is released. Pull the right side of the release lever to release the parking brake; the release lever pulls at an angle toward the driver’ s[...]

Note: If your vehicle is equipped with a manual transmission, the engine may be required to run while power accessories operate and the parking brake is set. It is recommended that wheel chocks be used during this operation. If you’re parking your vehicle on a grade or with a trailer , press and hold the brake pedal down, then set the parking bra[...]

exhibit a slight noise or vibration in tight turns with low vehicle speed. This is normal behavior and indicates the axle is working. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person weari[...]

2. Insert the key and turn it to 3 (OFF). Apply the brake pedal and shift to N (Neutral) . When the key is in the ignition and in the OFF position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. T o avoid unwanted vehicle movement, always set the parking brake. 3. Start the vehicle.[...]

Understanding the shift positions of the 5–speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of service or repair , the transmission will need to[...]

N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with T ow/Haul OFF D (Overdrive) with T ow/Haul OFF is the normal driving position for the best fuel economy . The overdrive function allows automatic upshifts and downshifts through g[...]

3 (Third) T ransmission starts and operates in third gear only . Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearsh[...]

T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral position. 3. Start the engine, then press the brake pedal and release the parking brake. 4. Move the gearshift lever to 1 (First) gear , then slowly release the clutch pedal while slowly pressing o[...]

Maximum downshift speeds 1 6-speed transmission Shift from: T ransfer case position (if equipped) 2 2H or 4H 4L D (Overdrive) - 4 45 mph (72 km/h) 16 mph (26 km/h) 4-3 35 mph (56 km/h) 12 mph (19 km/h) 3-2 20 mph (32 km/h) 8 mph (13 km/h) 2-1 5 mph (8 km/h) 2 mph (3 km/h) 1-LO Only shift to LO when at a stop. 1 Use 2H or 4H for 4WD equipped vehicle[...]

Removing the key T urn the ignition off, push the release lever (located above the ignition), then turn the key toward you and remove the key . REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds [...]

The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound conti[...]

If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this [...]

LOW (4WD Low) can be engaged, the vehicle speed must be below 3 mph (5 km/h) with the brake pedal depressed and the transmission in N (Neutral). This vehicle is equipped with a non-synchronous low range gearset which will not allow the transfer case to shift into 4X4 LOW (4WD Low) if vehicle speed is above 3 mph (5 km/h). It is recommended that a s[...]

• LOW RANGE – momentarily illuminates when the ignition is turned to the ON position. Illuminates when 4L (4x4 Low) is engaged. Using a Manual Shift On Stop (MSOS) 4WD system (if equipped) Note: Some noise may be heard as the 4WD system shifts or engages. This is normal. 2H (2WD High) – For general on-road driving. Sends power to the rear whe[...]

Shifting from 4H (4WD High) to 2H (2WD High) Move the transfer case lever to 2H (2WD High) at a stop or a vehicle speed below 3 mph (5 km/h). W ith the vehicle at complete stop, disengage the locking hubs (optional) by rotating the hub lock control from LOCK to FREE. • For proper operation, make sure that both indicator arrows on the hub are alig[...]

Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards. This position should only be used when towing the vehicle. Do not leave the vehicle unattended with the transfer case in the N (N[...]

Shifting from 2WD (2WD High) to 4x4 HIGH (4WD High) Rotate the 4WD control to the 4x4 HIGH position at speeds up to 55 mph (88 km/h). • The electronic shift 4WD system is designed to engage 4x4 HIGH (4WD High) when the vehicle is moving. If shifted to 4x4 HIGH (4WD HIGH) while at complete stop, 4x4 may not engage and the 4x4 indicator may not ill[...]

4. Move the 4WD control to the 4x4 LOW position. 5. Hold the shift conditions until the LOW RANGE indicator light illuminates. 6. If the LOW RANGE indicator light does not illuminate within 15 seconds, let the vehicle creep at a speed above 1 mph (1.6 km/h), then repeat steps 3 through 5 before reporting any shift concerns to your authorized dealer[...]

Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Y ou should either know the t[...]

V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]

V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]

Power is supplied to all four wheels through a transfer case. On 4WD vehicles, the transfer case allows you to select 4WD when necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications chapter . Y ou sho[...]

Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even 4WD vehicles can lose traction in slick mud. As when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels. If the vehicle does slide, steer in the direction of the slide until you regain control of the vehicle. If the tran[...]

When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. If you do stall out, do not try to turn around because you might roll over . It is better to back down to a safe location. Apply just e[...]

Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, avoid locking of the wheels. Use a “squeeze” technique, push on the brake pedal with a steadily increasing force which allows the wheels to brake yet continue t[...]

auxiliary horsepower draw , vehicle conditions and surrounding environmental conditions and other factors, this can contribute to elevated transmission fluid temperatures and result in accelerated fluid deterioration, fuel vapor over -pressurization, and other concerns. Ford trucks are fully qualified for stationary PTO operation for 10 minutes or [...]

• The T otal Accessory Reserve Capacity (T ARC) is shown on the lower right side of the vehicle’ s Safety Compliance Certification Label. This applies to Ford-completed vehicles of 10,000 lb. (4,536 kg) GVWR or less. This is the weight of permanently-attached auxiliary equipment, such as snowplow frame-mounting hardware, that can be added to th[...]

certain frontal and offset frontal collisions when the vehicle sustains sufficient longitudinal deceleration. Careless or high speed driving while plowing snow which results in sufficient vehicle decelerations can deploy the airbag. Such driving also increases the risk of accidents. All occupants of the vehicle, including the driver , should always[...]

Do not rock the vehicle if the engine is not at normal operating temperature. Do not rock the vehicle for more than a minute. The transmission and tires may be damaged or the engine may overheat. Refer to T ransmission temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information. Do not spin the wheels at over [...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the New V ehicle Limited W arranty perio[...]

U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. T o obt[...]

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. This switch is located in the front passenger’ s footwell, behind the kick panel access cover . T o reset [...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

T o remove a fuse use the fuse puller tool provided on the fuse panel cover . T o reinstall the cover , align and engage the two hooked clips at the bottom of the cover onto the instrument panel, then lift the panel and press the top clips firmly into place. Always disconnect the battery before servicing high current fuses. Always replace the cover[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A* Adjustable pedals 2 10A* Cluster 3 10A* Upfitter #3 4 20A* Power point (Instrument panel) 5 10A* Upfitter #4 6 — Not used 7 30A* High beam headlamps, Flash-to-pass 8 20A* Back-up lamps 9 — Not used 10 — Not used 11 20A* Radi[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 15 — Not used 16 — Not used 17 15A* Exterior lamps 18 20A* Flasher , Brake On-Off (BOO) lamps 19 10A* Body Security Module (BSM) (Security) 20 15A* T railer tow Electric Brake Controller (EBC) 21 20A* Heated seats 22 20A* Engine control 23 20A* Engine control (gaso[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 40 20A* Fuel pump 41 10A* Instrument cluster 42 15A* Delayed accessory 43 10A* Fog lamps 44 — Not used 45 10A* Ignition switch RUN/ST ART feed 46 10A* Left-hand low beam headlamp 47 10A* Right-hand low beam headlamp 48 — Not used 101 30A** T railer tow EBC 102 30A*[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 304 — Not used 305 Full ISO relay Upfitter control 306 Full ISO relay Delayed accessory 307 Full ISO relay Starter 601 30A circuit breaker Delayed accessory , Power windows, Moonroof 602 — Not used * Mini fuse ** Cartridge fuse Power distribution box The power dist[...]

The high-current fuses and relays are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 30A* W ipers 2 40A* Blower 3 30A* Electronic Shift on the Fly (ESOF) 4 — Not used 5 50A* Injector Driver Module (IDM) (Diesel engine only) 6 — Not used 7 30A* Horizontal Fuel Conditioner Module (HFCM) (Diesel engine o[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 14 — Not used 15 15A** IDM logic (Diesel engine only) 16 — Not used 17 10A** A/C clutch 18 10A** IDM relay (Diesel engine only) 19 — Not used 20 10A** T railer tow back-up lamps 21 — Not used 22 60A*** ABS (Coils) 23 60A*** ABS (Pump) 201 1 ⁄ 2 ISO relay T railer tow r[...]

T emporary Emergency Spare Tire Information Y our vehicle may be equipped with a temporary emergency spare tire. This tire may be a T -type/mini-spare tire which will have the words “T emporary Use Only” molded into the tire sidewall or it may be a full size dissimilar spare tire/wheel that is different in brand, size or appearance from the roa[...]

Dissimilar spare tire/wheel information (if equipped) Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance[...]

Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools, refer to the following table for their locations: T ool Location Spare tire (pick-up trucks only) Under the vehicle, just forward of the rear bumper Jack Regular cab, Super Cab without rear bench seat and Crew Cab: Fastened to floor pan be[...]

• V ehicles equipped with dual rear wheels, insert the lug wrench extension into the lug wrench to reach the lug nuts. 2. Attach the spare tire lock key (A) to the jack handle (B). 3. Fully insert the jack handle through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. Some resist[...]

Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake. • Automatic transmission: Place gearshift lever in P (Park). • Manual transmission: Place gearshift lever in R (Reverse). • Electronic Shift-On-the-Fly (ESOF) 4WD: Place transfer case in any position. • Manual shift transfer case 4WD: Place[...]

If the vehicle slips off the jack, you or someone else could be seriously injured. The following steps apply to F–250/F–350 Single Rear Wheel (SR W) vehicles only (unless otherwise noted): 6. Insert the hooked end of the jack handle into the jack and use the handle to slide the jack under the vehicle. 7. Position the jack according to the follo[...]

• Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle. • Rear (including F-350 Dual Rear wheel [DRW] vehicles) Never use the front or rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body unde[...]

10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front wheels and single rear wheel vehicles. If replacing an inboard rear tire on dual rear wheel vehicles, the valve stem must be facing outward. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the[...]

• Front driver side (4x4): F–350 DRW Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing. • Front passenger side (4x4): F-350 DRW Note: View shown from the rear of the vehicle to clearly identify the jack point. Note: Place the jack directly under axle and inboard of the radius arm so that the jac[...]

• Rear: F-450/F-550 14. Insert the jack handle into the pump linkage. 15. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’ s rated capacity . 16. Remove the lug nuts with the lug wrench. 17. R[...]

The following steps apply to all vehicles: 19. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 8–lug nut torque sequence 10–lug nut torque sequence 20. Stow the flat tire. Refer to Stowing the spare tire if the vehi[...]

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the direction specified on the T ire Changing Instructions located with the jack hardware. 2. Slide the wheel partially under the vehicle and install th[...]

Bolt size Wheel lug nut torque* lb.ft. N • m M14 x 1.5 150 200 * T orque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel[...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fu[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 226[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the bat[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift On 4x4 vehi[...]

Note: T owing an a 4x2 or an ESOF 4WD vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph (56 km/h) may cause damage to the automatic transmission. Note: On Dual Rear Wheel (DRW) vehicles, an outer rear wheel must be removed prior to using a wheel lift wrecker . If the vehicle is towed by other means[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to t[...]

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change elig[...]

Board membership The Board consists of: • Three consumer representatives • An authorized dealer representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The authorized dealer Board member is chosen from an authorized dealer management, recognized for their business leadership qualities[...]

Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well. [...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Can[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSISTAN[...]

ORDERING ADDITIONAL OWNER ’ S LITERATURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: [...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]

racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Y our authorized dealer has touch-up paint and sprays to match your vehicle’ s color . T ake your color code (printed on a sticker in the driver’ s door jamb) to your authorized dealer to ensure[...]

• Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. • Cover the highlighted areas to prevent water damage when cleaning the engine. • 5.4L V8 gasoline engine • 6.8L V10 gasoline engine 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Cleaning 243[...]

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and si[...]

• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then dry by wiping with a dry , soft, clean cloth. • Do not use househol[...]

• Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber , vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear , protective coating on the seat. Note: In some instances, color or dye transfer can occur when wet clothing comes in conta[...]

Conditioning Bottles of King Ranch Leather Conditioner are available at the King Ranch Saddle Shop. Visit the W eb site at www.krsaddleshop.com ,o r telephone (in the United States) 1–800–282–KING (5464). If you are unable to obtain King Ranch Leather Conditioner , use another premium leather conditioner . • Apply your first conditioning tr[...]

Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail W ash (ZC-3–A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.S only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft One Step W ash and W ax Concentrate (ZC-6-A) Mo[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Ch[...]

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engi[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8 gasoline engines Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 1. T ransmission fluid dipstick (automatic transmission) 2. Air filter assembly 3. Engine coolant reservoir 4. Brake fluid reservoir 5. Clutch[...]

6.8L V10 gasoline engine Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 1. T ransmission fluid dipstick (automatic transmission) 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Clutch fluid reservoir (manual transmission) 5. Power distribution box 6. Powe[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent-type fluid or bug wash as this may cause a squeaking/chattering noise[...]

4. Poor wiper quality can be improved by cleaning the wiper blades and the windshield; refer to Windows and wiper blades in the Cleaning chapter . 5. T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro [...]

• 5.4L V8 engine • 6.8L V10 engine 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 255[...]

6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some o[...]

Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the Internati[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance information for the service interval schedules. Keep the electro[...]

Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery , excessive pressure on the end wa[...]

• The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the[...]

• All engines When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to the scheduled maintenance information for service interval schedules.[...]

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see throug[...]

T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly . 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth aroun[...]

Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in this section. If your vehicle is equipped with a diesel engine, refer to the Refill capacities section of your 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement . Fill your engine coolant reser[...]

What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works If the engine begins to ove[...]

Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible. FUEL FILTER For fuel filter replacement, see you[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would h[...]

If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

• Y our Service engine soon indicator may come on. For more information on the Service engine soon indicator , refer to the Instrument cluster chapter . ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver . Y ou must gather information as accurately and consistently as[...]

• Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters[...]

• Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy . • Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy . • W armi[...]

• Four -wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. • Close windows for high speed driving. EP A window sticker Every new vehicle should have the EP A window sticker . Contact your authorized dealer if the window sticker is not supplied with your vehicle. The EP A window sticker should be your guid[...]

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove [...]

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your Check engine/Service engine soon light is on, refer to the description in the W arning lights and chimes section of the Instrument Cluster chapter . Y our vehicle may not pass the I/M t[...]

Check the fluid level when it is at ambient temperature, 20°F–80°F (-7°C–25°C): 1. Check the fluid level on the dipstick. It should be between the arrows in the FULL COLD range. Do not add fluid if the level is within this range. 2. If the fluid level is low . Add fluid to bring fluid level up to be between the arrows in the FULL COLD range[...]

Use only a DOT 3 brake fluid designed to meet Ford specification ESA-M6C25–A. Refer to Lubricant Specifications in this chapter . Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. If taken internally , drink water and induce vomiting. Seek medical a[...]

3. W ith the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary[...]

High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correc[...]

Automatic transmission fluid filter (if equipped) The T orqShift automatic transmission is equipped with a serviceable external fluid filter mounted on the frame rail. Refer to the scheduled maintenance information for service intervals. T o replace the transmission filter: 1. Shut off the engine. 2. Unscrew filter housing. 3. Replace filter with a[...]

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Us[...]

CHECKING AND ADDING TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter . DRIVELI[...]

Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element • 5.4L Engine 1. Release two retainer clamps. 2. Pull air filter tray assembly out toward front of vehicle and lift air filter element up and out of housing. The air filter box needs to be free of any debri[...]

1. Loosen the clamps that secures the air filter cover in place. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. 5. Reassemble the two halves of the air filter housing, aligning the notchs and slots. Secure the clamps, making sure not [...]

MOTORCRAFT PART NUMBERS Component 5.4L V8 engine 6.8L V10 engine Air filter element F A-1754 F A-1782 Fuel filter FG-1011 FG-1011 Oil filter FL-820-S FL-820-S PCV valve 1 Battery (Standard) BXT -65-650 BXT -65-650 Battery (Optional) BXT -65-750 BXT -65-750 Spark plugs-platinum 2 Remote Automatic T ransmission Filter 3 FT -145 FT–145 1 The PCV val[...]

REFILL CAPACITIES Fluid Ford Part Name Application Capacity Front axle Motorcraft SAE 80W -90 Premium Rear Axle Lubricant F-250/350 (Dana 60 axle) 6.3 pints (3.0L) F-350/450/550 (Dana 60 axle) 6.3 pints (3.0L) Rear axle Motorcraft SAE 75W -140 Synthetic Rear Axle Lubricant F-250 /350 (10.50 inch axle) 1 6.9 pints (3.3L) Motorcraft SAE 75W -90 Synth[...]

Fluid Ford Part Name Application Capacity Engine oil (includes filter change) - gas engines 6 Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 5.4L V8 and 6.8L V10 engines 7.0 quarts (6.6L) Engine oil (includes filter change) - diesel engine Refer to your 6.0 Liter Power Stroke Dire[...]

Fluid Ford Part Name Application Capacity Automatic transmission fluid 3 Motorcraft MERCON 威 SP AT F T orqShift (5–speed) 17.5 quarts (16.6L) 5 (includes remote filter element change) W indshield washer fluid Motorcraft Premium W indshield W asher Concentrate All 4.25 quarts (4.0L) 1 Add 8 oz. (236 ml) of Additive Friction Modifier XL-3 or equi[...]

6 Use of synthetic or synthetic blend motor oil is not mandatory . Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark. LUBRICANT SPECIFICATIONS Item Ford part name or equivalent Ford part number Ford specification Spindle bearing High T emperature 4X4 Front Axle and Wheel Bearing Grease E8TZ[...]

Item Ford part name or equivalent Ford part number Ford specification Brake fluid and clutch fluid (if equipped) Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1 ESA-M6C25-A or WSS-M6C62-A Engine coolant Motorcraft Premium Gold Engine Coolant (yellow-colored) VC-7-A (U.S., except CA, OR and NM), VC-7-B (CA, OR and NM) WSS-M97B51-A1[...]

Item Ford part name or equivalent Ford part number Ford specification T ransmission /parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Motorcraft Premium Long-Life Grease XG-1-C or XG-1-K ESA-M1C75-B Steering linkage, knuckle ball joints (F-450/550) and trackbar ball joint (F-450/550) Motorcraft Premium Long-Life Grease [...]

slip axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water . Dana rear axles also contain a synthetic lubricant but do require a change. Refer to your scheduled maintenance information for change intervals on Dana rear axles. 2 Ensure the correct automatic transmission[...]

V EHICLE DIMENSIONS F–250 Regular Cab and SuperCab Dimension Body style Regular Cab 4x2 – inches (mm) Regular Cab 4x4 – inches (mm) SuperCab 4x2 – inches (mm) SuperCab 4x4 – inches (mm) (1) Overall height 76.5 (1943) 79.1 (2009) 76.8 (1951) b 79.4 (2017) b (2) T rack - Front/Rear 68.3 (1734)/67.2 (1706) 68.3 (1736) / 67.2 (1706) 68.3 (173[...]

Dimension Body style Crew Cab 4x2, Short box - inches (mm) Crew Cab 4x4, Short box - inches (mm) Crew Cab 4x2, Long box - inches (mm) Crew Cab 4x4, Long box - inches (mm) (2) T rack - Front/Rear 68.3 (1734)/ 67.2 (1706) 68.3 (1736)/ 67.2 (1706) 68.3 (1734)/ 67.2 (1706) 68.3 (1736)/ 67.2 (1706) (3) Overall width 79.9 (2029) 79.9 (2029) 79.9 (2029) 7[...]

Dimension Body style Regular Cab Chassis Cab - inches (mm) SuperCab Chassis Cab - inches (mm) Regular Cab Style Side - inches (mm) SuperCab Style Side - inches (mm) (2a) T rack - Front 68.3 (1734) a / 68.9 (1751) b / 68.3 (1736) c / 69.0 (1753) d 68.3 (1734) a / 68.9 (1751) b / 68.3 (1736) c / 69.0 (1753) d 68.3 (1734) a / 68.9 (1751) b / 68.3 (173[...]

F–350 Crew Cab Dimension Body style Crew Cab Chassis Cab - inches (mm) Crew Cab, Short box - inches (mm) Crew Cab, Long box - inches (mm) (1) Overall height 77.9 (1979) a / 77.9 (1979) b / 81.8 (2078) c / 80.8 (2052) d 77.8 (1976) a / 77.6 (1971) b / 81.8 (2078) c / 80.1 (2035) d 77.6 (1971) a / 77.4 (1966) b / 81.7 (2075) c / 80.0 (2032) d (2a) [...]

F–450 Dimension Body style Regular Cab Chassis 4x2 – inches (mm) Regular Cab Chassis 4x4 – inches (mm) SuperCab Chassis 4x2/4x4 – inches (mm) Crew Cab Chassis 4x2/4x4 – inches (mm) (1) Overall height 80.6 (2047) a 80.5 (2045) b,c 80.2 (2037) d 80.7 (2050) a 80.5 (2045) b 80.0 (2032) c,d 80.5 (2045) 80.8 (2052) - 4x2 80.9 (2055) - 4x4 (2) [...]

F–550 Dimension Body style Regular Cab Chassis Cab 4x2 – inches (mm) Regular Cab Chassis Cab 4x4 – inches (mm) Crew Cab Chassis Cab 4x2 – inches (mm) Crew Cab Chassis Cab 4x4 – inches (mm) (1) Overall height 81.7 (2075) a 81.4 (2068) b,c 81.1 (2060) d 81.7 (2075) a 81.2 (2062) b 81.1 (2060) c 80.7 (2050) d 81.5 (2070) 81.4 (2068) (2) T ra[...]

2 3 1 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 300[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

1. W orld manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmiss[...]

Code Description 5 Six-speed manual, Dana (ZF S6–650) 7 Six-speed manual, Dana (ZF M6HD-W) T Five-speed automatic, T orqShift (gas engines) B Five-speed automatic, T orqShift (diesel engine) 2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 303[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada authorized dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic [...]

T onneau covers Wheels Interior style Electrochromatic compass/temperature interior mirrors Floor mats Speed control Lifestyle Bedliners and bedmats Bed tents Bike racks Sport Liner 娂 T oolboxes T owing mirrors T railer hitches, wiring harnesses and accessories Peace of mind First aid and highway safety kits Full vehicle covers Keyless entry Lock[...]

theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by your authorized dealer . • Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use. • T [...]

A Accessory delay .......................... 57 Air cleaner filter ....... 283–284, 286 Air conditioning .......................... 36 Airbag supplemental restraint system ................................ 107–108 and child safety seats ............ 109 description .............................. 108 disposal .................................... [...]

wheels ...................................... 242 wiper blades ............................ 244 Climate control (see Air conditioning or Heating) ............36 Clutch fluid .......................................... 277 operation while driving ..........178 recommended shift speeds .... 179 Compass, electronic set zone adjustment .................[...]

filter , specifications ........257, 286 recommendations ................... 257 refill capacities ........................ 287 specifications .......................... 290 Exhaust fumes .......................... 169 F Fail safe cooling ........................ 265 Fluid capacities ......................... 287 Foglamps ..........................[...]

K Keyless entry system ................. 86 Keys positions of the ignition ......... 165 L Lamps autolamp system ....................... 39 daytime running light ...............40 fog lamps ................................... 40 headlamps ................................. 39 headlamps, flash to pass .......... 41 instrument panel, dimming ..... 41 [...]

R Radio ..........................20, 22, 25, 28 Relays ........................................ 203 Remote entry system ................. 82 illuminated entry ...................... 85 locking/unlocking doors ........... 80 Reverse sensing system ........... 181 Roadside assistance .................. 201 S Safety Belt Maintenance ..........107 Saf[...]

T railer Brake Controller -Integrated ................ 157 T ransfer case fluid checking ......................... 283 T ransmission automatic operation ......... 55, 174 brake-shift interlock (BSI) .... 174 fluid, checking and adding (automatic) ............................. 278 fluid, checking and adding (manual) .................................[...]