Go to page of
Similar user manuals
-
Barcode readers
Honeywell Solaris 7820
64 pages -
Scanner
Honeywell MS7820
2 pages 0.15 mb -
Home Security System
Honeywell VISTA250BPT/
80 pages 0.9 mb -
Scanner
Honeywell 3820
22 pages 0.22 mb -
Home Gym
Honeywell 4800i
250 pages 2.81 mb -
Thermostat
Honeywell THR870CUK
19 pages 4.18 mb -
Thermostat
Honeywell CT1950
2 pages 0.31 mb -
Water Dispenser
Honeywell F74C
8 pages 0.63 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Honeywell FLASHGUARD 2000B, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Honeywell FLASHGUARD 2000B one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Honeywell FLASHGUARD 2000B. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Honeywell FLASHGUARD 2000B should contain:
- informations concerning technical data of Honeywell FLASHGUARD 2000B
- name of the manufacturer and a year of construction of the Honeywell FLASHGUARD 2000B item
- rules of operation, control and maintenance of the Honeywell FLASHGUARD 2000B item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Honeywell FLASHGUARD 2000B alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Honeywell FLASHGUARD 2000B, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Honeywell service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Honeywell FLASHGUARD 2000B.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Honeywell FLASHGUARD 2000B item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
FlashGuard 2000B Medium Intensity Lighting System Troubleshooting Guide Table of Contents Flashhead (Strobe) Troubleshooting Flowchart pg. 2 Multiple Strobe Troubleshooting Flowchart pg. 3 Flashhead Problems pg. 4 Multiple Strobe Problems pg. 7 Flashhead Isolation Test pg. 9 Power Supply Isolation Test pg. 10 Status Indicators pg. 11 Tools Required[...]
-
Page 2
FlashGuard 2000B Troubleshooting Guide Page 2 Flashhead (Strobe) Problems START Flashhead works in at least one mode? No Are all of the LEDs OFF? Control Power ON, High Voltage OFF? No Control Power and High Voltage Both ON ? No Yes Day mode strobe is OK, Night strobe out? Section 1, pg. 4 Yes Yes Yes Section 2, pg. 4 Section 3, pg. 5 Yes Section 4[...]
-
Page 3
FlashGuard 2000B Troubleshooting Guide Page 3 Multiple Strobe Problems . No Strobes are flashing out of sync. Yes Section 9, pg. 8 No Strobes have a ‘double flash’ or are flashing faster than 40 FPM? Yes Section 10, pg. 8 Master switches to night, but slaves stay in day mode? Yes Section 11, pg. 8 START Only one strobe is acting unusual? No Yes[...]
-
Page 4
FlashGuard 2000B Troubleshooting Guide Page 4 FLASHHEAD (STROBE) PROBLEMS Section 1 Flashhead does not operate in any mode, no LED’s on. Possible Cause : Input power incorrect. Diagnostic Test : Measure input power – it should be 120 VAC ±10%. Corrective Action: Supply correct input power. Possible Cause : Power supply interlock switch not eng[...]
-
Page 5
FlashGuard 2000B Troubleshooting Guide Page 5 Section 3 Flashhead will not operate in any mode. Control power indicator on, high-voltage board LED indicator on. Possible Cause : Trigger control board defective, or incorrect DIP switch setting. Diagnostic Test : Perform “Flashhead Isolation Test” (pg. 9) and “Power Supply Isolation Test” (pg[...]
-
Page 6
FlashGuard 2000B Troubleshooting Guide Page 6 Possible Cause : Day capacitor/s or 20 Ω resistors faulty, or connection loose/open. Diagnostic Test : With all conductors attached, check resistance across the terminals of any C2 capacitor. Resistance should be @ 40 Ω Ω . Corrective Actions: 1. If resistance is near 0 Ω Ω , one or more C2 ca[...]
-
Page 7
FlashGuard 2000B Troubleshooting Guide Page 7 Section 7 Flashhead flashing slow (15 – 20 flashes per minute), strobe alarm on. Possible Cause : Mis-configured or defective sync monitor board. Diagnostic Test: Ensure the DIP switches on the sync monitor board are set correctly per the manual. Visually verify that the red LED on the sync monitor bo[...]
-
Page 8
FlashGuard 2000B Troubleshooting Guide Page 8 Section 10 All lights are in sync, but there is a double-flash, or flashing faster than 40 flashes per minute (fpm). Possible Cause : More than one sync monitor board is set as master. Diagnostic Test: Inspect the DIP switches on each sync monitor board. In the master power supply, DIP switch S1-4 shoul[...]
-
Page 9
FlashGuard 2000B Troubleshooting Guide Page 9 Flashhead Isolation Test Disconnect the seven conductor cable from power supply at terminal block TB2. Using an Ohmmeter, check the resistance between the conductors of the disconnected flashhead cable, and compare to the expected values: FG 2000B White Strobe (cable disconnected from power supply) #1 R[...]
-
Page 10
FlashGuard 2000B Troubleshooting Guide Page 10 Power Supply Isolation Test Leave the seven conductor strobe cable disconnected from the power supply at terminal block TB2. Install a jumper wire between terminals 5 and 6 to simulate the interlock switch being depressed. Install a neon lamp (Radio Shack catalog # 272-1102, Honeywell Part # 77-2342) a[...]
-
Page 11
FlashGuard 2000B Troubleshooting Guide Page 11 Status Indicators Control Power ON • Located on the control panel (top center), this indicator is illuminated whenever input power is present and the power supply interlock switch is engaged. High Voltage Neon Lamp • Located on the high voltage circuit (top) board, this lamp indicates that the high[...]
-
Page 12
FlashGuard 2000B Troubleshooting Guide Page 12 Recommended Spare Parts Flashhead Spares (Upstairs) Part Number Description 12S00602 Flashtube Assembly: FT1 77-4040K Trigger Transformer: T1 77-2644 Switch, Interlock, S1 Power Supply Spares (Downstairs) Part Number Description 77-3911 Night Capacitor: C3 CA706A441EK Day Capacitors: C2 (A-F) 77-1167 6[...]
-
Page 13
FlashGuard 2000B Troubleshooting Guide Page 13[...]