English dropdown-ico

IBM 8173 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of IBM 8173, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of IBM 8173 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of IBM 8173. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of IBM 8173 should contain:
- informations concerning technical data of IBM 8173
- name of the manufacturer and a year of construction of the IBM 8173 item
- rules of operation, control and maintenance of the IBM 8173 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of IBM 8173 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of IBM 8173, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the IBM service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of IBM 8173.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the IBM 8173 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    ThinkC e n tr e ™ Hard w are Remo v a l an d Rep l ac e m ent Gu i d e Ty p e s 84 2 4 , 84 2 5 , 84 2 8 Ty p e s 81 7 1 , 81 7 2 , 81 7 3 [...]

  • Page 2

    [...]

  • Page 3

    ThinkC e n tr e ™ Hard w are Remo v a l an d Rep l ac e m ent Gu i d e Ty p e s 84 2 4 , 84 2 5 , 84 2 8 Ty p e s 81 7 1 , 81 7 2 , 81 7 3 [...]

  • Page 4

    Second Edition (June 2004) © Copyright International Business Machines Corporation 2004. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.[...]

  • Page 5

    Contents Overview . . . . . . . . . . . . . .v Safety information . . . . . . . . . . . .v Additional information resour ces . . . . . . .v T ools requir ed . . . . . . . . . . . . . .v Handling static-sensitive devices . . . . . . .v Replacing customer replaceable units (CRUs) . . . . . . . . . . . . . . .1 Opening the cover . . . . . . . . . . . [...]

  • Page 6

    iv Hardwar e Removal and Replacement Guide[...]

  • Page 7

    Overview This guide contains instructions for replacing the following customer replacement units (CRUs): v Power supply v System board v Micropr ocessor v Hard disk drive v Memory modules Safety information Do not open your computer or attempt any repair before reading the “Important safety information” in the Quick Reference that was included [...]

  • Page 8

    v Before you replace a new CRU, touch the static-protective package containing the CRU to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body . v When possible, remove the new CRU from the static-protective packaging, and install it dire[...]

  • Page 9

    Replacing customer replaceable units (CRUs) Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . Openi[...]

  • Page 10

    Locating components The following illustration will help you locate the various components in your computer . 1 Diskette drive lock 5 Power supply assembly 2 Memory modules 6 CD or DVD drive (hard disk drive is under the CD drive) 3 Battery 7 CD or DVD drive lock 4 PCI riser 2 Hardwar e Removal and Replacem[...]

  • Page 11

    Identifying parts on the system board The system board (sometimes called the planar or motherboard ) is the main circuit board in your computer . It provides basic computer functions and supports a variety of devices. The following illustration shows the locations of parts on the system board. 1 Fan connectors (2) 8 Diskette drive conne[...]

  • Page 12

    2. Pivot the drive bay assembly upward to gain access to the cable connections. 3. Locate the power supply . See “Locating components” on page 2. Note: Note the routing of the power supply cables. It is important to route the cables the same way when installing a new power supply assembly . 4. Disconnect the power cables from the hard disk driv[...]

  • Page 13

    7. Remove the screws at the rear of the chassis that secure the power supply . 8. Slide the power supply forward and remove from the computer . Replacing customer replaceable units (CRUs) 5[...]

  • Page 14

    9. Install the new power supply into the chassis so that the screw holes in the power supply align with those in the chassis. Note: Use only the screws provided by IBM. 10. Install and tighten the four screws at the rear of the chassis that secure the power supply . 11 . Reconnect the speaker wire to the system board. 12. Reconnect power supply con[...]

  • Page 15

    Removing and replacing the system board assembly Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . [...]

  • Page 16

    installed. 5. Carefully note the location of all cable connections on the system board. It will be necessary to reconnect them properly after installing the new system board assembly . Note: Note the cable routing. It is important to route the cables the same way when installing a new system board. 6. Disconnect the diskette drive cable from the sy[...]

  • Page 17

    10. Using the two blue handles provided, lift the system board assembly out of the computer . 11 . Place the old system board next to the new system board on a clean, flat surface. 12. Remove the micropr ocessor from the old system board. Go to “Removing and replacing the micropr ocessor” on page 10. Return here after removing the micropr ocess[...]

  • Page 18

    Removing and replacing the microprocessor Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . Importa[...]

  • Page 19

    4. Release the lever 1 holding the micropr ocessor heat sink. 5. Remove the heat sink, and do one of the following: v If you are replacing the micropr ocessor , place the old heat sink aside. Yo u must use the new heat sink shipped with the new micropr ocessor . Note Do not use the old heat sink with the a new micropr ocessor . If you use the[...]

  • Page 20

    Notes: a. Notice of the orientation of the notches 1 on the micropr ocessor . This is important when reinstalling the micropr ocessor on the system board. * XXXXXXXXX* b. Do not drop anything on the socket while it is open. Keep all contacts as clean as possible. 7. To install the micropr ocessor , do one of the following: Attention To avoid [...]

  • Page 21

    b. Remove the new micropr ocessor from its static-protective package. * XXXXXXXXX* c. Hold the micropr ocessor 2 by its sides and loosen the black cover 3 on the micropr ocessor , but do not remove the black cover . d. Place the micropr ocessor on the static-protective package. e. Use the vacuum pen 1 to pick up the new micropr oc[...]

  • Page 22

    b. Install the micropr ocessor by inserting it straight down into the socket of the new system board. 8. Pivot the retaining plate 1 closed, and lock the lever 3 to secure the micropr ocessor 2 in place. Be sure to engage the retainer tab when locking the micropr ocessor . *XXXXXXXXX* 9. Do one of the following: v If you have repl[...]

  • Page 23

    Removing and replacing memory modules Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . To remove a[...]

  • Page 24

    installed. 4. Locate the memory connectors. See “Locating components” on page 2. 5. Open the retaining clips, and lift the memory module out of its connector . 6. Insert the replacement memory module in the memory connector . Ensure the notch on the replacement memory module 1 aligns correctly with the connector key 2 on the system [...]

  • Page 25

    7. Reinstall the PCI riser and adapters if they were removed. 8. Pivot the drive bay assembly back to the original position. 9. Close the cover and reconnect the external cables . Go to “Completing the installation” on page 19. Replacing customer replaceable units (CRUs) 17[...]

  • Page 26

    Removing and replacing a hard disk drive Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . 1. Open [...]

  • Page 27

    6. Remove the old hard disk drive from the blue bracket by flexing the bracket. Do not touch the circuits 5 on the hard disk drive. 7. Insert the new hard disk drive into the blue bracket aligning the pins 1 through 4 on the bracket with the holes in the hard disk drive. 8. Insert the hard disk drive into hard disk bay with the ci[...]

  • Page 28

    Attention Keep cables 1 through 3 clear of the hinges and sides of the computer chassis. 3. Make sure that the drive locks on the drive bay assembly are both in the locked position . Otherwise, you cannot close the cover . 4. Close the cover . 5. If a cover lock is installed, lock the cover . 6. If your computer is being placed in the v[...]

  • Page 29

    7. Reconnect the external cables. Plug the power cord into the computer then into a properly grounded power receptacle. 1 Power cord connector 9 Parallel connector 2 Cable lock latch 10 Audio line-in connector 3 Rope clip (U-bolt) holes 11 Audio line-out connector 4 PCI and PCI express adapter slots 12?[...]

  • Page 30

    3. When you are prompted to select a language, press the number on your keyboard which corresponds to the language then press Enter . 4. When prompted to change the serial number , press Y. 5. T ype in the seven character serial number of your computer then press Enter . 6. When prompted to change the machine type/model, press Y. 7. T ype in the se[...]

  • Page 31

    [...]

  • Page 32

     Part Number: 19R0821 Printed in USA (1P) P/N: 19R0821[...]