English dropdown-ico

Pelco SX8205R manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco SX8205R, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco SX8205R one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco SX8205R. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco SX8205R should contain:
- informations concerning technical data of Pelco SX8205R
- name of the manufacturer and a year of construction of the Pelco SX8205R item
- rules of operation, control and maintenance of the Pelco SX8205R item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco SX8205R alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco SX8205R, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco SX8205R.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco SX8205R item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    ® INST ALLA TION SX8205R Unmanaged Ethernet Switch Five 10BASE-T/100BASE-TX Ports C2626M (2/07)[...]

  • Page 2

    2 C2626M (2/07) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Not ices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . [...]

  • Page 3

    C2626M (2/0 7) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Inst all in accordance with the manufacturer’ s instructions. 8. Do not install n[...]

  • Page 4

    4 C2626M (2/07) The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NO[...]

  • Page 5

    C2626M (2/0 7) 5 Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation. RADIO AND TELEVIS ION INTERFERENCE [...]

  • Page 6

    6 C2626M (2/07) Product Overview DESCRIPTION The SX8205R unmanaged Ethernet switch provides five 10B ASE-T/100BASE-TX ports for the transport of bidirectional Ethernet data. Operating as a single switch in a net work, the SX8205R module connects to up to five 10BASE-T/100BASE-TX Ether net devices. If a larger switched network is needed, multiple SX[...]

  • Page 7

    C2626M (2/0 7) 7 • Compliant with IEEE 802.3, 802.3u, and 802.3x standards • 10BASE-T/100BASE-TX compat ibility with all Pelco ® and third-pa rty 10BASE-T/100BASE-TX Ethernet devices • Environmentally hardened • Designed to meet NEMA TS 2 and Caltrans traff ic signal control equipment standards for ambient operating temperature, mechanical[...]

  • Page 8

    8 C2626M (2/07) FRONT PANEL Figure 2 illustrates the front panel of the SX8205R module. Figure 2. Front Panel of SX8205R Module ì Reset Button: Restarts the un it î Power LED: Pelco badge NOTE: For additional information ab out the Power LED, refer to T roubleshooting on page 15.[...]

  • Page 9

    C2626M (2/0 7) 9 REAR PANEL Figure 3 illustrates the rear panel of the SX8205R module. Figure 3. Rear Panel of SX8205R Module For additional information about r ear -panel connections, refer to Installation on page 10. For detailed information about the RJ-45 LEDs, refer to T roubleshooting on page 15. ì Rack Power/Alarm Connector: 4-pin connector[...]

  • Page 10

    10 C2626M (2/07) Installation PACKAGE CONTENTS The following it ems are supplied: 1 SX8205R module 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K., and European configurations); 100-240 V A C, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4 - 40 x 0.250-inch Phillips pa n head screws with lock wa [...]

  • Page 11

    C2626M (2/0 7) 11 Using the TX Mode switch for a parti cular port, y ou can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotiation allows the SX8205R module to automatically negotiate with the device to which the port is connected fo r data rate and duplex modes of operation[...]

  • Page 12

    12 C2626M (2/07) NOTE: TX Mode configuration must be set when the module is powered off. If you wish to change a TX Mode switch setting after the module has been powered on, power of f the module, change the TX Mode switch setting, and then power on the module again. MOUNTING The SX8205R module can be mounted into a rack or can be used as a stand-a[...]

  • Page 13

    C2626M (2/0 7) 13 Mounting the SX8205R Module Using the W all Clip NOTE: Before mounting the SX8205R module to a wall, ensure that there is adequate space at both ends for viewing the front-panel Pow er LED and for making the various rear -panel cable connections. T o attach the SX8205R module to a wall using the supplied wall clip, refer to Figure[...]

  • Page 14

    14 C2626M (2/07) CONNECTIONS Connections to the SX8205R module are made on the rear panel of the module (refer to Figure 6). Figure 6. SX8205R Module Co nnections As illustrated in Figure 6, SX8205R module connections consist of the following: • Power connection NOTES: – A 12 VDC or 24 VA C power supply can be us ed to power the module when use[...]

  • Page 15

    C2626M (2/0 7) 15 T roubleshooting LED indicators on the front and rear panels of the SX8205R module allow you to monitor operational status: • The Power LED (Pelco badge) on t he front panel (refer to Figure 2) allows you to monitor operating power . Refer to T able B for info rmation about the Power LED and associated troubleshooting guidelines[...]

  • Page 16

    16 C2626M (2/07) T able C. T roubleshooting with Rear -Panel Indicators Indicator Color Meaning Possible Cause Corrective Action RJ-45 10BASE-T/100BASE-TX Port Stat us LED - Left (Link / Activity) Amber A 10BASE-T link is established. — If 10BASE-T operation is desired, no action is required. If 10BASE-T operation is not desired, refer to Setting[...]

  • Page 17

    C2626M (2/0 7) 17 RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued) Not lit A 10BASE-T or 100BASE-TX link cannot be established. A problem may exist with the cable: • Cable is not connected to the module or to the 10BASE-T/100BASE-TX compatible device. • Cable is defective. • Cable is not the proper cable type. • [...]

  • Page 18

    18 C2626M (2/07) RJ-45 10BASE-T/100BASE-TX Port St atus LED - Right (Duplex/Collision) Amber Port is set to 10BASE-T full- duplex mode. — If 10BASE-T full-duplex operation is desired, no action is required. If 10BASE-T full- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 10 for information. F[...]

  • Page 19

    C2626M (2/0 7) 19 RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Green Port is set to 100BASE-TX full- duplex mode. — If 100BASE-TX full-duplex operation is desired, no action is required. If 100BASE-TX full- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 10[...]

  • Page 20

    20 C2626M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Not lit Port is set to 10BASE-T half- duplex mode and no collisions are detected.* — If 10BASE-T half-duplex operation is desired, no action is required. If 10BASE-T half- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Mo[...]

  • Page 21

    C2626M (2/0 7) 21 Specifications PERFORMANCE Switch T ype Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.3, 802.3u, 802.3x Interface Auto MDI/MDI-X Operating Mode Full- duplex or half-duplex Address T able Size 1,024 MAC address ent ries with automatic learning and[...]

  • Page 22

    22 C2626M (2/07) Appendix. RJ-45 Connector Pinouts Figure 7 illustrates RJ-45 MDI/MDI-X connector pinouts. Figure 7. RJ-45 MDI/MDI-X Connector Pinouts T able D summarizes RJ-45 MDI/MDI-X connector pinouts. T able D. RJ-45 MDI/MDI-X Connector Pinouts Pin Number MDI (Normal Mode) MDI-X (Crossed Mode) 1R X + T X + 2R X - T X - 3 TX+ RX+ 4 Not used Not[...]

  • Page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warranty are as noted below: • Five years on fiber o ptic products and TW3 000 Series unshield ed twisted pair tr an[...]

  • Page 24

    ® Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Ara[...]