English dropdown-ico

Smeg CIR34AX manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Smeg CIR34AX, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Smeg CIR34AX one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Smeg CIR34AX. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Smeg CIR34AX should contain:
- informations concerning technical data of Smeg CIR34AX
- name of the manufacturer and a year of construction of the Smeg CIR34AX item
- rules of operation, control and maintenance of the Smeg CIR34AX item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Smeg CIR34AX alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Smeg CIR34AX, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Smeg service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Smeg CIR34AX.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Smeg CIR34AX item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Contents 3 1 INSTRUCTIONS FOR SAFE AND PROPER USE _____________________ 4 2 POSITIONING OF THE HOB _____________________________________ 6 3 GAS CONNE CTION ___________________________________________ 11 4 ELECTRICAL CONNECTION ____________________________________ 12 5 ADAPTATION TO DIFFERENT TYPES OF GAS _____________________ 13 6 FINAL OPERATIONS[...]

  • Page 2

    Introduction 4 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WH OLE WORKING LIFE OF THE COOKING HOB. WE ADVISE R EADING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEF ORE USING THE COOKING HOB. ALSO KEEP THE SERIES OF NOZZLES SU[...]

  • Page 3

    Introduction 5 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECTLY SMO[...]

  • Page 4

    Instructions for the installer 6 2 POSITIONING OF THE HOB It is the law that all gas a ppliances are installed by authorised persons . Clearance aro und the appliance must comply with the requirem ents of AS5601. The following operati on requires build ing and/or carpentry work so m ust be carried out by a competent tradesman. Installation can be c[...]

  • Page 5

    Instructions for the installer 7 Bracket ‘ A ’ in the 1st slot Bracket ‘ A ’ in the 2nd slot Bracket ‘ B ’ Short sides Long sides 2.2 Fixing 90 cm hobs on 60 cm base unit If a 90 cm hob is to be bracketed to a 60 cm base unit, the 2 central brackets “ A ” have to be used in ad dition to the side brackets “ B ” as shown in the dr[...]

  • Page 6

    Instructions for the installer 8 Overall dimensions: location of gas and electrical connection points (all measures in mm). 60 cm 90 cm hob hob A 35 105 B 65 50 C 30 50 D 85 75 2.3 Clearance above and around domestic appliances Extract from AS5601[...]

  • Page 7

    Instructions for the installer 9 REQUIREMENTS 1 Overhead clearances – (Measurement A ) Range hoods and exha ust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead [...]

  • Page 8

    Instructions for the installer 10 3 For definition of hob, see Claus e 1.4.64. 4 For definition of triv et, see Clause 1.4.109. 5 Consideration is to be given to windo w treatments when located near cooking appli ances. See Clause 5.3.4. 2.4 Room ventilation Caution – This hob may only be installed and operated in rooms permanently ventilated in [...]

  • Page 9

    Instructions for the installer 11 3 GAS CONNECTION This appliance is suitable for installation with Natur al Gas or ULPG (propane). Refer to page 12 for the relevant burner pressure an d appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator su pplied must be fitted to the gas inlet. A test poin[...]

  • Page 10

    Instructions for the installer 12 4 ELECTRICAL CONNECTION Make sure that the voltage and cap acity of the power line conform to the data shown on the plate l ocated under the casing. Do not remove this plate for any reason. The plug o n the end of the supply cable and the wall soc ket must be the same type and conform to the curr ent electrical sys[...]

  • Page 11

    Instructions for the installer 13 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been adjusted for natural gas at a pressure of 1.0 kPa. For functioning with other types of gas the nozzles must be replaced and the primary air adjusted. To replac[...]

  • Page 12

    Instructions for the installer 14 5.2 Removing the hob (models wi th built-in control panel) 1. Remove the knobs, the gri ddles, the burner caps, the flam e caps and the two rear plugs; 2. Remove the screws “A” which fix the burner supports; 3. Raise the hob, sliding it off the ignition plugs and/or the thermocouples and the gas tap rods; 5.3 A[...]

  • Page 13

    Instructions for the installer 15 5.4 Adjustment for natural gas The hob has been adjusted for natural gas at a pressure of 1.0kPa. To allow the unit to work back with this type of gas, after it has been adjusted for ULPG, perform the same operations described in paragraph “5.3 Adjustment for ULPG”, but r efer to the following table for the pro[...]

  • Page 14

    Instructions for the installer 16 6 FINAL OPERATIONS Having carried out the above adjustments, reassemble the ap pliance following, backwards, the instructions i n paragraph “ 5.1 Removing the control panel / 5.2 Removing the ho b”. 6.1 Adjustment of minimum for natural gas Light the burner and take it to the minimum . Remove the gas tap knob a[...]

  • Page 15

    Instructions for the installer 17 6.2 Arrangement of burners on the hob (hobs with separable control panel). 60 cm hobs BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid large 5. Wok 90 cm hobs BURNERS 1. Auxiliary 2. Semirapid 3. Rapid 4. Fish burner 5. Wok[...]

  • Page 16

    Instructions for the installer 18 6.3 Arrangement of burners on the hob (hobs with b uilt- in control panel). 60 cm hobs BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid 5. Wok 6.4 Lubrication of gas taps With time it may happen that the gas taps get blocked and h ard to turn. Clean them inside and r e-grease them. This operation must be[...]

  • Page 17

    Instructions for the user 19 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted cor rectly. In the wok burner, notch A must be aligned with pin B . Grid C provided is intended for use with wok s (Chinese pans). Adapter D comes only with o pen grids models and is intended for us e with sma[...]

  • Page 18

    Instructions for the user 20 7.3 Diameter of containers Burners Ø min. and max . (en cm.) Auxiliary 12-14 Semirapid 16-20 Rapid 22-26 Rapid large 22-26 Wok 22-34 Fish burner Special oval-shaped vessels 7.4 Electric elements 7.4.1 Turning on electric elements Hobs may be fitted with an electric element of various diameter. The electric elem ent is [...]

  • Page 19

    Instructions for the user 21 WARNING When switching on the electric element for the first time, or if the electric element has not been used for a long time, to remove any humi dity from the insulating material it should be dr ied out by placing the electric ele ment on position 1 for 30 minutes. To use correctly remember to: • Switch the electri[...]

  • Page 20

    Instructions for the user 22 8 CLEANING AND MAINTENANCE Before any intervention, disc onnect the power supply of the device. 8.1 Cleaning Clean the cooking top regul arly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean an d preserve the surface, a lways use specific products only, whic[...]

  • Page 21

    Instructions for the user 23 8.2.2 The electric element After use, to make sure that the surf aces are clean and lon g lasting, the electric element must be treated w ith specific cleaning pro ducts which are available on the market. This necessary operation pr events oxidisation (rust formation). 8.2.3 The cover Clean the glass or steel cover, whe[...]

  • Page 22

    Instructions for the user 24 9 PROBLEMS AND CAUSES Each of the following cases is caused by an abnormal operation of the appliance and shoul d be dealt with by a authorised pers ons: please contact your local dealer or Service Center in case yo u detect any of these malfunctioning. PROBLEM CAUSE WHAT TO DO The flame is very lo ng with bright yellow[...]

  • Page 23

    [...]

  • Page 24

    914773237/ B[...]