English dropdown-ico

Stovax ASHDON 8546LUC-P8546LUC manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Stovax ASHDON 8546LUC-P8546LUC, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Stovax ASHDON 8546LUC-P8546LUC one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Stovax ASHDON 8546LUC-P8546LUC. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Stovax ASHDON 8546LUC-P8546LUC should contain:
- informations concerning technical data of Stovax ASHDON 8546LUC-P8546LUC
- name of the manufacturer and a year of construction of the Stovax ASHDON 8546LUC-P8546LUC item
- rules of operation, control and maintenance of the Stovax ASHDON 8546LUC-P8546LUC item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Stovax ASHDON 8546LUC-P8546LUC alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Stovax ASHDON 8546LUC-P8546LUC, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Stovax service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Stovax ASHDON 8546LUC-P8546LUC.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Stovax ASHDON 8546LUC-P8546LUC item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    C l a r e n d o n & A s h d o n L o g E f f e c t S t o v e R a n g e B al a nc e d F lu e With upgradeable control valve I ns t r uc t io n s f or Us e , I ns t a ll a ti o n a nd Se r v ic i ng Fo r use in GB , IE (G rea t Bri ta in and Ei re ) PR0847 Issue 2 (February 2007) I M P O R T A N T Do not attempt to burn rubbish in this fire. This [...]

  • Page 2

    2 CONTENTS COVERING THE FOLLOWING MODELS ASHDON - 8546LUC - P8546LUC / 8544LUC - P8544LUC CLARENDON 8545LUC - P8545LUC / 8547LUC - P8547LUC PAGE APPLIANCE COMMISIONING CHECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 8 Technical Specifications 8 Site Requirements 9 Installation 13 Commissioning 19 SERVICING INSTRUCTIONS 20 Servicing Requir[...]

  • Page 3

    3 FLUE CHECK PASS FAIL 1. Flue is correct for appliance 2. Flue flow test N/A 3. Spillage test N/A GAS CHECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operating on full MTM fires only. Setting Pressure High-mb Low-mb 4. Gas rate m 3 /h 5. Do[...]

  • Page 4

    4 USER INSTRUCTIONS 1. GENERAL 1.1 Installation and servicing must be carried out by a competent person. 1.2 In all correspondence, please quote the appliance type and serial number which can be found on the data badge located at the rear of the stove. 1.3 Ensure curtains are not positioned above the stove, and that there is at least a clearance of[...]

  • Page 5

    7.2 Place log B on the left hand side of the burner with the location bar on the underside of the log fully located in the long slot of the burner. Make sure the log is as far to the left as possible. See diagram 3. 7.3 Place log C on the right hand side of the burner with the location bar on the underside of the log fully located in the long slot [...]

  • Page 6

    6 7.4 Place log D across from the rear log A to log B on the left- hand side. There are cut-outs in both logs for location. See diagram 5. 7.5 There are two ash panels which lay across the front of the burner skin. Place the panel with the flat edge facing the left side of the firebox. There are location holes on this log which fit over the screw h[...]

  • Page 7

    8. THE FLAME FAILURE DEVICE 8.1 This is a safety feature incorporated in all GAZCO fires which automatically switches off the gas supply if the pilot light goes out and fails to heat the thermocouple. 9. ‘RUNNING IN’ 9.1 The surface coating on your GAZCO fires will "burn off" during the first 24 hour of use, producing a harmless and t[...]

  • Page 8

    8 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION COVERING THE FOLLOWING MODELS: ASHDON - 8546LUC - P8546LUC / 8544LUC - P8544LUC CLARENDON - 8545LUC - P8545LUC / 8547LUC - P8547LUC Model Gas Gas Working Aeration Injector Gas Rate Input kW (Gross) Country CAT. Type Pressure m 3 /h High Low 8545LUC-8547LUC I 2H Natural 20 mbar Ø 1 x 14.5 375 0.60[...]

  • Page 9

    9 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1. FLUE AND CHIMNEY REQUIREMENTS NOTE: This appliance can only be installed in conjunction with the flue supplied. 1.1 The flue must be sited in accordance with BS5440: Part 1 (latest editon). See diagram 1. 1.2 Any terminal which is less than 2 metres above any access (level ground, balcony or above a [...]

  • Page 10

    10 1.2 REAR FLUE 8526 Terminal dimensions: 395 x 200 x 200 mm (H x W x D) Cut to length as required on site. Guard Supplied. 1.3 TOP EXIT Two types of top exit flue terminal are available, horizontal and vertical. For a horizontal terminal, decide on the terminal position and measure the height from the top of the appliance to the centre of the req[...]

  • Page 11

    11 1.5 TOP FLUE UP & OUT WITH ADDITIONAL BEND Any additional bend may be used on the horizontal section (either 45° or 90°) but the overall horizontal flue run will be reduced. Refer to diagram 4. 1.6 TOP FLUE VERTICAL KIT (8524/8524AN) - ALL APPLIANCES Vertical from the top of the appliance. (See diagram 5). A minimum vertical rise of 3m (9&[...]

  • Page 12

    12 2. VENTILATION The appliance requires no additional ventilation. 3. INSTALLATION OF THE GAS SUPPLY 3.1 Before installation, ensure that the local distribution conditions (identification of the type of gas and pressure) and the adjustment of the appliance are compatible. 3.2 Ensure that the gas supply is capable of delivering the required amounts[...]

  • Page 13

    13 IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS OF THIS BOOKLET. FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SECTION 10, REPLACING PARTS. 1. CONTROL UPGRADE 1.1 This stove is fitted with a control valve that can be ea[...]

  • Page 14

    14 3.1.5 To set the flue length, measure the total wall thickness, then add 65mm. This total flue length will give the minimum clearance of 50mm between the rear of the stove and the wall. To cut the flue to length using a hacksaw, first insert the square cardboard fitment into the flue. This will support the inner flue. Cut through the flue and fi[...]

  • Page 15

    15 INSTALLATION INSTRUCTIONS INSTALLATION 3.2 TOP EXIT 3.2.1 There are two types of top exit flues available, one with a vertical terminal, the other with a horizontal terminal. Minimum and maximum flue lengths are shown in Diagram 3 under Site Requirements, 1.4. There is an optional decorative collar, part No. 8548, to cover the gap between the to[...]

  • Page 16

    3.3 TOP EXIT - VERTICAL FLUE 3.3.1 If a vertical only flue system has been purchased refer to Site Requirements, Diagram 5. The following areas need careful consideration:- a) Terminal positions b) Flue supports c) Weatherproofing d) Fire precautions For all of the above, local and national codes of practice must be adhered to. TABLE A - TOP EXIT ?[...]

  • Page 17

    17 INSTALLATION INSTRUCTIONS INSTALLATION 5. FUELBED ARRANGEMENTS Remove the cast iron door using the tool provided. The main ceramic components are inside the firebox. NOTE: THE CAST IRON DOOR IS HEAVY, TAKE EXTREME CARE WHEN HANDLING TO AVOID DAMAGING THE OUTER CASING. The fuel bed consists of 5 logs and 2 ash panels. The logs have letters A,B,C,[...]

  • Page 18

    5.4 Place the second ash panel to the right of the first, with the pointed end of the panel fitting into the V shape. This panel should locate on the screw holes of the burner skin. Ensure that both logs are horizontal to the burner ports. 5.5 Place log E across from the rear of log A to log C on the right hand side. Again, there are cut-outs for l[...]

  • Page 19

    1. COMMISSIONING 1.1 Having run the gas supply to the stove, PURGE THE SUPPLY PIPE, this is essential to expel any debris that may block the gas controls. Connect the gas supply to the 8mm compression elbow at the RH rear corner of the stove, see diagram 1. 1.2 Connect a suitable pressure gauge to the test point located on the inlet fitting, and tu[...]

  • Page 20

    20 1. SERVICING REQUIREMENTS This appliance must be serviced at least once a year by a competent person. All tests must be serviced by best practice as described by the current CORGI recommendations. 1.1 Before any test are undertaken on the appliance, conduct a gas soundness test for the property to ensure that there are no gas leaks prior to star[...]

  • Page 21

    21 SERVICING INSTRUCTIONS SERVICING / FAULT FINDING CHARTS NO SPARK IGNITION FUNCTIONAL CHECK 2 Ensure there is no debris around the pilot assembly, (e.g. coal, soot etc.) which could short the spark, clear the area. From Ignition Fault Finding Chart Part 1. Consult the Users Instructions, retry. Operate the valve to light the pilot, does the valve[...]

  • Page 22

    22 SERVICING INSTRUCTIONS REPLACING PARTS 1. GENERAL 1.1 All principal components can be replaced without removing the stove from its installation, although it is essential that the gas supply to the appliance is turned off at the isolation device before proceeding further. 1.2 If, for any reason, the flue has to be removed from the stove, the seal[...]

  • Page 23

    23 SERVICING INSTRUCTIONS REPLACING PARTS 3.4 To remove the pilot injector, undo the compression nut on the pilot feed pipe and withdraw the injector which will be hooked onto the olive. When replacing an injector always make sure it is hooked onto the olive before inserting it into the pilot burner. See diagram 4. 3.5 To remove the electrode, disc[...]

  • Page 24

    24 SERVICING INSTRUCTIONS REPLACING PARTS 4.3 To release the right hand side of the control cover insert the narrow blade screwdriver into the slot shown in diagram 9. Lever it gently and pull from the right hand side at the same time. The cover will now come off, there is a small cylindrical metal spacer inside the cover, this must be kept and rep[...]

  • Page 25

    25 SERVICING INSTRUCTIONS REPLACING PARTS 8.4 Holding the injector with a spanner, undo the feed pipe. NOTE: THE ORIENTATION OF THE INJECTOR. 8.5 Reassemble in reverse order, turn on the gas supply and check for any leaks. 9. PRIMARY AERATION PLATE 9.1 Turn the gas supply off at the isolation device. 9.2 Refer to section 2 to remove the main burner[...]

  • Page 26

    26 SERVICE RECORDS 1ST SERVICE Date of Service:........................................................................... Next Service Due:....................................................................... Signed:........................................................................................ Dealer's Stamp/CORGI Registration Num[...]

  • Page 27

    Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JG Tel: (01392) 261999 Fax: (01392) 444148 E-mail: info@gazco.com A member of the Stovax Group[...]