Tiger NEW HOLLAND T6000 manual

P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS SABER MOWER NEW HOLLAND T6000 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .tiger-mowers.com Current as of 0 1/ 18 /201 2 06022005[...]

T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize [...]

FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower . We recommend that yo[...]

[...]

T ABLE OF CONTENTS SAFETY SECTION _____________________________________ 1 ASSEMBL Y / MOUNTING SECTION ______________________ 2 OPERA TION SECTION _________________________________ 3 MAINTENANCE SECTION ______________________________ 4 P ARTS SECTION ______________________________________ 5 COMMON P ARTS SECTION ____________________________ 6 W ARR[...]

[...]

Saber Safety Section 1-1 SAFETY SAFETY SECTION[...]

Saber Safety Section 1-2 SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VERY SERIOUS INJURY . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, MA Y result in MINOR INJURY .[...]

Saber Safety Section 1-3 SAFETY DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency . Never allow inexperienced or u[...]

Saber Safety Section 1-4 SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the tractor while the tractor is moving. Mount the tractor only when [...]

Saber Safety Section 1-5 SAFETY WARNING! T ransport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the T ractor and Implement and how it handles before transporting on streets and highways. Make sure the T ractor steering and brakes are in good condition and operate properly[...]

Saber Safety Section 1-6 SAFETY WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is OFF before working on the Implement. (SG-20) WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized s[...]

Saber Safety Section 1-7 SAFETY DANGER! NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability t o operate the equipment safely. Before operating the Tractor or Imple- ment, an operator on presc[...]

Saber Safety Section 1-8 SAFETY WARNING! Extreme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death. Any objects that cannot be removed must be clearly marked[...]

Saber Safety Section 1-9 SAFETY WARNING! Do not mow with two machines in the same area except with Cab tractors with the windows closed. (SGM-11) DANGER! Rotary and Flail Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP[...]

Saber Safety Section 1-10 SAFETY Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Mower Head on the ground or securely supported on blocks or stands, disengage the PTO, and turn off the engine. Push and pull the control Levers or Joystick several times to relieve pressure prior to starting any mai[...]

Saber Safety Section 1-11 SAFETY WARNING! In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machi[...]

Saber Safety Section 1-12 SAFETY 002369 HYDRAULIC T ANK 00725746 INSIDE OF CAB 00769737 MOWER DECK P AR T NO. LOCA TION[...]

Saber Safety Section 1-13 SAFETY 02962764 MAIN BOOM, SECONDARY BOOM, MAIN FRAME 02962765 MAIN FRAME 02965262 HYDRAULIC T ANK P AR T NO. LOCA TION 00758194 MOWER DECK[...]

Saber Safety Section 1-14 SAFETY 02967668 MOWER DECK 03200285 OUTSIDE OF CAB 02971 123 HYDRAULIC T ANK 22645 INSIDE OF CAB 22839 MOWER DECK P AR T NO. LOCA TION[...]

Saber Safety Section 1-15 SAFETY 25387 INSIDE OF CAB 10” x 5.5” 31522 MOWER DECK, MAIN BOOM 18.25” x 10” 31523 HYDRAULIC T ANK 22840 INSIDE OF CAB 24028 MOWER DECK P ART NO. LOCA TION[...]

Saber Safety Section 1-16 SAFETY P AR T NO. LOCA TION 32449 HYDRAULIC T ANK 32428 MAIN BOOM[...]

Saber Safety Section 1-17 SAFETY 32709 INSIDE OF CAB 32708 HYDRAULIC T ANK 32707 HYDRAULIC T ANK P AR T NO. LOCA TION[...]

Saber Safety Section 1-18 SAFETY 33302 INSIDE OF CAB 33438 MAIN BOOM 33224 MOWER DECK P AR T NO. LOCA TION 35284 INSIDE OF CAB[...]

Saber Safety Section 1-19 SAFETY 33743 INSIDE OF CAB P AR T NO. LOCA TION 42350 MOWER DECK 33512 INSIDE OF CAB[...]

Saber Safety Section 1-20 SAFETY RED 42399 REFLECTIVE T APE MOWER DECK AMBER 42400 REFLECTIVE T APE MOWER DECK 6T3219 INSIDE OF CAB 6T3220 FRONT PUMP MOUNT 6T3217 MOWER DECK P AR T NO. LOCA TION[...]

Saber Safety Section 1-21 SAFETY 6T3222 INSIDE OF CAB 6T3225 INSIDE OF CAB 6T3224 MOWER DECK P AR T NO. LOCA TION 6T3230 INSIDE OF CAB[...]

Saber Safety Section 1-22 SAFETY 6T3249A MOWER DECK 6T3234 INSIDE OF CAB 6T3236 MOWER DECK 6T3233 HYDRAULIC T ANK P AR T NO. LOCA TION 6T3243 INSIDE OF CAB[...]

Saber Safety Section 1-23 SAFETY TB101 1 MOWER DECK 6T3261 MOWER DECK P AR T NO. LOCA TION 34852 HYDRAULIC T ANK[...]

Saber Safety Section 1-24 SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 ROUND MANUAL CANISTER 33997 1 DECAL, SHEET, MANUAL CANISTER 2 * DECAL 3 * DECAL 4 * DECAL 5 * AVAIL SPECIFIC PRODUCT MANUAL 6 33753 1 E M I SAFETY MANUAL 7 34296 1 FRONT ADHESIVE PAD 8 34297 1 REAR ADHESIVE PAD 9 6T1823 4 ZIP TIE 14” [...]

Saber Safety Section 1-25 SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such . Employer-Employee Operator Regulations U.S. Public L[...]

Saber Safety Section 1-26 SAFETY[...]

Assembly Section 2-1 ASSEMBL Y SECTION CNH T6000 - SABER[...]

ASSEMBL Y Assembly Section 2-2 Before attempting to mount your Tiger mower , it is import ant to read an underst and all of the Safety Messages in the Safety section of this manual. Check complete shipment list against the p acking list to make sure there are no shortages. Make certain the tractor mode l is the appropriate one for the mower receive[...]

ASSEMBL Y Assembly Section 2-3 FRONT PUMP MOUNTING Install the pump mounting bra cket on the front of the tractor with cap-screws a nd lock-washers as shown in the p arts section illustration. DO NOT tighten faste ners at this time. Slide the pump drive shaft int o the crankshaft adapter . The end with the shorter splines should be inserted into th[...]

ASSEMBL Y Assembly Section 2-4 POL YCARBONA TE SAFETY WINDOW NOTE: Installing a boom mower re quires that all of the right side windows be re placed, or protected with a polycarbonate window . This should be done before mounting the main frame. 1. Disconnect gas shock at door . Remove the right side cab door/ window glass from tractor cab by removi[...]

ASSEMBL Y Assembly Section 2-5 MIRROR MOUNT 1. Re move the existing mirror bracket and mirror from the cab. 2 Remove the mirror and knob from existing bracket. 3. Inst all the supplied bracket (usin g supplied hardware) on the cab as shown below . 4. Inst all the mirror with the knob on t he supplied bracket as shown below . Refer to the Part s sec[...]

ASSEMBL Y Assembly Section 2-6 4 CYLINDER EXHAUST MOUNT NOTE: This should be done af ter mounting the main frame. 1. Cut the tractor hood as shown in Pic. #1 to accomodate mod ified exhaust turbo tub e. 2. Remove the muf fler from existing turbo tube. 3. Remove existing turbo tube from tractor turbo. 4. Install the exhu st mounting bracket and supp[...]

ASSEMBL Y Assembly Section 2-7 4 CYLINDER EXHAUST MOUNT (continued) (ASM-NH-0056) Picture #4 Picture #5[...]

ASSEMBL Y Assembly Section 2-8 6 CYLINDER EXHAUST MOUNT NOTE: This should be done af ter mounting the main frame. 1. Cut the tractor hood as shown in below to a ccomodate modified exhaust turbo tube. 2. Remove the muffler from existing turb o tube. 3. Remove existing turbo tube f rom tractor turbo. 4. Install the exhust mounting bracket and support[...]

ASSEMBL Y Assembly Section 2-9 SWITCH BOX WIRING Refer to the Parts Section f or wiring diagrams. Remove top instrument p anel (tach, and hour meter) for access to the wires. Route the red and green switch box wires from the switch box to the bottom right corner of the instrument p anel near window . Connect the red wire to the wh ite wire. (hot wh[...]

ASSEMBL Y Assembly Section 2-10 WEA T HER-P ACK/METRI-P ACK ASSEMBL Y These instructions apply to both W eather-Pack and Metri-pa ck connectors. NOTE: Use the specific tool for the type of connecto r you are assembling. (ASM-C-0009)[...]

ASSEMBL Y Assembly Section 2-11 IDENTIFYING TRACTOR HYDRAULIC SYSTEM The lif t valve uses the Pressure, Return and Load Sense on the tractors rear remotes. Depending on what tractor hydraulic syste m you have determines how the lift valve is plumbed . The Closed Center system is shown below . For more information refer to the Parts Section page for[...]

ASSEMBL Y Assembly Section 2-12 For Open Center hydraulic systems, the li f t valve will need additional pressure. This pressure is taken from the Powe r S teering Return line which is located behind the battery box.[...]

ASSEMBL Y Assembly Section 2-13 LOAD SENSE HOSE ROUTING - OPEN CENTER On a tractor with an Open Center system with Closed Center remotes, the lift valve uses the Pressure, Return and Load Sense on the tractors r ear remotes. The ports used are directly under the valve mounting plate a s shown below. The Pressure hose is routed fr om the tractor rem[...]

ASSEMBL Y Assembly Section 2-14 LOAD SENSE HOSE ROUTING - OPEN CENTER (CONTINUED) On a tractor with an Open Cent er system with O pen Center ports, the lif t valve uses the Pressure, Return and Power Beyo nd ports on the tractors rear remotes. The ports used are directly under the va lve mounting plate as shown below . (ASM- NH-0062A) The Pressure [...]

ASSEMBL Y Assembly Section 2-15 LIFT VALVE MOUNTING Drill a Ø9/16” hole in the fender frame tube of th e tractor 3/4 ” back o f the existin g hole (away from cab). Install the valve mounting bracket to the inside of the right and left rear fender frame tube as shown below and attach it with h ardware listed in the Parts Section of this manual.[...]

ASSEMBL Y Assembly Section 2-16 CABLE CONTROL LEVER ST AND Place the front edge of the suppo rt bracket 2-3/4” back from the lower right front win dow . Rotate st and to be 2-1/4” from the right d oor frame as shown below . Be sure that the locat ion of the stand will allow clearance between the cable control handles and all existing interior l[...]

ASSEMBL Y Assembly Section 2-17 ELECTRONIC LIFT V A L VE PORTS (ASM-C-0089) HIGH PRESSURE FIL TER (JYSTCK CONTROL) The high pressure filter is mou nted to the right valve mounting bracket with hardware, as shown in the part s section . Att ach the two adap ters to the filter . The pressure line from the trac- tor is plumbed to the lef t (Inlet) sid[...]

ASSEMBL Y Assembly Section 2-18 NEW HOLLAND PRIORITY VALVE USED ON DELTA & VALUE UNITS (DANFOSS) The DanFoss lift va lve needs a priority valve and the Delt a and V alue style tractor units need a NH priority valve plug in the tractor rear remotes for the proper hydraulic flow . T orque the body of the plug first to 94Nm and then the small end [...]

ASSEMBL Y Assembly Section 2-19 LIFT VALVE MOUNTING Drill a Ø9/16” hole in the fender frame tube of th e tractor 3/4 ” back o f the existin g hole (away from cab). Install the valve mounting bracket to the inside of the right and left rear fender frame tube as shown below and attach it with h ardware listed in the Parts Section of this manual.[...]

ASSEMBL Y Assembly Section 2-20 LIFT V AL VE HOSE & CABLE ROUTING Attach two clamp s t o the right rear wheel well for proper hose/cable routing. Drill o ne hole for each clamp. Use the lower rear corner of the wheel well as a n origin for measuring. The holes should be Ø10mm or Ø3/8” reamed to accept 3 /8” hardware. Measure from the back[...]

ASSEMBL Y Assembly Section 2-21 BOOM JOYSTICK CONTROL CALIBRA TION (FOR SABER) SUB-D This Danfoss PVG32 control valv e is now equipped with hig her-resolution actuators on Main Boom, Secondary Boom, Deck Roll, and Swivel functio ns. These actuators have “active fault monitoring”. The Deck Shield sectio n does not have “active fault monitoring[...]

ASSEMBL Y Assembly Section 2-22 Run tractor at normal operating RPM to ad just the settings as follows. Set the dead band compensation po tentiometer first. Set the dead band compen sation potentiometer at 50%, or halfway between full clockwise and full counter-clockwise. Setting Signal Adapt ation Potentiometers: Disconnect the Deutsch connectors [...]

ASSEMBL Y Assembly Section 2-23 MAIN BOOM: “A” Port, Boom UP: 7-9 Seconds (Note: Extend secondary boom completely; roll deck to be level with groun d, and lower main boom until deck is on ground. Now index main b oom “up” function and determine the time required for main boom to rise completely .) “B” Port, Boom Down: 6-8 Seconds (Note:[...]

ASSEMBL Y Assembly Section 2-24 (ASM-DF CALIBRA TION SBR-0001)[...]

ASSEMBL Y Assembly Section 2-25 SABER HOSE ROUTING WA R N I N G N O T E : The sudden release of hydraulic pressure could cause the sudden movement of very heavy p ar ts. Anyone in the way of these p arts could be severely hu rt or killed. DO NOT ALLOW these hydraulic hos es to BREAK or BURST in order to prevent hydraulic failure Make sure the hoses[...]

ASSEMBL Y Assembly Section 2-26 SABER HOSE ROUTING (CONTINUED) Arrange the hoses in the clamp th at att aches to the boom mounting bracket as sh own above, with the 1” motor hoses closest to the ma in fram e. Pull the hoses snug from the swivel to the main frame clamps, when main boom is fully forward, and tighten the hoses in the clamp. Make sur[...]

ASSEMBL Y Assembly Section 2-27 (ASM-C-0023) SIDE HYDRAULIC T ANK INST ALLA TION Install all fitt ings and tubes into tank and t ank filter as shown in the Pa rt s Section illustration. Insert tank sight glass into front side of tank. Place the t ank in the mounting bracket on the main frame as shown in the Parts Section. Secure the tank with the t[...]

ASSEMBL Y Assembly Section 2-28 FILLING HYDRAULIC RESER VOIR Refer to the maintenance section for filling specifications and hydraulic oil requirements. NOTE: St arting or running your Tiger mowe r before filling reservoir will cause serious damage to hydraulic pump. (ASM-C-0004hydro resrv) INST ALLING O-RING FITTINGS Installing straight, 45 º and[...]

ASSEMBL Y Assembly Section 2-29 SOLENOID BRAKE V AL VE Install a solenoid valve on the mounting bracket with the supplied hardware as shown in the Parts Sectio n in this manual. While installing the fittings to the brake valve, the e lectical coil on the spool may have to be removed t o make room. When reinstalling the coil, it is important to use [...]

ASSEMBL Y Assembly Section 2-30 COOLER MOUNTING - SIDE T ANK Mount the cooler mounting bracket s on the top rear side of the side hydraulic tank. Locate the bolt plates on t he top of the tan k and secure the appropriate cooler bracket to the tank with the hardware provided. Attach the screen and cooler to the bracket s. Refer to the Parts Section [...]

ASSEMBL Y Assembly Section 2-31 AXLE BRACE MOUNTING The axle braces are to be mounted under the rear a xle of the tractor with spa cers. The other end of the right axle brace mounts to the out side of the lower rear corner of the main frame. After att aching the boom rest, it should fit tightly and level under the tractor . Attach the right axle br[...]

ASSEMBL Y Assembly Section 2-32 DECK A TT ACHMENT Attach the head to the se condary boom using the pins and hardware shown in the Parts Section. Inst all the deck pivot cylinder using the p ins and hardware also shown in the Part s Section. Connect the fittings and hoses from the pivo t cylinder to the small preformed tubes on the boom arm. Connect[...]

ASSEMBL Y Assembly Section 2-33 4WD FRONT WHEEL ADJUSTMENT In order to prevent inte rferences with mounted equipm ent, the front wheels on a 4WD T6000 tractor will ha ve to be adjusted to be appr oximately 68” center to center distance (see illustra tion below). For tractors with mounted loaders, that distance should be app roximately 76”. Doub[...]

ASSEMBL Y Assembly Section 2-34 FINAL PREP ARA TION FOR OPERA TION Place operators safety and op eration decals on the steering column and side counsel where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book. The decals are t[...]

Operation Section 3-1 ©201 1 Alamo Group Inc. OPERA TION SECTION[...]

OPERATION Saber Operation Section 3-2 ©201 1 Alamo Group Inc. OPERA TION TIGER SABER BOOM MOWER OPERA TING INSTRUCTIONS Safety is of primary import ance to the owner/operator an d to the manufacurer . Ti ger Saber Booms are manufactured with quality material by skilled workers. The first sect ion of this manual includes a list of Safety Messages, [...]

OPERATION Saber Operation Section 3-3 ©201 1 Alamo Group Inc. OPERA TION 1.OPERA TOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualifi ed operator . A qualified operator ha s read and understands th e implement and tractor Operator’s Ma nuals and is experienced in implem ent and tractor operation and all associated safet[...]

OPERATION Saber Operation Section 3-4 ©201 1 Alamo Group Inc. OPERA TION 2.TRACT OR REQUIREMENTS In addition to tractor horsepowe r and size required to operate the boom unit, the tractor must also be pro perly equipped to provide operat or protecti on, to alert approaching vehicle drivers of the tractor ’ s presence, and to ensure tractor stabi[...]

OPERATION Saber Operation Section 3-5 ©201 1 Alamo Group Inc. OPERA TION 2.3 T ractor Lighting and SMV Emblem If the tractor will be operated near or traveled on a public roadw ay it must be equipped wit h proper warning lighting and a Slow Mo ving V ehicle (SMV) emblem which ar e clearly visible fro m the rear of the unit. Most tractor’s have d[...]

OPERATION Saber Operation Section 3-6 ©201 1 Alamo Group Inc. OPERA TION 3.GETTING ON AND OFF THE TRACT OR Before getting o nto the tractor , the operato r must read and comple tely understand the implement and tractor operator manuals. If any p art of either manual is no t completely understood, consult an author ized dealer for a complete explan[...]

OPERATION Saber Operation Section 3-7 ©201 1 Alamo Group Inc. OPERA TION BEFORE leaving the tracto r seat, alw ays set th e parking brake a nd/or set the tractor transmission in parking ge ar , disengage the PTO, stop the engine, remove the key , and wait for all movin g parts to stop. Place the tractor shift lever into a low range or par king gea[...]

OPERATION Saber Operation Section 3-8 ©201 1 Alamo Group Inc. OPERA TION When rot ating part s are in motion, serious injury may occur if caution is n ot used or danger is not recognized. Never allow byst anders with 300 yards of the machine when mower is in operation. Be sure the ball valve on the mower hydraulic t ank are OPEN before sta rting t[...]

OPERATION Saber Operation Section 3-9 ©201 1 Alamo Group Inc. OPERA TION 5.2 Boom Unit Pre-Operati on Inspection and Service Inspect and service the boom arm and head prior to operation. Damaged and/or broken p arts should be repaired and/or replaced immedi ately . T o ensure the unit is ready for oper ation, conduct the following: OPS-B- 0020 5.1[...]

OPERATION Saber Operation Section 3-10 ©201 1 Alamo Group Inc. OPERA TION FRAME ASSEMBL Y • Inspect condition of mounting fra me weldment. • Inspect condition of Swivel Assy . • Ensure all bolts and screw s are in posi tio n and ar e properly torqued. • Ensure all pins are in place and fastened with screws. • Ensure frame is properly mou[...]

OPERATION Saber Operation Section 3-11 ©201 1 Alamo Group Inc. OPERA TION BOOM ARM ASSEMBL Y • Inspect condition of each a rm se ction weldm ent • Ensure all pins ar e in pl a ce . • Ensure all bolts, nuts and rollpins ar e pr op e rly installed. • Check condition of bushings at boom pivot points and hydr aulic cylinder tangs. • Ensure e[...]

OPERATION Saber Operation Section 3-12 ©201 1 Alamo Group Inc. OPERA TION HYDRAULIC PUMP/OIL RESERVOIR • Check oil reservoir leve l and oil condition. (Add specific type oil if low) • Change hydraulic oil filter and hydrauli c oil according to mainte nance schedule. • Ensure th ere are no oil leaks a nd fitting a re properly connected • In[...]

OPERATION Saber Operation Section 3-13 ©201 1 Alamo Group Inc. OPERA TION ROT AR Y HEAD INSPECTION • Inspect blades and bl ade bo lts for looseness and excessive wear . R otate to 90° to make for checking easier . Re place damaged, worn, and missing blades as complete set s to maintain rot ary balance. • Ensure motor bo lts and nut s are tigh[...]

OPERATION Saber Operation Section 3-14 ©201 1 Alamo Group Inc. OPERA TION Boom PRE-OPERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conductin g the inspection, make s ure the tractor engine is off, all rot ation has stopped and the tractor is in p ark with the p arki[...]

OPERATION Saber Operation Section 3-15 ©201 1 Alamo Group Inc. OPERA TION T ractor PRE-OPERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conducting the inspection, make sure the tr actor engine is off, all rot ation has stopped and the trac tor is in par k with the pa[...]

OPERATION Saber Operation Section 3-16 ©201 1 Alamo Group Inc. OPERA TION 5.3 Cutting Component Inspection Inspect blade p an and blade assembly for the following: OPS-U-0031 Inspect the Blades daily for abnormal wear . REPLACE BOTH BLAD ES on that carrier IMMEDIA TEL Y if either blade has: • Become bent or deformed from it’ s original sh ape [...]

OPERATION Saber Operation Section 3-17 ©201 1 Alamo Group Inc. OPERA TION 5.4 Blade Bolt Inspection Inspect Blade Bolt Head da ily for wear as followed: Inspect the Blade Bolt Heads d aily for abn ormal wear . REPLACE BOTH BLADE BOL TS on the Blades IMMEDIA TEL Y if either blade bolt s has: • Visible cracks or • If the reces sed area on blade [...]

OPERATION Saber Operation Section 3-18 ©201 1 Alamo Group Inc. OPERA TION 6.JOYSTICK CONTROL[...]

OPERATION Saber Operation Section 3-19 ©201 1 Alamo Group Inc. OPERA TION JOYSTICK FW/BACK MOVES MAIN BOOM JOYSTICK LEFT/RIGHT MOVES SECONDARY BOOM LEFT JOYSTICK ROLLE R MOVES DECK ROLL[...]

OPERATION Saber Operation Section 3-20 ©201 1 Alamo Group Inc. OPERA TION RIGHT JOYSTICK ROLLER MOVES BOOM SWIVEL SHIELD SWITCH(on switch box) OPERA TES SAFETY SHIELD 6.1 Switchbox The Safety Shield lever opens and closes the shield located on the fron t of the cutter head. When moving at or near the ground, always have th e shield in the c losed [...]

OPERATION Saber Operation Section 3-21 ©201 1 Alamo Group Inc. OPERA TION Check to make sure mo wer switch is in the “OFF” posit ion. The unit is designed not to start if the switch is in the “ON” position. If tr actor starts with switch on, tu rn off tractor and conta ct your local T iger dealership for assist ance. S tart the tractor and[...]

OPERATION Saber Operation Section 3-22 ©201 1 Alamo Group Inc. OPERA TION 6.2 Main Control Switch Box The Mower Control switch turns the mower “ON” and “OFF”. This switch is to be in the “OFF” position to start the tractor . If the switch is “O N” and the tractor ignition switch is tur ned to “ON” the red “mower run” indica[...]

OPERATION Saber Operation Section 3-23 ©201 1 Alamo Group Inc. OPERA TION The Master Switch a lso provides power to the “Deck Fl oat”, “Shield” a nd “T ravel Lock” Functions of the mower deck. The Deck Float function allows the ground roller of the flail mower head to follo w the contour of the ground. T o operate the deck float functi[...]

OPERATION Saber Operation Section 3-24 ©201 1 Alamo Group Inc. OPERA TION 7.DRIVING THE TRAC TOR AND IMPLEMENT Safe tractor transport req uires the operator to po ssess a thorough knowledge of the m odel being operated and precaution s to take while driving with a n attached implement. Ensure the trac tor has the capacity to handle the weight of t[...]

OPERATION Saber Operation Section 3-25 ©201 1 Alamo Group Inc. OPERA TION T ransport on ly at speeds where you can maintain control of the equipment. Seriou s accidents and injuries can result from oper ating this equipment at high sp eeds. Unders tand the Tr actor and Implement and how it handles before transporting on street s and high ways. Mak[...]

OPERATION Saber Operation Section 3-26 ©201 1 Alamo Group Inc. OPERA TION 7.2 Brake and Differential Lock Setting Make sure the tr actor brakes are in good oper ating condition. T ractor brakes can be set to operate independently allowing sin gle rear wheel braking action or locked together to provide simult aneous rear wheel braking. FOR MOST DRI[...]

OPERATION Saber Operation Section 3-27 ©201 1 Alamo Group Inc. OPERA TION 7.3 Driving the T ractor and Boom S tart off driving at a slo w speed and gradually increase your speed while maintainin g comple te control of the tractor . N ever operate the tractor at speeds that cannot be safely handled or which will prevent the operator from stopping q[...]

OPERATION Saber Operation Section 3-28 ©201 1 Alamo Group Inc. OPERA TION 8.OPERA TING THE BOOM UNIT AND A TT ACHED HEAD THE OPERA TOR MUST COMPLETEL Y UNDERST AND HOW TO OPERA TE THE TRACTOR AND MOWER AND ALL CONTROLS BEFORE A TTEMPTING TO MOW . The operator must read an d underst and the Safety and Oper ation Sections of this manual an d the tra[...]

OPERATION Saber Operation Section 3-29 ©201 1 Alamo Group Inc. OPERA TION 8.1 Foreign Debris Hazards/Overhead Obstructions An area to be cut must first be inspe cted for objects that co uld be thrown or that could damage the machine. W alk through the area loo king for fences, boulders, rocks, culverts, stumps or metal object s. Mark the inspected[...]

OPERATION Saber Operation Section 3-30 ©201 1 Alamo Group Inc. OPERA TION 8.3 Mower Operation The rot ating part s in this machine have been designed and teste d for rugged use. However , they could fail upon imp act with heavy solid object s-such as steel guard rails, con crete abutments,etc., causing them to be thrown at a very high velocity . N[...]

OPERATION Saber Operation Section 3-31 ©201 1 Alamo Group Inc. OPERA TION A flail mower deck should be carried so that the p art of the deck weight is carried by the boom and part carried by the groun d roller , when moving on the ground. When the flail mower is carried this way , the ground roller follows the contour of the ground more easily dur[...]

OPERATION Saber Operation Section 3-32 ©201 1 Alamo Group Inc. OPERA TION disengage the mowe r , and return boom to a safe travel position. Return to st arting point and make next p ass, etc. After the first d ay of operation, all bolt s should be checked and tightened securely . This should be done periodically to ensure the bolt s do not b ecome[...]

OPERATION Saber Operation Section 3-33 ©201 1 Alamo Group Inc. OPERA TION 8.6 50” Boom Flail The 50” boom flail mower was designed for cutting brush and folia ge up to 2 inch es in diame ter or multiple branches that have a total cross section area equivalent to on e 2 inch branch. Cuttin g multiple limbs at the same time may overlo ad the mow[...]

OPERATION Saber Operation Section 3-34 ©201 1 Alamo Group Inc. OPERA TION 8.8 Saber Flail The Saber flail mower was designe d for cutting brush and foliage up to 4 inches in dia meter or multiple branches that have a tota l cross secti on area equivalent to one 4 inch br anch. Cutting multip le limbs at the same time may overload the mower cau sin[...]

OPERATION Saber Operation Section 3-35 ©201 1 Alamo Group Inc. OPERA TION 8.10 Shutting Down the Att ached Head- For S t a ndard Equipment T o shut down att ached mower head, first bring the tractor to a complete stop. Decrease engin e RPM to idle then disengage cutterhea d. The mower head will come to a complete stop within a suitable amount of t[...]

OPERATION Saber Operation Section 3-36 ©201 1 Alamo Group Inc. OPERA TION 9.1 Unstowing the Boom T o un-stow the boom from the boom re st, proceed as follows. Extend secondary boom “OUT” an d move main boom “UP” of f of horizonta l support. Swivel boom “FOR W ARD” perpendicular to tractor and switch travel lock to “OFF” (ONL Y FOR [...]

OPERATION Saber Operation Section 3-37 ©201 1 Alamo Group Inc. OPERA TION 9.3 T ransporting on Public Roadways Extreme caution should be used when transporting th e tractor and mower on public roadways. The tractor must be equip ped with all required safety warnin g features including a SMV emb lem and flashing war ning lights to alert drivers of [...]

OPERATION Saber Operation Section 3-38 ©201 1 Alamo Group Inc. OPERA TION When operating on public roa ds, have consideration for other r oad users. Pull to the side of the road oc casionally to allow all following traffic to pass. Do no t exceed the legal speed limit set in your state or muni cipality for agricultural tractors. Always stay alert [...]

OPERATION Saber Operation Section 3-39 ©201 1 Alamo Group Inc. OPERA TION 9.4 T ransporting Unit by Flatbed T railer Park flatbed on leve l area. Drive tra ctor onto ce nter of flatbed to avoid uneven distri b ution of weight and st aying within local width restricti ons. If boom is over local height re strictions, you will need to extend booms ou[...]

OPERATION Saber Operation Section 3-40 ©201 1 Alamo Group Inc. OPERA TION 10. TRACTO R, BOOM, AND A TT ACHED HEAD STORAGE Properly prep aring and storing th e unit at the end of the season is critical to maint aining its appearance and to help ensure years of dep endable service. The following are suggested storag e procedures: • Thoroughly clea[...]

OPERATION Saber Operation Section 3-41 ©201 1 Alamo Group Inc. OPERA TION BEFORE leaving the tracto r seat, alw ays set th e parking brake a nd/or set the tractor transmission in parking ge ar , disengage the PTO, stop the engine, remove the key , and wait for all movin g parts to stop. Place the tractor shift lever into a low range or par king ge[...]

OPERATION Saber Operation Section 3-42 ©201 1 Alamo Group Inc. OPERA TION[...]

Maintenanc e Sec tio n 4- 1 ©201 1 Alamo Group Inc. MAINTENANCE SECTION[...]

MAINTENANCE Saber Maintenance Section 4-2 ©201 1 Alamo Group Inc. MAINTENANCE General Instructions T iger Mowers are designed for high pe rformance and rugged durability , ye t with simplified maintenance. The purpose of this section of the manual is to help the operator in the reg ular serv icing of the mo wer . Regular maintenance at the interva[...]

MAINTENANCE Saber Maintenance Section 4-3 ©201 1 Alamo Group Inc. MAINTENANCE Regular Maintenance The intervals at which regular servicing should be do ne are based on ho urs o f oper ation . Use th e tractors h our meter to determine when reg ular servicing is required. Daily or Every 8 Hours ITEM SERVICE COMMENTS Drive Shaft Y oke, U-J oin t Gre[...]

MAINTENANCE Saber Maintenance Section 4-4 ©201 1 Alamo Group Inc. MAINTENANCE ITEM SERVICE COMMENTS Hydraulic Fittings Check for leaks T ighten when needed. Do Not use hands to check for leaks, see maintenance precautions Knives Check Inspect for missing or damaged knives, change as needed or sharpen as needed. S pindle mounting bolts Check 3/4”[...]

MAINTENANCE Saber Maintenance Section 4-5 ©201 1 Alamo Group Inc. MAINTENANCE WEEKL Y OR EVER Y 40 HOURS ITEM SERVICE COMMENTS Rotary S p indle Lubricate Eve ry 40 hour s or week ly WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hyd. Fluid Change Change afte r first 50 hours only , then Filter every 500 hrs. yearly or if indicated by 10[...]

MAINTENANCE Saber Maintenance Section 4-6 ©201 1 Alamo Group Inc. MAINTENANCE TROUBLESHOOTING SYMPTOMS CAUSE REMEDY Vib r at i on 1. Loose Bolts 1. Check all bolts and tighten to recommended torque specifications 2. Cutter assembly 2a. Check for damage blades, disc Unbalanced or cutter shaft. Replace if needed. 2b. Check for wire , rope, etc. enta[...]

MAINTENANCE Saber Maintenance Section 4-7 ©201 1 Alamo Group Inc. MAINTENANCE TROUBLESHOOTING (Continued) SYMPTOMS CAUSE REMEDY Motor runs but 1. Belts 1. Inspect belts and pulleys. Replace will not cut . belts and rep air as needed. 2. T ensioner 2. Adjust tensioner nut flat washer washer is flush with top of guide. Mower turns slowly 1. Contamin[...]

MAINTENANCE Saber Maintenance Section 4-8 ©201 1 Alamo Group Inc. MAINTENANCE LUBRICA TION RECOMMENDA TIONS Description Application General S pecification Recommended Mobil Lubricant T ractor Hydraulics Reserv oir JD-20C Mobilfluid® 424 Mower Hydraulics Reservoir Cold T emperatures 0° F ISO 46 Anti-Wear -Low T emp Mobil DTE® 15M St a r t - U p [...]

MAINTENANCE Saber Maintenance Section 4-9 ©201 1 Alamo Group Inc. MAINTENANCE T ORQUE SPECIFICA TIONS *These are general specifications. Check your tractor operato rs or service manual for exact specifi cations.[...]

MAINTENANCE Saber Maintenance Section 4-10 ©201 1 Alamo Group Inc. MAINTENANCE POL Y CARBONA TE CARE & MAINTENANCE The propriet ary UV and Abrasio n Resistant Surfac e coating on SHIELD S® SUPERCOA TED™ polycarbonate significantly improves performa nce. Periodic cleaning using proper proc edures and comp atible cleaners are recommended to p[...]

MAINTENANCE Saber Maintenance Section 4-11 ©201 1 Alamo Group Inc. MAINTENANCE RECOMMENDED FILLING INSTR UCTIONS FOR HYDRAULIC RESER VIORS When filling or checking the oil level, the unit should be parked on a level su rface., shut ” OFF”, and allow suff icient time to cool to ambient tempera ture. Use caution when removing th e pressuri zed b[...]

MAINTENANCE Saber Maintenance Section 4-12 ©201 1 Alamo Group Inc. MAINTENANCE DET AILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FIL TER ELEMENT : Assure system has been shut d own and de- pressurized. Locate High Pres sure Filter housing. Confirm that the element that is about to be installed matches the ele ment p/n o n the filter model t[...]

MAINTENANCE Saber Maintenance Section 4-13 ©201 1 Alamo Group Inc. MAINTENANCE GREASING GROUND ROLLER SHAFT -FLAIL Locate grease zerks on ea ch end of roller tu be at lo wer end of head. Normal cond itions require one or two pump in each bearing, using Lithiu m-Complex Extreme Pressure grease conforming to NLGI2- ISO 320 specifications. This is to[...]

MAINTENANCE Saber Maintenance Section 4-14 ©201 1 Alamo Group Inc. MAINTENANCE BALL V AL VES The ball valve at the h ydraulic reservoir may nee d to be closed during cert ain maintenance or repa ir procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with va lve) WHEN TRACTOR IS RE-ST ARTED OR PUMP IS COUPLED TO MOTOR OR P .T .O.! Failure [...]

MAINTENANCE Saber Maintenance Section 4-15 ©201 1 Alamo Group Inc. MAINTENANCE GREASING POINTS ON BOOM AND PIVOT Locate grease zerks (8) on deck pivot assemb ly , (2) on the deck end of second ary boom, (2) at main/ secondary boom joint, a nd (2) at swivel end o f main boom. Inject Lithium-Complex Extreme Pressure g rease conforming to NLGI2-IS O [...]

MAINTENANCE Saber Maintenance Section 4-16 ©201 1 Alamo Group Inc. MAINTENANCE GREASING SPINDLE Locate grease fitting o n inside of deck housing. Inje ct T iger S pindle Lubricant, p art number 06540 000 into spindle housing. Fill with lubricant unt il lubricant weeps out of top spindl e seal. Lubricate spindl e weekly or every 40 hours of use. TI[...]

MAINTENANCE Saber Maintenance Section 4-17 ©201 1 Alamo Group Inc. MAINTENANCE GREASING PUMP DRIVE SHAFT COUPLER With engine stopped, ensur e drive shaft alignm ent by grasping coupler an d sliding back and forth. Coupler should slide freely with approxim ately 1/8” of end play . If coupler does not slide freely , inspect for loose pump moun t b[...]

MAINTENANCE Saber Maintenance Section 4-18 ©201 1 Alamo Group Inc. MAINTENANCE GREASING THE BOOM SWIVEL Locate the zerks on the main swivel boss (2), main boom pivot boss (2) and on bo th ends of the boom swivel cylinder . Inject Lithium-Complex Extreme Pressure grease co nforming to NLGI2-ISO 320 specification u ntil grease b egins to prot rude f[...]

MAINTENANCE Saber Maintenance Section 4-19 ©201 1 Alamo Group Inc. MAINTENANCE Blades Check the Blades for cracks and w ear and Blade Bolts for tightness, daily . Blades should be replaced when they are worn excessively , bent, deformed, or out of balance. Blades should always be replac ed in pairs. Bl ade s of different weight s can cause serious[...]

MAINTENANCE Saber Maintenance Section 4-20 ©201 1 Alamo Group Inc. MAINTENANCE ROT AR Y KNIFE REPLACEMENT 1. Be sure you have a complete matching set of new knives for replacement. 2. Remove knives and inspect holes for damage. Also watch for cracks in the disk around the ho les. 3. Lube threads with anti- seize, motor oil or grease. Inst all bolt[...]

MAINTENANCE Saber Maintenance Section 4-21 ©201 1 Alamo Group Inc. MAINTENANCE Flail Blades Inspection Inspect the Blades daily for abnorma l wear . REPLACE ALL BLADES on the carrier IMMEDIA TEL Y if any blades have: • Become bent or deformed from it s original shape, or • Wear insid e the blade bolt hole, or • Any cracks are visib l e, or ?[...]

MAINTENANCE Saber Maintenance Section 4-22 ©201 1 Alamo Group Inc. MAINTENANCE Blade Pins and D-Ring Inspection Blade Pins and D-Rings daily for wear or dam age as follows: Inspect the Blad e pins and D-Rings daily for abnorma l wear . Make sure the cotter pins are in place and pro perly spread. REPLACE BL ADE Pins and D-Rings IMMEDIA TEL Y if the[...]

MAINTENANCE Saber Maintenance Section 4-23 ©201 1 Alamo Group Inc. MAINTENANCE Flail Axe Blades Inspection Inspect the Blades daily for abnorma l wear . REPLACE ALL BLADES on the carrier IMMEDIA TEL Y if any blades have: • Become bent or deformed from it s original shape, or • Oval shape wear inside the bla de bolt hole, or • Any cracks are [...]

MAINTENANCE Saber Maintenance Section 4-24 ©201 1 Alamo Group Inc. MAINTENANCE 50” FLAIL KNIFE BLADE REPLACEMENT 1. If knives are damaged or badly wo rn, they will need to be replaced as a set. Replacing a single knife can cause severe vibration and possible da mage to th e mower . The knife should not be welded on for any reason. 2. Always repl[...]

MAINTENANCE Saber Maintenance Section 4-25 ©201 1 Alamo Group Inc. MAINTENANCE DO NOT re-use the locking hex nut s for mounting the knives. If hex nut become s loose, or requir ed removal for knife replacement or any other reason, they must b e discarded and replaced with new nuts. Knives should not be welded on for any reason. 63” BOOM FLAIL KN[...]

MAINTENANCE Saber Maintenance Section 4-26 ©201 1 Alamo Group Inc. MAINTENANCE HEA VY DUTY SPINDLE ASSEMBL Y INST ALLA TION AND BEARING ADJUSTMENT A press MUST be used to install bear ing cups, bearing cone s, and seals. DO NOT use a hammer to inst all races, bearings, or seal s. The part s of assembly may be damaged. NOTE : The grease zerk and gu[...]

MAINTENANCE Saber Maintenance Section 4-27 ©201 1 Alamo Group Inc. MAINTENANCE SPINDLE BEARING INST ALLA TION 1. Press upper bea ring cup into the spindle housing 2. T urn the sp indle housing over and pr ess in the lower bearing cup. 3. Place the lower bear ing cone in the bearing cup. Next press the seal into the spindle housing. The in ner lip [...]

MAINTENANCE Saber Maintenance Section 4-28 ©201 1 Alamo Group Inc. MAINTENANCE Boom Cylinder Removal and Replacement Instructions 1. Clear the ar ea of all personnel before lowering the boom mower head. 2. From the tractor seat with your seat belt fast ened around you, Lo wer the boom mower head to the ground. Extend the boo m to the fu rthest rea[...]

MAINTENANCE Saber Maintenance Section 4-29 ©201 1 Alamo Group Inc. MAINTENANCE CUTTERSHAFT BEARING REPL ACEMENT FOR FLAIL MOWERS 1. Remove existing cuttershaft, be arings and string guards. 2. Make sure that the end knives on each end of the cuttershaft are orient ated as shown. 3. Apply anti-seize on cuttershaf t as shown on next page. 4. Install[...]

MAINTENANCE Saber Maintenance Section 4-30 ©201 1 Alamo Group Inc. MAINTENANCE[...]

MAINTENANCE Saber Maintenance Section 4-31 ©201 1 Alamo Group Inc. MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be perform ed daily or every 8 hours of service, following the detaile d maintenance instructions in th e operators manual. _______ Pump Drive Shaft: If r equired with drive shaf t/coupler chec k for end play and[...]

MAINTENANCE Saber Maintenance Section 4-32 ©201 1 Alamo Group Inc. MAINTENANCE[...]

P ARTS SECTION NH T6000 SABER BOOM[...]

NOTES[...]

PART NAME INDEX PARTS ORDERING GUIDE ......................................................................................................................................................................... 4 NOTES .......................................................................................................................................[...]

PARTS ORDERING GUIDE ©2011 Alamo Group Inc. Parts Section 5-4 NH T6000 SABER[...]

NOTES ©2011 Alamo Group Inc. Parts Section 5-5 NH T6000 SABER[...]

TRACTOR MOUNT KIT ©2011 Alamo Group Inc. Parts Section 5-6 NH T6000 SABER[...]

TRACTOR MOUNT KIT Continued... ITEM PART NO. QTY. DESCRIPTION 1 06300076 1 FRM,LH,SBR 2 06300075 1 MNFRM,SBR 3 06300080 1 MNT,TANK 4 06380012 1 TANK,RESERVOIR 5 06505077 1 CAP,BREATHER 6 21725 6 HEX NUT,1/2",NC 7 22018 2 FLATWASHER,1/2",WIDE 8 06505067 1 SIGHT GAUGE 9 06505044 1 FLTR ASSY,IN-TANK CPLT 10 21627 4 NYLOCK NUT,3/8",NC 11[...]

TRACTOR MOUNT KIT - HYDRAULICS ©2011 Alamo Group Inc. Parts Section 5-8 NH T6000 SABER[...]

TRACTOR MOUNT KIT - HYDRAULICS Continued... ITEM PART NO. QTY. DESCRIPTION 1 06300076 1 FRM,LH,SBR 2 06300075 1 MNFRM,SBR 3 06300080 1 MNT,TANK 4 06700090 1 TANK,ASSY 5 23152 1 PUMP 6 TF4852 2 KIT,FLANGE,#20 7 06400114 1 MNT,BRAKE VALVE 8 33880 2 FLATWASHER,3/4",SAE 9 25341 2 CAPSCREW,20MM X 70MM,2.5P 10 24849 2 SPACER,7/8"ID X 1-1/4"[...]

AXLE BRACE AND BATTERY BOX ©2011 Alamo Group Inc. Parts Section 5-10 NH T6000 SABER[...]

AXLE BRACE AND BATTERY BOX Continued... ITEM PART NO. QTY. DESCRIPTION 1 ------ - MAIN FRAME *REFER TO TRACTOR MNT KIT PAGE 2 06300032 1 AXLE BRC,LH 3 06300031 1 AXLE BRC,RH 4 21825 4 HEX NUT,3/4",NC 5 33880 8 FLATWASHER,3/4",SAE 6 21833 4 CAPSCREW,3/4" X 2-1/4",NC 7 22016 8 FLATWASHER,3/8" 8 21627 4 NYLOCK NUT,3/8",NC[...]

MID-MOUNT VALVE RELOCATION ©2011 Alamo Group Inc. Parts Section 5-12 NH T6000 SABER[...]

MID-MOUNT VALVE RELOCATION Continued... ITEM PART NO. QTY. DESCRIPTION 1 ------ 3 CAPSCREW (EXISTING HARDWARE) 2 ------ 3 HEX NUT (EXISTING HARDWARE) 3 ------ 1 VALVE MOUNTING PLATE,TOP (EXISTING) 4 06411134 1 STRAP,VLV,RELOCATE 5 ------ 1 VALVE MOUNTING PLATE,BOTTOM (EXISTING) 6 21581 3 CAPSCREW,5/16" X 1-1/4",NC 7 21577 3 NYLOCK NUT,5/1[...]

JOYSTICK AND SWITCH BOX MOUNT ©2011 Alamo Group Inc. Parts Section 5-14 NH T6000 SABER[...]

JOYSTICK AND SWITCH BOX MOUNT Continued... ITEM PART NO. QTY. DESCRIPTION 1 06520041 2 MOUNT,RAM,BALL,1-1/2",NPT 2 06520042 1 MOUNT,RAM,ARM,1.5" X 2.75" 3 35033 1 CAN,JYSTK,CPLT,DF 4 35205 1 SETSCREW,3/8" X 2",NC,KNURLED PT 5 35206 1 HEX NUT,JAMB,3/8",NC 6 35204 1 KNOB,3/8",NC,INSERT 7 33691 1 JOYST,4AXIS,RH 8 328[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - LOAD SENSE ©2011 Alamo Group Inc. Parts Section 5-16 NH T6000 SABER[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - LOAD SENSE Continued... ITEM PART NO. QTY. DESCRIPTION 1 06340008 1 VLV MNT,RH 2 06340009 1 VLV MNT,LH 3 34622 1 PLATE,VALVE,REAR MNT 4 21631 4 CAPSCREW,3/8” X 1-1/4”,NC 5 21988 4 LOCKWASHER,3/8" 6 21625 4 HEX NUT,3/8",NC 7 22016 3 FLATWASHER,3/8" 8 06505029 1 FILTER,HP,3/4"SAE,VIS IND --[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - TERRAGLIDE ©2011 Alamo Group Inc. Parts Section 5-18 NH T6000 SABER[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - TERRAGLIDE Continued... ITEM PART NO. QTY. DESCRIPTION 1 06340008 1 VLV MNT,RH 2 06340009 1 VLV MNT,LH 3 34622 1 PLATE,VALVE,REAR MNT 4 21631 4 CAPSCREW,3/8” X 1-1/4”,NC 5 21988 4 LOCKWASHER,3/8" 6 21625 4 HEX NUT,3/8",NC 7 22016 3 FLATWASHER,3/8" 8 06505029 1 FILTER,HP,3/4"SAE,VIS IND --[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - POWER BEYOND ITEM PART NO. QTY. DESCRIPTION 1 06340008 1 VLV MNT,RH 2 06340009 1 VLV MNT,LH 3 34622 1 PLATE,VALVE,REAR MNT 4 21631 4 CAPSCREW,3/8” X 1-1/4”,NC ©2011 Alamo Group Inc. Parts Section 5-20 NH T6000 SABER[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - POWER BEYOND Continued... ITEM PART NO. QTY. DESCRIPTION 5 21988 4 LOCKWASHER,3/8" 6 21625 4 HEX NUT,3/8",NC 7 22016 4 FLATWASHER,3/8" 8 06505029 1 FILTER,HP,3/4"SAE,VIS IND --- 06505039 1 ELEMENT,FILTER 9 06505081 1 INDICATOR,VIS,HP FILTER 10 21579 4 CAPSCREW,5/16" X 3/4",NC 11 332[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - OPEN CENTER ©2011 Alamo Group Inc. Parts Section 5-22 NH T6000 SABER[...]

ELECTRONIC PROPORTIONAL LIFT VALVE - OPEN CENTER Continued... ITEM PART NO. QTY. DESCRIPTION 1 06340008 1 VLV MNT,RH 2 06340009 1 VLV MNT,LH 3 34622 1 PLATE,VALVE,REAR MNT 4 21631 4 CAPSCREW,3/8” X 1-1/4”,NC 5 21988 4 LOCKWASHER,3/8" 6 21625 4 HEX NUT,3/8",NC 7 22016 3 FLATWASHER,3/8" 8 06505029 1 FILTER,HP,3/4"SAE,VIS IND -[...]

TRACTOR REMOTE PLUMBING - OPEN CENTER ©2011 Alamo Group Inc. Parts Section 5-24 NH T6000 SABER[...]

TRACTOR REMOTE PLUMBING - OPEN CENTER Continued... ITEM PART NO. QTY. DESCRIPTION 1 06410171 1 PLATE,MOUNT 2 21986 4 LOCKWASHER,1/4" 3 21525 4 HEX NUT,1/4",NC 4 28583 2 CAPSCREW,8MM X 25MM,1.25P 5 6T2619 2 LOCKWASHER,8MM 6 34948 2 FLATWASHER,8MM 7 06503002 1 ADAPTER,12MM MOR X 5/16"MJ 8 06500092 1 HOSE,1/4" X 12" 9 06503012[...]

MIRROR BRACKET ©2011 Alamo Group Inc. Parts Section 5-26 NH T6000 SABER[...]

MIRROR BRACKET Continued... ITEM PART NO. QTY. DESCRIPTION 1 ------ 1 WORK LIGHT 2 ------ 1 KNOB T6010 3 ------ 1 MIRROR 4 ------ 1 EXHAUST 5 06370008 1 MNT,MIRROR/LIGHT 6 06410633 1 MNT,MIRROR 7 06410141 1 COLLAR,EXHAUST 8 06410142 1 COLLAR,CLAMP,EXHAUST 9 21530 2 CAPSCREW,1/4" X 1",NC 10 21525 4 HEX NUT,1/4",NC 11 22014 4 FLATWASHE[...]

POLYCARBONATE SAFETY WINDOW ©2011 Alamo Group Inc. Parts Section 5-28 NH T6000 SABER[...]

POLYCARBONATE SAFETY WINDOW Continued... ITEM PART NO. QTY. DESCRIPTION 1 064900 37 1 POLYCARBONATE,DOOR,RH 2 31965 17 TRIM SEAL,3/8"CLIP X 3/4"OD BULB (IN FEET) 3 06530502 2 CAPSCREW,8MM X 40MM,1.25P,GR8 4 ------ - EXISTING HARDWARE 5 06530501 1 CAPSCREW,6MM X 25MM,1.0P,GR8 6 06537006 1 THREADED INSERT,1/4" X 1/2",NC 7 21532 1 [...]

EXHAUST MOUNT - 6 CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 06410113 1 MNT,EXHAUST 2 06410121 1 MNT,EXHAUST,SUPPORT 3 06520023 1 TUBE,EXHAUST RELOCATE,6CYL 4 32986 2 CLAMP,EXHAUST,3-1/2" 5 21630 4 CAPSCREW,3/8" X 1",NC 6 21988 4 LOCKWASHER,3/8" 7 21625 4 HEX NUT,3/8",NC 8 ------ 2 EXISTING MAINFRAME HARDWARE ©2011 Alamo Gr[...]

BOOMREST ASSEMBLY - SABER ITEM PART NO. QTY. DESCRIPTION 1 06310071 1 BMRST,ASSY,SABER 2 06310090 1 STOP,UPPER,SBR 3 06310091 1 STOP,LOWER,SBR 4 06520078 4 BUMPER,PAD,SHORT 5 32686 1 BUMPER,PAD,LONG 6 28734 11 CAPSCREW,3/8" X 1",NC 7 6T1027 8 CAPSCREW,1/2" X 1-3/4",NC 8 06533004 16 FLATWASHER,1/2",NC 9 31580 8 HEX NUT,1/2&q[...]

BOOMREST ASSEMBLY - SABER MB ITEM PART NO. QTY. DESCRIPTION 1 06310092 1 BMRST,ASSY,SABER MB 2 06310090 1 STOP,UPPER,SBR 3 06310060 1 STOP,LOWER,SBR MB 4 06520078 4 BUMPER,PAD,SHORT 5 32686 1 BUMPER,PAD,LONG 6 28734 11 CAPSCREW,3/8" X 1",NC 7 6T1027 8 CAPSCREW,1/2" X 1-3/4",NC 8 06533004 16 FLATWASHER,1/2",NC 9 31580 8 HEX [...]

BOOMREST ASSEMBLY - SABER XB ITEM PART NO. QTY. DESCRIPTION 1 06310035 1 BOOMREST,BASE 2 06310053 1 BOOMREST,UPPER 3 06310054 1 BOOMREST,LOWER 4 06520078 4 WEARPAD,SHORT,BOOMREST 5 32686 1 WEARPAD,LONG,BOOMREST 6 06410587 2 CHANNEL,TIE DOWN 7 21747 4 CAPSCREW,1/2" X 9",NC 8 22004 12 FLATWASHER,1/2",NARROW 9 21727 8 NYLOCK NUT,1/2&quo[...]

WHEEL WEIGHT - SABER ©2011 Alamo Group Inc. Parts Section 5-34 NH T6000 SABER[...]

WHEEL WEIGHT - SABER Continued... ITEM PART NO. QTY. DESCRIPTION 1 32615 1 1700# WEIGHT 2 32518 2 850# WEIGHT 3 21846 3 CAPSCREW,3/4" X 9",NC 4 33626 3 FLATWASHER,3/4",USS 5 06530200 3 CAPSCREW,7/8" X 14",NC 6 06533000 6 FLATWASHER,7/8" 7 06531000 3 HEX NUT,7/8",NC 8 06401332 3 LOCK,BOLT,WHL WHT 9 06530219 3 CAPSC[...]

WHEEL WEIGHT - SABER MB/XB ©2011 Alamo Group Inc. Parts Section 5-36 NH T6000 SABER[...]

WHEEL WEIGHT - SABER MB/XB Continued... ITEM PART NO. QTY. DESCRIPTION 1 06770045 1 1700# WEIGHT,TAPPED 2 32518 2 850# WEIGHT 3 21846 3 CAPSCREW,3/4" X 9",NC 4 33626 3 FLATWASHER,3/4",USS 5 06530200 3 CAPSCREW,7/8" X 14",NC 6 06533000 6 FLATWASHER,7/8" 7 06531000 3 HEX NUT,7/8",NC 8 06401332 3 LOCK,BOLT,WHL WHT 9 [...]

NOTES 1 ©2011 Alamo Group Inc. Parts Section 5-38 NH T6000 SABER[...]

P ARTS SECTION COMMON SABER BOOM[...]

[...]

PART NAME INDEX PARTS ORDERING GUIDE ......................................................................................................................................................................... 5 BOOM SWIVEL ASSEMBLY ........................................................................................................................[...]

PART NAME INDEX LEFT HAND JOYSTICK SWITCHBOX SCHEMATIC ........................................................................................................................... 71 TROUBLESHOOTING ........................................................................................................................................................[...]

PARTS ORDERING GUIDE ©2011 Alamo Group Inc. Parts Section 6-5 COMMON SABER[...]

BOOM SWIVEL ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-6 COMMON SABER[...]

BOOM SWIVEL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION --- 32742 1 SWIVEL W/BUSHINGS,BOOM,SABER 1 32376 1 SWIVEL,BOOM,SABER,W/O BUSHING 2 33705 1 CYLINDER,3X17 1/2,WELDED 3 32381 1 PIN,2 1/2,SWIVEL,SABER 4 33710 1 PIN,CYLINDER,1,SWIVEL,SABER 5 32380 1 PIN,CYL,1,SWIVEL,SABER 6 32372 1 PIN,CYLINDER,STAGE,2ND 7 32378 1 PIN,BOOM TO SWIVEL,SAB[...]

QUICK COUPLERS ©2011 Alamo Group Inc. Parts Section 6-8 COMMON SABER[...]

QUICK COUPLERS Continued... ITEM PART NO. QTY. DESCRIPTION 1 34392 2 ADAPTER,1ORBX1FJX 2 06503028 2 QUICK COUPLER,1”SAE,MALE,FLAT 3 06503027 2 QUICK COUPLER,1”SAE,FEM,FLAT 4 33555 2 ADAPTER,1MORBX1MJIC 5 ------ - PREFORMED TUBES - REFER TO BOOM ARM PARTS 6 ------ - #16 HOSE - REFER TO HYDRAULICS PARTS ©2011 Alamo Group Inc. Parts Section 6-9 C[...]

SABER BOOM ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 32743 1 MAIN BOOM W/BEARING 2 32744 1 SECONDARY BOOM W/BEARING 3 32311 1 MOUNT,SWIVEL HEAD 4 32309 1 MOUNT HEAD PLATE 5 32316 1 LINKAGE,BOOM TO CYLINDER 6 32745 1 LINKAGE W/BEARING,CYLINDER TO SWIVEL ©2011 Alamo Group Inc. Parts Section 6-10 COMMON SABER[...]

SABER BOOM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 7 32363 1 CYLINDER,5" X 25" 8 32364 1 CYLINDER,4-1/2" X 26-1/2" 9 32365 1 CYLINDER,4" X 15" 10 33542 2 PREFORMED TUBE,1” 11 32627 2 PREFORMED TUBE,3/8” 12 32628 4 PREFORMED TUBE,3/8” 13 32629 4 PREFORMED TUBE,3/8” 14 33541 1 PREFORMED TUBE,1” (RO[...]

SABER MB BOOM ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 06310075 1 BOOM,MB,PRIMARY,SABER 2 06310076 1 BOOM,MB,SECONDARY,SABER 3 21688 5 CAPSCREW,7/16" X 3-1/4,NC 4 32375 3 PIN,1-1/2" X 3-13/16",W/HOLE 5 21677 8 NYLOCK NUT,7/16",NC 6 32363 1 CYLINDER,5" X 25" ©2011 Alamo Group Inc. Parts Section 6-12 COMMON SABER[...]

SABER MB BOOM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 7 32362 4 BEARING,DX,2" X 2" LONG 8 6T3211 8 GREASE ZERK,1/8" X STR 9 06506042 2 PRFRMD,1,MAIN,SABER MB 10 06506043 4 PRFRMD,2,MAIN,SABER MB 11 33215 7 TUBE CLAMP KIT 12 06506045 1 PRFRMD,4,MAIN,SABER MB (ROTARY RETURN) 13 06506044 1 PRFRMD,3,MAIN,SABER MB (ROTARY PRE[...]

SABER XB BOOM ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 06310031 1 BOOM,LONG,PRIMARY,SABER 2 06310032 1 BOOM,LONG,SECONDARY,SABER 3 21688 5 CAPSCREW,7/16" X 3-1/4",NC 4 32375 3 PIN,1-1/2" X 3-13/16",W/HOLE 5 21677 8 NYLOCK NUT,7/16",NC 6 32363 1 CYLINDER,5" X 25" ©2011 Alamo Group Inc. Parts Section 6-14 COMMON S[...]

SABER XB BOOM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 7 32362 4 BEARING,DX,2" X 2" LONG 8 6T3211 8 GREASE ZERK,1/8" X STR 9 06506029 2 PRFRMD,1,MAIN,SABER XB 10 06506030 4 PRFRMD,2,MAIN,SABER XB 11 33215 7 TUBE CLAMP KIT 12 06506032 1 PRFRMD,4,MAIN,SABER XB (ROTARY RETURN) 13 06506031 1 PRFRMD,3,MAIN,SABER XB (ROTARY PRE[...]

50IN FLAIL ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-16 COMMON SABER[...]

50IN FLAIL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ---- 06742138 1 FLAIL,BOOM,50,MD GRASS,CPLT ASSY (MEDIUM BRUSH/GRASS) 1 06320145 1 CUTTER HEAD BONNET 2 TF3004 1 FRONT SHIELD 3 06700115 1 TBF50 (MEDIUM BRUSH/GRASS KNIFE ASSY) 4 6T2419 24 HEX NUT,9/16”,NC,STOVER 5 41725.01 24 BUSHING,1"OD X 5/8"ID 6 06430122 48 SPACER (MED[...]

50IN FLAIL ASSEMBLY, PASS-THROUGH KNIVES ©2011 Alamo Group Inc. Parts Section 6-18 COMMON SABER[...]

50IN FLAIL ASSEMBLY, PASS-THROUGH KNIVES Continued... ITEM PART NO. QTY. DESCRIPTION --- 06742135 1 FLAIL,BOOM,50,CPLT ASSY 1 06320145 1 CUTTER HEAD BONNET 2 TF3004 1 FRONT SHIELD 3 33717 1 TBF50,CUTTERSHAFT,PASS THRU KNIVES 4 TF3405 1 GROUND ROLLER 5 TF3406 1 GROUND ROLLER TIE ROD 6 TB1006A 2 DEFLECTOR FLAP 7 TB1008 1 FLAP RETAINING BAR 8 TF3001 2[...]

50IN FLAIL DRIVE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-20 COMMON SABER[...]

50IN FLAIL DRIVE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06504013 1 MOTOR 2 TF3006 1 BELT GUARD 3 TF3043 2 SHEAVE 4 TF3013 1 BUSHING 5 TF3011 1 BUSHING 6 TF3034 1 IDLER PULLEY 7 TF3205 1 IDLER ARM 8 TF3206 2 IDLER PULLEY SPACER 9 TF3605 1 IDLER ARM PIN WITH ZERK 10 6T3004 1 R - CLIP 11 PT3611A 1 CLEVIS 12 32481 1 THREADED ROD 13 TF36[...]

SABER DIRECT DRIVE FLAIL ASSY ITEM PART NO. QTY. DESCRIPTION --- 06742086 1 BONNET,SBF50,DD,ASSY (LIGHT BRUSH) ---- 06742142 1 BONNET,SBF50,DD,ASSY (MEDIUM BRUSH) ©2011 Alamo Group Inc. Parts Section 6-22 COMMON SABER[...]

SABER DIRECT DRIVE FLAIL ASSY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06320112 1 BONNET 2 TF3007A 1 COVER PLATE 3 06410794 1 GUARD 4 06533006 14 FLATWASHER,1/2",GR 9 5 21727 10 NYLOCK NUT,1/2",NC 6 06530404 2 CAPSCREW,SKT/BUT HD,1/2" X 1-1/2",NC 7 06530401 4 CAPSCREW,SKT/BUT HD,1/2" X 1",NC 8 06320127 1 DOOR,SBF5[...]

SABER DIRECT DRIVE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-24 COMMON SABER[...]

SABER DIRECT DRIVE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 ------ - BONNET *REFER TO BONNET ASSY 2 06506040 1 PREFORMED TUBE 3 TF4852 2 FLANGE KIT 4 06530401 6 CAPSCREW,SKT/BUT HD,1/2" X 1",NC 5 06320126 1 MOTOR GUARD 6 06504003 1 MOTOR,DD 7 06500539 1 HOSE,1" X 82" 8 06530223 4 CAPSCREW,9/16" X 1-3/4",N[...]

63IN FLAIL ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-26 COMMON SABER[...]

63IN FLAIL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ------ 06200658 1 FLAIL,BOOM,63",GRASS,CPLT ASSY 1 06320110 1 CUTTER HEAD BONNET 2 28743 1 CUTTER SHAFT / KNIFE ASSY STANDARD GRASS ------ 28642C 1 CUTTER SHAFT,63",STD 3 TF1021B 36 FLAIL KNIFE MOUNTING BOLT 4 TF1020 36 FLAIL KNIFE MOUNTING CLEVIS 5 33713 72 FLAIL KNIFE - STA[...]

63IN FLAIL DRIVE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-28 COMMON SABER[...]

63IN FLAIL DRIVE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06504013 1 MOTOR (M350-1 3/4 GEAR) 2 28703B 1 BELT GUARD 3 TF3044 1 UPPER SHEAVE 4 TF3040 1 LOWER SHEAVE 5 TF3013 1 BUSHING 6 28723 1 BUSHING 7 28679B 1 MOTOR CHANNEL 8 PT3611A 1 CLEVIS 9 40496 1 THREADED ROD 10 28702 2 BELT 11 TF3620A 1 TENSIONER SPRING 12 28572 1 SQUARE KEY 1[...]

50IN SABER ROTARY MOWER ITEM PART NO. QTY. DESCRIPTION 1 33304 - ROTARY,SABER 50",ASSY 2 32914 1 ROTARY,SABER 50",DECK 3 32915 1 SHIELD,50" ROTARY,SABER 4 06504012 1 MOTOR 5 33198 1 MOTOR MOUNTING BRACKET 6 34479 1 SPROCKET,MOTOR 7 34482 1 CHAIN COUPLING 8 34483 1 COVER COUPLING 9 TF4852 2 FLANGE KIT 10 TF1124 1 KEY,WOODRUFF 11 33185[...]

50IN SABER ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 12 32952 2 DEFLECTOR FLAP 13 33211 1 RETAINING BAR,FLAP 14 32951 1 HINGE PIN,SHIELD 15 33924 2 ROLLPIN,HINGE PIN 16 32936 2 SKID SHOE 17 34509 1 BAR,KNIVE MOUNTING 18 33203 1 KNIVES,SET OF 2,ROTARY,3/4” 19 34883 2 BOLT,KNIFE 20 6T0822 3 SHIM,MOTOR MOUNT,THIN 21 6T0822A 3 SHIM,MOT[...]

50IN SABER XB ROTARY MOWER ITEM PART NO. QTY. DESCRIPTION --- 06741036 - ROTARY,SABER XB,ASSY 1 06320009 1 ROTARY,SABER XB,DECK 2 06410439 1 COVER,MOTOR MNT 3 22014 2 FLATWASHER,1/4" 4 21530 2 CAPSCREW,1/4" X 1",NC 5 33879 6 CAPSCREW,3/4" X 2-1/4",NF,GR 8 6 33880 6 FLATWASHER,3/4",GR 8,SAE 7 33984 2 PIN,SHIELD,50"[...]

50IN SABER XB ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 12 33785 1 CYL,1-1/2 X 8" 13 33778 1 HINGE PIN,50" RTRY 14 6T3017 2 ROLLPIN,3/16" X 1" 15 33754 1 SHIELD,50" RTRY 16 33777 2 SKID SHOE,50" RTRY 17 21993 6 LOCKWASHER,3/4",GR 8 18 6T2413 6 HEX NUT,3/4",NF,GR 8 19 6T1023R 2 KNIFE MTG NUT,1-1[...]

60IN SABER ROTARY MOWER ITEM PART NO. QTY. DESCRIPTION --- 06741072 - ROTARY,SABER 60",ASSY 1 06320169 1 ROTARY,SABER 60",DECK 2 33879 6 CAPSCREW, 3/4" X 2-1/4",NF GR 8 3 33880 6 FLATWASHER,3/4",GR 8,SAE 4 06410439 1 COVER,MOTOR MNT 5 22014 2 FLATWASHER,1/4” 6 21530 2 CAPSCREW,1/4" X 1",NC 7 RD1032 2 PIN,LYNCH,1[...]

60IN SABER ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 14 06420139 1 HINGE PIN,60" RTRY 15 06320162 1 SHIELD,60" RTRY 16 6T1024H5 1 SPINDLE 17 21993 6 LOCKWASHER,3/4",GR 8 18 6T2413 6 HEX NUT,3/4",NF,GR 8 19 06400690 1 BAR,BLADE,60” RTRY 20 33764 6 FLATWASHER,5/8",GR 8,SAE 21 6T2259 6 CAPSCREW,5/8" X 1-3[...]

60IN ROTARY KNIFE AND DISH OPTION ©2011 Alamo Group Inc. Parts Section 6-36 COMMON SABER[...]

60IN ROTARY KNIFE AND DISH OPTION Continued... ITEM PART NO. QTY. DESCRIPTION 1 34876 1 BLADE MOUNTING DISK 2 6T1023R 2 NYLOCK NUT,1-1/8” 3 34878 2 SPACER 4 34497 2 KNIFE MOUNTING BOLT 5 34684 2 GRASS KNIFE 6 33764 6 FLATWASHER 7 6T2259 6 CAPSCREW --- 27167 1 BOLT KIT (INCLUDES ITEMS 6 & 7) ---- 6T1825 1 LOCTITE - USED ON ALL DISK MOUNTING BO[...]

SABER SPINDLE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-38 COMMON SABER[...]

SABER SPINDLE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION --- 33219 - SPINDLE ASSY,ROTARY 1 34480 1 TAPERLOCK SPROCKET 2 21530 3 CAPSCREW,1/4” X 1”,NC 3 6T1015 2 BEARING LOCK NUT,THIN 4 22596 1 JAMWASHER 5 6T1014 1 BEARING ADJUST SLEEVE 6 6T1011 2 UPPER SEAL,SMALL 7 6T1012 1 BEARING CONE,SMALL 8 6T1013 1 BEARING CUP,SMALL 9 6T3210 1 GR[...]

SABER XB & 60IN SPINDLE ASSY ©2011 Alamo Group Inc. Parts Section 6-40 COMMON SABER[...]

SABER XB & 60IN SPINDLE ASSY Continued... ITEM PART NO. QTY. DESCRIPTION --- 6T1024H5 - SPINDLE ASSEMBLY 1 6T1031 1 SPROCKET 2 6T1016 1 BEARING LOCK NUT,THICK 3 22596 1 JAM WASHER 4 6T1015 1 BEARING ADJUSTMENT NUT,THIN 5 6T1014 1 BEARING ADJUSTMENT SLEEVE 6 6T1011 1 UPPER SEAL (SET OF 2) 7 6T1012 1 BEARING CONE 8 6T1013 1 BEARING CUP 9 6T1010H [...]

3IN X 17-1/2IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 33705 - CYLINDER,WELDED,3" X 17-1/2" 1 34571 1 PISTON ROD ASSY 2 34572 1 BUTT & TUBE ASSY 3 34573 1 PISTON 4 34574 1 GLAND 5 34575 1 LOCK NUT,1"-14 UNS (TORQUE TO 315 FT.LB.) 6 34576 1 SPACER 7 34577 1 CHECK VALVE,KEPNER 8 34578 1 ORIFICE 9 33761 1 SEAL K[...]

4IN X 15IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 32365 - CYLINDER,WELDED,4" X 15" 1 34580 1 PISTON ROD ASSY 2 34581 1 BUTT & TUBE ASSY 3 34582 1 PISTON 4 34583 1 GLAND 5 34584 1 LOCK NUT,1-1/4"-12 UNF (TORQUE TO 510 FT.LB.) 9 33757 1 SEAL KIT,PACKING (ITEMS 12 THRU 19) 10 ------ 2 GREASE ZERK 12 ------ 1 O [...]

4-1/2IN X 26-1/2IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 32364 - CYLINDER,WELDED,4-1/2" X 26-1/2" 1 34586 1 PISTON ROD ASSY 2 34587 1 BUTT & TUBE ASSY 3 34588 1 PISTON 4 34589 1 GLAND 5 34590 1 LOCK NUT,1-1/4"-12 UNF (TORQUE TO 510 FT.LB.) 9 33758 1 SEAL KIT,PACKING (ITEMS 12 THRU 19) 10 ------ 2 GREASE ZER[...]

5IN X 25IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 32363 - CYLINDER,WELDED,5" X 25" 1 34592 1 PISTON ROD ASSY 2 34593 1 BUTT & TUBE ASSY 3 34594 1 PISTON 4 34595 1 GLAND 5 34596 1 LOCK NUT,1-3/4"-12 UNF (TORQUE TO 1800 - 2000 FT.LB.) 7 34597 1 CHECK VALVE,KEPNER 8 34598 1 ORIFICE 9 33759 1 SEAL KIT,PACKING (I[...]

PUMP AND GRILL GUARD OPTIONS ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 32737 1 UNIVERSAL GRILL GUARD 3 21833 4 CAPSCREW,3/4" X 2-1/4",NC 4 22021 2 FLATWASHER,3/4" 5 21993 4 LOCKWASHER,3/4" 6 21825 4 HEX NUT,3/4",NC ©2011 Alamo Group Inc. Parts Section 6-46 COMMON SABER[...]

RESERVOIR TANK FILTER ASSEMBLY ITEM PART NO. QTY. DESCRIPTION ------ 06505044 - FILTER ASSY SAE 10 MICRON 1 28583 4 CAPSCREW,8MM X 25MM(1.25 PITCH) 2 06505045 1 COVER 3 06505046 1 SEAL KIT 4 06505047 1 SPRING 5 06505048 1 BYPASS 6 35259 1 FILTER,10 MIC,RETURN LINE 7 06505049 1 CAN/BODY ©2011 Alamo Group Inc. Parts Section 6-47 COMMON SABER[...]

FRONT HYDRAULIC PUMP ©2011 Alamo Group Inc. Parts Section 6-48 COMMON SABER[...]

FRONT HYDRAULIC PUMP Continued... ITEM PART NO. QTY. DESCRIPTION --- 23152 1 PUMP ASSEMBLY,1-3/4”,COMPLETE 1 22766 1 SHAFT END COVER 2 22779 1 PORT END COVER 3 22774 1 GEAR HOUSING,1-3/4” 4 22771 1 GEAR SET 5 23824 4 CAPSCREW 6 06504078 2 SCREW,DRIVE 7 22773 4 DOWEL PINS 8 06504077 1 NAMEPLATE 9 02965611 2 THRUST PLATE 10 22767 1 PLUG 11 065040[...]

50IN AND 63IN FLAIL MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-50 COMMON SABER[...]

50IN AND 63IN FLAIL MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION ------ 06504013 - MOTOR ASSEMBLY 350 1 06504039 1 SHAFT END COVER 2 06504040 1 PORT END COVER 3 06504041 1 GEAR HOUSING 4 06504042 1 MATCHED GEAR SET 5 TF4402 1 BALL BEARING 6 06504043 4 CAP SCREW 7 06504044 2 SET SCREW 8 06504028 1 KEY 9 06504045 4 DOWEL PIN 10 ------ [...]

50IN FLAIL DIRECT DRIVE MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-52 COMMON SABER[...]

50IN FLAIL DIRECT DRIVE MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION --- 06504003 - MOTOR ASSEMBLY,DIRECT DRIVE 1 06504039 1 HOUSING,SEC 2 06504040 1 HOUSING,PEC 3 06504041 1 HOUSING,GEAR 4 06504117 1 GEAR,SET 5 06504118 1 SHAFT,CONTINENTAL 6 TF4402 1 BRG,BALL 7 06504043 4 CAPSCREW 8 06504044 2 SCREW,DRIVE 9 06504045 4 PIN,DOWEL 10 0[...]

50IN AND 60IN ROTARY MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-54 COMMON SABER[...]

50IN AND 60IN ROTARY MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 06504011 - MOTOR ASSEMBLY,TRB60 06504012 - MOTOR ASSEMBLY,TRB50 1 22790 1 HOUSING, SEC 2 06504088 1 HOUSING, PEC 3 06504062 1 HOUSING, GEAR,TRB60 ------ 06504089 - HOUSING, GEAR,TRB50 4 06504090 1 SET, GEAR SHAFT 5 06504104 4 CAP SCREW,TRB60 ------ 06504091 - CAP SCREW[...]

COOLER ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-56 COMMON SABER[...]

COOLER ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 21530 10 CAPSCREW,1/4 X1 NC 2 21986 10 LOCKWASHER,1/4 3 22014 10 FLATWASHER,1/4 4 35176 10 1/4 U-NUT 5 06370015 1 SCREEN,COOLER,FRNT 6 06380006 1 MNT,COOLER,BUMPER TANK,RH 7 06380007 1 MNT,COOLER,BUMPER TANK,LH 8 06510026 1 COOLER,FRONT MNT 9 21629 4 CAPSCREW,3/8 X 3/4 NC 10 21988 4 LOCK[...]

CABLE (MANUAL) LIFT VALVE, 4 SPOOL - 06502104 ©2011 Alamo Group Inc. Parts Section 6-58 COMMON SABER[...]

CABLE (MANUAL) LIFT VALVE, 4 SPOOL - 06502104 Continued... ITEM PART NO. QTY. DESCRIPTION --- 06502104 - VALVE,MANUAL,4 SPOOL,LOAD SENSE 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 5 31600 1 VALVE SECTION (DOUBLE ACTING, DETEN[...]

CABLE (MANUAL) LIFT VALVE, 5 SPOOL - 06502103 ©2011 Alamo Group Inc. Parts Section 6-60 COMMON SABER[...]

CABLE (MANUAL) LIFT VALVE, 5 SPOOL - 06502103 Continued... ITEM PART NO. QTY. DESCRIPTION --- 06502103 - VALVE,MANUAL,5 SPOOL,LOAD SENSE 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 5 31597 1 VALVE SECTION (DOUBLE ACTING, CENTE[...]

5 SPOOL ELECTRONIC VALVE - 06502096 ITEM PART NO. QTY. DESCRIPTION ------ 06502096 - VLV,5SP,32PVG,SIDE STOW 1 06502074 1 END PLATE 1S 06505013 1 END PLATE SEAL KIT 2 ------ 5 BONNET 2S 06505042 1 BONNET SEAL KIT 2A 42197 1 MAIN BOOM BONNET 2B 42197 1 SECONDARY BOOM BONNET 2C 42197 1 DECK ROLL BONNET 2D 42197 1 BOOM SWIVEL BONNET 2E 42197 1 DECK SH[...]

5 SPOOL ELECTRONIC VALVE - 06502096 Continued... ITEM PART NO. QTY. DESCRIPTION 3 34308 1 INLET SECTION 3S 06505013 1 INLET SECTION SEAL KIT 4 ------ 5 ELECTRONIC ACCUATOR 4A 06502101 1 MAIN BOOM ELECTRONIC ACCUATOR 4B 06502101 1 SECONDARY BOOM ELECTRONIC ACCUATOR 4C 06502100 1 DECK ROLL ELECTRONIC ACCUATOR 4D 06502101 1 BOOM SWIVEL ELECTRONIC ACCU[...]

BRAKE VALVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION * 06510084 - BRAKE VALVE, ASSY 1 34092 1 BRAKE VALVE, BLANK 2 34094 2 LOGIC ELEMENT 3 34090 1 RELIEF VALVE, 3500 PSI 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 6 34091 1 RELIEF VALVE, 2600 PSI ©2011 Alamo Group Inc. Parts Section 6-64 COMMON SABER[...]

BRAKE VALVE HYDRAULIC SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-65 COMMON SABER[...]

SOLENOID SWITCH BOX AND WIRING ITEM PART NO. QTY. DESCRIPTION 1 ------ - SWITCH BOX 2 RE37651 1 PLUG,AUX PWR 3 24204 - FUSE HOLDER,IN-LINE (OPTION) 4 6T3965 - FUSE,3AMP (OPTION) 5 6T3934 - TEMPERATURE GAUGE (OPTION) 6 6T3931 - TEMPERATURE SENSOR (OPTION) ©2011 Alamo Group Inc. Parts Section 6-66 COMMON SABER[...]

MANUAL LIFT VALVE SWITCH BOX ITEM PART NO. QTY. DESCRIPTION 1 06514012 1 SWBX,ALUM,BLK,06510100 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 33811 1 SWITCH,MASTER/DECK FLOAT 4 34532 1 SWITCH,TRVL LCK 5 06514014 1 BREAKER,10A,SWBX 6 6T3923 1 INDICTATOR LIGHT,ON,RED 7 34540 1 STRAIN RELIEF,3/4,BLACK,NYLON 8 06550019 1 DECAL,SWTCHBX,BOOM,CG 9 02964063 1 KNOB,R[...]

MANUAL LIFT VALVE SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-68 COMMON SABER[...]

ELECTRONIC LIFT VALVE SWITCH BOX ITEM PART NO. QTY. DESCRIPTION 1 06510196 1 SWBX,ASSY 2 33811 2 SWITCH,MASTER/DECK FLOAT 3 33813 1 SWITCH,SFTY SHIELD 4 34532 1 SWITCH,TRVL LCK 5 34540 1 STRAIN RELIEF,3/4",BLACK,NYLON 6 6T3923 1 INDICTATOR LIGHT,ON,RED 7 06514006 1 BREAKER,15A,SWBX 8 06550044 1 DECAL,SWBX,06510047 9 35226 1 SWITCH,MOWER,COLEHE[...]

ELECTRONIC LIFT VALVE SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-70 COMMON SABER[...]

LEFT HAND JOYSTICK SWITCHBOX SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-71 COMMON SABER[...]

TROUBLESHOOTING ©2011 Alamo Group Inc. Parts Section 6-72 COMMON SABER[...]

TROUBLESHOOTING - CONTINUED ©2011 Alamo Group Inc. Parts Section 6-73 COMMON SABER[...]

HYDRAULIC TROUBLESHOOTING GUIDE ©2011 Alamo Group Inc. Parts Section 6-74 COMMON SABER[...]

ELECTRICAL TROUBLESHOOTING GUIDE ©2011 Alamo Group Inc. Parts Section 6-75 COMMON SABER[...]

NOTES 1 ©2011 Alamo Group Inc. Parts Section 6-76 COMMON SABER[...]

CLEAN CUTTER HEAD ©2011 Alamo Group Inc. Parts Section 6-77 COMMON SABER[...]

CLEAN CUTTER ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-78 COMMON SABER[...]

CLEAN CUTTER OPERATION ©2011 Alamo Group Inc. Parts Section 6-79 COMMON SABER[...]

CLEAN CUTTER OPERATION - CONTINUED ©2011 Alamo Group Inc. Parts Section 6-80 COMMON SABER[...]

CLEAN CUTTER MAINTENANCE ©2011 Alamo Group Inc. Parts Section 6-81 COMMON SABER[...]

CLEAN CUTTER BLADE AND TEETH PARTS ITEM PART NO. QTY. DESCRIPTION 1 06420025 1 ADAPTER,SAW,SABER,RNFRCD 2 06520224 1 BLADE, 48” SAW WITH TEETH 3 06420038 1 COLLAR,SAW,SABER 4 33380 6 FLATWASHER,3/4",GR8,SAE 5 06530210 6 CAPSCREW,5/8" X 3-3/4",NF,GR 8 6 06520225 30 TOOTH WITH RIVET, SAW BLADE 7 34703 30 TOOTH RIVET, SAW BLADE --- 34[...]

CARBIDE TIP REPLACEMENT ©2011 Alamo Group Inc. Parts Section 6-83 COMMON SABER[...]

NOTES 2 ©2011 Alamo Group Inc. Parts Section 6-84 COMMON SABER[...]

FIRE SUPRESSION SYSTEM ©2011 Alamo Group Inc. Parts Section 6-85 COMMON SABER[...]

FIRE SUPRESSION SYSTEM PARTS ©2011 Alamo Group Inc. Parts Section 6-86 COMMON SABER[...]

FIRE SUPRESSION SYSTEM PARTS Continued... ITEM PART NO. QTY. DESCRIPTION 1 06520357 1 TANK,FIRE SUPRESS SYS,RAILKUT 2 06520358 1 MNT,TANK,FIRE KIT,RAILKUT 3 06520359 1 PUMP,FIRE SUPRESS SYS,RAILKUT 4 6T2181 4 CAPSCREW,SKT HD,10/24 X 3/4 5 24890 4 HEX NUT,10-24 NYLOCK 6 06520360 1 HOSE REEL,FIRE KIT,RAILKUT 7 21630 4 CAPSCREW, 3/8 X 1,NC 8 21627 8 N[...]

FIRE SUPRESSION SYSTEM ELECTRICAL SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-88 COMMON SABER[...]

WETCUT ©2011 Alamo Group Inc. Parts Section 6-89 COMMON SABER[...]

WETCUT 50 GALLON TANK MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06370136 1 MNT,TANK,50GAL,WETCUT 4 06520342 1 TANK,50GA.,WETCUT 7 RD1032 3 PIN,LYNCH 1/4" X 2" 8 TB1036 1 PIN,SEC BOOM SWIV 1X4-11/16" 9 06520343 4 ANCHOR,STRAP,WETCUT 10 06520344 4 BOLT,STRAP,TANK,WETCUT 11 06520345 2 STRAP,TANK,WETCUT ©2011 Alam[...]

WETCUT 100 OR 150 GALLON TANK MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06370138 1 MNT,TANK,100GAL,WETCUT ------ 06370139 - MNT,TANK,150GAL,WETCUT 4 06520372 1 TANK,100GA.,WETCUT ------ 06520373 - TANK,150GA.,WETCUT 5 21527 2 HEX NUT,NYLOCK,1/4" NC 6 21530 2 CAPSCREW,1/4" X 1" NC 7 RD1032 3 PIN,LYNCH 1/4" [...]

WETCUT TANK PLUMBING ©2011 Alamo Group Inc. Parts Section 6-92 COMMON SABER[...]

WETCUT TANK PLUMBING Continued... ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06520336 1 CNTRLR,SENSOR,06520333 3 06520341 1 PUMP,WETCUT 4 06520346 1 FITTING,BULKHEAD,WETCUT 5 06520347 1 FITTING,ELBOW,WETCUT 6 06520348 1 VLV,BALL,WETCUT 7 06520349 6 FITTING,BARB,HOSE,WETCUT 8 06520352 4 FITTING,NIPPLE,1/2X3/8,WETCUT 9 06520353 1 FITT[...]

WETCUT SPRAYER HEAD ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-94 COMMON SABER[...]

WETCUT SPRAYER HEAD ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06370105 1 HOOD,SPRAYER 2 06370106 1 HINGE,LH,SPRAYER 3 06370107 1 HINGE,RH,SPRAYER 4 06370108 1 HINGE,CNTR,SPRAYER 5 06410668 1 GUARD,SPRAYER,WETCUT 6 06410753 1 MNT,RH,WET CUT 7 06410754 1 MNT,LH,WET CUT 8 06410796 1 GUARD,HOSE,WETCUT 9 06420069 3 PIN,HINGE,WET CUT 10 0649[...]

WETCUT CABLES ©2011 Alamo Group Inc. Parts Section 6-96 COMMON SABER[...]

W ARRANTY SECTION Warranty Section 7-1[...]

.[...]

W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrant s to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship. Any part of equipment that in T iger ’ s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the [...]

ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator . Remember , SAFETY IS YOU! Y our safety an[...]

T O THE OWNER / OPERA TOR / DEALER T o keep your implement running ef ficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health A[...]

Printed in USA © T iger Corporation[...]