English dropdown-ico

Varimixer 60 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Varimixer 60, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Varimixer 60 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Varimixer 60. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Varimixer 60 should contain:
- informations concerning technical data of Varimixer 60
- name of the manufacturer and a year of construction of the Varimixer 60 item
- rules of operation, control and maintenance of the Varimixer 60 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Varimixer 60 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Varimixer 60, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Varimixer service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Varimixer 60.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Varimixer 60 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    THE PROGRAMMABLE CONTROL SYSTEM MK-IV User’s Manual[...]

  • Page 2

    [...]

  • Page 3

    General descriptions MODES The system contains six different modes: 1. MANUAL MODE: The mode when the mixer is operated like a man - ual controlled mixer. Instead of executing a programmed recipe, the mixer is started and operated until it is manually shut off. 2. PROGRAMMING MODE: The mode where all programming and editing takes place. 3. PROGRAM [...]

  • Page 4

    The Keypad The Keypad is used for entering data to the system. ITEM FUNCTION EXPLANATION 1. Program No. Displays the program Number being executed. 2. Step Displays the step number being executed. 3. Speed Displays the set-speed. 4. Time Displays the elapsed time since start or displays the remaining time to shut down. 5. Text Area OVERLOAD: MIxer [...]

  • Page 5

    6. Enter Used for stepping through a program. 7. CLR 8. Speed up/down arrows. 9. Time up/down arrows. 10. Program 11. Pause 12. Numeric keys 13. Emergency Stop Clears a flashing display. Used for adjusting the the speed while the mixer is running. Used for adjusting the the time. Used to enter/exit program-programming mode. Pauses the mixer without[...]

  • Page 6

    How to run the mixer manually. SPEED Mode. Enter the speed desired. Push Enter the time desired. Push Push How to input a program. A flashing display indicates that it is expecting the operator to key in a value. A step is always a combination of speed and time. An example is 100 R.P.M. for 5:00 minutes or 0 R.P.M. for 15 seconds (which is a 15 sec[...]

  • Page 7

    To program a recipe. Push Push Enter the speed desired. “HOLD FOR 3 SECONDS” Repeat this process for as many as 9 steps per program, after the 9th step , the next program num - ber will display, ready to enter a new recipe.This will continue up to 25 programs. Push Push Enter the time desired. Example To edit a recipe or to correct mistakes, us[...]

  • Page 8

    To run a programmed recipe. Push Push Enter the Program number. Push After the ENTER key has been pushed, the data in step 1 will be displayed along with the program number. After the last program step has been executed, the mixer will slow to minimum speed and shut off. The mixer can be stopped at any time during a recipe by using the “PAUSE” [...]

  • Page 9

    To enter “FIXED MODE” Push Push “99” “HOLD FOR 3 SECONDS” Push Push “1 2 3 4” Push Push the program number. Push To exit “FIXED MODE” Push “HOLD FOR 3 SECONDS” Push “1 2 3 4” Push 7[...]

  • Page 10

    Control Data for Program 26 Program 26 contains the control data required by the computer to operate. This data differs from model to model. To access Program 26. Push “HOLD FOR 3 SECONDS” Push Push “26” Push “1 2 3 4” Push Push until you reach Step 7. Enter the value on the following chart that matches the mixer model. Repeat for step [...]

  • Page 11

    A D In the electronics fail. It is possible to bypass the control system if the electronics fail. Please note, when the system is bypassed, the safety devices do not operate. Extreme care should be taken when operating the mixer. 1. Switch off the main power. 2. Open the top lid, flip the dip switch (B) on the back of the computer control from “A[...]

  • Page 12

    E:401 E:301 E:201 Error Codes A error in the mixer will trigger an ERROR code in the time display. See the chart below for an explanation of error codes and the procedure for correcting them. E:201 The servo motor block actuator (B) did not contact the minimum speed microswitch (A) after the stop button was pushed or the programmed recipe completed[...]

  • Page 13

    E:301 There is no signal from the speed pickup (hall effect sensor). To correct this error: 1) Check that the sensor (D) is centered directly above the track of the 3 magnets (F) on the pulley and the gap between the sensor and magnets is 1/16”. If not , bend and / or move the bracket (I) holding the sensor. 2) Inspect the three wires between the[...]

  • Page 14

    E:4:01 The values in program 26 steps 7, 8 and 9 are missing or incorrect. To correct this error: Push “HOLD FOR 3 SECONDS” Push Push “26” Push “1 2 3 4” Push Push until you reach Step 7. Enter the value on the following chart that matches the mixer model. Repeat for step 8 and 9. Step 7 Mixer Model W30 W40 W60 W80 W100 W150 Cinnabon 40[...]

  • Page 15

    MAINTENANCE AND ADJUSTMENTS Computer Control 2 Fuses: 8 Amp 6.3 x 32 MM P.N. 20E-418.1 Power Supply 1 Fuse:1.5 Amp 6.3 x 32 MM P.N. 20E-418 Fuse data and component location Hall Effect Sensor P.N. 30E-500M Bowl Lift Servo Motor (If equipped) P.N. 100N-86.02 Speed Servo Motor P.N. 60E-517.02 Bowl Lift Microswitches (PN 61-522) Each 13[...]

  • Page 16

    Models W30, W40, W40P, W60,W60P Bowl adjustments W30 = 6 3/8” W40 = 6 3/8” W60 = 7” 14[...]

  • Page 17

    Bowl adjustments Models W80, W100, W150N W80 = 9 1/8” W100 = 11 5/8” W150 = 11 7/8” 15[...]

  • Page 18

    Lubrication White Lithium Grease (IE Lubriplate ) Nye Fluorocarbon Gel 868VH Order from authorized service agent Part number: WHITE GREASE 16[...]

  • Page 19

    Belt adjustments 17 NEVER move the base for motor ( R )(in the oblong holes) , this is a factory setting and is NOT used to tighten the belts.If the entire unit is to be exchanged, reference the below table. Models W30-W40(P) Distance (B) 11 1/2 inches Models W60-W150 Distance (B) 12 1/4 inches 1. Start by tightening the V-belts (C) . 1. A) Loosen [...]

  • Page 20

    Belt Exchange 18 1. Loosen Bolt (J) and remove washers (H). 2 2. Remove cotterpin (T) and dowel pin (E) from servo linkage. 2 . 3. Remove vari drive belt (A) from pulleys. 2 4. Remove Hall Effect sensor (X) from the rear of the computer. 3 5. Loosen bolts (D) and remove the front v-belts (C) by tilting the center pul .... ley assembly (L) forward a[...]

  • Page 21

    Belt Exchange 19[...]

  • Page 22

    Adjustment of low and high speed microswitches. 20[...]

  • Page 23

    Adjustment of low and high speed microswitches. 21[...]

  • Page 24

    Speed Servo System Figure Number Description W30, W40 , W40P W80, W100 , W150 1..........................Sensor..........................30E-500M.........................30E-500M 2..........................Bolt M6.................. ......STA 5432.........................STA 5432 3..........................Magnets.......................30E-515M.....[...]

  • Page 25

    Speed Servo System 23[...]

  • Page 26

    Power Supply Figure Number Description All Models 1..........................Transformer..............................................................60E-430 2..........................Filter....................................................................... . ..20E-419 3..........................Relay 24VDC.....................................[...]

  • Page 27

    Power Supply 1 2 3 4 5 6 7 8 9 11 10 25[...]

  • Page 28

    26[...]

  • Page 29

    27[...]

  • Page 30

    Power Supply Wiring Diagram 1.5 Amp 28[...]

  • Page 31

    [...]

  • Page 32

    5489 Campus Drive Shreveport LA 71129 (800) 222-1138 (318) 635-3131 Fax[...]