Delta 36-714 manual

INSTRUCTION MANUAL Delta 10" Hybrid Saw (Model 36-714) P ART NO. A08139 - 11-12-04 Copyright © 2004 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). NOTE: Shown with BC30 30” [...]

2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop[...]

3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf[...]

4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA[...]

5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this m[...]

6 6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before conn[...]

EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized c[...]

CAR TON CONTENTS Fig. 1 Parts 1. Cast Iron Extension Wings (2) 2. Switch Assembly 3. Fence Holder Brackets (2) 4. Drive Belt 5. T able Insert 6. Wr ench Hook 7. Miter Gage Holder 8. Splitter Mounting Bracket 9. Blade Hex Nut 10. Blade Flange 11. 10” Carbide- Tipped Blade 12. Blade W renches (2) 13. 4mm Hex Wr ench 14. Dust Port 15. Locking Knobs [...]

9 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be r emoved with a soft cloth moistened with kerosene (do not us e acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surface[...]

10 Fig. 4 DISCONNECT MACHINE FROM POWER SOURCE. T o bolt the saw to a permanent location, remove the nine screws which secur e the dust chute inside the saw cabinet, six of which are shown at (C) Fig. 4. Also, remove the side panel below the motor cover by loosening all six screws (D). Find the holes (E) Fig. 5 in the bottom of the saw and mark the[...]

DISCONNECT MACHINE FROM POWER SOURCE. First, lift motor and remove foam packing block fr om around motor . While lifting motor (A) Fig. 8, place a 10-12 inch long piece of 2x4, or another similar thickness of wood, (B) Fig. 8 as shown. This will help prop up the motor and will make it easier to install the grooved belt, (C) Fig. 8A. Place grooved b[...]

12 Fig. 10 DISCONNECT MACHINE FROM POWER SOURCE. Assemble left extension wing (A) Fig. 10A to the saw table. Align the three holes in the extension wing with the three holes (A) Fig. 9 in the side of the saw table. Place a 7/16" lockwasher , then a 7/16" flat washer on a 7/16- 20x1-1/4” hex head screw (all shown at (B) Fig. 9). In ser t[...]

13 INST ALLING THE SWITCH DISCONNECT MACHINE FROM POWER SOURCE. 1. Place switch (A) Fig. 11, behind the lip of extension wing (B). Insert M8x30 hex head screw (C) thr ough wing and then switch support. Place an M8 flat washer and an M8 lock washer on the screw . Thread an M8 hex nut (D) onto screw and tighten nut secur ely . 2. Insert switch cord w[...]

14 ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE . MAKE SURE BLADE IS NOT A TT ACHED. IF IT IS, REMOVE THE SAW BLADE FROM THE SA W USING THE SUPPLIED WRENCHES. 1. Fasten the r ear splitter mounting bracket (A) Fig. 15, to the rear trunnion on the back of the saw using the two 1/4”-20 x 3/4 ″ hex head screws [...]

15 5. If alignment is necessary , loosen the two screws (F) Fig. 18, align bracket (D) with the inner arbor flange (E), and tighten screws (F). 6. Loosely assemble large washer and scr ew (C) Fig. 18, to the inside splitter bracket. This screw and washer was removed in STEP 3 . 7. Assemble the blade guar d and splitter assembly (G) Fig. 19 between [...]

16 SAW BLADE DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the saw blade arbor to its maximum height. Assemble the saw blade (C) Fig. 23 to the saw arbor making sure the teeth of the blade point down towards the fr ont of the table, as shown in Fig. 23. Assemble the flange (D) and arbor nut (E) to the saw arbor and tighten arbor nut (E) as far as [...]

17 Fig. 26 L P INST ALLING T ABLE INSER T DISCONNECT MACHINE FROM POWER SOURCE. Lower saw blade and install table insert (P) Fig. 26, in the saw table. IMPORT ANT : When installing the table insert, make certain to hold on to the blade guard (L). The insert will automatically release the holding action on the splitter and lower the blade guard when[...]

18 ASSEMBLING MITER GAGE DISCONNECT MACHINE FROM POWER SOURCE Place a flat washer (A) Fig 30 on the threads of the miter gage lock handle (B) and then thread the handle into the hole (C) in miter gage bar . Inster plate (D) Fig.41 into the miter gage slot (E) Fig. 41 and slide miter gage onto saw table. Fig. 30 OPERA TION ST AR TING AND STOPPING SA[...]

19 Fig. 33 C Fig. 34 E D ADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPS The machine is equipped with positive stops that will quickly and accurately position the saw blade at 90° and 45° to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the blade guard and splitter . 2. Ra[...]

20 Fig. 38 A B D C BACKLASH ADJUSTMENTS DISCONNECT MACHINE FROM POWER SOURCE. After a period of extended use, if any play is detected in the blade raising or blade tilting mechanisms, remove the blade and make the following adjustments: ADJUSTING BLADE RAISING MECHANISM - Loosen locknut (A) Fig. 38, and turn eccentric sleeve (B) until all play is r[...]

21 MITER GAGE OPERA TION AND ADJUSTMENT The miter gage is equipped with adjustable index stops at 90, 75, 60,45 and 30 degrees. T o rotate the miter gage, loosen lock knob (A) Fig. 40, push the thumb lever (B) down and move the body of the miter gage (C) to the desired angle. The miter gage is equipped with a plate (D) Fig.41 which fits into the T [...]

22 WHEN USING THE BLOCK (B) FIG. 44, AS A CUT -OFF GAGE, IT IS VERY IMPORT ANT THA T THE REAR END OF THE BLOCK BE POSITIONED SO THE WORK PIECE IS CLEAR OF THE BLOCK BEFORE IT ENTERS THE BLADE. CROSS-CUTTING Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the ga[...]

23 Ripping is cutting lengthwise through a boar d, (Fig. 45). NOTE : Be sure the material to be cut is seasoned, dry and flat. The rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must have a strai[...]

24 Fig. 49 Fig. 51 Fig. 50 H G USING MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.The many differ ent knife shapes available make it possible for the operator to produce almost any kind of mouldings, such as various styles of corner [...]

25 Fig. 56 Fig. 54 Fig. 55 Fig. 53 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 53). V arious combinations of saws and cutters are used to cut grooves fr om 1/8 ″ to 13/16 ″ for use in shelving, making joints, tenoning, grooving, etc. The [...]

26 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). Fig. 59, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should [...]

27 When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 78. Fig. 78 PUSH STICK MAKE FROM 1/2 " OR 3/4 " WOOD OR THICKNESS LESS THAN WIDTH OF MA TERIAL TO BE CUT CUT OFF HERE TO PUSH 1/4 " WOOD CUT OFF HERE TO PUS[...]

28 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra[...]

29 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with [...]

30 NOTES[...]

31 NOTES[...]

The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T[...]