Electrolux E48GC76EPS manual

Installation Instructions Slide In Gas Cooktop 5995447 1 08 E36GC76EPS E48GC76EPS[...]

2 Safety IMPORT ANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a W arning or Caution based on the risk type. Definitions This is the safety alert symbol. It is used to alert you to potential pers[...]

3 WARNING WARNING WARNING WARNING WARNING • Read all instructions before using the appliance. • Improper installation, adjustment, alteration, service, or maintenance can cause personal injury or property damage. Refer to these instructions and the accompanying Use & Care Manual. For assistance or additional information, consult a qualified[...]

4 Safety WARNING WARNING WARNING WARNING WARNING • Based on safety considerations, the top burner flame should be adjusted so it does not extend beyond the edge of the cooking utensil. • If the information in this manual is not followed exactly , a fire or explosion may result causing property damage, personal injury , or death. • What to do [...]

5 Finding Information READ AND SA VE THESE INSTRUCTIONS Read all instructions before installing the cooktop. For your safety , please read and observe all safety instructions. This guide will help you anticipate all installation connections. QUESTIONS? For toll-free telephone support in the U.S. and Canada: 1-877- 4ELECTROLUX (1-877-435-3287) For o[...]

6 Finding Information TABLE OF CONTENTS Safety ..................................................................... 2 De fi ni ti on s ........................................................... 2 Important Safety Instructions ............................... 2 Safety Precautions .............................................. 3 Finding Information [...]

7 Prep aring for Inst allation VERIFY P ACKAGE CONTENTS • Literature Pack • Griddle • Bolts/W ashers • Simmer Plate • Burner Grate Pack • W ok Sta nd • Burner Set • S tainless S teel Cleaner • Gas Pressure Regulator • LP Conversion Kit • Burner Cap Pack CABINET/COUNTERT OP PREP ARA TION The installation of this built-in applia[...]

8 Prep aring for Inst allation Plan the installation so that the electrical connection, gas shut-off valve, and pressure regulator are accessible from the front of the cabinet and so that all of the minimum required dimensions are provided. Dimensions apply to both models unless otherwise stated (see Figure 1). Locate the electrical supply box with[...]

9 Prep aring for Inst allation Provide an opening in the countertop as shown (see Figures 2, 3, 4, 5 and 6). Position the cutout so that minimum clearances are met. Figure 2[...]

10 Prep aring for Inst allation[...]

11 Making the Gas/Electric Connection REQUIREMENTS Gas Supply Requirements Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/NFP A 54. Be certain that the appliance being installed is correct for the gas s[...]

12 WARNING WARNING WARNING WARNING WARNING Severe shock, or damage to the cooktop may occur if the cooktop is not installed by a qualified installer or electrician. CA CA CA CA CA UTION UTION UTION UTION UTION Any additions, changes or conversions required in order for this appliance to satisfactorily meet the application needs must be made by a qu[...]

13 IMPOR IMPOR IMPOR IMPOR IMPOR T T T T T ANT ANT ANT ANT ANT • If the electrical supply circuit does not have a grounding-type receptacle, it is the responsibility of the customer to have the existing receptacle changed by an electrician to a properly grounded receptacle. • The power supply must be properly polarized. Reverse polarity will re[...]

14 Inst allation INST ALLING THE COOKTOP Place and center the cooktop within the cutout. Secure the cooktop to the countertop utilizing the two (2) 1/4-20 bolts provided. Do not overtighten the screws. CONNECTING THE GAS Attach the gas pressure regulator (included with the cooktop) to cooktop pipe nipple inlet. Install a gas shut-off valve (not inc[...]

15 Inst allation GAS AND ELECTRIC REQUIREMENTS TABLE The required voltage, frequency and amperage ratings are listed on the product data plate outside on the cooktop bottom. The gas and electric requirements are also shown in the table below . Mo del No. Electrical circuit required T otal connected load Gas type Manifold pressure Minimum gas supply[...]

16 Inst allation INST ALLING THE BURNER COMPONENTS Burner Components Remove the brass burner rings, porcelain burner caps, and porcelain grates from their shipping packages. Place each burner ring onto its corresponding burner base, being certain that the four alignment tabs slide into the matching notches in the base. Set each porcelain burner cap[...]

17 Inst allation MAKING THE ELECTRICAL CONNECTION Plug the three-prong plug from the appliance into the properly grounded and polarized wall receptacle. WARNING WARNING WARNING WARNING WARNING • Ensure that the power supply is disconnected before proceeding. • V erify that the power supply matches the ratings found on the appliance data plate b[...]

18 Operation VERIFYING THE OPERA TION Before beginning the test procedure, ensure that the gas supply is turned off at the shut-off valve, all cooktop control valves are in the “OFF” position, and all burner rings, burner caps, and grates are properly positioned on the cooktop. Rotate one knob at a time counterclockwise to the “LITE/HI” pos[...]

19 Operation T urn on the main gas supply to the cooktop by opening the gas shut-off valve. T est each burner separately by pressing and turning one control knob at a time counterclockwise to the “LITE/HI” position. All ignitors will spark simultaneously . (It will take approximately four seconds for ignition to occur , at which time all ignite[...]

1-877-4Electrolux www .electroluxusa.com www .electroluxca.com[...]