GE Monogram ZIC360N RH manual

Monogram. We bring good things to life. ® If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Installation Instr uctions ZIC360N RH, ZIC360N LH, ZICS360N RH, ZICS360N LH Built-In Bottom-Freezer Refrigerators Design Guide With Installation Instructions[...]

Safety Information Skill Level - Installation of this refrigerator requires basic mechanical, carpentr y and plumbing skills. Proper installation is the responsibility of the in- staller . Product failur e due to improper installation is not covered under the GE Appliance W ar ranty . See the Owner’s Manual for warranty infor mation. W ARNING: ?[...]

Design Guide THE INST ALLA TION SP ACE The finished cutout width must be 35-1/2". Water And Electrical Locations The opening must be prepared with the electrical and water supply located as shown. The cutout depth must be 24". Designed for industr y standard flush installation. The refrigerator will project for ward, slightly beyond adjac[...]

1/4" 1/2" 3/4" 1" 1-1/4" 1" 3/4" Overlay Panel (Nominal Size) 1/4" 1/2" 3/4" 2" 1-1/4" 1-1/2" 1-3/4" 3" 2-1/4" 2-1/2" 2-3/4" 1/4" 1/2" 3/4" Door 23-7/8" From Rear of Refrigerator 1" Refrigerator Case Trim Design Guide T op View 130 ° [...]

1/4" 1/2" 3/4" 1" 1-1/4" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Overlay Panel (Nominal Size) Case T rim Refrigerator Door Design Guide 5 T op View 90 ° DOOR SWING (optional setting) Scale 1:1[...]

Design Guide CUSTOMIZA TION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Overlay panels Y ou may also choose to install custom overlay panels from your cabinet manufacturer . This design provides a seamless appearance which integrates smoothly with sur rounding cabinetr y . Standard supplied handles shown in 3/4" overlay[...]

Design Guide 1/4" FRAMED P ANEL DIMENSIONS 7 If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door , drawer and grille. If the custom panel is less than 1/4" thick and if it fits loosely in the door frame, it can be backed up with a piece of filler material or fo[...]

Design Guide 8 SIDE P ANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Order the side panels from the cabinet manufacturer . ZUG2 GRILLE P ANEL DIMENSIONS The ZUG2 unified grille panel kit provides for the installation of a framed or overlay grille pa[...]

Installation Instructions 9 MA TERIALS REQUIRED • 35" long 2x4 for Anti-Tip support • Copper water line tubing • W ater shut-off valve (optional but recommended) • Custom panels for fresh food door , freezer drawer and grille panel • Screws to secure refrigerator to cabinetr y . FLOORING For proper installation, this refrigerator mus[...]

Installation Instructions NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber . STEP 1 REMOVE P ACKAGING CAUTION: Refrigerator is much heavier at the top than at the bottom – be careful when moving. When using a hand [...]

Installation Instructions 11 STEP 2A W A TER LINE INST ALLA TION WITH A REVERSE OSMOSIS SYSTEM Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis W ater System use the refrigerator’s filter bypass plug. Using the refrigerator’ s water filtration cartridge with the RO filter can result in[...]

12 Installation Instructions STEP 5 LEVEL REFRIGERA TOR All models have 4-point leveling. The front is sup- ported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator . • T o level the back of the refrigerator , turn the 7 /1 6" hex nut located above the front wheels. T ur n cl[...]

STEP 7 ADJUST DOOR SWING NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130 ° , you may change the door swing to a 90 ° opening. Skip this step if door opening is satisfactor y for your installation situation. • Lift the grille panel to access the wire cover trim. • Remove screws [...]

Installation Instructions 14 STEP 9 INST ALL FRAMED P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. • Follow the same procedures to install the drawer panel. Custom handles If you are [...]

Installation Instructions 15 STEP 9A INST ALL OVERLA Y P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the REAR screw holes. • Secure the handle to the door using the FRONT screw holes. • Follow the same procedures to install the drawer panel. Custom handles If you a[...]

16 Installation Instructions STEP 1 0 CONNECT W A TER SUPPL Y Check to be sure that refrigerator power cord is not plugged into the wall outlet. • Locate and bring copper tubing to the front of the cabinet. • T ur n the water on to flush debris from line. Run about a quart of water through tubing into a bucket, then shut-off water . • Slip a [...]

17 Notes[...]

18 Notes[...]

19 Notes[...]

Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram TM local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram. ® General[...]