Makita 1902 manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com P o wer Planer MODEL 1902 002543 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 change the plug in any wa y . Double insula- tion eliminates the need for the three wire grounded pow er cord and grounded power supply system. 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to [...]

4 model. Accessories that may be suitab le for one tool, may become hazardous when used on another tool. SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. F[...]

5 poor installation or a poorly balanced blade . 8. Make sure the blade is not contacting the workpiece bef ore the switch is turned on. 9. W ait until the blade attains full speed before cutting. 10. Keep at least 200 mm (8”) awa y from the tool at all times. 11 . Alwa ys switch off and wait for the blades to come to a complete stop before an y [...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting depth of cut Depth of cut ma y be adjusted by simply turning the knob on the front of the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s wit[...]

7 • Use only the Makita wrench provided to remo ve or install the blades . F ailure to do so may result in o ver tightening or insufficient tightening of the installation bolts. This could cause an injur y . 1. Remov e the existing b lade, if the tool has been in use, carefully clean the drum surfaces and the drum cov er . T o remov e the blades [...]

8 clearances between the b lade ends and the tool body . 9. Check the three he x flange head bolts for final tightness . 10. Repeat procedures 1 - 9 f or other blade. For the correct planer blade setting Y our planing surf ace will end up rough and unev en, unless the blade is set properly and securely . The b lade must be mounted so that the cutti[...]

9 The nozzle assembly ma y be attached after the chip cov er on the tool body is remov ed. When slipping on the assembly , fit the pin on it into the rear cov er hole. Use the chip cov er screws to f asten it in place. OPERA TION Planing operation First, rest the tool front base flat upon the workpiece surface without the blades making an y contact[...]

10 Dra w a cutting line on the wor kpiece . Inser t the edge fence into the hole in the front of the tool. Align the blade edge with the cutting line. Adjust the edge f ence until it comes in contact with the side of the workpiece, then secure it b y tightening the screw . When planing, mov e the tool with the edge fence flush with the side of the [...]

11 Chamfering T o make a chamfering cut as show n in the figure, align the “ V ” groov e in the front base with the edge of the workpiece and plane it. MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Replacing carbon brushes Remov e and check the carb[...]

12 Use a screwdriv er to remove the brush holder caps. T ake out the worn carbon br ushes , inser t the new ones and secure the brush holder caps. T o maintain product SAFETY and RELIABILITY , repairs, any other maintenance or adjustment should be perf or med by Makita A uthor iz ed or F actor y Ser vice Centers , always using Makita replacement pa[...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]