Makita 6911D manual

Cordless Impact Driver capamttes 1 High tensile bolt Machine screw Standard bolt 4 mm 8 mm 15/32" ~ 5/16") 5 mm 12 mm 13/16" 112"l 5 mm - 10 mm 13/16" ~ 318") Equipted with Electric Brake MODEL 6911D MODEL 6911DW With Fast Charger No load speed (RPMI 0 ~ 1,800 INSTRUCTION MANUAL Max fastening torque (See note 1 below1 [...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extens[...]

IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) 25 50 100 AWG Size of Cord 18 18 18 I. SAVE THESE INSTRUCTIONS - This manual 150 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified se[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5O0F1 or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the batte[...]

Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery cartridge with th[...]

Use only the driver bit or socket bit shown in the figure. Do not use any other driver bit or socket bit. To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. 11 mm (7/16") 9 mm (3/8") Sleeve To remove the bit, pull the sleeve [...]

Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing swi[...]

Operation The proper fastening torque may differ depending upon the kind or size of the screw, the type of material to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures below. Machine screw Kg .cm (ft . Ibs) 200 (15) al 3 P c p 100 ‘E (7) 4- VI U M8x 12 (5/16” x 1/2”) Proper fastening torque fo[...]

High tensile bolt Kg . cm (ft . Ibs) 800 (57) 600 m (43) P E! 400 ._ ? (29) 3 C (u c m 200 (15) Proper fastening for M8 (5/16') torque torque 0 1 2 3 Seconds Fastening time Hold the tool firmly and place the point of the driver bit in the screw head. Apply for- ward pressure to the tool to the extent that the bit will not slip off the screw an[...]

3. Bolt 0 Even though the torque coefficient and the class of bolt are the same, the proper .Even though the diameters of bolts are the same, the proper fastening torque will fastening torque will differ according to the diameter of the bolt. differ according to the torque coefficient, the class of bolt and the bolt length. 4. The type of materials[...]

MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 12[...]

ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits Size Part No. Phillips 78421 5-OA - Batter[...]

Am -14-'92 EN CORDLESS IMPACT DRIVER Model 6911D Note: The switch and other part configurations may differ from country to country. 14[...]

Apr-14- 92 EN MODEL 6911D 'itM $,, DESCRIPTION I:,'," AtD DESCRIPTION MACHINE ___ 1 2 3 4 S 6 7 8 9 10 11 12 13 14 15 16 17 1 6 1 1 1 1 1 1 1 1 1 1 1 4 1 1 2 - Name Plate Tapping Screw BT4x20 Pan Head Screw Max20 IWith Washer1 Houslnq Set IWith Item 291 set Plate Switch Lever Swltch LWW Ring Spring 12 Flat Washer 14 Compression Sprin[...]

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh[...]