Makita RBC25A manual

String Trimmer Model RBC221 RBC251 Models: RBC221 RBC251 RBC25A RBC25A INSTRUCTION MANUAL Dimensions (mm) Weight (kg) Gear ratio Clutch Drive Shaft Type Engine: (L x W x H) Revolution of cutter head (rpm) Displacement (cc) Power rating @s) Carburetor Starting system Ignition system Spark Plug Fuel tank (I) Fuel Read rules for operation and instruct[...]

Thank you very much for purchasing your MAKITA STRING TRIMMER. We are proud of and very confident in recommending our MAKITA STRING TRIMMER as a result of our extensive development and substantial knowledge and experience. Please read and understand this booklet thoroughly before operating your MAKITA STRING TRIMMER in order to take advantage of it[...]

23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. Use only replacement parts that are identical to original equipment parts when servicing the unit: these parts are available from your dealer. The use of any other accessory or attachment may create a potential hazard, injury to the user and damage to th[...]

EQUIPMENT DESCRIPTION 4[...]

ASSEMBLY INSTRUCTIONS Mounting the handle (Fig. 1) 1. Attach the handle to the drive shaft. 2. Install the handle joint on the handle as shown in Fig. 1. 3. Insert the installation bolt M6x45 through the holes in the handle, and attach the flange nut M6. 4. Adjust the handle to the desired position and tighten the installation bolt. Mounting the pr[...]

PREPARING FOR OPERATION Fuel and oil mixture Inspect the fuel tank and fill with clean, fresh fuel of the proper mixture to assure the longer life of the tool. Use the following mixed gas. Gasoline : Genuine Makita Two-cycle engine oil = 50 : 1 or Gasoline : Other manufacturer's Two-cycle engine oil = 25 : 1 recommended FOR CALIFORNIA REGULATI[...]

ENGINE STARTING AND STOPPING PROCEDURES Starting when the engine is cold Use the following procedure when the engine is cold, or after it has been stopped for longer than 5 minutes, or after fuel has been added to the engine: 1. Slide the stop switch away from the "STOP" position (Fig. 5). 2. Gently push on the primer pump repeatedly (7 -[...]

CORRECT HANDLING OF THE MACHINE . Fig. 9 Fig. 10 I I Attachment, adjustment and detachment of the shoulder strap Attachment Place the strap hook into the hanger which is located on the shaft between the grip and the handle. Adjustment Adjust the strap length so that the nylon cutting head will be kept parallel to the ground (Fig. 9). Detachment (NO[...]

DAILY CHECK-UP AND MAINTENANCE cover r cleaner case cleaner cover I Sponge element Fig. 12 Fig. 13 0.6 mm - 0.7 mm (0.024" - 0.028") 1. 2. 3. 4. 5. 6. 7. a. 9. 10. 11. Fig. 14 I Fig. 15 Before operation, pay particular attention to the tightness of the nylon cutting head. Re-tighten the nylon cutting head if necessary (every 8 hours or da[...]

STORAGE When storing the machine for a long time, drain the fuel from the fuel tank and carburetor as foll,ows: 1. Drain all fuel from the fuel tank. Gently push on the primer pump repeatedly until all fuel is expelled out of the primer pump. Properly dispose of the fuel in accordance with all local laws. 2. Remove the spark plug and add a few drop[...]

INSTRUCTIONS FOR USE OF THE NYLON CUTTING HEAD (BUMP & FEED BF4) Safety Instructions 1. Read this section carefully and thoroughly before use. 2. Check the nylon cutting head carefully before each use. If you notice any of following, replace the worn or damaged parts with new ones immediately (Fig. 19): Dents appear on the knob head. The housin[...]

Replacing the nylon cord 1. 2. 3. 4. 5. 6. 7. Press the housing latches inward to lift off the cover; then remove the spool (Fig. 23). Run the new nylon cord through the hole in the center of the spool, and pass one end of the cord through the notch into the other side of the spool. Allow one end of the cord to extend about 3" (80 mm) further [...]

Emission Control Warranty Statement YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board and Makita U.S.A., Inc. are pleased to explain the emission control warranty on your 1995 and later utility and/or lawn and garden equipment engine. In California, new utility and lawn and garden equipment engines must be designed, built and [...]

LIMITED WARRANTY - California Only - Makita U.S.A., Inc., a distributor of utility and lawn and garden equipment in the U.S., warrants to the owner of 1995 and later utility and/or lawn and ga'rden equipment engines that the engine (1) has been designed, built, and equipped at the time of manufacture so as to conform with the applicable regula[...]

WHAT IS NOT COVERED UNDER THIS WARRANTY This warranty does not cover any emission-related part which malfunctions, fails, or is damaged due to alter- ations and/or modifications such as changing, adding, or removing parts. When an engine is being serviced under warranty, Makita U.S.A., Inc. and any of its authorized dealers, distribu- tors, or warr[...]

REPAIR AND REPLACEMENT OF EMISSION-RELATED PARTS It is recommended that only engine replacement parts which have been authorized and approved by Makita U.S.A., Inc. should be used in the performance of any warranty maintenance or repairs of emission-related parts. These replacement parts will be provided at no charge if the part is still under warr[...]