Moxa Technologies G2150I manual

G2150I A T Command Set Second Edition, June 2007 www .moxa.com/product Moxa Technologies Co., Ltd. Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Web: www.moxa.com MOXA Technical Support World wide: support@ moxa.com The Americas support@ usa.moxa.com[...]

OnCell G2150I AT Command Set The software d escribed in t his manual is furnished u nder a license a greement and m ay be used only in accordance with the term s of that agreement. Copyright Notice Copyright © 2007 Moxa Technologies Co., Ltd. All rights reserved. Reproducti o n without perm ission is prohibited. Trademarks MOXA is a re gistered tr[...]

Table of Contents Chapter 1 Introduction .................................................................................................. 1-1 Scope of the Document .......................................................................................................... .. 1-2 Related Do cuments ...................................................[...]

Chapter 5 Network Service Commands ....................................................................... 5-1 Signal Qua lity: +C SQ .............................................................................................................. 5-2 Operator Selec tion: +COPS ..........................................................................[...]

Select Data Error Correcting Mode: N ................................................................................... 8-7 Chapter 9 V24-V25 Commands ..................................................................................... 9-1 Fixed DTE Ra te: +IPR ....................................................................................[...]

Failure Cause from GSM 04 .08 Recomm enda tion: +CEER................................................... A-4 Specific Failure Cause for +CEER ......................................................................................... A-6 GSM 04.1 1 Annex E-2: Mobile Originating SM-T ransfer...................................................... A-6 Un[...]

1 1 Chapter 1 Introduction This chapter is an introductio n to the OnCell G 2150I AT Command Set. The follow ing topics are covered:  Scope of the Document  Related Documents  ETSI Secretariat  Abbreviations  Definitions  Presentation Rules[...]

OnCell G2150I AT Command Set Introduction 1-2 Scope of the Document This docum ent describes the AT-comm and based messages exchange d between an a pplication a nd the OnCell G2150I for managing GSM related events or services. Related Documents The interface s pecifications d escribed here are based on t he following recomm endations: [1] ETSI GSM [...]

OnCell G2150I AT Command Set Introduction 1-3 Abbreviations ADN Abbreviate d Dialing N umber (P honebook) AMR Adaptive Multi-Rate AMR-FR AMR Full Rate (full rate speech Version3) AMR-HR AMR Half Rate (half rate speech version 3) AOC Advice Of Charge ASCII Standard characters table (1 byte coding) AT Modem Hayes comm ands prefix (for “ATt en t i o[...]

OnCell G2150I AT Command Set Introduction 1-4 Definitions The words “Mobile Station” (MS) or “Mobile Equipment” (ME) are used for mobile terminals that support GSM services. Term inal Equipment (TE) is the Human Machine Interface (HMI) of a GSM device ( modem or handset). TE can be a handset HMI or the AT c ommand li ne interface. A call fr[...]

2 2 Chapter 2 AT Command Features This chapter inclu des information about the AT Comman d Features of the OnCell G2150I . The following topics are covered in this chap ter:  Serial Line Settings  Command Line  Information Response and Result Codes[...]

OnCell G2150I AT Command Set AT Command Features 2-2 Serial Line Settings A serial li nk handle r is config ured with t he following default values (factory settings): y 115200 bps y 8 data bits y 1 stop bit y no parit y y RTS/CTS flow control Use the +IPR, +IFC, and + ICF commands to change t hese settings. Command Line Commands alway s start with[...]

3 3 Chapter 3 General Commands This chapter includ es in formation about the General Comman ds of the OnCell G2150I. The following topics are covered in this chap ter:  Manufacturer Identification: +CG MI  Request Mode l Identification: + CGMM  Request Re vision Identi fication: +C GMR  Product Serial Number: + CGSN  Select TE Charac[...]

OnCell G2150I AT Command Set General Commands 3-2 Manufacturer Identification: +CGMI Description: This c ommand give s the m anufacturer ide ntification. Command syntax: AT+CGMI Command Possible Responses AT + C G M I Note: Get manufacturer identification W A VECOM MODEM OK Note: Command valid, W avecom modem Defined values: No param eters Request [...]

OnCell G2150I AT Command Set General Commands 3-3 Request Revision Identification: +CGMR Description: This comm and is used t o get the revised softw are version. T his functio n only appl ies to default IP addresses. Command syntax: AT+CGMR Command Possible responses AT + C G M R Note: Get softwar e version 657_09gg.02406 B 2015268 100506 17:01 OK[...]

OnCell G2150I AT Command Set General Commands 3-4 Phonebook Character Set: +WPCS Description: This specific command in forms the ME which character set is used by the TE for the phonebooks. The ME can convert each char acter of en tered or displayed st rings. This is used t o read or write phonebook en tries (parameters <text>, <address>[...]

OnCell G2150I AT Command Set General Commands 3-5 A T+CCID= ? Note: Get possible value OK Note: No parameter but this command is valid Note: if there is no EF-CCID file present on th e SIM, the +CCID answer will no t be sent, but the OK message will be returned. Defined values: No param eter Capabilities List: +GCAP Description: This command gets t[...]

OnCell G2150I AT Command Set General Commands 3-6 AT+CPO F). This co mmand ex ecutes an I MSI DETA CH an d makes a backup cop y of some internal parameters in SIM a nd in EEPROM. The SIM card cannot then be accessed. If the m obile equipment is not powere d off by t he applicati on after thi s command has been sent, a re-sta rt command (AT+CFUN=1) [...]

OnCell G2150I AT Command Set General Commands 3-7 Report Mobile Equipment Errors: +CMEE Description: This comma nd disables or ena bles the use of the “+CME ERROR: <xxx>“ or “+CMS ERROR:<xxx>“ result code instead of simply “ERROR”. Command syntax: Command syntax: AT+ CMEE=<error reporting flag> Command Possible respons[...]

OnCell G2150I AT Command Set General Commands 3-8 A T+CCLK? Note: Get curr ent date and time +CCLK: “00 /06/09, 17:34:23” OK Note: current date is June 9 th , 2000 current time is 5:34:23 pm Defined values: <date and time string> String format for date/time is: “yy/MM/dd, hh :mm:ss”. Valid years are 00 (for 2000) to 99 (for 2099). Th [...]

OnCell G2150I AT Command Set General Commands 3-9 Command Possible responses A T+CSIM= <l ength>,<command> +CSIM : <length>,<resp onse> +CME ERROR : <err> AT + C S I M ? O K A T+CSIM= ? OK Defined values: <length>: integer ty pe Length of the characters that are sent to TE i n <command> or <response> [...]

OnCell G2150I AT Command Set General Commands 3-10 “9408”. By using the A T+CSIM comm and, the “READ RE CORD” and “SEEK” actions retu rn 4,”9408” instead of CME ERROR:13. Restricted SIM Access: +CRSM Description: By using this command instead of Gene ric SIM Access the +CSIM TE application gives easier but more limited access to the[...]

OnCell G2150I AT Command Set General Commands 3-11 to GSM 11.11 or 3GPP TS 51.011). After th e READ BINARY or READ RECORD command, the requested data will be returned. <error>: intege r type 3: Wrong format or pa rameters of the comm and 13: SIM no r esponse Mobile Equipment Control Mode: +CMEC Description: This command selects th e equipment[...]

OnCell G2150I AT Command Set General Commands 3-12 AT + C I N D ? Note: r ead ME indicators current values +CIND: <ind>[, <ind>[,…]] OK A T+CIN D? +CIND: 2,2,1,0, 0,0,0 A T+ CIND= ? Note: r ead ME indicators possib le values +CIND: (<descr>,(list of supported<in d>s))[,(<des cr>,(list of supprted <ind>s))[ ,…[...]

OnCell G2150I AT Command Set General Commands 3-13 command is ignored and th e mode m will re turn a +CME ERROR: <err> respo n se. Restrictions • Only b asic option and UI H framing is su pported. • Only conver gence layers type 1 and 3 ar e supported. • Autobauding is not compliant with multiplexing mode. It is neither possible to star[...]

OnCell G2150I AT Command Set General Commands 3-14 Command Possible responses A T+CMUX= ? Note: Get possible values MUX: (0),(0),(1 -5),(1-255) ,(1-128),(0 -255),(1-12 8),(1-128) OK AT + C M U X ? Note: Get current values +CMUX:<mode>,<subset>,<po rt_s peed>,<N1>,<T 1>,<N2 >,<T2>,<T3> OK or +CME ERROR[...]

4 4 Chapter 4 Call Control Commands This chapter includ e s in formation about the Call Con trol Commands of the OnCell G2 150I. The following topics are covered in this chapter:  Dial Command: D  Hang-Up Comma nd: H  Answer a Call: A  Remote Disconnecti on  Extended Error Report: +CEER  DTMF Signals: + VTD, +VTS  Redial Last T[...]

OnCell G2150I AT Command Set Call Control Commands 4-2 Dial Command: D Description: The ATD command is used to set a voice, data or fax call. As per GSM 02.30, t he dial command also controls supplem entary services. For a data or a fax call, the application sends th e following ASCII string to the product (the bearer m ust be previousl y selected [...]

OnCell G2150I AT Command Set Call Control Commands 4-3 Command Possible responses AT + C P B S ? Note: Which phonebook is selected ? +CPBS:”SM”,8,10 Note: ADN phone book is sel ected, 8 loc ations ar e used and 10 locati on s ar e availabl e AT D > S M 6 ; Note: Call index 6 fr om ADN phonebook OK Note: Call succeeds When the FD N phone book[...]

OnCell G2150I AT Command Set Call Control Commands 4-4 Command Possible responses AT H Note: Ask for disconnection OK Note: Every call, if any , ar e r eleased AT H 1 Note: Ask for outgoing call disconnection OK Note: Outgoing call, if any , is released Defined values: <n> 0: Ask for disconnecti on (defaul t value) 1: Ask for outgoing call di[...]

OnCell G2150I AT Command Set Call Control Commands 4-5 DTMF Signals: +VTD, +VTS +VTD descriptio n: The product ena bles the use r applicati on to send DTM F tones over the GSM network. Thi s comm and is used t o define t one duratio n (the de fault value i s 70 ms ± 5 ms, according to 3GPP 23.014). Command syntax: AT+VTD=<n> Command Possible[...]

OnCell G2150I AT Command Set Call Control Commands 4-6 Automatic Dialing with DTR: AT%Dn Description: This comm and enables and disables: • automatic dialing of the phone number stored in the first location of the ADN phonebook (or FDN phoneboo k, if it is activated using +CLCK command ). • automatic sending of the short message (SMS) stored in[...]

OnCell G2150I AT Command Set Call Control Commands 4-7 activated using +CLCK command). Voice call (with semi-colon). AT%D1 Activates automatic DTR dialing if DTR switches from OFF to ON; Dials the phone num ber in the first location of the AD N phonebook (or FDN ph onebook, i f it is activated using +CLCK command). Data or Fax call (withou t semi-c[...]

OnCell G2150I AT Command Set Call Control Commands 4-8 Single Numbering Scheme: +CSNS Description: This command selects the bearer to be used when an MT single num bering scheme call is set up (see +CICB). Note: Setting the +CSNS command affect s the curren t value of +CICB. Command syntax: AT+CSNS Command Possible responses A T+CSNS=2 Note: for ce[...]

OnCell G2150I AT Command Set Call Control Commands 4-9 Defined values: <Rgain>: reception g a in <Tgain>: transm ission gain AT + V G R = < v a l > for receive gain AT + V G T = < v a l > Controller 1 for transmit gain Controller 1 AT + V G T = < v a l > Controller 2 for transmit gain Controller 2 0 to 15 +6 db 0 to 31[...]

5 5 Chapter 5 Network Service Commands This chapter includ es in formation about the Network Service Co mmands of the OnCell G2150I. The following topics are covered in this chapter:  Signal Qu ality: + CSQ  Operator Selection: +COPS  Network Registra tio n: + C R EG  Operator List Management: +WOLM  Read Operator Name: +WOPN  Sel[...]

OnCell G2150I AT Command Set Network Service Commands 5-2 Signal Quality: +CSQ Description: This command is used t o ascertain the r eceive d signal strengt h indication (<rssi>) and the chann el bit error rate (<ber>) with or with out a SIM card inserted. Command syntax: AT+CSQ Command Possible responses A T+CSQ +CSQ: <rssi>,<[...]

OnCell G2150I AT Command Set Network Service Commands 5-3 +CME ERROR: 547 Emergency call is allowed without SIM Careful: Error co d e + CME ERROR: 546 or +CME ERROR: 547 are only return ed if SIM is not present. The fact that network supports emergency calls ( + CME ERRO R: 547) does not imply that emergency calls will work without a SIM. Th e on l[...]

OnCell G2150I AT Command Set Network Service Commands 5-4 AT + C O P S = 2 Note: Ask for der egistra tion fr om ne twor k OK Note: Succeeded AT + C O P S ? Note: Ask for cur rent PLMN +COPS: 2 Note: ME is unr egister ed until <mode>=0 or 1 is selected Defined values: <mode> 0: automatic (default value) 1: manual 2: deregistration; ME wi[...]

OnCell G2150I AT Command Set Network Service Commands 5-5 0: Disable network registration un solicited result code (default) 1: Enable network re gistration code result code +C REG: <stat > 2: Enable netwo rk registrat ion and locat ion info rmation unsol icited res ult code +CREG: <stat>,<lac>,<ci> if there is a change of n[...]

OnCell G2150I AT Command Set Network Service Commands 5-6 AT + W O L M = 0 , 1 1 Note: Delete an entry at location 1 1 +CME ERROR: 21 Note: Invalid index Defined values: <mode> : 0 delete 1 write 2 read <loc> : location. If this parameter is not filled with <mode>=1, the location will be the first empty one. <NumOper>: Oper [...]

OnCell G2150I AT Command Set Network Service Commands 5-7 A T+WOPN=0,999 99 Note: Give a wr ong operator +CME ERROR: 22 Note: Not found A T+W OPN=0,20801,36 Note: Give an operator in numeric format for lac 36 +WOPN : 0,”Orang e F” OK Note: Alphanumeric answer A T+WOPN=3,0 Note: Erase N ITZ PLMN na mes stor ed in flash memory OK A T+WOPN=4 Note:[...]

OnCell G2150I AT Command Set Network Service Commands 5-8 Selection of Preferred PLMN List: +CPLS Description: This command is used to select one PLMN selector with acce ss technology list in the SIM card that is used by AT+CPOL command. Command syntax: AT+CPLS= <List> Command Possible responses AT + C P L S ? Note: Ask for selection of the S[...]

OnCell G2150I AT Command Set Network Service Commands 5-9 A T+CPLS=? Note: Get possible values +CPLS: (0,1,2) OK Note: The 3 files with Acces technology ar e pr esent and can be selected A T+CPLS=? Note: Get possible values +CPLS: (0) OK Note: Only EF_PLMNwAct or EF_PLMNsel can be selected Defined values: <List>: 0: User controlled PLMN selec[...]

OnCell G2150I AT Command Set Network Service Commands 5-10 AT + C P O L = , 0 Note: Select long alphanumeric format OK AT + C P O L ? Note: Ask for pr eferred list of networks with only EF_PLMNsel pr esent +CPOL: 1,0,”D1-TELEKOM” +CPOL: 6,0,”F SFR” OK Note: Pr eferr ed list o f networks in long alphanumeric fo rm at A T+CPOL=7,2,20801 Note:[...]

OnCell G2150I AT Command Set Network Service Commands 5-11 to get the maxim um index of the selected EF. <format>: 0 long alphanumeric form at for <oper> 1 short alphanum eric form at for <ope r> 2 numeric format for < oper> <oper>: character string or integer (see <format>) in d icating operator identifier. <[...]

6 6 Chapter 6 Security Commands This chapter includ e s in formation about the Security Comman ds of the OnCell G2150I. The following topics are covered in this chapter:  Enter PIN: +CPIN  Enter PIN2: +CPIN2  PIN Remaining Attemp t Nu mber: +CPINC  Facility Lock: +CLCK  Change P assword: +CPW D[...]

OnCell G2150I AT Command Set Security Commands 6-2 Enter PIN: +CPIN Description: This command is u s ed to enter the ME passwords (CHV1 / CHV2 / PUK1 / PUK2, etc.), that are required before any ME functionality can be used. CHV1/CHV2 is between 4 an d 8 digits long, PUK1/PUK2 is only 8 digits long. If the user appl ication tries to make an outgoing[...]

OnCell G2150I AT Command Set Security Commands 6-3 AT + C P I N ? +CPIN: SIM PIN A T+CPIN =1235 +CME ERROR: 16 A T+CPIN =1236 +CME ERROR: 16 A T+CPIN =1237 +CME ERROR: 16 AT + C P I N ? +CPIN: SIM PUK A T+CPIN =99999999,5678 OK AT + C P I N ? +CPIN: READY Read the PIN status The pr oduct r equir e s SIM PIN First attempt to enter a SIM PIN W r ong [...]

OnCell G2150I AT Command Set Security Commands 6-4 A T+CPIN2=5678 Note: Enter PIN2 +CME ERROR: 3 Note: Operation n ot allowed, PIN2 previously enter e d After 3 unsuccessful attempts, PUK2 will then be requ ired. PUK2 va lidatio n forces th e user to enter a new PIN2 code as a second parameter and this will be the new PIN2 code if PUK1 validation s[...]

OnCell G2150I AT Command Set Security Commands 6-5 Facility Lock: +CLCK Description: This command is u s ed by the application to lock, unlock , or interrogate an ME or network facility <fac>. Note: Test SI M cards (with MCC=001 & MNC=01) do not check “PS” , “PN”, “PU” , “PP” and “PC” locks. Command syntax: AT+CLCK=<[...]

OnCell G2150I AT Command Set Security Commands 6-6 • “AC”: All inComing barring services • “PN”: Network lock with an 8-digit passwo rd (NCK). • “PU”: Network Subset lock with an 8-digit password (NSCK). • “PP”: Service Provider lock with an 8-digit password (SPCK). • “PC”: Corporate lock with an 8-d ig it password (CC[...]

OnCell G2150I AT Command Set Security Commands 6-7 Change Password: +CPWD Description: This comm and is used by the a pplication to c hange a passw ord (PIN, call barring, NCK, etc.). The facility values (<fac>) are th e same as for the +CLCK command with a “P2” facility to manage SIM PIN2. For the network lock (“PN”), unlocking is fo[...]

7 7 Chapter 7 Short Message Commands This chapter includ es in formation about the Shor t Messag e Commands of the OnCell G2150I. The following topics are covered in this chapter:  Parameter Definitions  Select Message Service: + CSMS  New Message Acknowledgement: + CNMA  Preferred Message Storage: +CPMS  Preferred Message Form at: +[...]

OnCell G2150I AT Command Set Short Message Commands 7-2 Parameter Definitions <da> Destination Address, coded lik e GSM 03.40 TP-DA <dcs> Data Codin g Schem e, coded like i n document [5]. <dt> Discharge T ime in string format: “yy/MM/ dd,hh:mm:ss zz 　 ”(Y ear [00-99], M onth [0 1-12], Day [01-31], Hour , Minute, Sec ond and[...]

OnCell G2150I AT Command Set Short Message Commands 7-3 Select Message Service: +CSMS Description: The supported services are originated (SMS-MO) and terminated short message (SMS-MT) + Cell Broadcast Message (SM S-CB) services. Command syntax: AT+CSMS=<service> Command Possible responses A T+CSMS=0 Note: SMS A T com m an d Phas e 2 version 4[...]

OnCell G2150I AT Command Set Short Message Commands 7-4 A T+CNMI=2,2,0, 0,0 Note: <mt>=2 OK +CMT : “123456” ,”98/10/01, 12:30 00+ 00”, 129, 4, 32, 240, “15379”, 129, 5 <CR><LF> Received message Note: message r eceived Example of acknowledgem ent of a new message in PDU mode: Command Possible responses A T+CSMS=1 Note: [...]

OnCell G2150I AT Command Set Short Message Commands 7-5 Preferred Message Storage: +CPMS Description: This command allo ws the message storage area to be selected (for reading, writing, etc). Command syntax: AT+CPMS=<mem1>,[<mem2>,[<mem3>]] Command Possible responses A T+CPMS=? Note: Possible mess age storages +CPMS: ((“SM”,?[...]

OnCell G2150I AT Command Set Short Message Commands 7-6 AT + C P M S ? Note: Read +CPMS: “SM”,4,10 , ”ME”,4,99,”ME”,4,99 OK Note: Read SMS fr om SIM; w rite, stor e SMS fr o m/to flash Defined values: <mem1> Memory used to list, read , and delete messages. It can be: • SM: SMS message storage in S IM (default) • ME: SMS messag[...]

OnCell G2150I AT Command Set Short Message Commands 7-7 Defined values: <mode> PD U or text m ode 0 PDU mode 1 T ext mode The <pdu> m e ssage is com posed of the SC a ddress (00 m eans no SC a ddress given, use default SC address rea d with +CSCA command) an d the TPDU m essage. In this exam ple, the length in bytes of the TPD U buffer [...]

OnCell G2150I AT Command Set Short Message Commands 7-8 Command Possible responses AT + C S D H = 0 Note: Set val ue to “d o not show ” OK AT + C S D H ? Note: Curr ent value +CSDH: 0 OK Note: Do not show header values Defined values: <n>: show indicator • 0: do not show head er values • 1: show the values in result codes New Message [...]

OnCell G2150I AT Command Set Short Message Commands 7-9 1: SMS-DELIVERs are routed usi ng unsoli cited code: +C MTI: “SM”,<i ndex> 2: SMS-DELIVERs (e xcept class 2 m essages) are routed using unsoli cited code: if PDU mode: +CMT: [<alpha>], <lengt h> <CR> <LF> < pdu> if text mode: +CMT: <oa>,[<alpha&[...]

OnCell G2150I AT Command Set Short Message Commands 7-10 Command Possible responses A T+CMTI: “SM”,1 Note: New message r eceived AT + C M G R = 1 Note: Read the message +CMGR: “REC UNREAD”, “0146290800 ”, “98/10/01 ,18:22:1 1+00”, <CR ><LF> ABCdefGHI OK AT + C M G R = 1 Note: Read the message agai n +CMGR: “REC READ ?[...]

OnCell G2150I AT Command Set Short Message Commands 7-11 Command Possible responses A T+CMGL=“REC UNREAD” Note: List u nr ead messages in text mo de +CMGL: 1,”REC UNREAD”,”01462908 00”,, <CR><LF> I will be late +CMGL: 3,”REC UNREAD”, “46290800 ”,, <CR><LF>See you tonight ! OK Note: 2 messages ar e unr ead[...]

OnCell G2150I AT Command Set Short Message Commands 7-12 +CMGS: <mr>,, OK Note: Successful transmission A T+CMGS=<length><CR> Note: Send a message in P DU mode ( 1/3) <pdu> Note: Enter message in PDU mode (2/3) <ctrl-Z> Note: End the message (3/3) +CMGS: <mr> OK Note: Successful transmission The message refere nc[...]

OnCell G2150I AT Command Set Short Message Commands 7-13 mode (default “STO UNSE NT” for +C MGW). Indicates the status of message in memory. If <stat> is omitted, the stored message is considered as a message to send . 0 “REC UNREAD ” 1 “REC READ” 2 “STO UNSENT” 3 “STO SENT” <length> Length of t he actual data u nit [...]

OnCell G2150I AT Command Set Short Message Commands 7-14 but can be use d in PDU m ode (+CMGS). SRR: Status Report Requ est, b5=1 if a status report is requested. This mode is supported . VPF: Validity Period Format b4=0 & b3=0 -> <vp> fiel d is not present b4=1 & b3=0 -> <vp> fi eld is present in relative form at Other fo[...]

OnCell G2150I AT Command Set Short Message Commands 7-15 A T+CMGD=1,0 OK Note: The message fr om the pr eferr ed message storage at the location 1 is deleted A T+CMGD=1,1 OK Note: All READ mess ages fr om the pr eferr ed message storage a r e deleted A T+CMGD=1,2 OK Note: Al l REA D mess age s and SENT mobile ori gin at ed me ssages ar e deleted A [...]

OnCell G2150I AT Command Set Short Message Commands 7-16 Select Cell Broadcast Message Types: +CSCB Description: Th is command selects which types of CBM s are to be rece ived by the ME. It is allowed in both PDU and text mode s. Command syntax: AT+CSCB=<mode>, [ <mids>, [ <dcss> ] ] Important note: Test rea d comm and (AT+CSCB ?)[...]

OnCell G2150I AT Command Set Short Message Commands 7-17 A T+W CBM=“10,100,1000 ,10000” Note: W r ite 4 message identifiers in EF- CBMI OK Note: CBMIs ar e stored in EF-CBMI A T +WCBM? Note: Read the CBMIs in EF-CBMI +W CBM=“10 ,100,1000,10 0000” OK Note: 4 CBMIs ar e stor ed in EF-CBMI Message Status Modification: +WMSC Description: These [...]

OnCell G2150I AT Command Set Short Message Commands 7-18 Command Possible responses AT + C P M S ? Note: Check the storage ar ea +CPMS: “SM”,3,10,”SM”,3,10,”SM” ,3,10 OK A T+CMGW =“+3314629080 0”<CR> Hello how are you ?<ct rl -Z> Note: W rite a message in text mode +CMGW : 4 OK Note: Message stor ed in index 4 in the SIM[...]

OnCell G2150I AT Command Set Short Message Commands 7-19 A T+CMGR=10 +CMGR: “REC UNREAD”,”+3366 0669023”,,”03/02/13,18 :36:35+00”<CR><LF> Do you want to change state ? OK Note: The state has n’t be updated A T+WUSS=0 OK +CMTI: “SM”,1 1 Note: SMS has been r eceived in index 1 1 A T+CMGR=11 +CMGR: “REC UNREAD”,”+33[...]

OnCell G2150I AT Command Set Short Message Commands 7-20 AT + C M G R = 1 Note: Read the first SMS from the SIM +CMGR: “REC UNREAD”,”0146 290 800”, “98/10/01 ,18:22:1 1+00”, <CR ><LF> My test message: SMS in the SIM at location 1 OK AT + W M C P = 0 , 1 Note: Copy the SM S at locat ion 1 in t he SIM to the Fl ash OK AT + C P[...]

OnCell G2150I AT Command Set Short Message Commands 7-21 AT + W M C P = 0 Note: Copy all the SMS fr om the SIM to the Flash OK AT + C P M S ? Note: Rea d the SMS st orage +CPMS: “ME”,4,99,”ME”,4 ,99,”SM”,4,10 OK Note: 4 SMS ar e stored in the flash. Defined values: <mode> Copy mode • 0: From the SIM to the Flash • 1: From the [...]

8 8 Chapter 8 Data Commands This chapter includ es in formation about the Data Commands of th e OnCell G2150I. The following topics are covered in this chapter:  Using AT Commands Duri ng a Data Connection  Bearer Type Selection: +CBST  Select Mode: +FCLASS  Service Reporting Control: +CR  Cellular Result Codes: +CRC  DTE-DCE Loca[...]

OnCell G2150I AT Command Set Data Commands 8-2 Using AT Commands During a Data Connection To use AT Commands during a data conn ectio n (e.g., while the product is in online mode), it is necessary either to switch to offline mode, or to use the specific +WMUX command to enable Commands / Data multiplexin g. Switch from online to offline mode: To sw[...]

OnCell G2150I AT Command Set Data Commands 8-3 6 4800 bp s (modem type: V.32 ) 7 9600 bp s (modem type: V.32 ) 8 Specific 12 9600 b ps (m odem ty pe: V.34) 14(*) 1400 bps (modem ty pe: V.34) 6 5 30 0 b ps (m odem type: V.110) 66 1200 bps (mode m type: V.110) 68 2400 bps (mode m type: V.110) 70 4800 bps (mode m type: V.110) 71 9600 bps (mode m type:[...]

OnCell G2150I AT Command Set Data Commands 8-4 +CR: ASYNC For asynchronous tr ansparent +CR: REL ASYNC For asynch ronous non-transparent Command syntax: AT+CR=<mode> Command Possible responses A T+CR=0 Note: Extende d r eports disabled OK Note: Command valid A T+CR=1 Note: Extende d r eports enabled OK Note: Command valid A T+CR? +CR: 1 OK A [...]

OnCell G2150I AT Command Set Data Commands 8-5 Command syntax: AT+ILRR = <value> Command Possible responses A T+ILRR=0 Note: Local port rate report disabled OK Note: Command valid A T+ILRR=1 Note: Local port rate report enabled OK Note: Command valid A T+ILRR? +ILRR: 1 OK A T+ILRR=? +ILRR: (0,1) OK Defined values: <value>: 0: disable lo[...]

OnCell G2150I AT Command Set Data Commands 8-6 Select Data Compression: %C Description: This command enables or disables dat a compression negotiati on if this feature is supported by the pr o duct . Command syntax: AT%C<n> Command Possible responses AT % C 0 Note: Comma nd OK Note: Featu r e supported AT % C 2 Note: Comma nd OK Note: V42bis [...]

OnCell G2150I AT Command Set Data Commands 8-7 V42 bis Data Compression Report: +DR Description: Th is command determines whether or not the use of V42bis is allowed for an incoming or outgoing data call, if the feature is provided by the produ ct. The intermediate result code repres ents current DCE-DCE dat a compressio n type. The format of t his[...]

9 9 Chapter 9 V24-V25 Commands This chapter includ e s in formation about the V24-V25 Co mmands of the OnCell G2150I. The following topics are covered in this chapter:  Fixed DTE Rate: +IPR  DTE-DCE Charac ter Framing: +I CF  DTE-DCE Local Flow Control: +IFCR  Set DCD Signal: &C  Set DTR Signal: &D  Set DSR Signal: &S [...]

OnCell G2150I AT Command Set V24-V25 Commands 9-2 Fixed DTE Rate: +IPR Description: This command specifies the data rate at which the DCE wi ll accept commands. Notes: y The serial autobauding feature is supported, and covers the follow ing serial speeds (only): 2400, 4800, 9600, 19200, 3840 0, 57600 bps. Beyond those serial speeds, prope r operati[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-3 DTE-DCE Character Framing: +ICF Description: Th is command is used to determine the local serial port start-stop (asynchronous) character framing used by the DCE. Command syntax: AT+ICF= <format>[, <parity>] Command Possible responses A T+ICF? +ICF: 3,4 OK Note: Curr ent values A T+I CF=[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-4 A T+IFC=0,0 OK Note: New values Defined values: < DCE_by_D TE > 0: none (supported ) 1: XOn/X off local circ uit 103 ( not suppo rted) 2: RTS (supported) 3: Xon/Xoff global o n circ uit 103 (not supporte d) Important note: Wh en this parameter is set to 2 (DTE invokes flow contro l th rough RT[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-5 AT & D 1 Note: Modem switches from data to command mode when DTR switch es fr om ON to OFF OK Note: Command valid AT & D 2 Note: When DTR switches fr om ON to OFF , the call is r eleased OK Note: Command valid Defined values: <n> 0: The DTR si gnal is igno red 1: Modem switches from da[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-6 Defined values: <n> 0: DCE tra nsmission resul t code 1: Result c odes are su ppressed and not transm itted DCE Response Format: V Description: This command determ ines whether or not the DCE respons e format uses the header characters <CR><LF>, and t he result code s are provide d[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-7 Auto-tests: &T Description: This command allows t he triggering of vari ous auto-tests. Command syntax: AT&T<n> Command Possible responses AT & T 0 Note: Perform softwar e auto-tests OK Note: No softwar e pr oblem detected, all checksums ar e corr ect AT & T 1 Note: Do the audi[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-8 Restore Factory Settings: &F Description: This command is use d to restore t he factory setti ngs from EEPR OM. It onl y restores the para meters th at can be found in pa ragraph 19 Codes and val ues (Parameters Stora ge paragraph) wit h AT&F column checked. Those pa rameters are restore d i[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-9 Request Identification: I Description: This command causes t he product to t ransmit one or more li nes of specific information text Command syntax: A T I < n > Command Possible responses AT I 0 Note: Ma nufactur er and m odel identification s W A VECOM MODEM 900P OK Note: GSM 900 MHz pri mary[...]

OnCell G2150I AT Command Set V24-V25 Commands 9-10 Data / Commands Multiplexing: +WMUX Description: Th is specific command allows managing the data / AT comman ds multiplexing Command syntax: AT+WMUX=<mode > Command Possible responses A T+WMUX=? + WMUX: (0-1) OK A T +WMUX? +WMUX : 0 OK Note: Data / Commands multiplexin g d isabled. A T+WMUX=1[...]

1 1 0 0 Chapter 10 GPRS Commands This chapter includ es in formation about the GPRS Commands of the OnCell G2150I. The following topics are covered in this chapter:  Define PDP C ontext: + CGDCONT  Quality of Service Profil e (Requested): + CGQREQ  Quality of Service Profil e (M inimum acceptable): +CGQMIN  GPRS Attach or Detach : + C G[...]

OnCell G2150I AT Command Set GPRS Commands 10-2 Define PDP Context: + CGDCONT Description: This Command specifies PDP contex t parameter valu es for a PDP context identified by the local context identification parame ter, <cid>. Four PDP c ontexts can be defined through MOXA software . A special form of th e set comm and, +CGDCONT= <cid>[...]

OnCell G2150I AT Command Set GPRS Commands 10-3 <PDP_address>: a string parameter that identifies the MT i n the address space a pplicable to the PDP. If the value is nu ll or omitted, th en a value m ay be provided by the TE durin g the PDP startup procedure, or a dynamic address w ill be requested. The read form of the command will return t[...]

OnCell G2150I AT Command Set GPRS Commands 10-4 A T+CGQREQ=? +CGQREQ: <PDP_type>, (li st of supported <precedence>s), (list o f su pported <delay>s), (list of supported <re liability>s) , (list of supported < peak>s), (list of s upported <mean>s) [<CR><LF>+CGQREQ: <PDP_type>, (list of supported [...]

OnCell G2150I AT Command Set GPRS Commands 10-5 <reliability>: numeric parameter that specifies the reliability class 0: Subscribe d 1: Up to 1 000 (8 kbits/ s). 2: Up to 2 000 (16 kbit s/ s). 3: Up to 4 000 (32 kbit s/ s). 4: Up to 8 000 (64 kbit s/ s). 5: Up to 16 000 (128 kbits/s). 6: Up to 32 000 (256 kbits/s). 7: Up to 64 000 (512 kbits/[...]

OnCell G2150I AT Command Set GPRS Commands 10-6 non-sensitive application that can cope with data loss. NOTE: For real-time traffic, th e QoS profile also requires ap propriate set tings for del ay and throughput. 3: Up to 4 000 (32 kbit s/ s). 4: Up to 8 000 (64 kbit s/ s). 5: Up to 16 000 (128 kbits/s). 6: Up to 32 000 (256 kbits/s). 7: Up to 64 [...]

OnCell G2150I AT Command Set GPRS Commands 10-7 Command Possible responses A T+CGQ MIN=[<cid> > [,<delay> [,<precedence [,< peak> [,<reliability .> [,<mean>]]]]] ] OK ERROR A T+CGQMIN? +CGQMIN: <cid>, <precedence >, <delay>, <reliability>, <peak>, <mean> [<CR><LF>+C[...]

OnCell G2150I AT Command Set GPRS Commands 10-8 A T +CGA TT=1 OK Defined values: <state>: indicates the state of GPRS attachment • 0: detached • 1: attached • 2: combined detach (GPRS and GSM de tach in th e same network request) • Other values are reserved and will result in an ERROR response to the execution command. PDP Context Act[...]

OnCell G2150I AT Command Set GPRS Commands 10-9 Enter Data State: +CGDATA Description: This command causes the MT to pe rform the necessary actions to set up communicat ion between the TE and the netwo rk. This m ay include pe rforming a G PRS attach and one PDP context activation. If the <cid > value is not defined to the MT, it will return [...]

OnCell G2150I AT Command Set GPRS Commands 10-10 A T+CGCLASS=? +CGCLASS: (“CG”,”CC”) OK A T+CGCLASS? +CGCLASS: “CC” OK Defined values: <class>: a string param eter that indicates the GPRS m obile class (in descendi ng order of functionality) ‧ A class A (highest) ‧ B class B ‧ CG class C in GPRS only mode ‧ CC class C in c[...]

OnCell G2150I AT Command Set GPRS Commands 10-11 Command Possible responses +CGSMS= [<service>] OK ERROR +CGSMS? +CGSMS: <service> OK +CGSMS=? +CGSMS: (list of cu rrently available <service>s) OK A T +CGSMS=0 OK A T+CGSMS=? +CGSMS: (0-3) OK Defined values: <service>: a numeric parameter whic h indicates the service or servic[...]

OnCell G2150I AT Command Set GPRS Commands 10-12 mode), if MT result code b uffer is ful l, the oldest ones can be discar ded. Defined events: The following unsolicited result cod es and the corresponding ev ents are defined: +GEV: REJECT <PDP_type>, <PDP_addr> A network request for PDP context activ atio n occurred when the MT was unab[...]

OnCell G2150I AT Command Set GPRS Commands 10-13 2: enable network registration and location information unsolicited result code +CGREG: <stat>[,<lac>,<ci>] <stat>: 0: not regist ered, ME is not curre ntly searching a new opera tor to regist er to 1: registere d, home net work 2: not registere d, but ME is currentl y searchi[...]

OnCell G2150I AT Command Set GPRS Commands 10-14 Network Requested PDP Context Activation In this mode of operation, the MT be haves like a n answering modem and accepts the normal V.25ter commands associated with answeri ng a call. If GPRS-specific configuration commands are required, they may be sent to the MT as part of the modem initial izatio [...]

OnCell G2150I AT Command Set GPRS Commands 10-15 Command syntax: Command Possible responses +CGAUT O=[<n>] OK ERROR +CGAUT O? +CGAUT O: <n> OK +CGAUT O=? +CGAUT O: (0-3) OK Defined values: <n>: 0 turn off automatic response fo r GPRS only 1 turn on automat ic response for GPRS onl y 2 modem compatibility mode , GPRS only 3 modem c[...]

OnCell G2150I AT Command Set GPRS Commands 10-16 During the PDP startup procedure the MT has the PDP type and the PDP address provided by the network in the Request PDP Context Activation message. If a <cid> is given its information must match th e PDP type and PDP address in the network request as follows: The PDP typ e must match exactly. T[...]

OnCell G2150I AT Command Set GPRS Commands 10-17 Show PDP Address: +CGPADDR Description: The exclusion command returns a lot of PDP addresses for the specified context identifiers. The test command retu rn s a list of defined <cid>s Command syntax: Command Possible responses +CGP ADDR=[<cid > [,<cid> [,…]]] +CGP ADD R: <cid&g[...]

OnCell G2150I AT Command Set GPRS Commands 10-18 +CRING: GP RS GPRS network request for PDP context act ivation If the MT is u nable to anno unce to the TE t he network’s request (fo r exam ple it is in V.25t er on line data state) the MT rejects th e request. No corresponding unsolicited result code is issued when the MT returns to a comm and st[...]

OnCell G2150I AT Command Set GPRS Commands 10-19 GPRS Parameter Customization: + WGPRS Description: This command modi fies some G2150I GP RS param eters: ‧ the ATTACH-STAT US (the ME does or not perform automatically a GPRS attachment after initialization), ‧ the PDP-IN IT-STATU S ( activ ates automat ically or no t some define d PDP context s [...]

OnCell G2150I AT Command Set GPRS Commands 10-20 Command Possible responses AT + W G P R S ? Note: - Automatic re-attachment at init not activated - Automatic reactivation of PDP context at init not activ ated - 3 PDP contexts, and a utomat ic reactivation only for Cid 1 - PPP silent mode activated - GPRS class is 8 - GPRS slow connect activated - [...]

OnCell G2150I AT Command Set GPRS Commands 10-21 some OS-speci fic frames, for accurate trans fer rate measurem ents. <parameter>: a numeric parameter that cont rols the operation defined by < mode> if it is equal to 0, 1, 2, or 3. 0 operation OFF (disabled) 1 operation ON (enabled) <cid>: (PDP Context Identifier)a numeric para me[...]

OnCell G2150I AT Command Set GPRS Commands 10-22 Example 2: AT + C G C L A S S = ” C G ” OK +CGREG: 1 A T +CGDCONT=1,” IP”,”intern et” OK A T +CGQREQ=1,1,4,5,2,14 OK A T +CGQMIN=1,1,4,5,2,14 OK AT + C G AT T = 1 OK A T +CGACT=1,1 OK Remark a bout +CGD A T A : The goal of this command is the same as A TD*99***A T + CGDA T A=1 CONNECT …[...]

1 1 1 1 Chapter 11 MOXA Proprietary Commands This chapter includ es information ab ou t the MO XA propri et ary Com m ands of the OnCel l G2150 I. The following topics are covered in this chapter:  Firmware Upgrade: *UPG  Restore Defau lt Settin g: * D EFAULT  Automatic PI N Entry: *US EPIN  Initial Strings: *BOOTSTR  Serial Port Con[...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-2 Firmware Upgrade: *UPG Description: This command trigge rs a X-m odem(checksum) downloa ding session f or G2150I firmware image. . Notes: • There will always be risks when performing the firmware upgrade. Ensu re to have fixed p hysical con nection on b oth the powe r and the si gnal lin[...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-3 Restore Default Setting: *DEFAULT Description: Th is command resets the G2150I to its factory default. Example AT * D E F A U LT *DEF AUL T : reset modem configurations Restoring modem defa ult s, please wit… OK Clean-up, please wait… Clean-up OK All Done!! OK +WIND: 13 NOTE Upgrading [...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-4 Automatic PIN Entry: *USEPIN Description: This command enables/disables the automatic PIN code entry function when G2150I is bo oting up Command syntax: AT*USEPIN=<n>, <PIN Code> Command Possible responses A T*U SEPIN=1, 1234 Note: 1234 is an example of PIN code OK Note: Done A[...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-5 Initial Strings: *BOOTSTR Description: Th is command enables/disables the initial strings Command syntax: AT*BOOTSTR=<m> AT*BOOTSTR<n>=<in itial strings> Command Possible responses A T*BOOTSTR=1 OK Note: Done A T*BOOTSTR=0 OK Note: Done At*BOOTSTR =? Note: list the usage [...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-6 Serial Port Configuration: *SERIAL Description: Th is command configures the serial port setting s Command syntax: AT*SERIAL=<n>,<baudrate>,<data bits>,”< parity>“,<stop bits>,”<flow control>“ Command Possible responses A T*SERIAL? *SERIAL: (0, 1[...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-7 SMS Tunnel Mode: *SMS Description: This command confi gures the SMS T unnel m ode settings Command syntax: AT*SMSIN=<encoding>,<recei ve phone 1>,<receive phone 2> AT*SMSOUT=<encoding>,< ta rget pho ne 1>,<t ar get ph o ne 2> AT*SMSTUN=<n> AT*SMSIO[...]

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-8 *SMSOUT : Configured Encode: 7-Bits GSM T ext Receiver1: +8862891912 30 Receiver2: +8862891912 31 A T*SMSIN=0,+886289191230,+886289191231 *SMSIN: Configured Encode: 7-Bits GSM T ext Sender1: +88628919123 0 Sender2: +88628919123 1 OK A T *SMSTUN=1 OK AT SMSOUT : Enter SMS T unnel Mode… En[...]

A A Appendix A Result Codes, Failure Causes, and Other Tables This chapter includ e s in formation about the Result Codes, Failure Causes, and Other Tables of the OnCell G2150I. The following topics are covered in this chapter:  ME Error Result Code: +CME ERROR: <error>  Message Ser vice Failure Result Code: +CMS E RROR: <er>  [...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-2 ME Error Result Code: +CME ERROR: <error> <error> Meaning Re s ulting from the follo w in g commands 3 Operat ion not allow ed All GSM 07.07 commands ( +CME ERRO R: 3) 4 Operat ion not suppo rted All GSM 07.07 comm ands (+CME ERR OR: 4) 5 PH-SIM PIN requi [...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-3 148 unspec ified GPR S error All GPRS comma nds 149 PDP aut hentication failure +CGACT +CGDATA ATD*99 150 invalid mobile class +CGCLASS +CGATT Message Service Failure Result Code: +CMS ERROR: <er> <er> Meaning Resulting from the follo w in g commands 1 to [...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-4 518 SIM ToolKit indication not received. +ST GI 519 Reset the product to activate or change a new echo cancellation algo. +ECHO, +VIP 520 Automatic abort about get plmn list for an incoming call. +COPS=? 526 PIN deact ivation forbi dden with this SIM card. +CLCK 527 P[...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-5 29 Facility rejected 30 Response to STATUS ENQUIRY 31 Normal, unspecified 34 No circuit/channel available 38 Network out of order 41 Temporary failure 42 Switching equipment congestion 43 Access information discarded 44 Requested circuit/channel not available 47 Resou[...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-6 231 PDP deactivation cause LLC link activation failed 232 PDP deactivation cause NWK reactivation wit h same TI 233 PDP deactivation cause GMM abort 234 PDP deactivation cause LLC or SND CP failure 235 PDP unsuccessful activation cause GMM error 236 PDP unsuccessful a[...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-7 Cause No. 21 : “Short m essage transfer rejected” This cause indi cates that the equipm ent sending this cause does not wish to accept this short message, although it could ha ve accepted the short m essage since the equipment sending this cause is neith er busy n[...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-8 mandatory i nformati on element is missing a nd/ or has a content error (t he two cases are undistin guishabl e). Cause No. 97 : “Message t ype non -existent or not impl emented” This cause indi cates that the equipm ent sending this cause has received a message w[...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-9 +CLIP: <num ber>, <type> [,,,<alpha>] As verbose Incomi ng Call Presenta tion + C M T : < o a > … ( t e x t mode) or +CMT: [<al pha>,]… (PDU) As verbose Incoming m essage di rect l y displayed +CMTI: <m em>,<index> As verb[...]

OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-10 Intermediate Result Codes Verbose Result Code Numeric (V 0 set) Description Verbose Result Code Nu meric (V0 set) Description +COLP:<number> ,<type> as ve rbose Outgoing Call Presentation +CR: <type> as verbose Outgoing Ca ll report cont rol +ILRR: [...]