Razor MX350 15128050 manual

TM O W N E R ’ S M A N U A L Read and underst and this entire manu al before riding! Item Numbers: Dirt Rocket MX350 1512805 0 Dirt Rocket MX500 151281 90 Dirt Rocket MX650 1516507 0[...]

WARNING: Riding an electric motorbike can be a hazardous activity . Certain conditions may cause the equipment to fail without fault of the manufacturer . Like other electric vehicles, the Dirt Rocket can and is intended to move, and it is therefore possible to lose control, fall off and/or get into dangerous situations that no amount of care, inst[...]

Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the Dirt Rocket was 95 percent assembled and packed at the factory , there should not be any problems, even i[...]

Attaching the Front F orks – MX350 2 Insert the spacer sleeves on the top and bottom of the frame. 3 Slide the fork into position and insert the steering bolt. The bolt must go through the washer and spacer sleeve and between the steering bearings inside the frame. 1 Remove steering bolt, spacer sleeves, washers and nut from front fork assembly .[...]

1 Using a 5mm hexagonal key wrench, remove bolts from handlebar clamp. 2 Place handlebars in handle- bar clamp and adjust angle parallel to the fork. 3 Insert bolts and tighten securely . When properly tightened, the handlebars should not move forward or back. Attaching the Handleb ars WA RNING: Failing to properly adjust and tighten the bolts that[...]

1 T o adjust the play , thread the brake lever adjuster in or out 1/4 to 1/2 turn until the desired brake adjustment is attained. Most adjustments are complete at this step. If brake still needs further adjustment, proceed to step 2. 2 If the brake lever adjuster is threaded outward and the brake still has too much slack, use the back brake adjuste[...]

6 REP AIR AND MAINTE NANCE q Chain and Rear T ire Replacemen t – MX350 Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 2 With a 10mm wrench, loosen the brake cable anchor and disconnect the cable. 3 With two 8mm wrenches, loosen brake housing anchor and disconnect. Keep the spacer and washers together . 4 With two 17[...]

REP AIR AND MAINTE NANCE q Chain and T ire Replacement – M X500 / MX650 Tools required: Phillips screwdriver and two (2) 17mm wrenches. 1 Loosen screw and remove chain guard. 2 Loosen the rear axle by attaching wrenches to both axle nuts and loosening counter - clockwise. 3 Push the chain tensioner down to slacken the chain and disengage the chai[...]

8 REP AIR AND MAINTE NANCE q Replacing the Fuse – MX350 / MX500 / MX650 WA RNING: T o prevent shock or short circuit, please follow the instructions accordingly and do not skip or combine any steps. 1 Remove the fairing/body cover . 2 Locate the fuse cover attached to the batteries. 3 Open the fuse cover to expose the fuse. 4 Remove the fuse and [...]

9 REP AIR AND MAINTE NANCE q Chain and Sprocket The chain will typically have a “loose spot” and “tight spot” corresponding with a particular sprocket rotational position. This is normal and common to all chain-driven vehicles due to run-out tolerances of the freewheel and sprocket. The chain should be adjusted to the ideal tension with cha[...]

10 SB 1918 (CALIFORNIA) DECLARA TION YOUR INSURANCE POLICIES MA Y NOT PROVIDE COVERAGE FOR ACCIDENTS INVOL VING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONT ACT YOUR INSURANCE COMP ANY OR AGENT .[...]

11 V ehicle does not run V ehicle was running but suddenly stopped Short run time (less than 30 minutes per charge) V ehicle runs sluggishly TROUBLES HOOTING GUID E Problem Possible Cause Solution Undercharged battery Charger is not working Loose wires or connectors Burned-out fuse Motor or electrical switch damage Undercharged battery Battery is o[...]

Sometimes the vehicle doesn’t run, but other times it does Charger gets warm during use V ehicle does not stop when applying the brake V ehicle makes loud noises or grinding sounds Need Help? V isit our web site for updates and a list of author ized service c enters at www .razor .com or call toll-fre e at 866-467-2 967 Monday - F riday 8:00 AM -[...]

13 Keep your MX350 running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability . (Specifications subject to change without notice.) MX350 P AR TS 1. Handlebar end cap 2. Grip, half length 3. Speed control, twist grip 4. Handlebar 5 Handlebar foam padding 6. Handlebar pad cover 7. Fend[...]

MX350 P AR TS 14[...]

15 Keep your MX500/MX650 running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability . (Specifications subject to change without notice.) MX500 / MX650 P ARTS 1. Fender , front 2. Cover , handlebar pad 3. Handlebar foam padding 4. Clamp, handlebar , upper 5. Clamp, handlebar , lower 6[...]

MX500 / MX650 P ARTS 16[...]

T ire Inflation Periodically inspect the t ires for excess wear and replace as required, and regularly ch eck the tire pressure and re-infl ate as necessary . If you get a flat tire, the inner tube can be patched or a new tube can be purchased from Razor or an authorized repair center . Safety Gear Always wear proper protect ive equipment, such [...]