RIDGID R86014 manual

1 Y our drill has been en gineer ed and manufactur ed to our high standar ds for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance. WARNING: T o reduce the risk of injury , the user must read and understand the operator’ s manual before using this pr oduc[...]

2  Introduction......................................................................................................................................................................2  General Safety Rules .....................................................................................................................................[...]

3 GENERAL SAFETY RULES WARNING! RE AD AN D U NDE RS T A ND ALL IN ST RUC TI ON S. Failure to follow all instructions listed below , may r esult in elect ric sho ck, fir e and /or ser ious person al injury . SA VE THESE INSTRUCTIONS WORK AREA  Keep your work area clean and well lit. Clu t te red benches and dark areas invite accidents.  [...]

4 GENERAL SAFETY RULES SPECIFIC SAFETY RULES  H o l d t o o l b y i n s u l a t e d g r i p p i n g s u r f a c e s w h e n performing an operation where the cutting tool may con tact hidd en wiring . Con tact with a “live” wir e will also make exposed metal parts of the tool “live” and shock the operator .  Know your power tool[...]

5 SYMBOLS Some of the following symbols may be used on this product. Please study them and lear n their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer . V V olts V oltage A Amperes Current Hz Hertz Frequency (cycles per second) W W att Power min Minutes Time Alternating Current T ype of curre[...]

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts. WARNING: T o avoid serious personal injury , do not attempt to us[...]

7 FEA TURES PRODUCT SPECIFICA TIONS Chuck ...........................................................1/2 in. Keyless Motor .................................................................. 18 V olt DC Switch .......................................................... V ariable Speed No Load Speed ....................... 0-450/0-1,450 r/min. (RPM) C[...]

8 UNP ACKING This product has been shipped completely assembled.  Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the product carefully to make sure no breakage or damage occurred during shipping.  Do not discard the packing material until you have ca[...]

9 TO INST ALL BA TTER Y P ACK See Figure 2.  Lock the switch trigger on the drill by placing the direc- tion of rotation (forward/reverse/center lock) selector in center position.  Place battery pack in the drill. Align raised rib on battery pack with the groove inside the drill.  Make sure the latches on each side of the battery pack snap[...]

10 OPERA TION CAUTION: T o prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of r otation. T o stop the drill, release the switch trigger and allow the chuck to come to a complete stop. NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right. Avoi[...]

11 OPERA TION Fig. 7 Fig. 8 Fig. 9 DRILL BIT OPEN (RELEASE) CHUCK JA WS GRIP (TIGHTEN) CHUCK BODY KEYLESS CHUCK RIGHT WRONG LED LIGHT See Figure 7. The LED light on the foot of the drill will come on when the switch trigger is depressed . This provi des additional lighting on the surface of the workpiece for operation in lower -light areas. INST AL[...]

12 OPERA TION Fig. 10 DRILLING See Figure 10.  Check the direction of r otation selector for the correct setting (forward or r everse).  Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.  Hold the drill firmly and place the bit at the point to be drilled.  Depress the s[...]

13 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replacement parts. Use of any other parts may create a hazar d or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty , also wear a dust mask. WARNING: T o avoid seriou[...]

14 MAINTENANCE CHUCK REMOV AL See Figures 11 - 13. The chuck may be removed and r eplaced by a new one.  Lock the swit ch trig ger by placing the dir ect ion of rota tion selector in center position.  Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely .  T ap the hex key sharply wit[...]

15 W ARRANTY Proof of purchase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be dir ected to One W orld T ec hno[...]

16 OPERA TOR’S MANUAL 1/2 in. 18 VOL T LITHIUM-ION AutoShift ™ DRILL R86014 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all r elevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or [...]