Star Micronics TSP100 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Ir para a página of

Bom manual de uso

As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Star Micronics TSP100. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoStar Micronics TSP100 vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.

O que é a instrução?

A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Star Micronics TSP100 você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.

Infelizmente, pequenos usuários tomam o tempo para ler o manual Star Micronics TSP100, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.

Então, o que deve conter o manual perfeito?

Primeiro, o manual Star Micronics TSP100 deve conte:
- dados técnicos do dispositivo Star Micronics TSP100
- nome do fabricante e ano de fabricação do dispositivo Star Micronics TSP100
- instruções de utilização, regulação e manutenção do dispositivo Star Micronics TSP100
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes

Por que você não ler manuais?

Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Star Micronics TSP100 não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Star Micronics TSP100 e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Star Micronics na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Star Micronics TSP100, como para a versão papel.

Por que ler manuais?

Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Star Micronics TSP100, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.

Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Star Micronics TSP100. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação

Índice do manual

  • Página 1

    Hardware Manual[...]

  • Página 2

    Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ[...]

  • Página 3

    T ABLE OF CONTENTS 1. Unpacking and Installation .......................................................................... 1 1-1. Unpacking ........................................................................................... 1 2. Parts Identification and Nomenclature ...................................................... 2 3. Setup ........[...]

  • Página 4

    – 1 – 1-1. Unpacking After unpacking the unit, check that all the necessary accessories are included in the package. Fig. 1-1 Unpacking If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case y[...]

  • Página 5

    – 2 – 2. Parts Identification and Nomenclature Cover open lever Pull this lever in the direction of the arrow to open the printer cover. Control panel Features LED indica- tors to indicate printer status and switches to operate the printer. Power switch Used to turn on/off power to the printer. Power connector For connection of the power cord. [...]

  • Página 6

    – 3 – Tear Bar Model Cover open lever Pull this lever in the direction of the arrow to open the printer cover. Power connector For connection of the power cord. Peripheral drive connector Connects to peripheral units such as cash drawers, etc. Do not connect this to a telephone. Interface connector For connection to a host computer. Printer cov[...]

  • Página 7

    – 4 – Choosing a place for the printer Before actually unpacking the printer, you should take a few minutes to think about where you plan to use it. Remember the following points when doing this. ✓ Choose a firm, level surface where the printer will not be exposed to vibration. ✓ The power outlet you plan to connect to for power should be n[...]

  • Página 8

    – 5 – 3. Setup 3-1. Connecting the USB Cable to the Printer Affix the ferrite core onto the USB interface cable and pass the cable through the cable support as shown. Then, connect the USB interface cable to the printer. Note: The dialog shown below may appear on your PC screen if your PC is running Windows 98 or Me, and if you turn ON the powe[...]

  • Página 9

    – 6 – 3-2. Connecting to a Peripheral Unit You can connect a peripheral unit to the printer using a modular plug. The following describes how to install the ferrite core and make the actual connection. See “ Modular plug ” on page 24 for details about the type of modular plug that is required. Note that this printer does not come with a mod[...]

  • Página 10

    – 7 – 3-3. Loading the Roll Paper Be sure to use roll paper that matches the printer ’ s specification. When using a paper roll with an 57.5 mm width, install the paper roll holder as described on the following page. 1) Push the cover open lever, and open the printer cover. 2) While observing the direction of the roll, set the paper roll into[...]

  • Página 11

    – 8 – Note: When using a paper roll with an 57.5 mm width, install the paper roll holder in the groove in the printer. If a paper roll with a 57.5 mm width has been used, a paper roll with a 79.5 mm width cannot be used. (Changing from the smaller roll to a larger roll will cause part of the print head to rub against the platen and deteriorate.[...]

  • Página 12

    – 9 – WARNING • Do not touch the cutter blade. - There is a cutter inside the paper outlet slot. Not only should you not put your hand in the paper outlet slot while printing is in progress, never put your hand into the outlet even when printing is not in progress. - The printer cover can be opened when replacing the paper. How- ever, since t[...]

  • Página 13

    – 10 – 3-4. Connecting the USB Cable to the PC Connect the USB interface cable to a USB port of your PC. Note: The dialog shown below may appear on your PC screen if your PC is run- ning Windows 98 or Me, and if you turn ON the power of the printer for the first time while the PC and the printer are connected with the USB cable. In this case, r[...]

  • Página 14

    – 11 – 3-6. Connecting the Power Cord Note: Before connecting/disconnecting the power cord, make sure that power to the printer and all the devices connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet. (1) Check the label on the back or bottom of the printer to make sure its voltage matc[...]

  • Página 15

    – 12 – Power switch 3-7. T urning Power On Make sure that the Power cord has been connected as described in 3-6. (1) Turn ON the power switch located on the front of the printer. The POWER lamp on the control panel will light up. CAUTION We recommend that you unplug the printer from the power outlet whenever you do not plan to use it for long p[...]

  • Página 16

    – 13 – 4-1. Attaching the Holder Plate ( 1) Attach the holding plate to the printer. Then tighten the two screws that were supplied to secure it in place. (2) Position the printer over the wall bracket and then slide it downward to set it in place. The printer is fixed in place by inter- locking the hook on the plate at- tached to the bottom of[...]

  • Página 17

    – 14 – 4-2. Attaching the Rubber Feet (1) Attach the four rubber feet in the positions shown in the figure. Ensure that any soiling has been completely wiped off before attach- ing the rubber feet. (2) Push the cover open lever, and open the printer cover. (3) Insert the roll paper as shown.[...]

  • Página 18

    – 15 – 4-3. Switch Blind Installation It is not necessary to install the switch blind. Only install it if it is necessary for you. By installing the switch blind, the following become possible. • Preventing the power switch from being operated by mistake. • Ensuring that other people can not easily operate the power switch. Install the swit[...]

  • Página 19

    – 16 – 5. T ermal Roll Paper Specification When consumable parts have run out, use those specified below. (1) Roll paper specification Thermal paper Thickness: 65~85 µ m (excluding Mitsubishi HiTec F5041) Width: 79.5±0.5 mm (57.5±0.5 mm when the paper roller holder is used) Outer roll diameter: ø 83 mm or less Take up paper roll width: 80 m[...]

  • Página 20

    – 17 – 6. Control Panel and Other Functions 6-1. Contr ol Panel 1 POWER lamp (Green LED) Lights when the power is ON. 2 ERROR lamp (Red LED) Indicates various errors in combi- nation with POWER lamp. 3 FEED button Press the FEED button to feed roll paper. 6-2. Err ors 1) Automatically recoverable errors 1 POWER lamp (Green LED) 3 FEED button 2 [...]

  • Página 21

    – 18 – 2) Non-recoverable errors Note: 1) If a non-recoverable error occurs, turn the power OFF immediately. 2) If a non-recoverable error occurs, please consult the dealer for repairs. 3) Paper cut error Note: If the cutter does not return to its home position or does not perform the initial movement, it will result in a non-recoverable error.[...]

  • Página 22

    – 19 – 6-3. Self-Printing Test Printing Turn the power ON while holding the FEED button depressed. The printer will run a test print according to the Ver. No., DIP switch settings, and character order. After the printer starts printing, release your hand from the FEED button. After self-printing is completed, the printer will start in the norma[...]

  • Página 23

    – 20 – 7. Preventing and Clearing Paper Jams 7-1. Pr eventing Paper Jams The paper should not be touched during ejection and before it is cut. Pressing or pulling the paper during ejection may cause a paper jam, paper cutting failure or line feed failure. 7-2. Removing Paper Jam If a paper jam occurs, clear it as described below. (1) Set the po[...]

  • Página 24

    – 21 – 7-3. Releasing a Locked Cutter (Auto Cutter Mode only) If the auto cutter locks up or fails to cut the paper, follow the steps below. WARNING Since working on the cutter may be dangerous, be sure to turn off the printer first. (1) Set the power switch to OFF to turn off the printer. (2) Remove the front cover to reveal the auto cutter. ([...]

  • Página 25

    – 22 – (4) If the cutter is locked, insert a Philips screwdriver into the Philips screw hole on the side of the cutter, and turn it in the direction of the arrow shown on the right, in order to return the cutter to its normal position. (5) Open the printer cover, remove any jammed paper, and then reinstall the paper roll. (6) Install the front [...]

  • Página 26

    – 23 – 8. Periodical Cleaning Printed characters may become partially unclear due to accumulated paper dust and dirt. To prevent such a problem, paper dust collected in the paper holder and paper transport section and on the surface of the thermal head must be removed periodically. Such cleaning is recommended to be carried out once six month o[...]

  • Página 27

    – 24 – E C R3 R4 R3 = 3.5k Ω R4 = 300 Ω B Modular plug Peripheral Drive Connector Pin No. Signal Function I/O name direction 1 FG Frame ground — 2 DRD1 Drive signal 1 OUT 3 +24V Drive power OUT 4 +24V Drive power OUT 5 DRD2 Drive signal 2 OUT 6 DRSNS Sense signal IN 9. Periheral Unit Drive Circuit Peripheral unit drive circuit connector o[...]

  • Página 28

    – 25 – Notes: 1. Pin 1 must be shield drain wire connected to peripheral device frame ground. 2. It is not possible to drive two drives simultaneously. 3. The peripheral drive duty must satisfy the following: ON time / (ON time + OFF time) 0.2 4. Minimum resistance for coils L1 and L2 is 24 Ω . 5. Absolute maximum ratings for diodes D1 and D2[...]

  • Página 29

    – 26 – 10-1. General Specifications (1) Printing method Direct line thermal printing (2) Print speed Max. 1000 dots/sec. (125 mm/sec.) (3) Dot density 203 dpi: 8 dots/mm (0.125 mm/dot) (4) Printing width Max. 72 mm (5) Roll paper Refer to chapter 5 for details on the recommended roll paper. Paper width:79.5±0.5 mm (57.5±0.5 mm when the paper [...]

  • Página 30

    – 27 – 10-2. Auto Cutter Specifications (1) Cutting frequency Max. 20 cuts per minute (2) Thickness of paper 65~85 µ m 10-3. Interface (1) Specifications USB 2.0 full speed Printer class and vendor class compatible (2) Connector Type B 10-4. Electrical Characteristics (1) Input Voltage 100 to 240 V AC, 50/60 Hz (2) Current Consumption Operatin[...]

  • Página 31

    – 28 – 10-6. Reliability 1) Life Mechanical: 20 million lines Head: 100 million pulses, 100 km (±15% max. aver- age head resistance fluctuation) For 2-color printing, 50 million pulses, 50 km (±15% max. average head resistance fluctua- tion) Auto cutter: 1 million cuttings (provided the paper thick- ness is between 65 and 85 µ m) <Conditi[...]

  • Página 32

    2005.08.20 Printed in China, 80870415CD ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushiny a, Shimizu-ku, Shizuoka, 42 4-0066 J apan T el: 0543-47-0112, F ax: 0543-48-5013 Please access the f ollowing URL http://www .star-m.jp/ eng/dl/dl02.htm f or the lastest re vision of the manual. OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS[...]