Zanussi ZGF782C manual

GAS HOB ZGF782C INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB[...]

2 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V olt ageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Import ant Safety Information You MUST read hese warnings carefully before installing or using the ho[...]

3 For the User Content s For the Installer 1. Auxiliary Burner 2. Semi-rapid Burners 3. Ultra-rapid Triple-crown Burner 4. Rapid Burner 5. Control knobs Description of the Hob Important Safe ty Informat ion 2 Description of the Hob 3 Operation 4 Maintenance and Cleaning 4 Something Not Working? 5 Guarantee Conditions 6 Instructions for the Installe[...]

4 Maintenance and Cleaning Operation Hob burners T o light a burner: l push in the relevant control knob and turn it anticlockwise to maximum position; l then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. T o ensure maximum burner efficiency , you should only use pot s and pans with a fla[...]

5 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre. SYMPTOM n There is no spark when lighting the gas n The gas ring burns unevenly SOLUTION u Check that the unit is plugged in and the electrical supply is switched on u Check that the RCCB h[...]

6 In the event of your appliance requiring service, or if you wish to purchase spare part s, please contact your local Zanussi Service Force Centre by telephoning: 0870 5 929929 Y our telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further i[...]

7 OVERALL DIMENSIONS W idth: 680 mm. Depth: 510 mm. CUT OUT DIMENSIONS W idth: 560 mm. Depth: 480 mm. SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply , 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. Ignition HT Spark S park Generator Ispra Control's BF[...]

8 FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 400 mm 100 mm 55 mm 50 mm 50 mm 600 mm 700 mm 400 mm 400 mm 100 mm 55 mm 600 mm 50 mm 50 mm FO 2369* FO 2231* Import ant safety requirement s This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Cu[...]

9 Inst allation IMPORTANT: This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI instal ler . The manufacturer will not accept liability , should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE [...]

10 FO 2564 FO 2044 3 50 50 FO 2039 Dimensions are given in mm. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the[...]

11 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240[...]

12 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all c[...]

13 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

14 Commissioning When the hob has been fully inst alled it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas t ap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguis[...]

15[...]

35669-7305 02/03 Grafiche MDM - Forlì CUST OMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux plc 2003 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux[...]