Cisco Blower Module Cisco 10000 ESR инструкция обслуживания

Corporate Headqu arters: Cisco Systems, Inc., 170 We st Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 20 0 0. Cisco Systems, Inc. All rights reserved. 78-10832-01 Cisco 10000 ESR AC Power Entry Module Installation This publication contains instructions for installing the A C Po wer Entry Module (PEM) in the Cisco 10000 Edge Services Router[...]

Product Description 2 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Product Description The A C PEM provides po wer con version directly fro m the facility V A C input po wer (100 V A C to 240 V A C) to the –48V VDC used internally b y the system (see Figure 1). A C power is deli v ered to the A C PEM from the V A C connection p[...]

3 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Prerequisites and Preparation Prerequisites and Preparation Before you perform an y of the p rocedures in this guide, Cisco recommend s that you: • Read the safety guidelin es in the nex t section and re vie w the electrical safety and ESD-pre vention guidelines in the Cisco 10000 [...]

Installation Guidelines 4 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 War ni ng This warning symbo l means danger . Y ou are in a situation that could cause bodily inju ry . Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard p ractices for preventing accide [...]

5 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Adding or Replacing an AC PEM This section describes how to add or replace an A C PEM in the Cisco 10000 chassis. It contains the follo wing procedures: • Remov ing the Front Cov er , page 5 • Installing a Second A C PEM, page 7 • Replacing an A C [...]

Adding or Replacing an A C PEM 6 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Remov e the cov er by li fting it up sli ghtly and then pulling it t o ward you (Figure 3). Figur e 3 Removing the Fr ont Cov er Step 3 Continue instal ling or replacing the A C PEM: • If you are installing a second A C PEM, go to the “I nsta[...]

7 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Installing a Second AC PEM Use the follo wing procedure to install a second A C PEM in the bottom po wer bay for redundanc y . Step 1 Attach an antistatic wr ist strap to your wr ist and to an ESD socket on the chassis, or to a bare metal surf ace on the[...]

Adding or Replacing an A C PEM 8 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Loosen the capti v e scre ws to remov e the blank co v er from the bottom po wer bay (Figure 5). Figur e 5 Removing the Blank Co v er 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FAN FAILURE W h e n h o t s w a p p in g th is fa n tr[...]

9 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 3 Install the ne w AC PEM all t he way into the po wer bay to ensure a secure connection to the backplane, and then tighten the captive scre ws (Figure 6 ). Figur e 6 Installing an A C PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FA[...]

Adding or Replacing an A C PEM 10 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 4 Connect the po wer cord from the PEM to your po wer cord that connects to th e faci lity V A C input. Step 5 Set the A C power cord connec tors in a cord st rain relief (canoe) to pre vent them from accidently di sconnecting (Figu re 7). Figur e[...]

11 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 7 Set the po wer switch to the on (|) positi on (Figure 8). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 8 Setting the A C P ow er S witch t o the On P osition Step 8 Replace the front cover . 32231 1 3 2 4 0A P R[...]

Adding or Replacing an A C PEM 12 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Replacing an AC PEM Use the following procedure to replace an A C PEM. Note The illustrations in this guide sho w how to replace the A C PEM from the bottom po wer bay . The procedure is the same to replace an A C PEM in the top po wer bay . Step 1 Att[...]

13 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 2 Po wer of f the PEM you are replacing (Figure 10). Caution Do not po wer off both A C PEMs in a redundant system or the system shuts do wn and all data traff ic stops. Only po wer of f the A C PEM you are replacing. Figur e 1 0 Sett ing the A C P[...]

Adding or Replacing an A C PEM 14 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 3 Remov e the PEM power cable from its can o e and disconnect it from the A C input po wer cable (Figure 11). Figur e 1 1 AC P ow er Cor d Connect ors in Canoes 32235 1 3 2 4 0A PR O C E SS O R O N LY 0B 5 6 7 8 P R O CE S SO R O N LY POWER FAULT [...]

15 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 4 Loosen the captiv e scre ws on the PEM and remo ve the PEM from the chassis using the handle on the faceplate (Figure 12). Figur e 12 Removing an A C PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FAN FAILURE W h e n h o t s w a p [...]

Adding or Replacing an A C PEM 16 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 5 Install the ne w PEM all the way into the po wer bay to ensure a good connection to the backplane, and tighten the ca ptiv e scre ws on the PEM (Figure 13). Figur e 13 Installing an AC PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI[...]

17 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 6 Connect the po wer cord from the PEM to the po wer cord that connects to the faci lity V A C input. Step 7 Set the A C power cord connec tors in a cord st rain relief (canoe) to pre vent them from accidentl y disconnecting ( Figure 14). Figur e 1[...]

Adding or Replacing an A C PEM 18 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 9 Set the po wer switch to the on (|) positi on (Figure 15) . The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 15 Set ting the A C P ow er Switc h t o the On P osition Step 10 Replace the front cover . 32231 1 3 2 4 [...]

19 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Troubleshooting the Installation T able 1 contai ns troubleshooting i nformation for th e A C PEM: T able 1 A C PEM T r oubleshooti ng Symptom Description System fails to power on Check that : • All A C pow er cords are properly connected to the Cisco[...]

FCC Class A Compliance 20 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 FCC Class A Compliance This equipment has been tested and found to comply wi th the limits for a Class A digital de vice, pursuant to part 15 of the FCC rules. These limits are desi gned to pro vide reas onable p rotection agains t harmful i nterferen ce when [...]

21 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Cisco Connection Online A vail able 24 hours a day , 7 days a week , CCO pro vides a wealth of standard and v alue-added services to Ci sco customers and b usiness partners. CCO services include prod uct information, product do cumentation, softw are updates, release notes, technica[...]

Documentation CD-ROM 22 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Documentation CD-ROM Cisco documentation and add itional lite rature are a vailable in a CD-R OM package, which ships with your p roduct. The Documentation CD-R OM, a member of the Cisco Connectio n Family , is updated mon thly . Therefore, it might be more curr[...]