Craftsman 536,884,791 инструкция обслуживания

5.0 Horsepower 22 Inch Dual Stage 120V, Electric Start SNOW THROWER MODEL NO, 536,884791 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product, SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. F-O01070J 07/27/99[...]

il nP':_:) H= [o]= [o,[o]'_lld=l_',] Table of Contents 2 Service and Adjustments 14-t6 Warranty 2 Storage 17 Safety Rules 2-4 Troubleshooting 18 Contents of Shipping Carton 4-5 Repair Parts 20-26 Assembly 5-7 Engine Repair Parts 27-31 Operation 8-12 Spanish (Espa5ol) 32-51 Maintenance 12-14 Parts Ordedng,'Service Back Cover LIMI[...]

PREPARATION 1. Thoroughly inspect the area where the snow thrower is to be used and remove all doormats, sleds, boards, wires and other foreign objects. 2. Disengage all clutches before starting the engine (motor). 3. Do not operate the snow thrower without wearing adequate winter outer garments. Wear footwear that will improve footing on slippery [...]

16. Never direct discharge at bystanders or allow anyone in front of the snow thrower. 17. Disengage power to the auger/impeller when snow thrower is transported or not in use. 18. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc). 19. Never operate the snow thrower[...]

Parts packed separately in carton (not shown full size) 2 - Ignition Keys (Attached to engine in plastic bag) 1 - Crank Assembly 1 - Snow Chute Assembly ,4k CAUTION: Always wear safety glasses or eye shields while assembling snow thrower. TOOLS REQUIRED FOR ASSEMBLY 1 - Knife (to cut carton and plastic ties) 2- 1/2 inch wrenches (or adjustable wren[...]

• Remove and discard the packing material from around the snowthrower. • Cut all four corners of the carton from top to bottom and lay the panels flat. • Cut ties securing the clutch control cable to the lower handle and lay cable back away from the motor frame. • Standing at rear, tilt snowthrower forward and remove packaging under motor f[...]

• Carefully remove cotter pin, clevis pin and drilled pin from yoke end of crank rod assembly (see figure below). • Place universal joint into end of worm gear lining up large holes. Insert drilled pin (ensure opening in pin is in line with small openings in universal joint) (see figure below). • Place yoke end of crank rod around universal j[...]

Eo to] KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. r Drive Lever Primer Button Electric Starter Button Discharge Ignition[...]

Auger Drive Clutch Ignition Key insert to run pull out to stop Z_ CAUTION: Read owner's manual before operating machine. Never direct discharge toward bystanders. Release the auger control bar and stop the engine before unclogging discharge chute or auger housing and before leaving the machine. The operation of any snow thrower can re- sult in[...]

BEFORE STARTING THE ENGINE • If the snow thrower must be moved with- out the aid of the engine, it is easier to pull the snow thrower by the handles rather than pushing. • Before you service or start the engine, fa- miliarize yourself with the snow thrower. Be sure you understand the function and location of all controls. NOTE: Check tension of[...]

COLD START (See figure on this page) • Be sure the auger ddve lever is in the disengaged (Released) position, • Move the throttle control to '_ (Fast) position. • Remove the keys from the plastic bag. Insert one key into the ignition slot. Be sure it snaps into place. DO NOT TURN KEY. Keep the second key in a safe place. • Rotate the c[...]

• Push the primer button, see figure on page 8, while covering the vent hole as follows: (remove finger from primer but- ton between primes). One time if temperature is above 50oF. Two times if temperature is 50_F to 15°t:. Four times if temperature is below 15°F. • Pull the recoil starter handle rapidly. Do not allow the handle to snap back,[...]

CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service Check Engine Oil Level Change Engine Oil Tighten All Screws & Nuts Lubricate Pivot Points Check Auger Clutch Cable Adjustment (See Cable Adj) Check Ddve Bert Check Fuel Drain Fuel Replace Spark Plug After first 2 Hours SCHEDULE SERVICE DATES Before AS Every [...]

OIL RECOMMENDATION Only use high quality detergent oil rated with API service classification SG. Select the oil's viscosity grade according to your expected operating temperature. NOTE: For extreme cold operating condi- tions of 0 ° and below, use a partial synthetic OW30 motor oil for easier starting. NOTE: Although multi-viscosity oils im- [...]

• Hold the square end of the threaded portion with pliers and adjust the Iocknut in or out until the excess slack is removed (see last figure on page 14). • Pull the cable back through the spring and connect the cable (see last figure on page 14). NOTE: Whenever the auger belt is replaced, the cables will need to be adjusted. TO ADJUST AUGER DR[...]

mounting bolt. • Reinstall the belt cover. • Reconnect the spark plug wire. A(_dve Pulley " ,_._,,,,=_. Belt Guide ,--k -'-k" .8. Auger Idler _ Pulley Enga_ it _ _ . Impeller _ Pulley TO REPLACE AUGER SHEAR BOLT The augers are secured to the auger shaft with special bolts (see figure below ) that are designed to break (to prot[...]

Z_ CAUTION' Never store your snow thrower indoors'or in an enclosed, poorly ventilated area if gasoline remains in the tank. fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below. S[...]

TROUBLE CAUSE CORRECTION )ifficult starting Defective spark plug Replace spark plug Water or dirt in fuel system Use carburetor bowl drain to flush and refill with fresh fuel. Engine runs Blocked fuel line or low on fuel Clean fuel line; check fuel supply; erratically tank or stale gasoline add fresh fuel (gasoline/oil mix tura if 2-cycle engine). [...]

19[...]