Ford 1999 Crown Victoria инструкция обслуживания

Before driving Introduction 2 Instrumentation 4 Controls and features 23 Seating and safety restraints 91 Starting and driving Starting 112 Driving 117 Roadside emergencies 132 Servicing Maintenance and care 148 Capacities and specifications 187 Customer assistance 192 Reporting safety defects 204 Index 205 All rights reserved. Reproduction by any [...]

ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regardi[...]

SPECIAL NOTICES Notice to owners of Severe Duty vehicles Before you drive your vehicle, be sure to read the “Severe Duty Owner’ s Guide Supplement.” This book contains important operation and maintenance information. Notice to owners of natural gas fueled vehicles Before you drive your vehicle, be sure to read the “Natural Gas V ehicle Owne[...]

R.DEF . AUTO LAMP 0FF PANEL DIM PUSH INTERIOR HI LO F E CHECK ENGINE AIR SUSP OD OFF BRAKE TEMP VOLTS FUEL MPH km/h 10 20 30 40 50 60 70 80 90 10 0 11 0 12 0 20 40 60 80 100 120 140 160 180 200 H C F H L < FUEL FILL DOOR P R N D 2 1 OFF ON Driver side air bag (pg. 101) Instrument cluster (pg. 21) Rear window defroster control (pg. 24) Instrument[...]

SCAN BASS TREB BAL FADE SIDE EJ REW FF 1 - 2 TAPE AMS VOL - PUSH ON SEEK TUNE AM FM CLK 12 3 456 FM1 ST L NORM A/C VENT FLOOR FLR • DEF DEF HI LO MAX A/C OUTSIDE TEMP AUTOMATIC OFF F AUTO HM OIL H L RSM SET ACC COAST Electronic sound system (pg. 34) Climate control systems (pg. 25) Clock (pg. 33) T raction control switch* (pg. 120) Gearshift (w/o[...]

W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge. The light comes on when there is approximately 1/16th of a tank indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information). The ignition must be[...]

Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service[...]

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the [...]

T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter . High beams Illuminates when the high beam headlamps are turned on. Charging sys[...]

Never remove the coolant recovery cap while the engine is running or hot. Refer to Engine coolant in the Maintenance and care chapter . If light stays on or continues to turn on after the vehicle warms up, have your vehicle serviced. This light also illuminates briefly when the ignition key is turned to ON. Air suspension (if equipped) This light t[...]

• the customer has disabled the system using the traction control switch. For more information, refer to the Driving chapter . Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter . Supplemental restraint system (SRS) warnin[...]

Optional instrument cluster gauges Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty , there is a small amount of[...]

• Optional instrument cluster This shows the approximate amount of fuel in the fuel tank in whole numbers (liters or gallons). If your tank is full or nearly full, the display will be “F”. If your tank is empty or nearly empty , the display will be “E”. Speedometer Indicates the current vehicle speed. • Standard instrument cluster • O[...]

Odometer Registers the total kilometers (miles) of the vehicle. • Standard instrument cluster • Optional instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. R[...]

Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the ignition and let it cool. Refer [...]

Battery voltage gauge (if equipped) This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge (if equipped) This shows the engine oil pressure in the sys[...]

• see when overdrive has been deactivated • monitor the average fuel economy • check the distance traveled during a trip on either T rip A or T rip B • monitor the average speed Selectable features Reset Press this control to reset the selected message center function to zero. The only functions which can be reset are: • A VG ECON • TRI[...]

1. Push either the right or left side of the SELECT control to choose the desired function. 2. Press the RESET control and the selected message center function will be reset to zero. Message center functions DIST TO EMPTY (DTE) This function estimates approximately how far you can drive with the fuel remaining in your tank under normal driving cond[...]

If “CO” or “CS” is displayed, there is a problem with the fuel indication system and you should contact your dealer for service as soon as possible. A VG ECON (average fuel economy) Select this function to display your average fuel economy in liters/100 km or miles/gallon. If you calculate your average fuel economy by dividing miles travele[...]

T o reset either trip feature to zero, press the RESET control while the appropriate trip distance feature (TRIP A or TRIP B) is displayed. A VG SPEED (average speed) Select this function to display your average speed in miles per hour or kilometers per hour . Y our vehicle must be moving to calculate your average speed. When your vehicle is not mo[...]

Door ajar Illuminates when one of the doors is not completely shut and the ignition is turned to ON. W ith the ignition ON, this light will flash five times and sound a tone for one second, then remain on (if a door is open). Low washer fluid Momentarily illuminates when the ignition is turned to ON and will stay on when the windshield washer fluid[...]

If the T raction Control y indicator comes on or stays lit, either: • the T raction Control y system needs service, or • the customer has disabled the system using the traction control switch. For more information, refer to the Driving chapter . Anti-lock brake system (ABS) (If equipped) Momentarily illuminates when the ignition is turned on an[...]

P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Push up to brighten. • Push down to dim. HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. High beams Push forward to ac[...]

Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is turned to OFF . • T o turn autolamps on, rotate the control counterclock[...]

The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. T o manually turn off the defroster before ten minutes have passed, push the control again. CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle.[...]

Under normal conditions, your vehicle’ s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than NORM A/C but more economical and will cool [...]

Operating tips • In humid weather , select before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position. • T o prevent humidity buildup inside the vehicle, don’ t drive with the climate control system in the OFF position. • Don’t put objects under the front seat that will interfere with [...]

Turning the EA TC on Press AUTOMA TIC, any of the override controls or the fan speed control. The EA TC will only operate when the ignition is in the ON position. Turning the EA TC off Press OFF . The Outside T emperature function will continue to operate until the ignition is turned off. Automatic operation Press AUTOMA TIC and select the desired [...]

T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 15°C (59°F) is shown in the display window . The EA TC will continue maximum cooling (disregarding the displayed temperature) until a warmer t[...]

Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed. The display will show to indicate manu[...]

• MAX A/C-Uses recirculated air to cool the vehicle. The temperature display will remain the same and air will be cooled based on the selected temperature. T o exit, press AUTOMA TIC or any other override controls. MAX A/C is noisier than NORM A/C but more economical and will cool the inside of the vehicle faster . Airflow is from the instrument [...]

Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to[...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the v[...]

USING YOUR AUDIO SYSTEM AM/FM Stereo V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 1 2 3 4 AM[...]

AM/FM select The AM/FM select control works in radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band[...]

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass adjust The b[...]

Speaker fade adjust (if equipped) Speaker sound can be adjusted between the front and rear speakers. W ith the electronic AM/FM stereo, press the TONE control four times, then use the volume knob to adjust the level. Setting the clock Press CLK to toggle between listening frequencies and clock mode. T o set the hour , press and hold the CLK control[...]

• to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Anytime that the [...]

V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in [...]

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there[...]

Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass adjus[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape select • T o enter tape mode while in radio mode, press the T APE AMS control. Automatic Music Search The Automatic Music Search feature allows you to q[...]

selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least 4 seconds duration between programs. Rewind The rewind control works in tape mode. T o rewind in tape mode, press the REW control. Ra[...]

Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode. T o set the hour , press and hold the CLK control and press: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes. The CLK control will [...]

When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.), the media information will again display for ten seconds before reverting back to the clock. In media mode, the media information will always be disp[...]

T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to se[...]

Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in CD mode • Press to listen to the next selection. • Press to listen to the previous selection. [...]

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autoset memory pr[...]

Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker s[...]

CD select • T o begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. Eject function Press the control to stop and eject a CD. Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening l[...]

T o set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes. Premium AM/FM Stereo/Cassette/Premium Sound with DSP Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any[...]

individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off. V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower vol[...]

Tune adjust The tune control works in radio or CD mode (if equipped). Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable stat[...]

Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc. After the last track has been completed, the [...]

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autoset memory pr[...]

Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape/CD select (if equipped) • T o begin tape[...]

Rewind The rewind control works in tape and CD modes (if equipped). • In tape mode, radio play will continue until rewind is stopped (with the T APE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results[...]

Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order . If equipped with the CD changer , the shuffle[...]

Traf fic • Press the RDS control until TRAFFIC is displayed. • Use the SEL control to select ON or OFF . W ith the feature on, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data). Program type • Press the RDS control until FIND program type is displayed. • Use the SEL control t[...]

Show • RDS sends information with the FM broadcast: station name, station type, and/or radio text. • W ith RDS activated, press the RDS control until SHOW is displayed. • Use the SEL control to select (program) TYPE, (station) NAME or NONE (no text displayed). Mute mode Press the control to mute the playing media. Press the control again to r[...]

• NEWS—“voice-only” type of sound with a limited audio band. Press the DSP control until one of the following appears: • ALL SEA TS • DRIVER SEA T • REAR SEA TS Use the SELECT control to change the equalization to the desired mode. CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk ?[...]

2. Press to eject the magazine. 3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A).[...]

5. Line up the CD with the groove of the disc holder . Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks securely into the magazine. If the disc holders are not fully locked into the magazine, the unit will not operate. Ensure that the disc holder is evenly inserted and at the same level as the magazine [...]

• The disc is dusty or defective. • The player’ s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing. If necessary , clean discs only with an appr[...]

Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.9, 88.1–107.1, 107.9 MHz Not all frequencies are used in a given area. Radi[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. The flash rate of the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb (front or rear) is burned out. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to t[...]

POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuit[...]

OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy . The overdrive function allows automatic upshifts to second, third and fourth gear . Deactivating overdrive Press the T ransmission Control Switch (TCS) located on the end of the gearshift lever . The T ransmission Control Indicator Light (TCI[...]

Do not shift the gearshift lever into N (Neutral) with the speed control on. T o turn speed control off • Press OFF or • T urn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be [...]

Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. T o set a higher set speed • Press and hold SET/SET ACC/ SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET/SET ACC/ SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Acce[...]

• Depress the brake pedal. When the desired vehicle speed is reached, press SET/SET ACC/ SET ACCEL. T o disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. COAST RESUME SET ACCEL OFF ON Controls and featu[...]

T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/ RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the i[...]

Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLink t Universal T ransce[...]

T o program your hand-held transmitters: • continue to hold the button on the HomeLink t Universal T ransceiver . • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLink T Universal T ransceiver Once programmed, the HomeLink t Universal T ransceiver [...]

3. Press and release the programmed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door . The HomeLink t Universal T ransceiver has now[...]

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Y our vehicle is equipped with an inside rear view mirror which has an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror . When the mirror detects bright light from front or behind, it wil[...]

Compass zone adjustment 1. Determine which compass zone you are in by referring to the zone map. 2. W ith the compass display turned on, press and hold the COMP side of the control until the zone selection number appears in the mirror display window . 3. Release the COMP side of the control, then press it down again. 4. Continue to press until your[...]

2. Press and hold the COMP side of the control for approximately six seconds until “C” appears in the mirror display . 3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles or on your everyday routine until the display reads a direction. 4. The compass is now calibrated. T RUNK REMOTE CONTROL The remote trunk release control is loca[...]

• Press the bottom portion of the rocker switch to open. Express down • Press AUTO and release quickly . The window will open fully . Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side[...]

POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors. POWER SIDE VIEW MIRRORS The power mirrors can be operated at any time. T o adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center positio[...]

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatically set the lock for b[...]

Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. The horn will chirp and the parklamps/taillamps will flash to confirm the control was pressed. This feature can b[...]

1. Enter the keyless entry keypad factory-set code. 2. W ithin 5 seconds press and hold 7/8 control. 3. W ithin 5 seconds with 7/8 held down, press and release 1/2 control. 4. Release 7/8 control. The doors will lock/unlock to confirm successful programming. Autolock (if equipped) This feature automatically locks all doors when: • all vehicle doo[...]

Y ou must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. T urn the ignition key to ON. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition key from ON to OFF . 4. Press the power door unlock control three time[...]

Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the i[...]

3. Snap the two halves back together . Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement. Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additi[...]

as your SecuriLock y key may cause vehicle starting problems. These objects and devices cannot damage the SecuriLock y key , but can cause a momentary problem if they are too close to the key when starting the engine. If a problem occurs, turn ignition off and restart the engine with all other objects on the key ring held away from the SecuriLock y[...]

KEYLESS ENTRY SYSTEM W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key . • open trunk • disable/enable horn chirp. • disable/enable autolock See also Remote entry system in this chapter for more information. Y our vehicle has a factory-set 5–digit code that operates the keyless entry system.[...]

Y ou can program up to three personal codes to unlock your vehicle. These codes do not replace the permanent code that the dealership gave you. Erasing personal code T o erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 2. Press 1/2 within 5 seconds of step 1. 3. Press and hold 1/2 for two seconds. All of[...]

Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. T o lock the doors: 1. Press 7/8 and 9/0 at the same time. 1 2 3 45 67 8 9 0 Controls and features 90[...]

SEA TING Head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to t[...]

Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the manual recline function (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright[...]

• Release the handle when the desired position has been reached. Adjusting the power front seats – door mounted controls The controls for the power seats are located on the inside of each front door . Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in[...]

Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. Adjusting the power seats – seat mounted controls Never adjust the driver’ s seat or seatback when the vehicle is moving. The power seat controls are located on the side of the driver’ s seat. Press to raise or lower [...]

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low ac[...]

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder . 3) Never use a[...]

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is desired. • Anytime a child safety seat is insta[...]

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensiti[...]

Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the w[...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air [...]

Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably . • Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area m[...]

How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wro[...]

Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger air bag mo[...]

Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air[...]

Do not leave children, unreliable adults, or pets unattended in your vehicle. T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the ch[...]

Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collision. When installing a[...]

Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. Children 12 and under should be p[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in pla[...]

5. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt. 6. Before placing the child into the child seat, forcibly tilt the child seat from side to side and in forward direction to make sure that the seat is held securely in place. If the child seat moves excessively , repeat steps 5 through 6, or p[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accele[...]

2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. T urn the key to 4 (ON) without turning the key to 5 (ST ART). BRAKE HOOD 1 2 3 4 5 Starting 113[...]

Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light ( ) will not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return[...]

2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try , turn the key to OFF , wait ten seconds and try again. 3. If the temperature is below -12°C (10°F) and the engine does not start in fifteen seconds on the first try , turn the key OFF and wait ten seconds and try again. If the engin[...]

Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately . Do not drive if you smell exhaust fumes. These fumes are harmful a[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. W ith the ABS light on, the anti-lock brake system is disabled and normal braking is s[...]

The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. The parking brake is not recommended to stop a[...]

T RACTION CONTROL Y (IF EQUIPPED) Y our vehicle may be equipped with the optional T raction Control y system. This system helps you maintain the stability and steerability of your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates by detecting and controlling wheel spin. The system borrows many of the elect[...]

The traction control indicator flashes during a T raction Control y system event. If the traction control indicator comes on and stays lit, either: • the T raction Control y system requires service, or • the customer has disabled the system using the traction control switch located on the left side of the glove compartment. The T raction Contro[...]

Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes at a constant vehicle speed, have the power steering system checked by your dealer or a q[...]

T RANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remov[...]

Driving with a 4–speed automatic transmission Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift. Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure so[...]

Overdrive The normal driving position for the best fuel economy . T ransmission operates in gears one through four . Overdrive can be deactivated by pressing the transmission control switch on the gearshift lever . The transmission control indicator light (TCIL) will illuminate on the instrument cluster . Drive Not shown on the display . Activate b[...]

1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to Overdrive. Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear , and will shift to 1 (Low) after vehicle decelerates to the proper speed. T RACTION-LOK AXLE (IF EQUIPPED) This axle provide[...]

• GCW (Gross Combined W eight) : The combined weight of the towing vehicle (including passengers and cargo) and the trailer . • GCWR (Gross Combined W eight Rating) : Maximum combined weight of the towing vehicle (including passengers and cargo) and the trailer . The GCWR indicates the maximum loaded weight that the vehicle is designed to tow .[...]

Always ensure that the weight of passengers, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both Gross V ehicle W eight and Front and Rear Gross Axle W eight Rating limits. Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitat[...]

If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper . Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulatio[...]

T railer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be 1[...]

If driving through deep or standing water is unavoidable, proceed very slowly . Never drive through water that is higher than the bottom of the hubs. Once through the water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on [...]

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously . • Depress control again to [...]

The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner . Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in the reset button. 4. T ur[...]

Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — ?[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 15A Brake Pedal Position (BPP) Switch, Multi-Function Switch, Speed Control 2 30A W iper Control Module, W indshield W iper Motor 3 — Not Used 4 15A Lighting Control Module, Main Light Switch 5 15A Backup Lamps, V ariable Assist Power Steering (V APS), T urn Signals[...]

Fuse/Relay Location Fuse Amp Rating Description 9 30A Blower Motor , A/C-Heater Mode Switch 10 10A Air Bag Module 11 5A Radio 12 18A CB Lighting Control Module, Flash-to-Pass, Main Light Switch 13 15A W arning Lamps, Analog Cluster Gauges and Indicators, Electronic Automatic T ransmission, Lighting Control Module 14 20A CB W indow/Door Lock Control[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 20A* Electric Fuel Pump Relay 2 30A* Generator , Starter Relay , Fuses 15 and 18 3 25A* Radio, CD Changer , Subwoofer Amplifier 4 30A* Police Power Relay 5 15A* Horn Relay 6 20A* DRL Module 7 20A CB Power door Locks, Power Seats, T runk Lid Release 8 30A*[...]

Fuse/Relay Location Fuse Amp Rating Description 12 30A** PCM Power Relay , PCM, Natural Gas V ehicle Module 13 50A** High Speed Cooling Fan Relay 14 40A** Rear W indow Defrost Relay , Also see Fuse 17 15 50A** Anti-Lock Brake Module 16 50A** Police Option Fuse Holder 17 30A CB Cooling Fan Relay Relay 1 — Rear Defrost Relay Relay 2 — Horn Relay [...]

When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’ s reduced ground clearance • try to repair the[...]

5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Refer to Anti-theft lug nuts for information on removing anti-theft lug nuts. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspen[...]

T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the rear differential as a jacking point. 7. Remove the lug nuts with the lug wrench. 8. Replace the flat tire with t[...]

Removing the anti-theft lug nut 1. Insert the key over the locking lug nut. Make sure you hold the key square to the lug nut. If you hold the key at an angle, you could damage the key and the lug nut. 2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench. 3. T urn the wrench in a counterclockwise direction t[...]

3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tig[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the[...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Before your vehi[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your ?[...]

Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3. Lift the hood until the lif[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. W indshield washer fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Battery 9. Automatic transmission fluid dipstick 9 1 2 3 6 5 7 8 4 Maintenance and[...]

ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). [...]

• If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, [...]

Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty . Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide. Ford production and aftermarket [...]

If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry . This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level[...]

maintenance, refer to Adding engine coolant in this chapter . Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid. Do not mix conventional gr[...]

Change your engine coolant according to the appropriate schedule listed in the Scheduled Maintenance Guide. Use Ford Premium Engine Coolant E2FZ-19549–AA (in Oregon, F5FZ-19549–CC, in Canada, Motorcraft CXC-10) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44–A. DO NOT USE Ford Extended Life Engine Coolant F6AZ[...]

What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works • Standard cluster • Optional cluster[...]

When this occurs the vehicle will still operate, however: • the engine power will be limited. • the air conditioning system will be disabled. Continued operation will increase the engine temperature: • the symbol will begin to flash. • if your vehicle is equipped with digital gauges, the gauge bars will flash and a tone will sound every fiv[...]

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary , use only MERCON t AT F . 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near th[...]

Automatic transmission fluid expands when warmed. T o obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for [...]

The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating [...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte l[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sa[...]

INFORMA TION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These T ire Quality Grades are determined by standards that the United States Department of T ransportation has set. T ire Quality Grades apply to new pneumatic tires for use on passenge[...]

T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire li[...]

• Four tire rotation (for vehicles with aluminum wheels) • Five tire rotation (for vehicles with steel wheels and full size spare tires) Maintenance and care 167[...]

Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity . Use only the tire co[...]

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same [...]

The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the cap. Automotive fuels can cause serious injury or death if misused or mishandled. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open[...]

splashed on the skin, promptly wash skin thoroughly with soap and water . Consult a physician immediately if you experience an adverse reaction. Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a one-eighth turn on/off feature. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise[...]

Do not use gasolines containing methanol. It can damage critical fuel systems components. V ehicles certified to meet California emission standards (indicated on the underhood V ehicle Emissions Control Information label) are designed to operate on California cleaner -burning, low-sulfur gasolines. If you have a California-certified vehicle and Cal[...]

Cleaner air Ford approves the use of gasolines to improve air quality , including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE. Running out of fuel A void running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to crank the engine sev[...]

the Indicated Capacity and the Empty Reserve combined. Indicated Capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty Reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty . The amount of Empty Reserve varies and should not be reli[...]

economy . Additionally , keeping records during summer and winter will show how temperature impacts fuel economy . In general, lower temperatures give lower fuel economy . Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel econo[...]

• Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • C[...]

• Use only unleaded fuel. • A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule. The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to [...]

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the W arning Lights and Chimes section of the Instrumentation chapter . Y our vehicle may not pass the I/[...]

Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then [...]

2. Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating it clockwise until you feel a “stop.” 3. Connect the electrical connector into the rear of the plastic base until it snaps, locking it into position. 4. Install the protective cover over headlamps locking it in place with three knobs. 5[...]

High-mount brakelamp bulbs 1. Open trunk. 2. Inside trunk, locate access hole under the rear window 3. Remove the bulb socket by rotating it 45 degrees and pulling it out of the lamp assembly . 4. Carefully pull bulb straight out of socket and push in new bulb. 5. T o complete installation, follow the removal procedure in reverse order . Replacing [...]

Using the right bulbs Function T rade Number Headlamp 9007 Park lamp and turn lamp (front) 3457 NAK Side marker (front) 194 NA Cornering lamp (front) 3156K T ail, stop, turn (rear) 3157 K Side marker (rear) 194 Backup lamp 3156K License plate lamp 168 High-mount brakelamp 912 Luggage compartment lamp 212-2 Dome lamp 906 Rear reading lamp 211-2 Map [...]

W ashing your vehicle W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. T o avoid spots, avoid washing when the hood is still warm, i[...]

Cleaning the wheels W ash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar . The brushes used in some automatic car washes may damage [...]

• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, sol[...]

Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary . Cleaning and maintaining the safety belts Clean the safety belts with a mild soap [...]

MOTORCRAFT PART NUMBERS Component 4.6L SOHC V8 engine Air filter element F A-1668 Fuel filter FG-986B Battery (standard) BXT -59 Battery (optional) BXT -65-650 Oil filter FL-820-S PCV valve EV -98 Spark plugs* A WSF-32P * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part N[...]

rear axle lubricant. Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole. Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST -M2C118–A for complete refill of T raction-Lok axles. LUBRICANT SPECIFICATIONS Item Ford part nam[...]

Item Ford part name Ford part number Ford specification Rear axle lubricant 1 Motorcraft SAE 80W90 Premium Rear Axle Lubricant XY -80W90-QL WSP-M2C197_A W indshield washer fluid Ultra-Clear W indshield W asher Concentrate C9AZ-19550-AC ESR-M17P5-A 1 Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST -M2C118–A[...]

3 5 2 4 1 Capacities and specifications 190[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. V ehicle identification number [...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

Ford extended service plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides: • Protection against repair co[...]

Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs. Certain warra[...]

Please have the following information available when contacting Ford Customer Assistance: • Y our telephone number (home and business) • The name of the dealer and the city where the dealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number[...]

• sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’ s performance as designed • a request for reimbursement of consequential expenses unless a service or product concern being reviewed • items not covered by the New V ehicle Limited W arranty (including maintenance and wea[...]

• the toll-free phone number of the DSB’ s independent administrator Y our dealership and a Ford Motor Company representative are asked to submit statements at this time. T o properly review your case, the Board needs the following information: • legible copies of all documents and maintenance or repair orders relevant to the case • the yea[...]

After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’ s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law . T o Request a DSB Brochure/Appli[...]

If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S[...]

Ford T riple Clean Ford Ultra-Clear Spray Glass Cleaner * May be sold with the Motorcraft name A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complemen[...]

T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running [...]

Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates T ailgate covers T ailgate [...]

• The Federal Communications Commission (FCC) and Canadian Radio T elecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and shou[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

Air bag supplemental restraint system ........................ 101 and child safety seats ............ 102 description .............................. 101 disposal .................................... 105 indicator light .........................104 passenger air bag ................... 103 Air conditioning automatic temperature control system .....[...]

detergent in fuel ..................... 173 filling your vehicle with fuel ........................... 169,171 quality ...................................... 172 running out of fuel ................. 173 safety information relating to automotive fuels ..................... 169 Fuses ...................................133,134 Gas mileage (see Fuel e[...]

Radio ....34,35,36,37,38,39,40,41,42 43,44,45,46,47,48,49,50,51 52,53,54,55,56,57,58,59,60 Relays .................................133,138 Remote entry system ............81,84 illuminated entry ...................... 85 locking/unlocking doors ........... 82 replacement/additional transmitters ............................... 86 replacing the batte[...]

Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity 71.9L (19.0 gallons) Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. T ire pressure and size Refer to the Certification Label located on the driver’ s door . Hood release Pull handle unde[...]